Epson LightScene EV-100, LightScene EV-105 Installation Manual

Installation Manual
Using the Product Safely
1
Safety Instructions
This guide explains how to suspend the EV-100/EV-105 from a ceiling or install it on a wall using the supplied Direct Mount.
Regarding how to handle the projector, read the User's Guide and Safety Instructions supplied with your projector and follow the instructions in these documents.
Safety Indications
The documentation and this product use graphical symbols to show how to use this product safely and correctly to prevent injury to customers and others, and damage to property.
The indications and their meaning are as follows. Make sure you understand them properly before reading the guide.
Symbol Explanation
Warning
This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling.
Caution
This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling.
General Information Indications
Symbols Explanation
Symbol indicating an action that must not be done
Symbol indicating an action that should be done
c
Symbol indicating related or useful information
Precautions on Installing the Projector
Warning
Installing the projector on a ceiling or a wall should only be performed by a professional with the necessary skills and know-how.
If installation work is not carried out correctly, the mount or the projector could fall causing injury or accident to occur.
Follow the instructions in this guide when performing installation work.
If the instructions are not followed, the mount or the projector could fall causing injury or accident to occur.
Installation should be performed by at least two people. Also, make sure you have a secure, stable footing so that you do not drop the mount or the projector.
Using the Product Safely
2
Warning
Make sure you attach the safety wire supplied with the projector to prevent the mount from falling due to earthquakes or vibrations.
Do not attach anything to this mount except for a projector from EPSON.
Otherwise, the mount may falls and could cause death or personal injury.
When installing, make sure you install a breaker (with a rated current of 10 A or less) in a location within reach.
If any problems occur during installation, turn off the internal wiring immediately.
Note the following when handling the power cable. Otherwise, it could cause a fire or electric shock.
Do not handle the plug with wet hands
Do not use a damaged or modified power cable
Do not apply excessive force to the power cable
Do not trap the cable between parts of the mount and so on during installation
When installing, do not pull or apply excessive force to the cable connected to the projector.
Do not wind cables around the projector or the mount.
When wiring cables and so on, route the cables so that it avoids the screws and bolts.
If the cables come into contact with screws or bolts, it could cause a fire or electric shock to occur.
Make sure you tighten the screws or bolts completely when installing.
If they are not tightened completely, the mount or the projector could fall causing injury or accident to occur.
Never loosen the screws or bolts after installation.
Make sure that you check for any loose screws or bolts on a regular basis, and if any are loose, tighten them completely. If they are not tightened completely, the mount or the projector could fall causing injury or accident to occur.
When securing the mount, do not use adhesives to prevent the screws from loosening, and do not use lubricants, oils, and so on.
If you use adhesives to prevent the screws from loosening, or if you use things such as lubricants or oils, the mount or the projector case may crack causing an injury or an accident.
Do not hang from the mount or the projector, and do not place heavy objects on them.
Otherwise, the mount or the projector may fall and could cause death or injury.
Do not apply excessive force to the projector or the mount when installing.
Otherwise, the mount or the projector may be damaged and could cause death or injury.
Do not install in the following situations. Contact your local dealer or Epson Service Call Center.
If the product has been dropped or damaged before or during installation
If the mount is abnormal or damaged
Using the Product Safely
3
Warnings and Cautions on the Installation Locations
Warning
Do not attach this mount to the floor.
This mount can only be installed on a ceiling or a wall.
Check the structure and material of the surface to which the mount will be installed, and use the optimum installation method.
Make sure the surface to which the mount will be installed is strong enough.
The total maximum weight of the projector and Direct Mount is approximately 7.0 kg (approx. 5.1 kg for the projector/approx. 1.9 kg for the Direct Mount) (not including cables).
Do not install the mount or projector in an unstable location where it might be subjected to vibrations or shocks.
The surface to which the mount is attached may be damaged. Also, the mount or projector may fall and cause an injury or accident to occur.
Do not install or use the projector in locations where it could be exposed to rain or water, such as outdoors, in baths or shower rooms.
Otherwise, it could cause a fire or electric shock.
Do not use the projector in a location subject to combustible or explosive gas.
If the inside of the projector gets too hot, it could ignite and cause a fire.
Do not cover the projector's air intake vent or air exhaust vent.
If either of the vents are covered, the projector's internal temperature could rise and cause a fire.
Caution
Do not install the projector in a location outside the projector's operating temperature range.
Such an environment may damage the projector.
Install it away from air outlets such as air conditioners.
If the air from an air conditioner and so on flows directly over the projector, the temperature rises and the projector may not operate correctly.
Install it away from fluorescent lights.
Some kinds of fluorescent lights could interfere with the remote control of the projector.
Install it in a location where strong light such as fluorescent light and direct sunlight does not shine on the remote receiver.
If strong rays of light shine on the remote receiver, remote control operations may not be performed correctly.
Make sure you install the projector in a location free from excessive dust and humidity to prevent the lens or internal components from becoming dirty.
Display Position of Manufacturers Nameplate
The product nameplate is displayed on the top of the projector as shown below. Before installing the mount to the projector, check the numbers on the product nameplate.
Using the Product Safely
4
Rated Voltage 100-240 V
Rating Frequency 50/60 Hz
Rating Current 1.8-0.8 A
Installation Orientation
Check the following points when installing on a wall or a ceiling that is inclined.
Do not face the power inlet upward
Correct (power inlet fac-
ing down)
Incorrect (power inlet facing up)
Do not turn the power supply sideways
Incorrect (power supply facing sideways)
Contents
5
Using the Product Safely
Safety Instructions .................... 1
Safety Indications .......................1
General Information Indications............. 1
Precautions on Installing the Projector........1
Warnings and Cautions on the Installation
Locations ............................. 3
Display Position of Manufacturers Nameplate . . . 3
Installation Orientation ...................4
Preparing the Projector
Package Contents . . ................... 6
Connectable Devices and Necessary
Cables ............................... 7
Projection Distance Table .............. 8
16:10 projected image ....................9
4:3 projected image..................... 10
16:9 projected image ....................11
Installation Procedure
Preparing the Projector .............. 12
Attaching the Projector Mount to the
Projector ............................ 13
Attaching the Ceiling Mount to a
Ceiling or a Wall ..................... 15
Installing the Safety Wire ............. 16
Combining the Projector Mount with
the Ceiling Mount .................... 17
Connecting Cables ................... 18
Adjusting the Orientation of the
Projector ............................ 19
Attaching the Covers ................. 20
Attaching the Power Adapter Cover .........20
Attaching the Mount Cover................ 20
Appendix
Specification . . . . . ................... 21
Appearance........................... 21
Assembly Dimensions ...................22
Preparing the Projector
6
Package Contents
Check that you have all of the following accessories before you start work.
Projector mount (*1) Ceiling mount (*1) Mount cover (*2)
Safety wire
(500 mm)
Wire hook mount
Shape Name
Quan-
tity
Application
M4 x 12 mm cross recessed head screw (with washer)
4 Secures the projector mount to the projector.
(4) Combines and secures a projector mount and
a ceiling mount.
*1 The projector mount and the ceiling mount are combined and secured by these screws temporarily at the time of purchase. Unscrew them before installing.
M3 x 6 mm cross recessed head screw (2) Secures the mount cover.
*2 The mount cover is secured by these screws temporarily at the time of purchase. Unscrew them before installing.
Make sure you use the bolts or screws supplied with this product to install mounts.
Gather the tools and parts you need before you begin installation.
Loading...
+ 16 hidden pages