Epson EB-X02 User Manual

User’s Guide

Notations Used in This Guide

•Safety indications

The documentation and the projector use graphical symbols to show how to use the projector safely. Please understand and respect these caution symbols in order to avoid injury to persons or property.

	Warning	This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling.
	Caution	This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling.
• General information indications
	Attention	Indicates procedures which may result in damage or injury if sufficient care is not taken.
	a	Indicates additional information and points which may be useful to know regarding a topic.
	s	Indicates a page where detailed information regarding a topic can be found.
	g	Indicates that an explanation of the underlined word or words in front of this symbol appears in the glossary of terms. See the "Glossary"
		section of the "Appendix".
		s "Glossary" p.99
	[Name]	Indicates the name of the buttons on the remote control or the control panel.
		Example: [Esc] button
	Menu Name	Indicates Configuration menu items.
		Example:
		Select Brightness from Image.
		Image - Brightness

Contents		3

Notations Used in This Guide . . . . . . . . . . . . . . . . . . . . . . . . 2

Introduction

Projector Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

List of Functions by Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Quick and Easy Set up, Projection, and Storage . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Connecting with a USB cable and projecting (USB Display) . . . . . . . . . . . . . . . . 8

Detecting projector movements and automatically correcting image distortion (EB-X14G/EB-W02/EB-X02/EB-S02 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Useful Functions for Projecting Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Increasing projection content in wide (WXGA) screen (EB-W02/EB-W01 only)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Making the most of the remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Enhanced security functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Part Names and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Front/Top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Replacing the remote control batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Remote control operating range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Preparing the Projector

Installing the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Installation Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Installation methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Screen Size and Approximate Projection Distance . . . . . . . . . . . . . . . . . . . . . . . 20

Connecting Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Connecting a Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Connecting Image Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Basic Usage

Projecting Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

From Installation to Projection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Automatically Detect Input Signals and Change the Projected Image (Source Search)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Switching to the Target Image by Remote Control . . . . . . . . . . . . . . . . . . . . . . . 28 Projecting with USB Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 System requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Connecting for the first time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Uninstalling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Adjusting Projected Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Correcting Keystone Distortion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Correcting automatically . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Correcting manually . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Adjusting the Image Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Adjusting the Image Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Adjusting the Horizontal Tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Correcting the Focus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Selecting the Projection Quality (Selecting Color Mode) . . . . . . . . . . . . . . . . . . . 37 Setting Auto Iris . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Changing the Aspect Ratio of the Projected Image . . . . . . . . . . . . . . . . . . . . . . 39 Changing methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Changing the aspect mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Useful Functions

Projection Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Hiding the Image and Sound Temporarily (A/V Mute) . . . . . . . . . . . . . . . . . . . . . 43 Freezing the Image (Freeze) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Pointer Function (Pointer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Enlarging Part of the Image (E-Zoom) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Using the Remote Control to Operate the Mouse Pointer (Wireless Mouse) . . . . . . 46 Saving a User's Logo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Contents		4

Security Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Managing Users (Password Protect) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Kinds of Password Protect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Setting Password Protect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Entering the Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Restricting Operation (Control Panel Lock) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Anti-Theft Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Installing the wire lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Monitoring and Controlling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

ESC/VP21 Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Before starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Command list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Communications protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Configuration Menu

Using the Configuration Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

List of Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Configuration Menu Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Image Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Signal Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Settings Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Extended Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Info Menu (Display Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Reset Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Troubleshooting

Using the Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Problem Solving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

No images appear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Moving images are not displayed (only the moving image portion turns black)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 Projection stops automatically . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 The message Not supported is displayed. . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 The message No Signal is displayed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 Images are fuzzy, out of focus, or distorted . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Interference or distortion appear in images . . . . . . . . . . . . . . . . . . . . . . . . . . 73 The image is truncated (large) or small, or the aspect is not suitable . . . . . . . . . 73 Image colors are not right . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Images appear dark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Problems when Projection Starts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 The projector does not turn on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 Other Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 No sound can be heard or the sound is faint . . . . . . . . . . . . . . . . . . . . . . . . . 76 The remote control does not work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 I want to change the language for messages and menus . . . . . . . . . . . . . . . . . 77

Maintenance

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Cleaning the Projector's Surface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 Cleaning the Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 Cleaning the Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Replacing Consumables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Replacing the Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 Lamp replacement period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 How to replace the lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 Resetting the lamp hours . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 Replacing the Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 Air filter replacement period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 How to replace the air filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Reading the Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 When the Indicators Provide No Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Problems Relating to Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Contents		5

Appendix

Optional Accessories and Consumables . . . . . . . . . . . . . . . . . . . . . . 87

Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Consumables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Screen Size and Projection Distance . . . . . . . . . . . . . . . . . . . . . . . . . 88

Projection Distance (For EB-W02/EB-W01) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 Projection Distance (For EB-X14G/EB-X02) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 Projection Distance (For EB-S02/EB-S01) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

Supported Monitor Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

Supported Resolutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 Computer signals (analog RGB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 Component Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 Composite video (EB-X14G/EB-W02/EB-X02/EB-S02 only) . . . . . . . . . . . . . . . . 93

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

Projector General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99

General Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

About Notations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

General Notice: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102

Introduction

This chapter explains the projector's features and the part names.

Projector Features		7

List of Functions by Model

Available functions differ depending on the model being used. See the table below for a list of the functions available for each model.

Function	EB-X14G	EB-W02	EB-X02	EB-S02	EB-W01	EB-S01
USB Display
Auto V-Keystone					-	-
H-Keystone		-	-	-	-	-
Quick Corner		-	-	-	-	-

Projector Features		8

Quick and Easy Set up, Projection, and Storage

Useful Functions for Projecting Images

• Turn the projector	on and	off by simply plugging in or unplugging.
• Project onto large	screens	from a short distance.

•Make easy height adjustments with one lever.

•No cool down delay makes it easy to put away.

Connecting with a USB cable and projecting (USB Display)

Increasing projection content in wide (WXGA) screen (EB-W02/EB- W01 only)

With a computer that has a 16:10 WXGA wide LCD display, the image can be projected in the same aspect. You can use whiteboards and other landscape format screens.

By simply connecting a USB cable, you can project images from a computer's screen without a computer cable.

s "Projecting with USB Display" p.28

s "Changing the Aspect Ratio of the Projected

Image " p.39

Detecting projector movements and automatically correcting image distortion (EB-X14G/EB-W02/EB-X02/EB-S02 only)

This projector automatically corrects vertical keystone distortion which occurs when positioning or moving the projector.

s "Correcting automatically" p.32

Making the most of the remote control

You can use the remote control to perform operations such as enlarging part of the image. You can also use the remote control as a pointer during presentations or as a mouse for the computer.

s "Pointer Function (Pointer)" p.43

s "Enlarging Part of the Image (E-Zoom)" p.45

s "Using the Remote Control to Operate the Mouse Pointer (Wireless Mouse)" p.46

Enhanced security functions

•Password Protect to restrict and manage users

By setting a Password you can restrict who can use the projector. s "Managing Users (Password Protect)" p.49

Projector Features		9

•Control Panel Lock restricts button operation on the control panel

You can use this to prevent people changing projector settings without permission at events, in schools, and so on.

s "Restricting Operation (Control Panel Lock)" p.51

•Equipped with various anti-theft devices

The projector is equipped with the following types of anti-theft security devices.

•Security slot

•Security cable installation point

s "Anti-Theft Lock" p.52

Part Names and Functions		10

All of the features in this guide are explained using illustrations of EB-W02 unless otherwise mentioned.

Front/Top

Name	Function
A Air exhaust vent	Exhaust vent for air used to cool the projector internally.

		Caution
		While projecting, do not put your face or hands
		near the air exhaust vent, and do not place objects
		that may become warped or damaged by heat near
		the vent.
B Sliding lens cover	Slide the knob to open and close the lens cover.
knob

Name	Function
C Foot adjust lever	Press the foot adjust lever to extend and retract the front
	adjustable foot.
	s "Adjusting the Image Position" p.36
D Front adjustable foot	When setup on a surface such as a desk, extend the foot to
	adjust the position of the image.
	s "Adjusting the Image Position" p.36
E Sliding lens cover	Close when not using the projector to protect the lens.

		Caution
		While projecting, do not close the lens cover.
F Remote receiver	Receives signals from the remote control.
G Focus ring	Adjusts the image focus.
	s "Correcting the Focus" p.37
H Zoom ring	Adjusts the image size.
(EB-X14G/EB-W02/EB-	s "Adjusting the Image Size" p.36
X02/EB-W01 only)
I Air intake vent	Takes in air to cool the projector internally.
(air filter)	s "Cleaning the Air Filter" p.79
J Air filter cover	Opens and closes the air filter cover.
	s "Replacing the Air Filter" p.84
K Speaker	Outputs audio.
L Indicators	Indicates the projector's status.
	s "Reading the Indicators" p.66
M Control panel	Operates the projector.
	s "Control Panel" p.13
N Lamp cover	Open when replacing the projector's lamp.
	s "Replacing the Lamp" p.81

Part Names and Functions		11

Rear

	Name	Function
A	Remote receiver	Receives signals from the remote control.
B	Power inlet	Connects the power cable to the projector.
		s "From Installation to Projection" p.26
C	Video port	Inputs composite video signals from video sources.
	(EB-X14G/EB-W02/EB-
	X02/EB-S02 only)
D	Security slot	The security slot is compatible with the Microsaver
		Security System manufactured by Kensington.
		s "Anti-Theft Lock" p.52
E	Lamp Cover Fixing	Screw to fix the lamp cover in place.
	Screw
F	Computer port	Inputs image signals from a computer and component
		video signals from other video sources.
G	USB(TypeB) port	• Connects the projector to a computer via a USB cable,
		and the image on the computer is projected.
		s "Projecting with USB Display" p.28
		• Connects the projector to a computer via a USB cable to
		use the Wireless Mouse function.
		s "Using the Remote Control to Operate the
		Mouse Pointer (Wireless Mouse)" p.46

	Name	Function
H	S-Video port	For S-video signals from video sources.
	(EB-X14G/EB-W02/EB-
	X02/EB-S02 only)
I	Audio-L/R port	Inputs audio from equipment connected to the Computer
	(EB-X14G/EB-W02/EB-	port, the S-Video port, or the Video port.
	X02/EB-S02 only)

Part Names and Functions		12

Base

	Name	Function
C	Front adjustable foot	When setup on a surface such as a desk, extend the foot to
		adjust the position of the image.
		s "Adjusting the Image Position" p.36
D	Security cable	Pass a commercially available wire lock through here and
	installation point	lock it in place.
		s "Installing the wire lock" p.52

Name	Function

ACeiling mount fixing Attach the optional Ceiling Mount here when suspending points (three points) the projector from a ceiling.

s "Installing the Projector" p.19

s "Optional Accessories" p.87

B Rear feet	When setup on a surface such as a desk, turn to extend and
	retract to adjust the horizontal tilt.
	s "Adjusting the Horizontal Tilt" p.37

Part Names and Functions		13

Control Panel

Name	Function
A [t] button	Turns the projector power on or off.
	s "From Installation to Projection" p.26
B [Source Search]	Changes to the next input source that is sending an image.
button	s "Automatically Detect Input Signals and Change the
	Projected Image (Source Search)" p.27
C [Enter] button	• When the Configuration menu or the Help screen is
[ ]	displayed, it accepts and enters the current selection and
	moves to the next level.

•If pressed while projecting analog RGB signals from the Computer port, you can automatically optimize Tracking, Sync., and Position.

	Name	Function
D	[w][v] buttons	• For EB-X14G
		Displays the Keystone screen allowing you to
		correct keystone distortion in vertical and horizontal
		directions.
		• For EB-W02/EB-X02/EB-S02/EB-W01/EB-S01
		Performs vertical keystone correction.
		s "Correcting manually" p.33
		• If pressed when the Configuration menu or the Help
		screen is displayed, these buttons select menu items and
		setting values.
		s "Using the Configuration Menu" p.55
		s "Using the Help" p.65
E	[Help] button	Displays and closes the Help screen which shows you how
		to deal with problems if they occur.
		s "Using the Help" p.65
F	[Esc] button	• Stops the current function.
		• If pressed when the Configuration menu is displayed, it
		moves to the previous menu level.
		s "Using the Configuration Menu" p.55

Part Names and Functions		14

Name

Function

Remote Control

G

[a][b] buttons

• For EB-X14G/EB-W02/EB-X02/EB-W01

or [Wide][Tele]

[a] Decreases the volume.

buttons

[b] Increases the volume.

s "Adjusting the Volume" p.37

• For EB-S02/EB-S01

[Wide]: Enlarges the size of the projected image.

[Tele]: Reduces the size of the projected image.

s "Adjusting the Image Size" p.36

• EB-X14G only

Corrects keystone distortion in the horizontal

direction when the Keystone screen is displayed.

s "H/V-Keystone (EB-X14G only)" p.33

• If pressed when the Configuration menu or the Help

screen is displayed, these buttons select menu items and

setting values.

s "Using the Configuration Menu" p.55

s "Using the Help" p.65

H

[Menu] button

Displays and closes the Configuration menu.

s "Using the Configuration Menu" p.55

Part Names and Functions		15

		Name		Function
A	[t] button			Turns the projector power on or off.
				s "From Installation to Projection" p.26
B	[Computer] button			Changes to images from the Computer port.
C	[Video] button			Each time the button is pressed, the input changes
				between images from the S-Video port to the Video port.
				(EB-X14G/EB-W02/EB-X02/EB-S02 only)
D	Numeric buttons			Enter the Password.
				s "Setting Password Protect" p.49
E	[Auto] button			If pressed while projecting analog RGB signals from the
				Computer port, you can automatically optimize Tracking,
				Sync., and Position.
F	[Aspect] button			Each time the button is pressed, the aspect mode changes.
				s "Changing the Aspect Ratio of the Projected Image "
				p.39
G	[Num] button			Hold down this button and press the numeric buttons to
				enter passwords and numbers.
				s "Setting Password Protect" p.49
H	[Menu] button			Displays and closes the Configuration menu.
				s "Using the Configuration Menu" p.55
I	[	][	][ ][ ]	• When the Configuration menu or the Help screen is
				displayed, pressing these buttons selects menu items
	buttons			and setting values.
				s "Using the Configuration Menu" p.55
				• During Wireless Mouse function, the mouse pointer
				moves in the direction of the button that was pushed.
				s "Using the Remote Control to Operate the
				Mouse Pointer (Wireless Mouse)" p.46

Name	Function
J [ ] button	• When the Configuration menu or the Help screen is
	displayed, it accepts and enters the current selection and
	moves to the next level.
	s "Using the Configuration Menu" p.55

•Acts as a mouse's left button when using the Wireless Mouse function.

s "Using the Remote Control to Operate the Mouse Pointer (Wireless Mouse)" p.46

K [User] button	Select any frequently used item from the five available
	Configuration menu items, and assign it to this button. By
	pressing the [User] button, the assigned menu item
	selection/adjustment screen is displayed, allowing you to
	make one-touch settings/adjustments.
	s "Settings Menu" p.59
	Power Consumption is assigned as the default setting.
L [Page] buttons	Changes pages in files such as PowerPoint files when using
[[][]]	the following projection methods.
	• When using the Wireless Mouse function
	s "Using the Remote Control to Operate the
	Mouse Pointer (Wireless Mouse)" p.46
	• When using USB Display
	s "Projecting with USB Display" p.28
M [E-Zoom] buttons	Enlarges or reduces the image without changing the
[z][x]	projection size.
	s "Enlarging Part of the Image (E-Zoom)" p.45
N [A/V Mute] button	• Turns the video and audio on or off.
	s "Hiding the Image and Sound Temporarily (A/V
	Mute)" p.43
	• You can change the Projection mode as follows by
	pressing the button for about five seconds.
	FrontWFront/Ceiling
	RearWRear/Ceiling

Part Names and Functions		16

	Name	Function
O	[Help] button	Displays and closes the Help screen which shows you how
		to deal with problems if they occur.
		s "Using the Help" p.65
P	[Freeze] button	Images are paused or unpaused.
		s "Freezing the Image (Freeze)" p.43
Q	[Volume] buttons	[a] Decreases the volume.
	[a][b]	[b] Increases the volume.
		s "Adjusting the Volume" p.37
R	[Pointer] button	Displays the on-screen pointer.
		s "Pointer Function (Pointer)" p.43
S	[Esc] button	• Stops the current function.
		• If pressed when the Configuration menu is displayed, it
		moves to the previous level.
		s "Using the Configuration Menu" p.55
		• Acts as a mouse's right button when using the Wireless
		Mouse function.
		s "Using the Remote Control to Operate the
		Mouse Pointer (Wireless Mouse)" p.46
T	[Color Mode] button	Each time the button is pressed, the Color Mode changes.
		s "Selecting the Projection Quality (Selecting Color
		Mode)" p.37
U	[LAN] button	Not available for this projector.
V	[USB] button	Changes to USB Display.
W	[Source Search]	Changes to the next input source that is sending an image.
	button	s "Automatically Detect Input Signals and Change the
		Projected Image (Source Search)" p.27
X	Remote control light-	Outputs remote control signals.
	emitting area

Replacing the remote control batteries

If delays in the responsiveness of the remote control occur or if it does not operate after it has been used for some time, it probably means that the batteries are becoming flat. When this happens, replace them with new batteries. Have two AA size manganese or alkaline batteries ready. You cannot use other batteries except for the AA size manganese or alkaline.

Attention

Make sure you read the following manual before handling the batteries.

s Safety Instructions

a Remove the battery cover.

While pushing the battery compartment cover catch, lift the cover up.

b Replace the old batteries with new batteries.

Part Names and Functions		17

Caution

Check the positions of the (+) and (-) marks inside the battery holder to ensure the batteries are inserted the correct way.

c Replace the battery cover.

Press the battery compartment cover until it clicks into place.

Remote control operating range

Preparing the Projector

This chapter explains how to install the projector and connect projection sources.

Installing the Projector		19

Installation Methods

The projector supports the following four different projection methods. Install the projector according to the conditions of the installation location.

• Project images from in front of			• Project images from behind a
the screen. (Front projection)			translucent screen. (Rear projec-
			tion)

Warning

•A special method of installation is required when suspending the projector from a ceiling (ceiling mount). If it is not installed correctly, it could fall causing an accident and injury.

•If you use adhesives on the Ceiling mount fixing points to prevent the screws from loosening, or if you use things such as lubricants or oils on the projector, the projector case may crack causing it to fall from its ceiling mount. This could cause serious injury to anyone under the ceiling mount and could damage the projector.

When installing or adjusting the ceiling mount, do not use adhesives to prevent the screws from loosening and do not use oils or lubricants and so on.

•Suspend the projector from the ceiling and project images from in front of a screen. (Front/Ceiling projection)

•Suspend the projector from the ceiling and project images from behind a translucent screen.

(Rear/Ceiling projection)

Attention

•Do not use the projector on its side. This may cause malfunctions to occur.

•Do not cover the projector's air intake vent or air exhaust vent. If either of the vents are covered, the internal temperature could rise and cause a fire.

a• An optional Ceiling mount is required when suspending the projector from a ceiling.

s "Optional Accessories" p.87

•The default Projection setting is Front. You can change from Front to Rear from the Configuration menu.

s Extended - Projection p.61

•You can change the Projection mode as follows by pressing down the [A/V Mute] button on the remote control for about five seconds.

FrontWFront/Ceiling RearWRear/Ceiling

Installation methods

Install the projector as follows.

Installing the Projector		20

• Install the projector so	that it	is parallel	to the screen.
If the projector is installed at an angle to			the screen, keystone distortion
occurs in the projected	image.

•Place the projector on a level surface.

If the projector is tilted the projected image is also tilted.

a• See the following if you cannot install the projector parallel to the screen.

s "Correcting Keystone Distortion" p.32

•See the following if you cannot install the projector on a level surface.

s "Adjusting the Horizontal Tilt" p.37 s "Correcting Keystone Distortion" p.32

Screen Size and Approximate Projection Distance

Projection size is determined by the distance from the projector to the screen. See the illustrations on the right to select the best position according to the screen size. The illustrations show the approximate shortest distance at maximum zoom. See the following for more information on the projection distance.

s "Screen Size and Projection Distance" p.88

aWhen you correct keystone distortion, the projected image may be reduced.

16:10 Screen Size

EB-W02/EB-W01

150”

(320×200cm)

100”

(220×130cm)

80”

(170×110cm)

50”

(110×67cm)

4:3 Screen Size

EB-X14G/EB-X02

Installing the Projector		21

EB-S02/EB-S01

Connecting Equipment		22

Illustrations in this section are of EB-W02.

The port name, location, and connector orientation differ depending on the source being connected.

Connecting a Computer

To project images from a computer, connect the computer using one of the following methods.

AWhen using the supplied or commercially available computer cable

Connect the computer's display output port to the projector's Computer port.

You can output audio from the projector's speaker by connecting the audio output port on the computer to the projector's Audio Input port using a commercially available audio cable. (EB-X14G/EB-W02/EB-X02/EB-S02 only)

BWhen using the supplied or commercially available USB cable

Connect the computer's USB port to the projector's USB(TypeB) port. You can send the computer's audio with the projected image.

a

• You can use a USB cable

to connect the projector to a computer to project images from the computer. This function is called USB Display.

s "Projecting with USB Display" p.28

• Depending on the model

used and the area of purchase, the computer cable or USB cable may not be supplied with the projector.

s "Optional Accessories"

p.87

Connecting Equipment		23

Connecting Image Sources

To project images from DVD players or VHS video and so on, connect to the projector using one of the following methods.

AWhen using a commercially available video or S-video cable (EB-X14G/EB-W02/EB-X02/EB-S02 only)

Connect the video output port on the image source to the projector's Video port.

Or, connect the S-video output port on the image source to the projector's S-Video port.

You can output audio from the projector's speaker by connecting the audio output port on the image source to the projector's Audio Input port using a commercially available audio cable.

BWhen using the optional component video cable s "Optional Accessories" p.87

Connect the component output port on the image source to the projector's Computer input port.

You can output audio from the projector's speaker by connecting the audio output port on the image source to the projector's Audio Input port using a commercially available audio cable. (EB-X14G/EB-W02/EB-X02/EB-S02 only)

Connecting Equipment		24

Attention

• If	the	input source is on when you connect it to the projector, it could cause a malfunction.
• If	the	orientation or shape of the plug differs, do not try to force it in. The device could be damaged or could	malfunction.
a		• If the source you want to connect to has an unusually shaped port, use the cable supplied with the device or an optional cable to connect to the projector.
		• When using a commercially available 2RCA(L/R)/stereo mini-pin audio cable, make sure it is labeled "No	resistance". (EB-X14G/EB-W02/EB-X02/EB-S02

only)

Basic Usage

This chapter explains how to project and adjust images.

Projecting Images

From Installation to Projection

This section explains the procedure for connecting the projector to a computer with the computer cable and projecting images.

a Connect the projector to an electrical outlet with the power cable.
b		Connect the projector to the computer with the computer cable.
c		Turn on the projector.
d Slide open the lens cover.
e		Turn on your computer.

26

f Change the computer's screen output.

When using a laptop computer, you need to change the screen output from the computer.

Hold down the Fn key (function key), and press the b key.

aThe method for changing differs depending on the computer being used. See the documentation supplied with the computer.

If the image is not projected, you can change the projected image using one of the following methods.

•Press the [Source Search] button on the control panel or the remote control.

s "Automatically Detect Input Signals and Change the Projected Image (Source Search)" p.27

•Press the button for the target port on the remote control. s "Switching to the Target Image by Remote Control" p.28

aAfter projecting the image, adjust the image if necessary. s "Correcting Keystone Distortion" p.32

s "Correcting the Focus" p.37

Example: EB-X14G/EB-W02/EB-X02/EB-S02

Projecting Images

Automatically Detect Input Signals and Change the Projected Image (Source Search)

Press the [Source Search] button to project images from the port currently receiving an image.

Using the remote control

Using the control panel

* (EB-X14G/EB-W02/EB-X02/EB-S02 only)

When two or more image sources are connected, press the [Source Search] button until the target image is projected.

When your video equipment is connected, start playback before beginning this operation.

27

aThe following screen is displayed while no image signals are input.

Projecting Images		28

Switching to the Target Image by Remote Control

You can change directly to the target image by pressing the following buttons on the remote control.

Remote control

AChanges to images from the Computer port.

BEach time the button is pressed, it cycles through the images being input from the following sources. (EB-X14G/EB-W02/EB-X02/EB-S02 only)

•S-Video port

•Video port

CChanges to USB Display.

Projecting with USB Display

You can use a USB cable to connect the projector to a computer to project images from the computer.

You can send the computer's audio with the projected image.

To start USB Display, set USB Type B to USB Display from the Configuration menu.

s Extended - USB Type B p.61

System requirements

For Windows

OS	Windows 2000*1
	Windows XP*2		Professional 32 bit
			Home Edition 32 bit
			Tablet PC Edition 32 bit
	Windows Vista		Ultimate 32 bit
			Enterprise		32 bit
			Business 32 bit
			Home Premium 32 bit
			Home Basic 32 bit
	Windows 7		Ultimate 32/64 bit
			Enterprise		32/64 bit
			Professional 32/64 bit
			Home Premium 32/64 bit
			Home Basic 32 bit
			Starter	32	bit
CPU	Mobile Pentium III	1.2 GHz		or	faster
	Recommended: Pentium M 1.6 GHz or faster

Projecting Images		29

Amount of Mem-	256 MB or more
ory	Recommended: 512 MB or more
Hard Disk	20 MB or more
Space
Display	Resolution of no less than 640x480 and no higher than
	1600x1200.
	Display color in 16-bit color or greater

*1 Service Pack 4 only

*2 Except for Service Pack 1

For Mac OS

OS	Mac OS X 10.5.x
	Mac OS X 10.6.x
CPU	Power PC G4 1GHz or faster
	Recommended: Core Duo 1.83GHz or faster
Amount of	512 MB or more
Memory
Hard Disk	20 MB or more
Space
Display	Resolution of no less than 640x480 and no higher than
	1600x1200.
	Display color in 16-bit color or greater

Connecting for the first time

The first time you connect the projector and the computer using the USB cable, the driver needs to be installed. The procedure is different for Windows and Mac OS.

a• You do not need to install the driver the next time you connect.

•When inputting images from multiple sources, change the input source to USB Display.

•If you use a USB hub, the connection may not operate correctly.

Connect the USB cable directly to the projector.

•Depending on the model used and the area of purchase, the USB cable may not be supplied with the projector.

For Windows

a Connect the computer's USB port to the projector's USB(TypeB) port using a USB cable.

aFor Windows 2000 or Windows XP, a message asking you if you want to restart your computer may be displayed. Select

No.

For Windows 2000

Double-click Computer, EPSON PJ_UD, and then

EMP_UDSE.EXE.

For Windows XP

Driver installation starts automatically.

For Windows Vista/Windows 7

When the dialog box is displayed, click Run EMP_UDSE.exe. b When the License Agreement screen is displayed, click Agree.

Projecting Images		30

c Computer images are projected.

It may take a while before computer images are projected. Until computer images are projected, leave the equipment as it is and do not disconnect the USB cable or turn off the power to the projector.

d Disconnect the USB cable when you finish projection.

When disconnecting the USB cable, there is no need to use Safely Remove Hardware.

a• If it is not installed automatically, double-click My Computer

- EPSON_PJ_UD - EMP_UDSE.EXE on your computer.

•If nothing is projected for some reason, click All Programs -

EPSON Projector - Epson USB Display - Epson USB Display Vx.xx on your computer.

•When using a computer running Windows 2000 under user authority, a Windows error message is displayed and you may not be able to use the software. In this case, try updating Windows to the latest version, restart, and then try to connect again.

For more details, contact your local dealer or the nearest address provided in the following document.

s Epson Projector Contact List

For Mac OS

a Connect the computer's USB port to the projector's USB(TypeB) port using a USB cable.

The Setup folder of USB Display is displayed in the Finder. b Double-click the USB Display Installer icon.

c Follow the on-screen instructions to install.

d When the License Agreement screen is displayed, click Agree.

Enter the administrator authority password and start the installation.

When the installation is complete, the USB Display icon is displayed in the Dock and menu bar.

e Computer images are projected.

It may take a while before computer images are projected. Until computer images are projected, leave the equipment as it is and do not disconnect the USB cable or turn off the power to the projector.

f When you finish projection, select Disconnect from the USB Display icon menu on the menu bar or Dock, and then remove the USB cable.

a• If the USB Display setup folder is not displayed automatically in the Finder, double-click EPSON PJ_UD - USB Display Installer on your computer.

•If nothing is projected for some reason, click the USB Display icon in the Dock.

•If there is no USB Display icon in the Dock, double-click USB Display from the Applications folder.

•If you select Exit from the USB Display icon menu on the Dock, USB Display does not start automatically when you connect the USB cable.

Uninstalling

For Windows 2000

a Click Start, select Settings, and then click Control Panel. b Double-click Add/Remove Programs.

c Click Change or Remove Programs.

d Select Epson USB Display and click Change/Remove.