Epson HC5030UB User Manual

®
PowerLite
Home Cinema
5030UB/5030UBe User's Guide

Contents

PowerLite Home Cinema 5030UB/5030UBe User's Guide ....................................................................... 9
Introduction to Your Projector ................................................................................................................. 10
Setting Up the Projector ........................................................................................................................... 23
Projector Features.............................................................................................................................. 10
Additional Components ................................................................................................................ 12
Optional Equipment and Replacement Parts................................................................................. 12
Warranty and Registration Information.......................................................................................... 13
Notations Used in the Documentation................................................................................................ 14
Where to Go for Additional Information .............................................................................................. 14
Projector Part Locations..................................................................................................................... 14
Projector Parts - Front/Top............................................................................................................ 15
Projector Parts - Rear.................................................................................................................... 16
Projector Parts - Base.................................................................................................................... 17
Projector Parts - Control Panel...................................................................................................... 18
Projector Parts - Remote Control................................................................................................... 20
Projector Placement........................................................................................................................... 23
Projector Setup and Installation Options ....................................................................................... 23
Projection Distance........................................................................................................................ 25
Projector Connections........................................................................................................................ 27
Connecting to Video Sources........................................................................................................ 28
Connecting to an HDMI Video Source ...................................................................................... 28
Attaching and Removing the Cable Clips.................................................................................. 29
Connecting to an MHL-Compatible Device............................................................................... 29
Connecting to a Component Video Source............................................................................... 30
Connecting to a Composite Video Source ................................................................................ 31
Connecting to Computer Sources.................................................................................................. 31
Connecting to a Computer for VGA Video................................................................................. 31
Connecting to a Computer for HDMI Video............................................................................... 32
Connecting to External Speakers.................................................................................................. 32
3
Installing Batteries in the Remote Control .......................................................................................... 33
Using Basic Projector Features ............................................................................................................... 36
Turning On the Projector.................................................................................................................... 36
Turning Off the Projector.................................................................................................................... 38
Viewing 3D Images ............................................................................................................................ 39
Pairing the 3D Glasses with the Projector...................................................................................... 40
Charging the 3D Glasses............................................................................................................... 41
3D Viewing Range......................................................................................................................... 42
Selecting the Language for the Projector Menus................................................................................ 43
Adjusting the Image Height ................................................................................................................ 44
Adjusting the Image Position Using Lens Shift .............................................................................. 45
Image Shape...................................................................................................................................... 47
Correcting Image Shape with the Keystone Buttons...................................................................... 47
Resizing the Image With the Zoom Ring ............................................................................................ 48
Focusing the Image Using the Focus Ring......................................................................................... 49
Adjusting the Color Convergence (Panel Alignment) ......................................................................... 50
Remote Control Operation ................................................................................................................. 52
Selecting an Image Source ................................................................................................................ 54
Projection Modes ............................................................................................................................... 55
Changing the Projection Mode Using the Menus........................................................................... 56
Image Aspect Ratio............................................................................................................................ 57
Changing the Image Aspect Ratio................................................................................................. 57
Available Image Aspect Ratios...................................................................................................... 57
Color Mode......................................................................................................................................... 58
Changing the Color Mode.............................................................................................................. 59
Available Color Modes................................................................................................................... 59
Turning On Auto Iris....................................................................................................................... 60
Using Picture in Picture...................................................................................................................... 61
Available Picture in Picture Options............................................................................................... 61
Adjusting Projector Features................................................................................................................... 63
Shutting Off the Picture Temporarily .................................................................................................. 63
Projector Security Features................................................................................................................ 63
Locking the Projector's Buttons ..................................................................................................... 64
4
Unlocking the Projector's Buttons............................................................................................. 65
Installing a Security Cable............................................................................................................. 65
Saving Settings to Memory and Using Saved Settings ...................................................................... 65
Using WirelessHD ..................................................................................................................................... 67
WirelessHD Transmitter Placement................................................................................................... 67
Connecting the WirelessHD Transmitter............................................................................................ 67
Viewing WirelessHD Content............................................................................................................. 68
Switching WirelessHD Sources.......................................................................................................... 69
Using the WirelessHD Picture-in-Picture Feature .............................................................................. 70
Adjusting the Menu Settings.................................................................................................................... 72
Using the Projector's Menus............................................................................................................... 72
Image Quality Settings - Image Menu ................................................................................................ 73
Input Signal Settings - Signal Menu.................................................................................................... 76
Projector Feature Settings - Settings Menu........................................................................................ 80
Projector Setup Settings - Extended Menu......................................................................................... 83
Projector Memory Options - Memory Menu........................................................................................ 86
Projector Information Display - Info Menu .......................................................................................... 87
Projector Reset Options - Reset Menu............................................................................................... 89
Maintaining and Transporting the Projector........................................................................................... 91
Projector Maintenance....................................................................................................................... 91
Cleaning the Lens.......................................................................................................................... 91
Cleaning the 3D Glasses............................................................................................................... 92
Cleaning the Projector Case.......................................................................................................... 93
Air Filter and Vent Maintenance .................................................................................................... 93
Cleaning the Air Filter................................................................................................................ 94
Replacing the Air Filter.............................................................................................................. 96
Projector Lamp Maintenance......................................................................................................... 98
Replacing the Lamp.................................................................................................................. 98
Resetting the Lamp Timer....................................................................................................... 103
Replacing the Remote Control Batteries ..................................................................................... 104
Transporting the Projector................................................................................................................ 106
5
Solving Problems.................................................................................................................................... 107
Projection Problem Tips................................................................................................................... 107
Projector Light Status....................................................................................................................... 107
Solving Image Problems .................................................................................................................. 111
Solutions When No Image Appears............................................................................................. 111
Solutions When "No Signal" Message Appears........................................................................... 112
Displaying From a PC Laptop................................................................................................. 112
Displaying From a Mac Laptop ............................................................................................... 113
Solutions When "Not Supported" Message Appears................................................................... 113
Solutions When Only a Partial Image Appears............................................................................ 113
Solutions When the Image is Not Rectangular ............................................................................ 114
Solutions When the Image Contains Noise or Static ................................................................... 114
Solutions When the Image is Fuzzy or Blurry.............................................................................. 115
Solutions When the Image Brightness or Colors are Incorrect .................................................... 115
Solutions When a 3D Image Does Not Display Correctly ............................................................ 116
Solutions When a WirelessHD Source Does Not Display Correctly............................................. 117
Solving Projector or Remote Control Operation Problems ............................................................... 118
Solutions to Projector Power or Shut-Off Problems..................................................................... 118
Solutions to Problems with the Remote Control........................................................................... 119
Where to Get Help............................................................................................................................ 119
Technical Specifications ........................................................................................................................ 121
General Projector Specifications...................................................................................................... 121
Projector Lamp Specifications.......................................................................................................... 122
Remote Control Specifications......................................................................................................... 123
Projector Dimension Specifications.................................................................................................. 123
Projector Electrical Specifications.................................................................................................... 123
Projector Environmental Specifications............................................................................................ 124
Projector Safety and Approvals Specifications................................................................................. 124
Supported Video Display Formats.................................................................................................... 124
Notices ..................................................................................................................................................... 128
Recycling.......................................................................................................................................... 128
Important Safety Information............................................................................................................ 128
Important Safety Instructions............................................................................................................ 129
6
3D Safety Instructions ................................................................................................................. 131
Restriction of Use........................................................................................................................ 133
FCC Compliance Statement............................................................................................................. 133
Trademarks...................................................................................................................................... 134
Open Source Software License........................................................................................................ 134
Copyright Notice............................................................................................................................... 179
A Note Concerning Responsible Use of Copyrighted Materials................................................... 180
Copyright Attribution.................................................................................................................... 180
7
PowerLite Home Cinema 5030UB/5030UBe User's Guide
Welcome to the PowerLite Home Cinema 5030UB/5030UBe User's Guide.
9

Introduction to Your Projector

Refer to these sections to learn more about your projector and this manual.
Projector Features Notations Used in the Documentation Where to Go for Additional Information Projector Part Locations

Projector Features

The PowerLite Home Cinema 5030UB and 5030UBe projectors include these special features:
Bright, high-resolution projection system
• Up to 2400 lumens of color brightness (color light output) and 2400 lumens of white brightness (white light output)
Note: Color brightness (color light output) and white brightness (white light output) will vary depending on usage conditions. Color light output measured in accordance with IDMS 15.4; white light output measured in accordance with ISO 21118.
• 1080p native resolution
• Images up to 300 inches (7.62 m) for projection on any wall or screen
• Fujinon lens for uniformity
Full 3D projection
• Active 3D projection with RF active shutter glasses
• Supports side-by-side, top-and-bottom, and frame packing 3D formats
Flexible connectivity
• Two HDMI ports for video device or computer connections
• One MHL (Mobile High-definition Link)-compatible HDMI port on the WirelessHD Transmitter for high­quality audio and video from tablets and smartphones (PowerLite Home Cinema 5030UBe)
Easy-to-use setup and operation features
• Vertical and horizontal lens shift dials, and vertical keystone correction buttons for flexible projector placement
10
• 2.1× optical zoom ratio for improved zooming capability
Product Box Contents Additional Components Optional Equipment and Replacement Parts Warranty and Registration Information
Parent topic: Introduction to Your Projector

Product Box Contents

Save all the packaging in case you need to ship the projector. Always use the original packaging (or equivalent) when shipping.
Make sure your projector box included all of these parts:
1 Projector 2 Remote control 3 Remote control batteries (two AA alkaline) 4 Power cord
11
5 Projector documentation CD 6 3D glasses (2 pairs) 7 WirelessHD Transmitter (PowerLite Home Cinema 5030UBe) 8 WirelessHD Transmitter AC adapter (PowerLite Home Cinema 5030UBe)
Parent topic: Projector Features

Additional Components

Depending on how you plan to use the projector, you may need to obtain the following additional components:
• To receive a component video signal, you need a compatible component cable. You can purchase one from Epson or an authorized Epson reseller.
• To receive an HDMI signal, you need a compatible HDMI cable. You can purchase one from Epson or an authorized Epson reseller.
Note: To connect a Mac that includes only a Mini DisplayPort, Thunderbolt port, or Mini-DVI port for video output, you need to obtain an adapter that allows you to connect to the projector's HDMI port. Contact Apple for compatible adapter options.
• To receive an HDMI signal via MHL, you need an MHL-compatible device, an MHL cable or an HDMI cable and an MHL adapter compatible with your device. Devices with an integrated MHL connector may not require a cable (PowerLite Home Cinema 5030UBe).
• To receive and view a 3D signal, you need a compatible HDMI cable. You can purchase one from Epson or an authorized Epson reseller. If your video source is a 3D Blu-ray disc, you also need a Blu­ray player that supports 3D playback. See your local computer or electronics dealer for purchase information.
Parent topic: Projector Features Related references

Optional Equipment and Replacement Parts

Optional Equipment and Replacement Parts
You can purchase screens, other optional accessories, and replacement parts from an Epson authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766). Or you can purchase online at epsonstore.com (U.S. sales) or epson.ca (Canadian sales).
12
Epson offers the following optional accessories and replacement parts for your projector:
Option or part Part number
Genuine Epson replacement lamp (ELPLP69) V13H010L69 Replacement air filter V13H134A39 RF 3D glasses (ELPGS03) V12H548006 Projector ceiling mount CHF1000 Belkin PureAV HDMI audio video cable, 6 ft AV22300-06 Belkin PureAV HDMI audio video cable, 12 ft AV22300-12 Belkin PureAV HDMI audio video cable, 3 ft AV22300-03 Belkin Pro Series VGA/SVGA cable, 6 ft F3H982-06 Belkin Pro Series VGA/SVGA cable, 10 ft F3H982-10 Belkin Pro Series VGA/SVGA cable, 25 ft F3H982-25 Kensington security lock ELPSL01 Remote control 1598522
In addition to the accessories listed above, 1-year and 2-year extended service plans are available.
Parent topic: Projector Features

Warranty and Registration Information

Your projector comes with a basic warranty that lets you project with confidence. For details, see the warranty brochure that came with your projector.
In addition, Epson offers free Extra Care Home Service. In the unlikely event of an equipment failure, you won’t have to wait for your unit to be repaired. Instead, Epson will ship you a replacement unit anywhere in the United States, Canada, or Puerto Rico. See the Extra Care Home Service brochure for details.
Register your product online using the projector CD or at this site: epson.com/webreg Registering also lets you receive special updates on new accessories, products, and services.
Parent topic: Projector Features
13

Notations Used in the Documentation

Follow the guidelines in these notations as you read your documentation:
Warnings must be followed carefully to avoid bodily injury.
Cautions must be observed to avoid damage to your equipment.
Notes contain important information about your projector.
Tips contain additional projection information.
Parent topic: Introduction to Your Projector

Where to Go for Additional Information

Need quick help on using your projector? Here's where to look for help:
epson.com/support (U.S) or epson.ca/support (Canada) View FAQs (frequently asked questions) and e-mail your questions to Epson technical support 24
hours a day.
• If you still need help after checking this manual and the sources listed above, you can use the Epson PrivateLine Support service to get help fast. For details, see "Where to Get Help".
Parent topic: Introduction to Your Projector Related references
Where to Get Help

Projector Part Locations

Check the projector part illustrations to learn about the parts on your projector.
Projector Parts - Front/Top Projector Parts - Rear Projector Parts - Base Projector Parts - Control Panel Projector Parts - Remote Control
Parent topic: Introduction to Your Projector
14

Projector Parts - Front/Top

1 Lamp cover 2 Horizontal and vertical lens shift dials 3 Exhaust vent 4 Remote receiver 5 Lens shutter 6 Lens 7 Air intake/air filter cover 8 Front adjustable foot 9 Control panel and lights 10 Focus ring 11 Zoom ring
Parent topic: Projector Part Locations
15

Projector Parts - Rear

1 Cable clip holes 2 HDMI1 port 3 HDMI2 port 4 Component ports 5 Video port 6 PC port (VGA) 7 RS-232C port 8 Trigger out port 9 Service port 10 Remote receiver 11 AC input port
Parent topic: Projector Part Locations Related tasks
Installing a Security Cable Attaching and Removing the Cable Clips
16

Projector Parts - Base

1 Front adjustable feet 2 Mounting bracket holes 3 Cable cover attachment point 4 Air exhaust vent
Caution: The air exhaust vent cools the WirelessHD receiver. If you mount the projector on the ceiling, make sure dust does not block the vent or the WirelessHD receiver can overheat.
Parent topic: Projector Part Locations
17

Projector Parts - Control Panel

1 Status light 2 Lamp light 3 Temp light 4 Menu button (accesses projector menu system) 5 Control panel cover
18
6 Vertical keystone adjustment buttons (adjust screen shape) and arrow buttons 7 Arrow buttons 8 Esc button (cancels/exits functions) 9 Enter button (selects options) 10 Source button (cycles through the list of sources) 11 Power button/light
Parent topic: Projector Part Locations Related references
Projector Light Status
19

Projector Parts - Remote Control

1 On button (turns on projector) 2 P-in-P button (controls the Picture-in-Picture mode for HDMI inputs) 3 Source buttons (select specific video input sources)
20
4 HDMI Link button (displays the settings menu for HDMI Link)
Link Menu button (displays the main menu of the connected device)
Control buttons (control playback and other features of connected devices that support the HDMI
CEC standard) 5 2D/3D button (cycles between 2D and 3D modes) 6 Arrow buttons (move though on-screen options) 7 Default button (returns selected setting to default value) 8 Menu button (accesses projector menu system) 9 Auto Iris button (optimizes the image based on brightness of content) 10 User button (customizable for different functions) 11 Memory button (accesses the Memory menu) 12 WirelessHD transmitter control buttons (PowerLite Home Cinema 5030UBe) 13 Pattern button (displays a test pattern) 14 3D Format button (changes the 3D format) 15 Frame Int button (adjusts the Frame Interpolation setting) 16 Aspect button (selects the image aspect ratio) 17 RGBCMY button (adjusts hue, saturation, and brightness for each RGBCMY color) 18 Esc button (cancels/exits functions) 19 Enter button (selects options) 20 Super Res button (reduces blurring around the edges of images when viewing 3D content) 21 Color Mode button (selects display modes) 22 Volume up/down buttons (adjust volume for devices connected via HDMI Link) 23 Blank button (turns off video projection) 24 Illumination button (lights the remote control) 25 Standby button (turns off the projector)
Parent topic: Projector Part Locations Related references
Remote Control Operation
21
Projector Memory Options - Memory Menu
22

Setting Up the Projector

Follow the instructions in these sections to set up your projector for use.
Projector Placement Projector Connections Installing Batteries in the Remote Control

Projector Placement

You can place the projector on almost any flat surface to project an image. You can also install the projector in a ceiling mount if you want to use it in a fixed location. Keep these considerations in mind as you select a projector location:
• Place the projector on a sturdy, level surface or install it using a compatible mount.
• Leave plenty of space around and under the projector for ventilation, and do not place it on top of or next to anything that could block the vents.
• Position the projector within reach of a grounded electrical outlet or extension cord.
Projector Setup and Installation Options Projection Distance
Parent topic: Setting Up the Projector Related tasks
Changing the Projection Mode Using the Menus

Projector Setup and Installation Options

You can set up or install your projector in the following ways: Front
23
Rear
Front Ceiling
Rear Ceiling
24
Wherever you set up the projector, make sure to position it squarely in front of the center of the screen, not at an angle, if possible.
If you project from the ceiling or from the rear, be sure to select the correct Projection option in the projector's menu system.
Parent topic: Projector Placement Related references
Projector Feature Settings - Settings Menu

Projection Distance

The distance at which you place the projector from the screen determines the approximate size of the image. The image size increases the farther the projector is from the screen, but can vary depending on the zoom factor, aspect ratio, and other settings.
Use the tables here to determine approximately how far to place the projector from the screen based on the size of the projected image. (Conversion figures may have been rounded up or down.)
4:3 Aspect Ratio Image or Screen
25
Screen or image size Projection distance (1) Offset from lens center Offset from lens center
Wide to Tele
(2) (3)
40 inches (101.6 cm) 57 to 121.7 inches 11 inches (28 cm) 35.0 inches (89 cm)
(144 to 309 cm)
60 inches (152.4 cm) 85.8 to 183.5 inches 16.5 inches (42 cm) 52.4 inches (133 cm)
(218 to 466 cm)
80 inches (203.2 cm) 115 to 245.3 inches 22 inches (56 cm) 70.1 inches (178 cm)
(292 to 623 cm)
100 inches (254 cm) 144.1to306.7inches 27.6 inches (70 cm) 87.4 inches (222 cm)
(366 to 779 cm)
120 inches (304.8 cm) 173.2 to 368.5 inches 33.1 inches (84 cm) 105.1 inches (267 cm)
(440 to 936 cm)
150 inches (381 cm) 216.9to461.0inches 41.3 inches (105 cm) 131.1 inches (333 cm)
(551 to 1171 cm)
180 inches (457.2 cm) 289.8 to 615 inches 54.7 inches (139 cm) 174.8 inches (444 cm)
(736 to 1562 cm)
16:9 Aspect Ratio Image or Screen
Screen or image size Projection distance (1) Offset from lens center Offset from lens center
Wide to Tele
(2) (3)
40 inches (101.6 cm) 46.1 to 94.2 inches 9.1 inches (23 cm) 28.7inches(73cm)
(117 to 252 cm)
60 inches (152.4 cm) 69.7 to 149.6 inches 13.4 inches (34 cm) 42.9 inches (109 cm)
(177 to 380 cm)
80 inches (203.2 cm) 93.7 to 200 inches 18.1 inches (46 cm) 57.1 inches (145 cm)
(238 to 508 cm)
26
Screen or image size Projection distance (1) Offset from lens center Offset from lens center
100 inches (254 cm) 117.3to250.4inches 22.4 inches (57 cm) 71.3 inches (181 cm)
120 inches (304.8 cm) 141.3 to 300.8 inches 26.8 inches (68 cm) 85.8 inches (218 cm)
150 inches (381 cm) 177.2to376.4inches 33.5 inches (85 cm) 107.1 inches (272 cm)
180 inches (457.2 cm) 212.6 to 452 inches 40.6 inches (103 cm) 128.7 inches (327 cm)
Parent topic: Projector Placement

Projector Connections

You can connect the projector to a variety of computer, video, and audio sources to display presentations, movies, or other images, with or without sound.
• For video projection, connect devices such as DVD players, gaming consoles, streaming devices, digital cameras, smartphones, and tablets with compatible video output ports.
Wide to Tele
(298 to 636 cm)
(359 to 764 cm)
(450 to 956 cm)
(540 to 1148 cm)
(2) (3)
Note: To connect a smartphone or tablet, you may need to obtain an adapter that allows you to
connect to the projector. This allows you to mirror your smartphone or tablet screens, watch movies, and more. Contact your device manufacturer for compatible adapter options.
• Connect any type of computer (Windows or Mac) that has a standard video output (15-pin VGA monitor) port, or HDMI port.
Caution: If you will use the projector at altitudes above 4921 feet (1500 m), turn on High Altitude Mode to ensure the projector's internal temperature is regulated properly.
Connecting to Video Sources Connecting to Computer Sources Connecting to External Speakers
Parent topic: Setting Up the Projector
27
Related references
Projector Setup Settings - Extended Menu

Connecting to Video Sources

Follow the instructions in these sections to connect video devices to the projector.
Connecting to an HDMI Video Source Attaching and Removing the Cable Clips Connecting to an MHL-Compatible Device Connecting to a Component Video Source Connecting to a Composite Video Source
Parent topic: Projector Connections
Connecting to an HDMI Video Source
If your video source has an HDMI port, you can connect it to the projector using an optional HDMI cable. The HDMI connection provides the best image quality.
1. Connect the HDMI cable to your video source's HDMI output port.
2. Connect the other end to one of the projector's HDMI ports.
Note: If you connected a game console, it may take a few seconds for your image to appear when you switch to the game console's input source. To reduce the potential lag in response time to game commands, set your game console's output format to a progressive signal of 480p or 720p. See your game console documentation for instructions.
You can also select the Fast Image Processing setting to reduce lag time.
28
Note: When an audio/video source that meets the HDMI CEC standard is connected to the projector's
HDMI port, you can use the projector's remote control to control certain features of the linked device by pressing the HDMI Link button on the remote control and setting HDMI Link to On.
Parent topic: Connecting to Video Sources Related references
Input Signal Settings - Signal Menu
Related tasks
Attaching and Removing the Cable Clips
Attaching and Removing the Cable Clips
You can install the cable clips that came with your projector to provide additional support to the power and HDMI cables.
1. Plug in the power and HDMI cables.
2. Insert each guide into the cable clip holes near the power inlet and HDMI port.
3. Attach the cable clips to the power and HDMI cables. Be sure to leave the clamps unlocked.
4. Slide each cable clip onto the guides and lock the clamps onto the connectors.
To remove the cable clips, open the clamps and disconnect the cables. Then pinch the sides of each guide and carefully pull them out of the cable clip holes.
Parent topic: Connecting to Video Sources
Connecting to an MHL-Compatible Device
If you have an MHL-compatible smartphone or tablet, you can connect it to the WirelessHD Transmitter using either an MHL cable or an HDMI cable with a device-compatible MHL adapter (PowerLite Home Cinema 5030UBe only). If you have a device with a built-in MHL connector, plug it directly into the HDMI
5 / MHL (IN) port. Note: Some connected devices may not charge when using an MHL adapter.
29
1. Connect the MHL cable or adapter to your device's Micro-USB port.
2. If you are using an MHL adapter, connect it to an MHL-compatible HDMI cable.
3. Connect the other end of the cable to the WirelessHD Transmitter's HDMI 5 / MHL (IN) port.
Parent topic: Connecting to Video Sources
Connecting to a Component Video Source
If your video source has component video ports, you can connect it to the projector using an optional component video cable. Depending on your component ports, you may need to use an adapter cable along with a component video cable.
1. Connect the component connectors to your video source's color-coded component video output
ports, usually labeled Y, Pb, Pr or Y, Cb, Cr. If you are using an adapter, connect these connectors to your component video cable.
2. Connect the other end to the projector's color-coded Component video input ports.
If your image colors appear incorrect, you may need to change the Input Signal setting in the projector's Extended menu.
Note: If you connected a game console, it may take a few seconds for your image to appear when you switch to the game console's input source. To reduce the potential lag in response time to game commands, set your game console's output format to a progressive signal of 480p or 720p. See your game console documentation for instructions.
30
You can also select the Fast Image Processing setting to reduce lag time. Parent topic: Connecting to Video Sources Related references
Input Signal Settings - Signal Menu
Connecting to a Composite Video Source
If your video source has a composite video port, you can connect it to the projector using an optional RCA-style video or A/V cable.
1. Connect the cable with the yellow connector to your video source's yellow video output port.
2. Connect the other end to the projector's Video port.
Parent topic: Connecting to Video Sources

Connecting to Computer Sources

Follow the instructions in these sections to connect a computer to the projector.
Connecting to a Computer for VGA Video Connecting to a Computer for HDMI Video
Parent topic: Projector Connections
Connecting to a Computer for VGA Video
You can connect the projector to your computer using a VGA computer cable. Note: To connect a Mac that includes only a Mini DisplayPort, Thunderbolt port, or Mini-DVI port for
video output, you need to obtain an adapter that allows you to connect to the projector's VGA video port. Contact Apple for compatible adapter options.
1. If necessary, disconnect your computer's monitor cable.
31
2. Connect the VGA computer cable to your computer's monitor port.
3. Connect the other end to a PC port on the projector.
4. Tighten the screws on the VGA connector.
Parent topic: Connecting to Computer Sources
Connecting to a Computer for HDMI Video
If your computer has an HDMI port, you can connect it to the projector using an optional HDMI cable. Note: To connect a Mac that includes only a Mini DisplayPort, Thunderbolt port, or Mini-DVI port for
video output, you need to obtain an adapter that allows you to connect to the projector's HDMI port.
1. Connect the HDMI cable to your computer's HDMI output port.
2. Connect the other end to one of the projector's HDMI ports.
Parent topic: Connecting to Computer Sources Related tasks
Attaching and Removing the Cable Clips

Connecting to External Speakers

To add sound, you can connect your video source and speakers to an audio video receiver, then connect the receiver to the projector using one of the receiver's compatible video outputs (an HDMI connection provides the best image quality, if available). You can also connect speakers to any video source that has its own speaker connections.
32
1 Video source 2 Surround sound 3 Receiver 4 Video cable
Parent topic: Projector Connections

Installing Batteries in the Remote Control

The remote control uses the two AA batteries that came with the projector. Caution: Use only the type of batteries specified in this manual. Do not install batteries of different types,
or mix new and old batteries.
33
1. Open the battery cover.
2. Insert the batteries with the + and – ends facing as shown.
34
3. Close the battery cover and press it down until it clicks into place.
Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed.
Parent topic: Setting Up the Projector Related references
Remote Control Specifications
35

Using Basic Projector Features

Follow the instructions in these sections to use your projector's basic features.
Turning On the Projector Turning Off the Projector Viewing 3D Images Selecting the Language for the Projector Menus Adjusting the Image Height Image Shape Resizing the Image With the Zoom Ring Focusing the Image Using the Focus Ring Adjusting the Color Convergence (Panel Alignment) Remote Control Operation Selecting an Image Source Projection Modes Image Aspect Ratio Color Mode Using Picture in Picture

Turning On the Projector

Turn on the computer or video equipment you want to use before you turn on the projector so it can display the image source.
36
1. Connect the power cord to the projector's power inlet.
2. Plug the power cord into an electrical outlet.
Note: With Direct Power On turned on, the projector turns on as soon as you plug it in.
3. Press the power button on the projector or the On button on the remote control to turn on the
projector. The shutter opens and the Status light flashes blue as the projector warms up. Once the projector is
warmed up, the Status light stops flashing and turns blue. Warning: Never look into the projector lens when the lamp is on. This can damage your eyes and is
especially dangerous for children.
If you do not see a projected image right away, try the following:
• Turn on the connected computer or video device.
• Insert a DVD or other video media and press the play button, if necessary.
• Press the Source button on the projector to detect the video source, or press a source button on the remote control.
Parent topic: Using Basic Projector Features Related references
Projector Setup Settings - Extended Menu
37

Turning Off the Projector

Before turning off the projector, shut down any computer connected to it so you can see the computer display during shutdown.
Note: Turn off this product when not in use to prolong the life of the projector. Lamp life will vary depending upon mode selected, environmental conditions, and usage. Brightness decreases over time.
Note: When using the Blank feature, the projector lamp is still on. To turn off the lamp, turn off the projector.
1. Press the power button on the projector or the Standby button on the remote control.
The projector displays a shutdown confirmation screen.
2. Press the power button on the projector or the Standby button on the remote control again. (To
leave it on, press any other button.) The shutter closes, the lamp turns off, and the Status light turns off.
3. To transport or store the projector, make sure the Status light is off, then unplug the power cord.
38
Caution: To avoid damaging the projector or lamp, never unplug the power cord when the Status
light is on or flashing.
Parent topic: Using Basic Projector Features Related tasks
Shutting Off the Picture Temporarily Transporting the Projector

Viewing 3D Images

You can view 3D images using your projector. Viewing 3D images requires a 3D-compatible video device and a pair of Epson RF 3D glasses.
You can purchase Epson RF 3D glasses from an Epson authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766). Or you can purchase online at epsonstore.com (U.S. sales) or
epson.ca (Canadian sales).
1. Connect a 3D-compatible video device to the projector using a compatible HDMI cable.
2. Turn on the video device, then turn on the projector.
3. Begin playback from the video device.
Note: Make sure you set the video device to play content in 3D mode.
4. Press the 2D/3D button on the remote control to activate 3D mode, if necessary.
39
5. Slide the power switch on the 3D glasses to the On position.
6. Put on the 3D glasses. If you do not see a 3D image, pair the glasses with the projector.
Note: If you change the video source or you are not within range of your projector, the glasses enter standby mode and the indicator light flashes green. Slide the power switch on the glasses to the Off position and then back to the On position to resume 3D viewing.
Pairing the 3D Glasses with the Projector Charging the 3D Glasses 3D Viewing Range
Parent topic: Using Basic Projector Features Related tasks
Connecting to an HDMI Video Source Connecting to a Computer for HDMI Video

Pairing the 3D Glasses with the Projector

Pair the glasses with the projector to establish communication between them for 3D viewing.
1. Turn on the projector.
2. Set the image source to HDMI.
3. Project a 3D image.
40
4. Slide the power switch on the 3D glasses to the On position.
5. Move the glasses within 10 feet (3 m) of the projector, then hold down the Pairing button on the
glasses for at least three seconds.
The status light on the glasses flashes green and red. If pairing is successful, the light turns green for 10 seconds and then turns off.
Parent topic: Viewing 3D Images

Charging the 3D Glasses

Charge the glasses when the status light on the glasses flashes red to indicate a low battery.
41
1. Connect the smaller end of the charging cable to the port on the bridge of the glasses.
Note: Make sure you connect the cable in the correct orientation or you may damage the glasses or cable.
2. Do one of the following:
• Plug the other end of the charging cable into a powered USB port on a computer or other device.
• Plug the other end of the charging cable into a USB-to-AC adapter with the following specifications:
Input: 100-240V, ~0.15A, 50-60Hz Output: 5V=1A
The glasses are fully charged when the status light on the glasses stays green.
Parent topic: Viewing 3D Images

3D Viewing Range

When you view 3D images, make sure you are positioned within the viewing range shown here.
42
1 32 ft (10 m)
Parent topic: Viewing 3D Images

Selecting the Language for the Projector Menus

If you want to view the projector's menus and messages in another language, you can change the Language setting.
1. Turn on the projector.
2. Press the Menu button.
43
3. Select the Extended menu and press Enter.
4. Select the Language setting and press Enter.
5. Select the language you want to use and press Enter.
6. Press Menu or Esc to exit the menus.
Parent topic: Using Basic Projector Features

Adjusting the Image Height

If you are projecting from a table or other flat surface, and the image is too high or low, you can adjust the image height using the projector's adjustable feet.
1. Turn on the projector and display an image.
2. If the image is tilted, rotate the front feet to adjust their height.
3. Use the vertical and horizontal lens shift dials on the projector to adjust the position of the projected image as necessary.
44
If the projected image is unevenly rectangular, you need to adjust the image shape.

Adjusting the Image Position Using Lens Shift

Parent topic: Using Basic Projector Features Related concepts
Image Shape
Adjusting the Image Position Using Lens Shift
If you cannot install the projector directly in front of the screen, you can adjust the position of the projected image using the lens shift feature.
Note: Wait 30 minutes after turning on the projector before setting the focus, zoom, and lens shift for maximum accuracy.
1. Turn on the projector and display an image.
2. Turn the vertical and horizontal lens shift dials on the projector to adjust the position of the projected image as necessary.
Note: You cannot move the image to both the horizontal and vertical maximum values.
45
1 Horizontal height × 47% 2 Vertical height × 96%
Follow these guidelines when using lens shift to adjust your images:
• When adjusting the image height, position the image lower than where you want it to be and then
move it up using the vertical lens shift dial. This will help prevent the image from moving down after adjustment.
• Keeping the vertical and horizontal lens shift dials in their center positions produces the clearest
picture.
Parent topic: Adjusting the Image Height
46

Image Shape

You can project an evenly rectangular image by placing the projector directly in front of the center of the screen and keeping it level. If you place the projector at an angle to the screen, or tilted up or down, or off to the side, you may need to correct the image shape for the best display quality.

Correcting Image Shape with the Keystone Buttons

Parent topic: Using Basic Projector Features
Correcting Image Shape with the Keystone Buttons
You can use the projector's keystone correction buttons to correct the shape of an image that is unevenly rectangular on the sides.
Note: To provide the best possible image quality, adjust the projector's position to correct the image shape. If this isn't possible, use the keystone correction buttons on the projector to correct the image shape.
1. Turn on the projector and display an image.
Note: You can display a pattern to aid in adjusting the projected image using the Settings menu. Note: You can also display the pattern by pressing the Pattern button on the remote control.
2. Press one of these keystone buttons on the control panel to display the Keystone adjustment screen.
47
3. Press a keystone button on the projector's control panel to adjust the image shape.
After correction, your image is slightly smaller. Note: If the projector is installed out of reach, you can also correct the image shape with the remote
control using the Keystone settings in the projector menus.
Parent topic: Image Shape Related references
Projector Feature Settings - Settings Menu

Resizing the Image With the Zoom Ring

1. Turn on the projector and display an image. Wait 30 minutes after turning on the projector before setting the focus, zoom, and lens shift for maximum accuracy.
Note: You can display a pattern to aid in adjusting the projected image using the Pattern button on the remote control.
48
2. To enlarge or reduce the image size, rotate the projector's zoom ring.
Parent topic: Using Basic Projector Features

Focusing the Image Using the Focus Ring

1. Turn on the projector and display an image. Wait 30 minutes after turning on the projector before setting the focus, zoom, and lens shift for maximum accuracy.
Note: You can display a pattern to aid in adjusting the projected image using the Pattern button on the remote control.
2. To sharpen the image focus, rotate the projector’s focus ring.
49
Parent topic: Using Basic Projector Features

Adjusting the Color Convergence (Panel Alignment)

You can use the Panel Alignment feature to manually adjust the color convergence (the alignment of the red, green and blue colors) in the projected image.
Note: Allow your projector to warm up for at least 10 to 15 minutes and make sure the image is in focus before you use the Panel Alignment feature. The projected image should be a minimum of 60 inches (152 cm) diagonally and the projection surface should not be colored or textured, otherwise the adjustment grids will be difficult to align.
1. Turn on the projector.
2. Press the Menu button.
3. Select the Extended menu and press Enter.
4. Select the Panel Alignment setting and press Enter.
5. Select the Panel Alignment setting and press Enter.
6. Select On and press Enter.
7. Select the Select Color setting and choose one of the following:
R to adjust the red color convergence.
50
B to adjust the blue color convergence. Note: You can only adjust the red or blue color convergence. Green is the standard color panel and
cannot be adjusted.
8. Select the Pattern Color setting and press Enter.
9. Select the pattern you want to use and press Enter.
10. Select Start Adjustments and press Enter. You see this screen:
11. Use the arrow buttons on the remote control to adjust the color alignment in the corner of the screen highlighted by the orange box.
12. Press the Enter button to move to the next corner of the screen.
13. When you are finished adjusting each corner of the screen, press Enter. You see this screen:
51
14. Do one of the following:
• If your projector's panel alignment is now correct, select Exit and press Enter to return to the
Panel Alignment menu.
• If your projector needs additional panel alignment, select Select intersection and adjust and
press Enter. Use the arrow keys on the remote control to highlight the corner of any box on the screen that is misaligned and press Enter to adjust the color convergence. Repeat this step as necessary.
Parent topic: Using Basic Projector Features

Remote Control Operation

The remote control lets you control the projector from almost anywhere in the room. You can point it at the screen, or the front or back of the projector.
Make sure that you aim the remote control at the projector's receivers within the distance and angles listed here.
52
Vertical
1 32 feet (10 m) 2 ± 30° 3 60° 4 10°
53
Horizontal
1 32 feet (10 m) 2 ± 30°
Note: Avoid using the remote control in conditions with bright fluorescent lights or in direct sunlight, or the projector may not respond to commands. If you will not use the remote control for a long time, remove the batteries.
Parent topic: Using Basic Projector Features

Selecting an Image Source

If you connected multiple image sources to the projector, such as a computer and DVD player, you may want to switch from one image source to the other.
1. Make sure the connected image source you want to use is turned on.
54
2. For video image sources, insert a DVD or other video media and press its play button, if necessary.
3. Do one of the following:
• Press the Source button on the projector until you see the image from the source you want.
• Press the button for the source you want on the remote control. If there is more than one port for
that source, press the button again to cycle through the sources.
1 HDMIportsources 2 WirelessHDsources(PowerLiteHomeCinema5030UBe) 3 PC port(VGA)source 4 Compositevideosource 5 Componentsource
Parent topic: Using Basic Projector Features

Projection Modes

Depending on how you positioned the projector, you may need to change the projection mode so your images project correctly.
Front (default setting) lets you project from a table in front of the screen.
55
Front/Ceiling flips the image over top-to-bottom to project upside-down from a ceiling or wall mount.
Rear flips the image horizontally to project from behind a translucent screen.
Rear/Ceiling flips the image over top-to-bottom and horizontally to project from the ceiling and behind
a translucent screen.

Changing the Projection Mode Using the Menus

Parent topic: Using Basic Projector Features
Changing the Projection Mode Using the Menus
You can change the projection mode to flip the image over top-to-bottom and/or left-to-right using the projector menus.
1. Turn on the projector and display an image.
2. Press the Menu button.
3. Select the Settings menu and press Enter.
4. Select the Projection setting and press Enter.
5. Select a projection mode and press Enter.
6. Press Menu or Esc to exit the menus.
Parent topic: Projection Modes Related concepts
Projector Placement
56

Image Aspect Ratio

The projector can display images in different width-to-height ratios called aspect ratios. Normally the input signal from your video source determines the image's aspect ratio. However, for certain images you can change the aspect ratio to fit your screen by pressing a button on the remote control.
If you always want to use a particular aspect ratio for a certain video input source, you can select it using the projector's menus.
Changing the Image Aspect Ratio Available Image Aspect Ratios
Parent topic: Using Basic Projector Features

Changing the Image Aspect Ratio

You can change the aspect ratio of the displayed image to resize it. Note: For HDMI sources, the input signal determines the image's aspect ratio.
1. Turn on the projector and switch to the image source you want to use.
2. Press the Aspect button on the remote control.
A list of the available aspect ratios appears.
3. To cycle through the available aspect ratios for your input signal, press the up or down arrow buttons repeatedly. Press Enter to select the highlighted aspect ratio.
Parent topic: Image Aspect Ratio

Available Image Aspect Ratios

You can select the following image aspect ratios, depending on the input signal from your image source.
Note: When the projector is in 3D mode, the aspect ratio is automatically set to Normal.
57
Note: Black bands and cropped images may project in certain aspect ratios, depending on the aspect
ratio and resolution of your input signal.
Aspect ratio setting Description Auto Automatically sets the aspect ratio according to the input signal. Normal Displays images using the full projection area and maintains the
Zoom Displays images using the full width of the projection area and
Full Displays images using the full width of the projection area, but does
Note: The Auto aspect ratio setting is available only for HDMI, component, and WirelessHD image
sources.
Parent topic: Image Aspect Ratio Related references
Input Signal Settings - Signal Menu

Color Mode

aspect ratio of the image.
maintains the aspect ratio of the image.
not maintain the aspect ratio.
The projector offers different Color Modes to provide optimum brightness, contrast, and color for a variety of viewing environments and image types. You can select a mode designed to match your image and environment, or experiment with the available modes.
If you always want to use a particular color mode for a certain video input source, you can select it using the projector menus.
Changing the Color Mode Available Color Modes Turning On Auto Iris
Parent topic: Using Basic Projector Features Related references
Image Quality Settings - Image Menu
58

Changing the Color Mode

You can change the projector's Color Mode using the remote control to optimize the image for your viewing environment.
1. Turn on the projector and switch to the image source you want to use.
2. If you are projecting from a DVD player or other video source, insert a disc or other video media and press the play button, if necessary.
3. Press the Color Mode button on the remote control to change the Color Mode.
A list of available Color Modes appears.
4. To cycle through all the available Color Modes for your input signal, press the up or down arrow buttons repeatedly. Press Enter to select a Color Mode.
Parent topic: Color Mode

Available Color Modes

You can set the projector to use these Color Modes, depending on the input source you are using:
2D Images
Color Mode Description Dynamic Best for projecting in a bright room Natural or THX Best for projecting in a dark room Living Room Best for projecting in a room with closed curtains Cinema Best for movies projected in a dark room B&W Cinema Best for black and white movies projected in a dark room
3D Images
59
Color Mode Description 3D Dynamic Best for projecting in a bright room 3D Cinema Best for movies projected in a dark room 3D THX Best for projecting in a dark room
Parent topic: Color Mode

Turning On Auto Iris

In certain color modes, you can turn on the Auto Iris setting to automatically optimize the image based on the brightness of the content you project.
1. Turn on the projector and switch to the image source you want to use.
2. Press the Menu button. Note: You can also press the Auto Iris button the remote control the access the Auto Iris setting
directly.
3. Select the Image menu and press Enter.
4. Select the Auto Iris setting and choose one of the following:
High Speed to adjust brightness as soon as the scene changes.
60
Normal for standard brightness adjustment. Note: You can set Auto Iris for each Color Mode that supports the feature.
5. Press Menu or Esc to exit the menus.
Parent topic: Color Mode

Using Picture in Picture

You can use the Picture in Picture mode to view two image sources simultaneously. Note: You can only display HDMI or WirelessHD video sources when Picture in Picture mode is active.
1. Turn on the projector and switch to the HDMI or WirelessHD image source you want to use.
2. Press the P-in-P button on the remote control.
The second HDMI video source appears as a sub-screen in the corner of the image. Note: While Picture in Picture mode is active, press the Menu button on the remote control to adjust
the size and position of the sub-screen.
3. To swap the main screen and sub-screen video sources, press and hold the P-in-P button for at least three seconds.
4. Press the P-in-P button again to close the sub-screen and resume normal projection.

Available Picture in Picture Options

Parent topic: Using Basic Projector Features
Available Picture in Picture Options
You can adjust the following options by pressing the Menu button on the remote control while Picture in Picture mode is active:
61
Setting Description Subscreen Size Adjusts the size of the sub-screen Subscreen Position Adjusts the location where the sub-screen is displayed Subscreen Source Selects which source appears in the sub-screen
(PowerLite Home Cinema 5030UBe)
Swap Main/Sub Switches the videosourcedisplayedonthemainscreenwiththe
source displayed on the sub-screen
Exit Picture in Picture Closes the sub-screen and resumes normal projection
Parent topic: Using Picture in Picture
62

Adjusting Projector Features

Follow the instructions in these sections to use your projector's feature adjustments.
Shutting Off the Picture Temporarily Projector Security Features Saving Settings to Memory and Using Saved Settings

Shutting Off the Picture Temporarily

You can temporarily turn off the projected picture if you want to redirect your audience's attention during a presentation. Any video action continues to run, however, so you cannot resume projection at the point that you stopped it.
1. Press the Blank button on the remote control to temporarily stop projection.
2. To turn the picture back on, press the Blank button again.
Parent topic: Adjusting Projector Features

Projector Security Features

You can secure your projector to deter theft or prevent unintended use by setting up the following security features:
• Button lock security to block operation of the projector using the buttons on the control panel.
• Security cabling to physically cable the projector in place.
Locking the Projector's Buttons Installing a Security Cable
Parent topic: Adjusting Projector Features
63

Locking the Projector's Buttons

You can lock the buttons on the projector's control panel to prevent anyone from using the projector. You can lock all the buttons or all the buttons except the power button.
1. Press the Menu button.
2. Select the Settings menu and press Enter.
3. Select the Lock Setting setting and press Enter.
4. Select one of these lock types and press Enter:
• To lock the projector's power button, select Child Lock. To turn the projector on, you must press
the power button for longer than three seconds.
• To lock all buttons except the power button, select Control Panel Lock. You see a confirmation prompt.
5. Select Yes and press Enter.
6. Restart the projector for the lock settings to take effect.
Unlocking the Projector's Buttons
Parent topic: Projector Security Features Related references
Projector Feature Settings - Settings Menu
64
Unlocking the Projector's Buttons
If the projector's buttons have been locked, hold the Enter button on the projector's control panel for seven seconds to unlock them.
Parent topic: Locking the Projector's Buttons

Installing a Security Cable

You can use the security slot on the back of the projector to attach a Kensington Microsaver Security system, available from Epson.
Parent topic: Projector Security Features

Saving Settings to Memory and Using Saved Settings

You can save customized settings for each of your video inputs and then select the saved settings whenever you want to use them.
1. Turn on the projector and display an image.
2. Press the Menu button. Note: You can also press the Memory button on the remote control to access the Memory menu
directly.
3. Select the Settings menu and press Enter.
4. Select the Memory setting and press Enter. You see this screen:
65
5. Select one of the following options:
Load Memory: Overwrites your current settings with saved settings
Save Memory: Saves your current settings to memory (10 memories with different names are
available) Note: A memory name that is being used is indicated by a green mark. Saving over a previously
saved memory overwrites the settings with your current settings.
Erase Memory: Erases the selected memory settings
Rename Memory: Renames a saved memory
Parent topic: Adjusting Projector Features
66

Using WirelessHD

You can use the included WirelessHD transmitter to wirelessly stream HD content from a video device to the projector (PowerLite Home Cinema 5030UBe).
WirelessHD Transmitter Placement Connecting the WirelessHD Transmitter Viewing WirelessHD Content Switching WirelessHD Sources Using the WirelessHD Picture-in-Picture Feature

WirelessHD Transmitter Placement

Keep these considerations in mind as you select a WirelessHD transmitter location:
• Place the WirelessHD transmitter so that the unit's lights face the front of the projector.
• Make sure the WirelessHD transmitter is within 32 feet (10 m) of the projector and is located in the
same room.
• Ensure there is a clear path between the projector and the WirelessHD transmitter.
• Avoid placing the WirelessHD transmitter in an area with many large or metal objects. Do not place the
WirelessHD transmitter on a metal surface, as this may interfere with the signal.
Parent topic: Using WirelessHD

Connecting the WirelessHD Transmitter

You can connect up to five HDMI input sources and one HDMI output source to your WirelessHD transmitter.
1. Plug the AC adapter into the AC input port on the WirelessHD transmitter and into an electrical outlet.
67
2. Connect HDMI cables to your video devices and to the HDMI input ports on the side and back of the WirelessHD transmitter.
Note: You can connect an MHL-compatible smartphone or tablet to the HDMI 5 / MHL (IN) port on the WirelessHD Transmitter.
3. To use the WirelessHD transmitter as a pass-through device to a television or other display, connect an HDMI cable to the display device and to the HDMI output port on the back of the transmitter.
Parent topic: Using WirelessHD

Viewing WirelessHD Content

Turn on the video equipment or computer you want to use before you turn on the WirelessHD transmitter and projector.
1. Turn on the power switch on the side of the transmitter.
2. Turn on the projector.
68
3. Press the WirelessHD button on the remote control.
The WiHD light on the transmitter lights up and your projector displays WirelessHD content.
Note: If the WirelessHD connection fails, press the Setup button on the bottom of the WirelessHD transmitter and try again.
Parent topic: Using WirelessHD

Switching WirelessHD Sources

If you have connected multiple HDMI input sources to your WirelessHD transmitter, you can use the projector remote control to switch between sources.
1. Press the Input button on the remote control or the WirelessHD transmitter.
Note: Make sure to point the remote control at the WirelessHD transmitter. You see this screen:
69
2. Press the Input button repeatedly to highlight different input sources.
3. When you have highlighted the source you want to switch to, release the Input button.
The display automatically switches to the highlighted source after a few seconds.
Parent topic: Using WirelessHD

Using the WirelessHD Picture-in-Picture Feature

If you have connected multiple video sources to the WirelessHD transmitter, you can use the Picture-in­Picture (P-in-P) feature to wirelessly project images from two separate sources at the same time.
1. Press the P-in-P button on the remote control.
2. Do the following to control the P-in-P display:
• Press the Input button on the remote control or the WirelessHD transmitter to change the video
source displayed in the sub-screen. Keep pressing the button to cycle through all of the connected video devices.
• Press the Output button on the remote control or the WirelessHD transmitter to change the
position of the sub-screen. The screen moves counterclockwise from corner to corner each time the Output button is pressed.
70
• Press and hold the P-in-P button on the remote control to switch the sources shown in the main
display and the sub-screen.
3. When you are finished watching Picture-in-Picture, press the P-in-P button on the remote control to resume normal projection.
Parent topic: Using WirelessHD
71

Adjusting the Menu Settings

Follow the instructions in these sections to access the projector menu system and change projector settings.
Using the Projector's Menus Image Quality Settings - Image Menu Input Signal Settings - Signal Menu Projector Feature Settings - Settings Menu Projector Setup Settings - Extended Menu Projector Memory Options - Memory Menu Projector Information Display - Info Menu Projector Reset Options - Reset Menu

Using the Projector's Menus

You can use the projector's menus to adjust the settings that control how your projector works. The projector displays the menus on the screen.
1. Press the Menu button on the control panel or remote control.
You see the menu screen displaying the Image menu settings.
72
2. Press the up or down arrow buttons to move through the menus listed on the left. The settings for each menu are displayed on the right.
Note: The available settings depend on the current input source.
3. To change settings in the displayed menu, press Enter.
4. Press the up or down arrow button to move through the settings.
5. Change the settings using the buttons listed on the bottom of the menu screens.
6. To return all the menu settings to their default values, select Reset.
7. When you finish changing settings on a menu, press Esc.
8. Press Menu or Esc to exit the menus.
Parent topic: Adjusting the Menu Settings

Image Quality Settings - Image Menu

Settings on the Image menu let you adjust the quality of your image for the input source you are currently using. The available settings depend on the currently selected input source.
73
To change settings for an input source, make sure the source is connected and select that source.
Setting Options Description Color Mode See the list of available Color Adjusts the vividness of image
Modes colors for various image types
and environments
Brightness Varying levels available Lightens or darkens the overall
image
Contrast Varying levels available Adjusts the difference between
light and dark areas of the image
Color Saturation Varying levels available Adjusts the intensity of the image
colors
Tint Varying levels available Adjusts the balance of green to
magenta tones in the image
Sharpness Varyinglevels available Adjusts the sharpness or
softness of image details
Color Temp. (color temperature) Varying levels available Sets the overall color tone; higher
values tint the image blue and lower values tint the image red
74
Setting Options Description Skin Tone Varyinglevelsavailable Makes fine adjustments to the
color tone; higher values tint the image blue and lower values tint the image red
Advanced Gamma Selects various detailed color
RGB RGBCMY EPSON Super White
settings Gamma: adjusts the gamma
levels of the image RGB: adjusts the offset and gain
for each color RGBCMY: adjusts the hue,
saturation, and brightness for each color
EPSON Super White: reduces over-exposure of whites in your image; can be set only when Color Mode is set to Natural,
Cinema, THX, 3D THX, B&W Cinema, or 3D Cinema.
Power Consumption Normal Selectsthebrightnessmodeof
ECO
the projector lamp Normal: sets maximum lamp
brightness ECO: reduces lamp brightness
and fan noise, and saves power and lamp life
Auto Iris Off Adjusts the projected luminance
Normal High Speed
based on the image brightness when certain Color Modes are selected
Note: The Brightness setting does not affect lamp brightness. To change the lamp brightness mode, use the Power Consumption setting.
75
Parent topic: Adjusting the Menu Settings Related concepts
Color Mode

Input Signal Settings - Signal Menu

Normally the projector detects and optimizes the input signal settings automatically. If you need to customize the settings, you can use the Signal menu. The available settings depend on the currently selected input source.
To change settings for an input source, make sure the source is connected and select that source.
76
Setting Options Description 3D Setup 3D Display Selects various 3D options
2D-to-3D Conversion 3D Display: enables 3D mode 3D Format 2D-to-3D Conversion: converts 3D Depth Diagonal Screen Size 3D Brightness Inverse 3D Glasses 3D Viewing Notice
2D images to 3D 3D Format: selects the 3D
format 3D Depth: sets the depth for the
3D image Diagonal Screen Size: selects
the actual size of the screen to maximize the 3D effect
3D Brightness: adjusts the brightness of the 3D image
Inverse 3D Glasses: reverses the images projected for the left and right eyes (enable only if 3D images do not display correctly)
3D Viewing Notice: enables the viewing notice displayed when using 3D mode
Aspect See the list of available aspect Sets the aspect ratio (width-to-
ratios height ratio) for the selected input
source
Tracking Varyinglevelsavailable Adjusts signal to eliminate
vertical stripes in computer images from the PC input port
Sync. Varying levels available Adjusts signal to eliminate
fuzziness or flickering in computer images from the PC input port
Position Up, down, left, right Adjusts the image location on the
screen
77
Setting Options Description Deinterlacing Off Sets whether to convert
Video Film/Auto
interlaced-to-progressive signals for certain video image types
Off: for fast-moving video images Video: for most video images Film/Auto: for movies, computer
graphics, and animation
Motion Detection 1 to 5 Selects how the image is
converted to a progressive signal (Adjust this setting if you
experience problems with still image quality or flickering video. Select a lower setting for still images or a higher setting for fast-moving video content.)
Frame Interpolation Off Smooths fast moving video by
Low Normal
comparing consecutive frames and inserting an intermediate frame between them
High
Super-resolution 0 to 5 Sharpens blurred images Auto Setup On Automatically optimizes
Off
78
computer image quality
Setting Options Description Advanced Noise Reduction NoiseReduction: reduces
Setup Level Overscan HDMI Video Range Image Processing
flickering in analog images in three levels
Setup Level: adjusts the level at which dark areas of the image are rendered black; leave this setting at 0% for most video equipment; check your video equipment specifications to verify the correct setting
Overscan: changes the projected image ratio to make the edges visible by a selectable percentage or automatically
HDMI Video Range: sets the video range to match the setting of the device connected to the HDMI input port
Image Processing: adjusts how images are processed; select Fast to display images quicker; select Fine to display images in higher quality
Note:
• The Deinterlacing setting is available only for 480i, 576i or 1080i signals from Component, HDMI, or
WirelessHD (PowerLite Home Cinema 5030UBe) video sources.
• You can set the HDMI Video Range setting only when the Epson Super White setting is set to Off.
• The Reset setting does not reset the Diagonal Screen Size, 3D Viewing Notice, Aspect, and Image
Processing settings.
• When you view 3D images, the Frame Interpolation and Super-resolution settings are only
available for 1080p 24 fps signals from HDMI video sources .
• The Aspect setting is not available for HD video signals.
79
Parent topic: Adjusting the Menu Settings Related concepts
Image Aspect Ratio
Related tasks
Viewing 3D Images

Projector Feature Settings - Settings Menu

Options on the Settings menu let you customize various projector features.
Setting Options Description Keystone Varying levels available Adjusts image shape to
rectangular (vertically)
80
Setting Options Description HDMI Link Device Connections Adjusts the HDMI Link options
HDMI Link Power On Link Power Off Link
that allow the projector remote to control HDMI-connected devices that support the CEC standard
Device Connections: lists the devices connected to the HDMI1 and HDMI2 ports
HDMI Link: enables or disables the HDMI Link function
Power On Link: controls what happens when you turn on the projector or a linked device
PJ -> Device or Bidirectional: turns on the linked device when the projector is turned on
Device -> PJ or Bidirectional: turns on the projector when the linked device is turned on
Power Off Link: controls whether linked devices are turned off when the projector is turned off
81
Setting Options Description WirelessHD Device Connections Device Connections: displays a
(PowerLite Home Cinema WirelessHD 5030UBe)
Reception WiHD Mode
list of available WirelessHD devices
WirelessHD: controls whether the projector receives WirelessHD signals
Reception: displays the strength of the WirelessHD signal
WiHD Mode: adjusts the WirelessHD signal strength and range
Normal: use this default setting in most situations
Full: uses the maximum video bandwidth at all times
Dynamic: provides extended signal range while adjusting the video bandwidth in real time; if your WirelessHD signal is weak, try changing the WiHD Mode to Dynamic
Lock Setting Child Lock Controls projector button locking
Control Panel Lock
to secure the projector Child Lock: locks the power
button Control Panel Lock: locks all
buttons except the power button
Projection Front Selects the way the projector
Front/Ceiling
faces the screen so the image is oriented correctly
Rear Rear/Ceiling
82
Setting Options Description User Button 2D-to-3D Conversion Assigns a menu option to the
3D Depth 3D Brightness Inverse 3D Glasses Power Consumption Info
Picture in Picture See the list of available Picture in Adjuststhesizeandlocationof
Picture options the sub-screen, swaps sources
Parent topic: Adjusting the Menu Settings Related concepts
Projector Security Features Projector Placement
Related references
Available Picture in Picture Options
Related tasks
Correcting Image Shape with the Keystone Buttons Connecting to an HDMI Video Source Changing the Projection Mode Using the Menus
User button on the remote control for one-touch access
and exits Picture in Picture mode
Related topics
Using WirelessHD

Projector Setup Settings - Extended Menu

Settings on the Extended menu let you customize various projector setup features that control its operation.
83
Setting Options Description Operation Direct Power On Selects various operation
Sleep Mode Illumination Trigger Out High Altitude Mode
options Direct Power On: lets you turn
on the projector without pressing the power button
Sleep Mode: automatically turns off the projector after an interval of inactivity
Illumination: turns off the lights on the projector
Trigger Out: outputs a DC 12V signal from the 3.5 mm mini-jack Trigger Out port whenever the projector is turned on
High Altitude Mode: regulates the projector’s operating temperature at altitudes above 4921 feet (1500 m)
84
Setting Options Description Display Menu Position Selects various display options
Menu Color Menu Position: adjusts the Messages Display Background Startup Screen Standby Confirmation
location where the menu is displayed
Menu Color: selects the color of the menu
Messages: controls whether messages are displayed on the screen
Display Background: selects the screen color or logo to display when no signal is received
Startup Screen: controls whether a special screen appears when the projector starts up
Standby Confirmation: displays a confirmation message after pressing the Standby button on the remote control
Input Signal Video Signal Selects the input signals for
Component
certain ports Video Signal: Specifies the
signal type from input sources connected to the Video port or select Auto to detect the signal automatically
Component: Specifies the signal type from input sources connected to the Component port or select Auto to detect the signal automatically
85
Setting Options Description Panel Alignment Panel Alignment Corrects color misalignment in
Select Color Pattern Color Start Adjustments
Language Various languages available Selects the language for
Note: The Reset setting does not reset the High Altitude Mode or Language settings.
the projected image Panel Alignment: enables
adjustments for color convergence (the alignment of the red and blue colors in the projected image)
Select Color: specifies the color convergence to correct
Pattern Color: specifies the color pattern used during panel alignment
Start Adjustments: starts the Panel Alignment feature
projector menu and message displays (not changed by Reset option)
Parent topic: Adjusting the Menu Settings Related tasks
Adjusting the Color Convergence (Panel Alignment)

Projector Memory Options - Memory Menu

Your projector comes with 10 memory locations where you can save customized settings to obtain the best picture quality for each of your video inputs.
86
Setting Description Load Memory Displays the list of customized settings entries that you have
created; select an entry and press Enter on the remote control to load it
Save Memory Saves the current projector settings to the projector's memory Erase Memory Displaysthelistofcustomizedsettingsentriesthatyouhave
created; select an entry and press Enter on the remote control to erase it
Rename Memory Displays the list of customized settings entries that you have
created; select an entry and press Enter on the remote control to rename it
Parent topic: Adjusting the Menu Settings

Projector Information Display - Info Menu

You can display information about the projector and input sources by viewing the Info menu. However, you cannot change any settings in the menu. The information displayed depends on the currently selected input source.
87
Note: The lamp usage timer does not register any hours until you have used the lamp for at least 10
hours. Available settings depend on the current input source.
Information item Description Lamp Hours Displays the number of hours (H) the lamp has been used in each
Power Consumption mode; if the information is displayed in yellow, obtain a genuine Epson replacement lamp soon
Source Displays the name of the port to which the current input source is
connected
Input Signal Displays the input signal type setting of the current input source Resolution Displays the resolution of the current input source Scan Mode Displays the scan mode (progressive or interlaced) Refresh Rate Displays the refresh rate of the current input source 3D Format Displays the 3D format of the current input source Sync Info Displaysinformationthatmaybeneededbyaservicetechnician Deep Color Displays Deep Color information Status Displays information about projector problems that may be needed
by a service technician
Serial Number Displays the projector's serial number
88
Information item Description Version Displays the firmware version of the projector
Parent topic: Adjusting the Menu Settings Related references
Optional Equipment and Replacement Parts
Related tasks
Replacing the Lamp Resetting the Lamp Timer

Projector Reset Options - Reset Menu

You can reset most of the projector settings to their default values using the Reset All option on the Reset menu.
You can reset the projector's lamp usage timer to zero when you replace the lamp using the Reset Lamp Hours option and you can also reset all memory entries using the Reset Memory option.
You cannot reset the following settings using the Reset All option:
• PC Signal
• Language
• Lamp Hours
• Memory settings
89
Parent topic: Adjusting the Menu Settings
90

Maintaining and Transporting the Projector

Follow the instructions in these sections to maintain your projector and transport it from place to place.
Projector Maintenance Transporting the Projector

Projector Maintenance

Your projector needs little maintenance to keep working at its best. You may need to clean the lens periodically, and clean the air filter and air vents to prevent the projector
from overheating due to blocked ventilation. The only parts you should replace are the lamp, air filter, and remote control batteries. If any other part
needs replacing, contact Epson or an authorized Epson servicer. Warning: Before cleaning any part of the projector, turn it off and unplug the power cord. Never open
any cover on the projector, except as specifically explained in this manual. Dangerous electrical voltages in the projector can injure you severely.
Warning: Do not try to service this product yourself, except as specifically explained in this manual. Refer all other servicing to qualified servicers.
Cleaning the Lens Cleaning the 3D Glasses Cleaning the Projector Case Air Filter and Vent Maintenance Projector Lamp Maintenance Replacing the Remote Control Batteries
Parent topic: Maintaining and Transporting the Projector Related references
Where to Get Help

Cleaning the Lens

Clean the projector's lens periodically, or whenever you notice dust or smudges on the surface.
91
• To remove dust or smudges, gently move the shutter to the side and wipe the lens with lens-cleaning paper.
• To remove stubborn smudges, moisten a soft, lint-free cloth with lens cleaner and gently wipe the lens. Do not spray any liquid directly on the lens.
Warning: Do not use a lens cleaner that contains flammable gas. The high heat generated by the projector lamp may cause a fire.
Caution: Do not use glass cleaner or any harsh materials to clean the lens and do not subject the lens to any impacts; you may damage it. Do not use canned air, or the gases may leave a residue. Avoid touching the lens with your bare hands to prevent fingerprints on or damage to the lens surface.
Parent topic: Projector Maintenance

Cleaning the 3D Glasses

To remove dust, dirt, smudges, or fingerprints from the glasses, use a lint-free cloth.
Note: Unplug any charging cables from the glasses before cleaning them.
92
Caution: Do not use paper towels or any other abrasive materials to clean the glasses. Parent topic: Projector Maintenance

Cleaning the Projector Case

Before cleaning the projector case, turn off the projector and unplug the power cord.
• To remove dust or dirt, use a soft, dry, lint-free cloth.
• To remove stubborn dirt, use a soft cloth moistened with water and mild soap. Do not spray liquid directly on the projector.
Caution: Do not use wax, alcohol, benzene, paint thinner, or other chemicals to clean the projector case. These can damage the case. Do not use canned air, or the gases may leave a flammable residue.
Parent topic: Projector Maintenance

Air Filter and Vent Maintenance

Regular filter maintenance is important to maintaining your projector. Your Epson projector is designed with an easily accessible, user-replaceable filter to protect your projector and make regular maintenance simple. Filter maintenance intervals will depend on the environment.
If regular maintenance is not performed, your Epson projector will notify you when the temperature inside the projector has reached a high level. Do not wait until this warning appears to maintain your projector filter as prolonged exposure to high temperatures may reduce the life of your projector or lamp.
93
Damage due to the failure to properly maintain the projector or its filter may not be covered by the projector or lamp Limited Warranties.
Cleaning the Air Filter Replacing the Air Filter
Parent topic: Projector Maintenance Related references
Projector Light Status
Cleaning the Air Filter
You need to clean the projector's air filter in the following situations:
• The filter or vents get dusty.
• You see a message telling you to clean it.
1. Turn off the projector and unplug the power cord.
2. Press in on the inner edge of the air filter cover to release the latch, then pull to remove.
94
3. Pull the air filter out of the projector.
4. Tap each side of the air filter 4 to 5 times to shake off any excess dust.
Caution: Do not use excessive force when tapping the air filter, or it may crack and become unusable. Do not rinse the air filter in water, or use any detergent or solvent to clean it. Do not use canned air; the gases may leave a residue, or push dust and debris into the projector's optics or other sensitive areas.
95
5. Vacuum the front of the air filter (the side with the tabs) to remove any remaining dust.
Note: If dust is difficult to remove or the air filter is damaged, replace the air filter.
6. Place the air filter back in the projector as shown.
7. Close the air filter cover.
Parent topic: Air Filter and Vent Maintenance Related tasks
Replacing the Air Filter
Replacing the Air Filter
You need to replace the air filter in the following situations:
• After cleaning the air filter, you see a message telling you to clean or replace it
• The air filter is torn or damaged
96
• If the filter is a dark gray color
You can replace the air filter while the projector is mounted to the ceiling or placed on a table.
1. Turn off the projector and unplug the power cord.
2. Press in on the inner edge of the air filter cover to release the latch, then pull to remove.
3. Pull the air filter out of the projector.
Note: Air filters contain polypropylene. Dispose of used air filters according to local regulations.
97
4. Place the new air filter in the projector as shown.
5. Close the air filter cover.
Parent topic: Air Filter and Vent Maintenance

Projector Lamp Maintenance

The projector keeps track of the number of hours the lamp is used and displays this information in the projector's menu system.
Replace the lamp as soon as possible when the following occurs:
• The projected image gets darker or starts to deteriorate
• A message appears when you turn on the projector telling you to replace the lamp
• The projector's lamp light is flashing orange and its power light is flashing blue
Replacing the Lamp Resetting the Lamp Timer
Parent topic: Projector Maintenance Related references
Optional Equipment and Replacement Parts Projector Information Display - Info Menu Projector Lamp Specifications
Replacing the Lamp
Before you replace the lamp, let the projector cool down for at least one hour so the lamp will not be hot.
Warning: Let the lamp fully cool before replacing it to avoid injury.
98
You can replace the lamp while the projector is mounted to the ceiling, if necessary.
1. Turn off the projector and unplug the power cord.
2. Allow the projector lamp to cool down for at least one hour.
3. Use the screwdriver included with the replacement lamp to loosen the screw securing the lamp
cover.
Warning: If the lamp is broken, glass fragments may be loose inside the lamp chamber. Be careful removing any broken glass to avoid injury. If the projector is installed on the ceiling, stand to the side of the lamp cover and not underneath it; pieces of glass could fall into your eyes or mouth when you open the lamp cover.
99
4. Slide the lamp cover out and lift it off.
5. Loosen the screws securing the lamp to the projector. The screws do not come all the way out.
100
Loading...