Epson PowerLite 5300, PowerLite 7200, PowerLite 7300 User Manual
EPSON PowerLite®
5300/7200/7300 User’s Guide
All rights reserved. No part of this publicatio n may be repro duced, stored in a retrie val system, or transm itted
in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior
written permission of SEIKO EPSON CORPORATION. No patent lia bility is assumed with respect to the use
of the information contained h erein. Neither is any li ability assumed for da mages resulting from the use of the
information contained herein.
Neither SEIKO EPSON CORPORATION nor its affiliates shall be liable to the purchaser of this product or
third parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a resul t of:
accident, misuse, or abuse of this product or un authorized modifications, repairs, or alterations to this product,
or (excluding the U.S.) failure to strictly comply with SEIKO EPSON CORPORATION’s operating and
maintenance instructions.
SEIKO EPSON CORPORATION shall not be liable against any damages or problems arising from the use of
any options o r a ny con sum able pro duct s ot he r t han thos e d esi gnat ed as O ri gina l EPSO N P rod ucts or EPS ON
Approved Products by SEIKO EPSON CORPORATION.
EPSON and PowerLite are registered trademarks of SEIKO EPSON CORPORATION.
SoundAdvice is a service mark and FaxAdvice is a trademark of Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks
of their respective owners. EPSON disclaims any and all rights in those marks.
Copyright © 1998 by Epson America, Inc. CPD-7925
Torrance, California, USA 7541655
12/98
Important Information About Your Projector
Important Safety Information
WARNING: Never look into the project or lens wh en the lamp is turned o n; th e brigh t ligh t can damag e your
eyes. Never let children look into the lens when it is on. Never open any cover on the projector, except the
lamp and filter covers. Dangerous electrical voltages inside the projector can severely injure you. Except as
specifically explained in this User’s Guid e, do not attempt to service this prod uct yourself. Ref er all servicing
to qualified service personnel.
WARNING: The projector and its accessories come packaged in plastic bags. Keep plastic bags away from
small children to avoid any risk of suffocation.
Caution: When you replace the lamp, never touch the new lamp with your bare hands; the invisible residue
left by the oil on your hands may shorten the lamp life. Use a cloth or glove to handle the new lamp.
Remote Control Information
You can operate the projector by remote control via a line-of-sight infrared (IR) receiver at the front and rear
of the projector. The projector may not respond to remote control commands under the following conditions:
❐ There is an object between the remote control IR emitter and the IR receiver on the projector.
❐ Ambient light is too bright.
❐ Certain types of fluorescent lighting are used.
❐ A strong light source shines into the IR receiver.
❐ Other equipment that emits infrared energy, such as a radiant room heater, is in the room.
These conditions commonly cause problems for most infrared-co n troll ed equip m ent. Try the followin g:
❐ The remote control unit’s batteries may be low on power; replace them.
❐ Dim the ambient lighting and/or turn off any fluorescent lights.
❐ Close any window coveri ngs and/or move the projector out of direct sunlight.
❐ Turn off other equipment that emits infrared energy.
If the remote control still does not work properly, remember you can always control your computer-based
presentation directly from the com puter, even i n an environm ent contain ing one of t he conditions listed above.
FCC Compliance Statement
For United States Users
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio or television reception. However, there is no guarantee that interference will not occur in a particular
installation. If this equipme nt does cause interference to radio and television reception, which can be
determined by turning the equ ip ment off and on, the user is encouraged t o t r y to correct the interference by
one or more of the following measures.
❐ Reorient or relocate the receiving antenna.
❐ Increase the separation between the equi pment and receiver.
❐ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
❐ Consult the dealer or an experienced radio/TV technician for help.
WARNING
The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC
Certification of this device and may cause int erference levels whic h exceed the limits establi shed by the FCC
for this equipment. It is the responsibility of the user to obtain and use a shielded equipment interface cable
with this device. If this equipment has more than one interface con nector, do not leave cables connected to
unused interfaces . Changes or modifi cations not expre ssly approved by the manufactur er could void the us er’s
authority to operate the equipment.
For Canadian Users
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations.
Cet appareil numérique de la classe B respecte toute s les exigences du Rè glement sur le materiel b rouilleur du
Canada.
Contents
Introduction 1
Getting the Most Out of Your Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
About This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Where to Get Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Electronic Support Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Automated Telephone Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1
Setting Up the Projector 11
Unpacking the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Additional Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Before You Connect the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Installing the Remote Control Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
i
Connecting to a Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Connecting to a PC Desktop Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Connecting to a PC Laptop Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Connecting to a Desktop Macintosh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Connecting to a PowerBook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Connecting to a High-End Workstation . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Connecting to a Video Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Connecting to an External Speaker or PA System . . . . . . . . . . . . . . . . . . . . . . . . .53
Turning the Equipment On and Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Turning the Projector On and Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
2
Using the Projector 57
Positioning the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Calculating Image Size and Projection Distance . . . . . . . . . . . . . . . . . . . . . . .60
Focusing and Positioning the Screen Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Resize Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Sleep Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Controlling the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Using the Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Using the Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
Projector Status Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
3
Using the Projector Menus 75
Accessing the Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
Changing a Menu Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Video Menu (Image Source = Computer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
Video Menu (Image Source = Video) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
Audio Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
Options Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
ii
Custom Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
About Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Reset All Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
4
Using the ELP Link III Software 91
Installing the Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Connecting Needed Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Installing the Software for Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Installing the Software for a Macintosh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Launching the Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Launching the Software from Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Launching the Software on a Macintosh . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Using the Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Customizing the Remote Control Effects Buttons . . . . . . . . . . . . . . . . . . . . . 96
Controlling Projector Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
5
Maintenance 117
Cleaning the Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Cleaning the Projector Case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Cleaning the Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Replacing the Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Transporting the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
6
Troubleshooting 125
Problems with the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Problems with the Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Problems with the Image or Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
iii
7
Technical Specifications 133
Supported Monitor Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137
Glossary 139
Index 141
iv
Introduction
Your PowerLite® projector is a brilliant, lightweight, portable
projector that allows you to project full-color images and video onto a
large screen for presentations. You can connect it simultaneously to
three image sources: two computers or workstation sources, plus one
video source, such as a VCR or camcorder. You can also connect audio
for each image source.
Images are displayed in full color (16,770,000 colors) at an SVGA
resolution of 800 × 600 pixels on the PowerLite 5300, or an XGA
resolution of 1024 × 768 pixels on the PowerLite 7200 and PowerLite
7300. The projector supports a wide variety of video inputs, from
VGA to SXGA with resolutions up to 1280 × 1024. It produces bright
images that can be easily seen in rooms light enough to take notes.
Your projector’s two speakers employ a built-in 3D Sound System for
rich, powerful audio output. You can even connect an external speaker
when further amplification is required.
1
For your presentations, you can select front, rear, or ceiling projection.
This provides maximum flexibility in choosing the best display
method for each environment.
You control your projector through a hand-held remote control unit,
with menus provided for image source switching and image
adjustment. The remote control can also act as a wireless mouse to
control operations on your computer screen during presentations.
Additionally, you can install the projector’s ELP Link III software to
control the projector’s settings from your computer and enhance your
presentations with special effects.
Your projector features a new patented SizeWise™ chip for support of
VGA, SVGA, XGA, and SXGA output. No matter what type of
computer output is used, the result is a full-size video image of
outstanding clarity.
The projector supports a wide range of computers and workstations:
®
compatible PCs and laptops, Apple® Macintosh,® Power
IBM
Macintosh,
the Sun
™
and PowerBook™ computers, and workstations such as
®
SPARCstation™ (The PowerLite 5300 is not recommended
for use with high-end workstations). The video source can be NTSC,
PAL, or SECAM. The projector automatically senses the video format,
which can be composite video, S-Video, or component video. See
Chapter 7 for details on supported computers and video formats.
2
Introduction
Getting the Most Out of Your Projector
Your projector comes with a full set of features that enable you to
control the settings for the image display, video, and audio. To get the
most out of the projector, read this section for a quick summary of the
important features.
Remote Control
The buttons on the remote control enable you to turn the projector on
and off, and provide direct access to blank, freeze, volume, mute, and
image source switching. Use the remote control buttons to access
custom functions (with the ELP Link III software) and the projector’s
menu system. You can even use the remote control to control your
computer in place of your computer’s mouse.
Sleep Mode
Sleep mode conserves electricity by automatically turning off the lamp
after the projector has not been used for 30 minutes. In sleep mode,
the projector remains on but the lamp is turned off, conserving
electricity, cooling the projector, and extending the life of the lamp.
Control Panel
The control panel buttons on the projector duplicate the remote
control buttons.
Getting the Most Out of Your Projector
3
Optional Accessories
To enhance your use of the projector, EPSON provides the following:
● Customized carrying cases for the projector and its cables:
Hard Shell Carrying Case ELPKS12
Soft Shell Carrying Case ELPKS10
● Replacement lamp and air filter ELPLP05
● Long throw zoom lens ELPLL01
● Communication kit cable set and computer cable so you can
connect your projector to a second computer. There is also a Mac
adapter set so you can connect to a second Macintosh. You may
also need the VGA-13W3 video cable if you’re connecting the
projector to a high-end workstation.
ELP communication cable set ELPKC04
Computer video cable ELPKC02
Mac adapter set ELPAP01
VGA-13W3 video cable ELPKC06
VGA-5BNC video cable ELPKC07
● Portable projection screen ELPSC06
● Remote control receiver module ELPST02
● Mediaphile
(personal audio system)
™
PAS ELPPAS1
®
You can purchase these accessories from your dealer or by calling
EPSON Accessories at (800) 873-7766; or visit our web site at
www.epsonsupplies.com (U.S. sales only). In Canada, please call
(800) 873-7766 for dealer referral.
4
Introduction
About This Guide
This guide describes how to set up and use the EPSON PowerLite
5300, PowerLite 7200, and PowerLite 7300 projectors. The
instructions pertain to all these models, except where otherwise noted.
Chapter 1, “Setting Up the Projector,” provides step-by-step
instructions on how to set up your projector; connect it to your
computer, video source, or other optional equipment; and turn it on.
Chapter 2, “Using the Projector,” explains how to position the
projector relative to the screen, focus and position the screen image,
control the projector using the remote control and the control panel,
and monitor the projector’s operating status.
Chapter 3, “Using the Projector Menus,” describes how to use the
projector’s built-in menus to adjust the color and image settings,
change the display of the projected image, and modify audio settings
such as bass and treble.
Chapter 4, “Using the ELP Link III Software,” explains how to use the
ELP Link III software to control the projector settings from the
computer and use the special effects functions.
Chapter 5, “Maintenance,” covers basic procedures for maintaining
your projector in good working order and gives guidelines for
transporting it.
Chapter 6, “Troubleshooting,” describes how to interpret your
projector’s warning lights and gives helpful information for avoiding
errors, optimizing image quality, and solving problems.
About This Guide
5
Chapter 7, “Technical Specifications,” lists the technical specifications
for the projector.
A Glossary and Index are provided at the end of the manual.
Where to Get Help
If you are having trouble setting up or running your projector, first see
Chapter 6, “Troubleshooting.” If you cannot resolve the problem,
EPSON provides technical assistance through electronic support
services and automated telephone services 24 hours a day. The
following tables list the contact information.
Electronic Support Services
Service Access
World Wide Web From the Internet, you can reach EPSON’s Home Page at
http://www.epson.com.
EPSON Internet FTP Site If you have Internet FTP capability, use your Web
EPSON Download Service You can call the EPSON Download Service at
EPSON Forum on
CompuServe
6
Introduction
®
browser (or other software for FTP downloading) to log
onto ftp.epson.com with the user name anonymous
and your e-mail address as the password.
(800) 442-2007. Set your communications software
to 8 data bits, 1 stop bit, no parity. Modem speed can be
up to 28.8 Kbps.
Members of CompuServe can type GO EPSON at the
menu prompt to reach the Epson America Forum.
For a free introductory CompuServe membership, call
(800) 848-8199 and ask for representative #529.
Automated Telephone Services
Service Access
EPSON SoundAdvice
EPSON FaxAdvice
EPSON Referral Service For the location of your nearest Authorized EPSON
SM
™
For pre-recorded answers to commonly asked questions
about EPSON products 24 hours a day, seven days a
week, call (800) 922-8911.
Access EPSON’s technical information library by calling
(800) 922-8911. You must provide a return fax number to
use this service.
Reseller or Customer Care Center, call (800) 922-8911.
When you need support, follow the calling instructions on the back
of the EPSON Private Line Technical Support card included with
the projector. Technical support is also available by calling
(800) 974-1202 between 6
AM
and 6PM, Pacific Time, Monday
through Friday. Toll or long distance charges may apply.
Before you call, please have the following information ready:
● Product name
● Product serial number
● Personal identification number (PIN) for EPSON Private Line
Technical Support
● Computer configuration
● Description of the problem
Where to Get Help
7
You can purchase accessories from EPSON Accessories at
(800) 873-7766, or visit our web site at www.epsonsupplies.com (U.S.
sales only). In Canada, please call (800) 873-7766 for dealer referral.
Safety Instructions
Follow these safety instructions when setting up and using the
projector:
1. Do not place the projector on an unstable cart, stand, or table.
2. Do not use the projector near water or sources of heat.
3. Use attachments only as recommended.
4. Use the type of power source indicated on the projector. If you are
not sure of the power available, consult your dealer or power
company.
5. Place the projector near a wall outlet where the plug can be easily
unplugged.
6. Insert the projector’s three-wire grounding-type plug into a
properly grounded outlet. If you have a two-prong outlet, contact
an electrician to replace it. Do not hold the plug with wet hands.
7. Take the following precautions for the plug. Failure to comply
with these precautions could result in sparks or fire.
● Do not insert the plug into an outlet with dust present.
● Insert the plug firmly into the outlet.
8
Introduction
8. Do not overload wall outlets, extension cords, or integral
convenience receptacles. This can cause fire or electric shock.
9. Do not place the projector where the cord can be walked on. This
may result in fraying or damage to the plug.
10. Unplug the projector from the wall outlet before cleaning. Use a
damp cloth for cleaning. Do not use liquid or aerosol cleaners.
11. Do not block the slots and openings in the projector case. They
provide ventilation and prevent the projector from overheating.
Do not operate the projector on a sofa, rug, or other soft surface,
or in a closed-in cabinet unless proper ventilation is provided.
12. Never push objects of any kind through cabinet slots. Never spill
liquid of any kind into the projector.
13. Except as specifically explained in this User’s Guide, do not
attempt to service this product yourself. Refer all servicing to
qualified service personnel. Opening or removing covers may
expose you to dangerous voltages and other hazards.
14. Unplug the projector during lightning storms or when it will not
be used for extended periods.
15. Do not place the projector and remote control on top of
heat-producing equipment or in a heated place, such as a car.
Safety Instructions
9
16. Unplug the projector from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
● When the power cord or plug is damaged or frayed
● If liquid has been spilled into the projector, or if it has been
exposed to rain or water
● If it does not operate normally when you follow the operating
instructions, or if it exhibits a distinct change in performance,
indicating a need for service
● If it has been dropped or the housing has been damaged.
10
Introduction
1
Setting Up the Projector
his chapter describes how to unpack your projector, connect it to
T
your other equipment, and turn everything on. The projector must be
connected to a computer or a video source such as a VCR, camcorder,
or laser disc player before it can project any images. You may also want
to set up the projector for one or more of the following:
● Connect the mouse cable to use the remote control as a wireless
mouse. Except for some laptops, this disables your computer’s
mouse. If you are also viewing the display on your monitor, you
use the remote control’s pointer to control the screen cursor.
● Provide audio for one or both image sources. The audio source can
be the computer, video source, or another device such as a stereo.
● Connect to an external speaker or PA system to amplify the audio.
11
Unpacking the Projector
When you unpack the projector, make sure you have all these
components:
● Projector
● Remote control
● 2 AA batteries
● Power cord
● Projector video cable
● Audio cable
12
● Audio/video (A/V) cable
1 • Setting Up the Projector
● Macintosh adapter set:
Macintosh desktop adapter
Macintosh monitor adapter
● Main cable (for connecting a mouse cable to
use the remote as a wireless mouse and/or a
serial cable to use the ELP Link III software)
● PS/2
● Serial mouse cable (for the PC)
● Mac mouse cable (for the Macintosh)
● PC serial cable
● Macintosh serial cable
● Projector Software CD ROM
®
mouse cable (for the PC)
Unpacking the Projector
13
You will not need all these components; your configuration will
determine which ones you need.
Save all packaging in case you need to ship the projector in the future.
Always transport the projector in its original packaging (or the
equivalent), or use a carrying case if you are carrying the projector by
hand. (See page 123 for instructions.)
Additional Components
Depending on how you plan to use the projector, you may need
additional components:
● To receive an S-Video signal, you need an S-Video cable. (One is
usually provided with your video device.) A separate cable is
required for each video source.
● To connect a second computer, you need a computer video and
audio cable.
● To connect the projector to a Macintosh PowerBook, you need a
video-out cable. (One is provided by—or can be purchased
from—Apple for all new PowerBooks that have video-out
capability.) If your PowerBook does not include one, see your
Macintosh dealer.
● To connect the projector to an external sound system, you need an
RCA-to-3.5 mm stereo audio cable. You can obtain one from your
computer dealer.
● To connect the mouse cable to your computer, you may require a
special connector, cable, or other components. You can obtain
these items from your computer dealer.
14
1 • Setting Up the Projector
Note: You can connect a Kensington MicroSaver® anti-theft device in
the hole on the projector’s right side. Contact your computer dealer.
Before You Connect the Projector
Before you start connecting the projector to your equipment, decide
where you will want to place your projector and computer or video
source. The distance between the projector and the screen determines
the actual image size. Place the projector somewhere between 4 and
54.7 feet (1.2 and 16.7 meters) away from the screen; use the general
guidelines in the table below to determine the proper distance. (For
more precise calculations, see “Positioning the Projector” on page 58.)
✦ Caution: Do not hold or lift the projector by the lens. This can damage the
lens.
Horizontal distance from projector to screen
Image size (diagonal)
200 inches (5.1 m) 324.1 inches (8.2 m) 436.5 inches (11.1 m)
100 inches (2.54 m) 160.8 inches (4.1 m) 217.1 inches (5.5 m)
80 inches (2.03 m) 128.1 inches (3.3 m) 173.1 inches (4.4 m)
60 inches (1.52 m) 95.5 inches (2.4 m) 129.2 inches (3.3 m)
40 inches (1.02 m) 62.8 inches (1.6 m) 85.3 inches (2.2 m)
30 inches (0.76 m) 46.5 inches (1.2 m) 63.3 inches (1.6 m)
23 inches (0.58 m) 35.1 inches (0.9 m) 48.0 inches (1.2 m)
Minimum Maximum
Before You Connect the Projector
15
Be sure to place the projector on a sturdy, level surface within five feet
of the computer or video source.
Installing the Remote Control Batteries
You can use the remote control as a wireless mouse instead of your
computer’s mouse to control your presentation. You can also use it to
control the projector menus and use the Effects buttons.
Follow these steps to install the batteries in the remote control:
1. Slide off the battery compartment cover.
16
1 • Setting Up the Projector
2. Insert the two AA batteries included with the projector. Make sure
the polarity of the batteries is correct.
3. Replace the battery compartment cover.
When replacing batteries, take the following precautions:
● Do not mix old and new batteries.
● Replace batteries as soon as they run out. If the batteries leak, wipe
away battery fluid with a soft cloth. If fluid gets on your hands,
wash them immediately.
● Remove batteries if you will not be using the projector for a long
period of time.
Before You Connect the Projector
17
Connecting to a Computer
You can connect the projector to any computer capable of producing
standard VGA, Super VGA, XGA, or Super XGA output, such as:
● IBM compatible desktop PCs
● IBM compatible laptop PCs
● Apple Macintosh desktop computers, including Macintosh
Quadra,
● Any Apple PowerBook with video-out capability
● (PowerLite 7200 and 7300 only) Most high-end workstations
from Sun, Silicon Graphics,
may need an adapter cable to connect to a high-end workstation;
see page 49.)
See the section that applies to your computer. Make sure both the
computer and projector are turned off before you start.
When you have finished connecting all your components, go to
page 54 to turn on the projector and equipment.
®
Macintosh Centris,® and Power Macintosh
®
IBM, and Hewlett-Packard.® (You
18
1 • Setting Up the Projector
The illustration below identifies all the interface ports on the back of
Power Inlet
Audio Out Audio 1Audio 2
Mouse/Com 1
Mouse/Com 2
IR Repeater
Computer Out
Computer 2
Computer 1
R/R-Y G/Y G Sync B/B-Y
BNC HD/Sync VD
S-Video Composite Video
the projector; you may want to refer to this as you connect your
computer or other equipment to the projector.
1
Connecting to a PC Desktop Computer
To connect the projector to your PC desktop computer, you need to:
● Connect the projector video cable and computer monitor cable
● Connect the mouse and/or serial cable (if you want to use the
remote control as a mouse or use the ELP Link III software)
● Connect the audio cable (if you’ll be projecting with audio)
Connecting to a Computer
19
Follow the steps in each section for the cables you need to connect.
Before beginning, turn off the projector and computer if they are on.
Note: Computer configurations vary. See your computer manual for the
location of the ports needed to connect your projector.
Connecting the Video and Monitor Cables
First connect the projector video cable and computer monitor cable.
Refer to this illustration while following the steps below.
Computer 1 port
projector video cable
20
Computer
Out port
1 • Setting Up the Projector
monitor cable
1. If you will be viewing the video on your computer monitor as well
as the projector screen, disconnect the monitor cable from the
video port on the back of your computer. Then connect the
monitor cable to the projector’s Computer Out port, as shown
below. (This is useful when you need to view the video output but
the projection screen is behind you.)
2. Connect one end of the projector video cable to the projector’s
Computer 1 port. (Use the Computer 2 port if you are
connecting a second computer.)
Connecting to a Computer
21
3. Connect the other end of the projector video cable to the
computer’s video port.
4. Tighten the screws on all connectors.
Connecting the Mouse and Serial Cables
If you want to use the remote control as a mouse or use the ELP
Link III software, you need to connect the main cable. It provides
connectors for:
● The PS/2 mouse cable (to use the remote control as a mouse)
● The serial cable (to use the ELP Link III software and the Effects
buttons on the remote control)
Refer to this illustration while following the steps below.
22
1 • Setting Up the Projector
Mouse/Com 1 port
main cable
PS/2 mouse cable
9-pin serial cable
Loading...