Epson PowerLite 8000i, PowerLite 9000i, PowerLite 8000NL, PowerLite 9000NL Quick Start Guide

EPSON®Multimedia Projector

desk

video-out cable

Quick Setup

Make sure your EPSON®PowerLite®projector and computer are turned off. Then follow these steps:

EPSON PowerLite 8000i EPSON PowerLite 9000i

Connecting to a

Laptop

Connect one end of the projector video cable to

2 3

If you want to use the remote control as a mouse, see below. If not, just follow the steps in “Using Your Projector” (see other side).

the projector’s Computer 1 port.

Connect the other end of the video cable to the laptop’s monitor port.

Connect the power cord to the projector.

2 3

Connecting to a

Macintosh

PowerBook

Connect one end of the projector video cable

Connect the small terminal of the desktop adapter to the other end of the projector video cable.(Be sure the desktop adapter DIP switches are set correctly for the resolution you want.See your PowerBook manual.)

Connect the projector video cable (with Macintosh desktop adapter attached) to the video-out port of your PowerBook.

Note: If your PowerBook requires a video-out cable (not included), connect the smaller end of the cable to the video-out port on the back of the PowerBook.Then connect the other end to the desktop adapter.

to the projector’s Computer 1 port.

desktop adapter

video-out cable

Optional Connections

To use your remote control as a mouse or to use audio,follow these steps:

Connect the round end of the main cable to the projector’s Mouse/Com 1 port.

Connect the PS/2 or USB cable to the MOUSE terminal on the main cable.

Connect the other end of the PS/2 or USB cable to the mouse or USB port on your laptop.

main cable

Connect the power cord

If you want to use the remote control as a mouse, see below. If not, just follow the steps in “Using Your Projector” (see other side).

to the projector.

Optional Connections

To use your remote control as a mouse or use audio,follow these steps:

1 2

Connect the round end of the main cable to the projector’s Mouse/Com 1 port.

Connect the Mac or USB cable to the MOUSE terminal on the main cable.

Connect the other end of the Mac or USB cable to the mouse or USB port on your PowerBook.

main cable

To use audio,connect one end of the audio cable to the projector’s Audio 1

jack and the other end to your laptop.

To use audio,connect one end of the audio cable to the projector’s Audio 1 jack and

the other end to your PowerBook.

EPSON

ESC

EPSON PowerLite 8000i

Projector at a Glance

Using the Control Panel

Help

Displays the projector’s

online help

Power button

Turns projector

on and off

Computer

Switches connected

computer sources

sequentially

A/V Mute

Turns off the audio-video

Displays or hides the menu

Esc

Ends the current function; returns to previous screen/menu

Enter button

Registers a menu selection

Tracking +,Tracking -

(right and left arrows)

Adjusts projector to match the computer signal

Optical keystone adjustment knob

Control panel

EPSON PowerLite 9000i

Focus ring

Zoom ring

Resize

Provides display

options for multiple

resolutions

Video

Switches to the

video input source

Adjusts the volume

- Volume +

when used in conjunction with the Shift button

Using the Remote Control

Freeze

Freezes the computer

or video image

A/V Mute

Turns off the

audio-video

- Keystone +

Adjusts a trapezoid image to a normal rectangle

Power

Starts or stops the projector

RC on/off

Turns the remote control on or off

Sync +, Sync -

(up and down arrows)

Adjusts projector to match the computer signal

Foot adjust levers

Using Y our Projector

1. Plug in the projector. The power light on the projector’s control panel

turns orange. (The projector is not on yet.)

2. Remove the lens cap.

3. Press the Power button on the control panel or remote control

once to turn on. The power light flashes green as the projector

warms up. Then turn on your computer.

Warning: Never look into the lens when the lamp is on.

4. You can set the display to appear on both the computer’s screen and

Help

the projector. Check your computer manual for instructions.

Infrared receiver

E-Zoom

Enlarges or reduces

the image size

Illumination

Illuminates all buttons

on the remote control

Esc

Ends the

current function;

returns to previous

menu/screen;

acts as a right

mouse-click when the

image source is

Computer

Effects buttons

(1-5)

Display preprogrammed special effects

Enter (Pointer)

Navigates menu system; acts as a mouse pointer; acts as a left mouse-click when the image source is Computer

Comp1

S-Video

- Volume +

Auto

P in P

BNC

Video

Resize

Preset

5. To adjust the projected image size,rotate the zoom (outside) ring

on the projector. For larger adjustments,you may need to reposition the projector closer to or farther from the screen.

6. To focus the image, rotate the focus (inside) ring.

7. If the image is too high or low,lift up the foot adjust levers to raise

or lower the adjustable feet.Release the levers to lock the feet in place.

8. When you want to stop projecting images,press the Power button

again.The projection light flashes orange as the projector cools down. When you are done,make sure the projection light has stopped flashing and then unplug the power cord.

Caution: Never unplug the power cord when the power light

is green;this may damage the lamp.

For instructions on setting up your projector with a desktop computer or for information on using the ELP Link IV software to control the projector,see your User’s Guide.

CPD 9113