Epson 710, 700, 500 User Manual

Important Information

Please read the following important information about your projector.
Important Safety Information
switched on as the bright light can damage your eyes. Never let children look into the lens when it is on.
lamp and filter covers. Dangerous electrical voltages inside the projector can cause severe injury. Except as specifically directed in this Owner’s Manual, do not attempt to service this product yourself. Refer all servicing to qualified service personnel.
and optional parts out of the reach of children. Children covering their heads with bags may result in death by suffocation. Be particularly careful around small children.
Caution:
bulb with your bare hands. The invisible residue left by the oil on your hands may be shorten the bulb life. Use a cloth or gloves to handle the new bulb.
Never look into the projector lens when the lamp is
Never open any covers on the projector except the
Keep the plastic bags for the projector, accessories
When you replace the lamp, never touch the new
EMP-710/700/500
Q
operation panel
Power
Source
Enter
Operation Panel
Keystone
Select
UICK
speaker
foot adjust lever
Button Function
Power Turns the projector on or off.
Help
Help Displays the Help menu. Source Switches the image source in order of computer →S-video
Enter Selects a menu option when the Help menu is displayed. Keystone +/- Adjusts a trapezoid distorted image to normal. Select Scrolls up and down, or right and left when the Help menu is
S
composite video.If there is no S-video input, the switch toggles between computer and composite video.
displayed.
TART
operation indicator
remote control receiver
zoom ring focus ring
front foot
EMP-710/700/500
Q
Button Function
Freeze Keeps the current computer or video image on the screen. A/V Mute Turns off the audio and video output of the projector. To turn on the audio and video output,
E-Zoom Pressing the right side of the button enlarges the image, pressing the left side of the button
Power Turns the projector on or off. Effect buttons Use to display special effects that have been assigned in the Effect menu. Enter Use the enter button to navigate the menus or use the remote as a mouse pointer when the
Illumination button
Esc Terminates the current function.
Menu Displays or hides the menu. Help Displays the Help menu. Comp Switches to the computer image from Computer. S-Video Switches to the video image from S-Video. Video Switches to the image from Video. Auto Optimizes the computer image. Resize Switches between the Window display and Resizing display. P in P Displays a subscreen on the main display. To display the subscreen, press the PinP button
Volume +/- Adjusts the volume.
press either the A/V mute button or Esc button again.
reduces the image. To display a portion of the enlarged image which is outside of the display area, press the Enter button to scroll the image.
projector is connected to the computer with the computer cable and the mouse cable. You can also select a menu option by pressing the center of this button (Enter). If you press the Enter when a menu or help is displayed, you access the next menu or screen. When the image source is a computer, the Enter button acts as the mouse left click.
Lights up all buttons on the remote control for 10 seconds.
If you press the Esc button when a menu or help is displayed, you go back to the previous screen or menu. When the image source is a computer, the Esc button acts as the mouse right click.
once. To hide the subscreen, press it again. To set the subscreen being displayed, press in the following order : [Menu] → [Setting] → [P in P]. The default settings are as follows; Subscreen size:1/9 division Main screen input source:Computer Subscreen input source:Video To change the subscreen position, press the Enter button. The subscreen will move to the selected direction.
UICK
Power
Freeze
A/V Mute
R/C ON
E-Zoom
3
4
2
1
Enter
Esc
Remote control
S
OFF
5
TART
®
DATA/VIDEO PROJECTOR
Owner’s Manual
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SEIKO EPSON CORPORATION. No patent liability is assumed with respect to the use of the information contained herein. Neither is any liability assumed for damages resulting from the use of the information contained herein.
Neither SEIKO EPSON CORPORATION nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to strictly comply with SEIKO EPSON CORPORATION’s operating and maintenance instructions.
SEIKO EPSON CORPORATION shall not be liable against any damages or problems arising from the use of any options or any consumable products other than those designated as Original EPSON Products or EPSON Approved Products by SEIKO EPSON CORPORATION.
EPSON is a registered trademark and PowerLite is a trademark of SEIKO EPSON CORPORATION.
General Notice: The following trademarks and registered trademarks are the
property of their respective owners and are used in this publication for identification purposes only.
EPSON/Seiko Epson Corp.
Macintosh, PowerBook/Apple Computer Corp.
IBM/International Business Machines, Inc.
Windows/Microsoft Corp. Other product names used herein are also for identification purposes only and
may be trademarks of their respective owners. EPSON disclaims any and all rights in those marks.

Contents

Contents iii Introduction vii
Getting the Most Out of Your Projector................................ix
Optional Accessories...................................................................ix
About This Manual.................................................................x
Safety Instructions.................................................................xi
Where to Get Help..............................................................xiii
World Wide Web site................................................................xiii
Transporting your projector......................................................xiv
1 Installation 1
Unpacking the Projector.........................................................2
Additional Components.............................................................. 3
Setting Up the Projector.........................................................4
Connecting to a Computer.....................................................6
Connecting to a PC Desktop Computer ..................................... 7
Connecting to a PC Laptop Computer.....................................10
Connecting to a Desktop Macintosh......................................... 13
Connecting to a PowerBook..................................................... 17
Connecting to a Video Source ..............................................22
Connecting to an External Speaker or PA System..................25
■ ■ ■ ■ ■
iii
2 Using the Projector 27
Turning the Equipment On and Off.....................................29
Turning the Projector On and Off............................................29
Focusing and Positioning the Screen Image ..........................31
Resize Button........................................................................... 33
Controlling the Projector......................................................34
Using the Remote Control....................................................... 35
Using the Operation Panel .......................................................38
Projector Status Indicators....................................................39
Operation Indicator.................................................................. 39
Lamp Indicator......................................................................... 40
Temperature Indicator.............................................................. 40
3 Using the Projector Menus 41
Accessing the Main Menu.....................................................42
Changing a Menu Setting.....................................................43
Menu Options......................................................................45
Video Menu (Image source = Computer) ................................. 45
Video Menu (Image source = Video)........................................ 47
Audio Menu............................................................................. 48
Effect Menu ............................................................................. 49
Setting Menu ...........................................................................49
User's Logo Menu ...................................................................50
Reset All Menu......................................................................... 52
Advanced Menu ....................................................................... 53
About Menu............................................................................. 54
■ ■ ■ ■
4 Maintenance 55
Cleaning the Lens.................................................................56
Cleaning the Projector Case..................................................56
Cleaning the Air Filter..........................................................57
Replacing the Lamp..............................................................58
Contents
iv
5 Troubleshooting 61
Problems with the Projector..................................................62
Problems with the Image or Sound.......................................64
6 Technical Specifications 67
Supported Monitor Displays.................................................69
Computer In connector pin assignments...............................71
Glossary 73 Index 75 World-Wide Warranty Terms 77
■ ■ ■ ■ ■
v
■ ■ ■ ■
vi
Contents

Introduction

Y
our compact, lightweight EPSON EMP-710/700/500 projector lets you project full-color images and video onto a large screen for presentations. You can connect it simultaneously to two image sources: one PC or Apple® Macintosh® computer image source, plus one video source such as a video tape deck, camcorder, or digital camera. You can also connect audio for each image source.
Images are displayed in full color (16,670,000 colors) at a XGA resolution of 1024 x 768 pixels (EMP-710/700) or SVGA resolution of 800 x 600 pixels (EMP-500). Your projector produces bright images that can be easily seen in rooms light enough to take notes. A totally new AVTSS™ (Automatic Video Tracking and Synchronization Sensing, patent pending) provides automatic set-up of image from a computer.
You control your projector through a hand-held remote control unit, with menus being provided for image source switching and image adjustment. The remote control can also act as a wireless mouse to control mouse operations on your computer screen during presentations.
■ ■ ■ ■ ■
vii
Your projector features the newest resizing technology DAR (Digital Active Resizing) which supports VGA~UXGA (EMP­710/700) and VGA~SXGA (EMP-500) computer output. No matter what type of computer output is used, the result is a full-size video image of outstanding clarity.
The video source can be NTSC, PAL or SECAM in composite video or S-Video format. See Chapter 6 for details on supported computers and video formats.
■ ■ ■ ■
viii
Introduction

Getting the Most Out of Your Projector

Your projector comes with a full set of features that enable you to control the settings for the image display, video and audio. To get the most out of your projector, read this section for a quick summary of the important features.

Optional Accessories

To enhance your use of the projector, EPSON provides the following optional accessories:
• Spare Lamp (EMP-710) ELPLP10S
• Spare Lamp (EMP-700/500) ELPLP10B
• Image Presentation Camera ELPDC01EX
• Mac Adapter Set ELPAP01
• Portable Screen ELPSC06
• VGA-Computer Cable (1.8m) ELPKC02
• VGA-Computer Cable (3.0m) ELPKC09 You can purchase these accessories from your dealer.
Getting the Most Out of Your Projector
■ ■ ■ ■ ■
ix

About This Manual

Chapter 1, “Installation”, gives step-by-step instructions on how to set up the projector and connect it to your computer, video source, or other external speaker or PA system. Read the installation procedures that apply to your configuration.
Chapter 2, “Using the Projector”, describes how to switch the projector on/off and control simple projector settings using the remote control or the operation panel.
Chapter 3, “Using the Menus”, describes how to use the menus to adjust the color and image settings, change the display of the projected image, and modify audio settings.
Chapter 4, “Maintenance”, describes how to clean your projector and perform limited maintenance.
Chapter 5, “Troubleshooting”, describes how to interpret your projector’s indicator lights and gives helpful information for avoiding errors, optimizing image quality and solving problems.
■ ■ ■ ■
Introduction
x
Chapter 6, “Technical Specifications,” lists the technical specifications for your projector.
A Glossary and Index are provided at the end of the manual.

Safety Instructions

Follow these safety instructions when setting up and using the projector:
1. Do not place the projector on an unstable cart, stand, or
table.
2. Do not use the projector near water or sources of heat.
3. Use attachments only as recommended.
4. Use the type of power source indicated on the projector.
If you are not sure of the power available, consult your dealer or local electricity company.
5. Place the projector near a wall outlet where the plug can
be easily unplugged.
6. Insert the projector’s three-pin grounding-type plug into
a properly grounded outlet. If you have a two-prong outlet, contact an electrician to replace it. Do not handle the plug with wet hands.
7. Take the following precautions when handling the plug.
Failure to comply with these precautions could result in sparks or fire.
• Do not insert the plug into an outlet with dust present.
• Insert the plug firmly into the outlet.
8. Do not overload wall outlets, extension cords or integral
convenience receptacles. This can cause fire or electric shock.
9. Do not place the projector where the cord can be stepped
on. It may result in fraying or damage to the plug.
10.Unplug the projector from the wall outlet before cleaning.
Use a damp cloth for cleaning. Do not use liquid or aerosol cleaners.
Safety Instructions
■ ■ ■ ■ ■
xi
11.Do not block the slots and openings in the projector case.
They provide ventilation and prevent the projector from overheating. Do not place the projector on a sofa, rug or other soft surface, or in a closed-in cabinet unless proper ventilation is provided.
12.Never push objects of any kind through cabinet slots.
Never spill liquid of any kind into the projector.
13.Except as specifically explained in this User’s Guide, do
not attempt to service this product yourself. Refer all servicing to qualified service personnel. Opening or removing covers may expose you to dangerous voltages and other hazards.
14.Unplug the projector during thunder storms or when it
will not be used for extended periods.
15.Do not place the projector and remote control on top of
heat-producing equipment or in a heated place, such as a car.
■ ■ ■ ■
xii
16.Unplug the projector from the wall outlet and refer
servicing to qualified service personnel under the following conditions:
• When the power cord or plug is damaged or frayed
• If liquid has been spilled into the projector, or it has been exposed to rain or water
• If it does not operate normally when you follow the operating instructions, or if it exhibits a distinct change in performance, indicating a need for service
• If it has been dropped or the housing has been damaged
17.When you use the projector in other countries except from where you purchased it, use the correct power cable suitable for that country.
Introduction

Where to Get Help

If you are having trouble setting up or running your projector, first see Chapter 5, “Troubleshooting”. If you cannot resolve the problem, contact the appropriate representative listed in the section entitled “World -Wide Warranty Terms” at the end of this manual.
Before you call, please have the following information ready:
• Product name
• Product serial number
• Computer configuration
• Description of the problem

World Wide Web site

If you connect to the Internet and have a Web browser, you can access to EPSON’s World Wide Web site at http:// www. epson. com. EPSON’s home page provides you What’s New, EPSON Products, EPSON Connection, Corporate Info and EPSON Contacts. Link to the EPSON Connection for the latest drivers and FAQ’s (Frequently Asked Questions) and the EPSON Chart area. To get in touch with EPSON around the world, EPSON Contacts includes Contact Information for local EPSON subsidiaries.
Where to Get Help
■ ■ ■ ■ ■
xiii

Transporting your projector

The projector contains many glass parts and precision parts. If you need to transport it, please follow these packing guidelines to prevent damaging the projector:
• When shipping the projector for repairs, use the original
packaging material. If you don’t have the original packaging, use equivalent
materials, placing plenty of cushioning around the projector.
• When transporting the projector for business use, first put
the projector in a hard carrying case, then pack it in a firm box, using cushioning around the case.
Note:
EPSON shall not be liable for any damages incurred
during transportation.
■ ■ ■ ■
xiv
Introduction
1

Installation

This chapter describes how to unpack and set up your
projector, and connect it to other equipment. The projector must be connected to a computer or a video source such as a video tape deck, camcorder, digital camera or laser disc player before it can project any images. You may also want to set up the projector for one or more of the following:
• Connect the mouse cable to use the remote control as a
wireless mouse.
• Provide audio for one or both image sources. The audio
source can be the computer, video source, or another device such as a stereo.
• Connect to an external speaker or PA system to amplify the
audio.
■ ■ ■ ■ ■
1

Unpacking the Projector

When you unpack the projector, make sure you have all these components:
• Projector
• Remote control
• 2 AA batteries
• Power cord
• Computer cable
• Audio/Video cable (A/V cable)
• PS/2 mouse cable
• USB mouse cable
• Mac mouse cable (ADB mouse cable)
• Owner’s manual
• Softcase
Depending on the configuration of your equipment, you may not need all these components.
Save all packaging materials in case you need to ship the projector in the future. It should be transported in its original packaging or the equivalent.
■ ■ ■ ■
2

Additional Components

Depending on how you plan to use the projector, you may need these additional components:
• To receive an S-Video signal, you need an S-Video cable.
(One is usually provided with your video device.) A separate cable is required for each video source.
• To connect the projector to a Macintosh PowerBook, you
need a video-out cable. (One is provided by/or can be purchased from Apple for all
new PowerBooks that have video-out capability.) If your PowerBook does not include one, see your Macintosh dealer.
• To connect the mouse cable to your computer, you may
require a special connector, cable, or other components. You can obtain these items from your computer dealer. If your computer doesn’t have a mouse connector, you cannot use the mouse cable.
Note:
You can connect a Kensington MicroSaver® anti-theft device in the hole on the projector’s right side. Contact your computer dealer.
Unpacking the Projector
■ ■ ■ ■ ■
3

Setting Up the Projector

1. Place the projector on a sturdy, level surface within five
feet of the computer or video source.
Caution:
Do not hold the projector by the lens. This can damage
the lens.
2. Place the projector at a correct distance from the screen.
The distance between the projector and the screen determines the actual image size. Use the general guidelines below to determine the correct distance.
Screen size Horizontal distance from projector to screen
300 inches (610x460cm) 450.7 inches (11.5m) ~ 546.3 inches (13.8m) 200 inches (410x300cm) 299.5 inches (7.7m) ~ 363.3 inches (9.2m) 150 inches (305x228cm) 223.9 inches (5.7m) ~ 271.7 inches (6.9m) 100 inches (200x150cm) 148.3 inches (3.8m) ~ 180.2 inches (4.5m) 80 inches (160x120cm) 118.1 inches (3.0m) ~ 143.6 inches (3.6m) 60 inches (120x90cm) 87.8 inches (2.3m) ~ 107.0 inches (2.7m) 40 inches (81x61cm) 57.6 inches (1.5m) ~ 70.4 inches (1.7m) 30 inches (61x46cm) 42.5 inches (1.1m) ~ 52.1 inches (1.3m) 26 inches (53x40cm) ~ 44.7 inches (1.1m)
3. Turn the projector so that the lens is at right angles to the
screen. If the projector is not angled correctly, the screen image will be crooked.
4. Connect one end of the power cable to the projector’s
power connector. Connect the other end to an earthed electrical socket. The projector should be in sleep mode, indicated by an orange power indicator.
■ ■ ■ ■
Never look into the lens when the projector is on. There is a risk that the projector might come on suddenly even though it is not in use. The light from the lamp can damage your eyes. It is especially important that children should not be allowed to look into the lens.
4
5. To insert the batteries in the remote control device, slide
off the battery compartment cover.
6. Insert the two AA batteries included with the projector.
Make sure the polarity of the batteries is correct.
7. Replace the battery compartment cover. When replacing batteries, take the following precautions:
• Do not recharge the used batteries or expose to fire or
water.
• Replace batteries as soon as they run out. If the batteries
leak, wipe away battery fluid with a soft cloth. If fluid gets on your hands, wash them immediately.
• Remove the batteries if you will not be using the projector
for a long period of time.
Setting Up the Projector
■ ■ ■ ■ ■
5

Connecting to a Computer

You can connect the projector to a computer capable of VGA, SVGA, XGA, SXGA and UXGA output. (EMP-500 supports VGA, SVGA, XGA, and SXGA resolutions. EMP-710/700 support VGA, SVGA, XGA, SXGA and UXGA resolutions.)
To connect the computer and mouse cables (to use the wireless remote as a mousepointer), see the section in this chapter that applies to your computer.
The illustration below identifies all the interface ports on the back of the projector; you may want to refer to this as you connect your computer or other equipment to the projector.
Audio In
Audio Out
Computer
InOut
Audio
S-Video
R
S-Video Video
Audio
L
Video
Computer
L-Audio-R
■ ■ ■ ■
Mouse/Com
Mouse/Com
USB Mouse
USB Mouse
Power Inlet
6

Connecting to a PC Desktop Computer

To connect the projector to your PC desktop computer, you need to:
• Connect the computer cable
• Connect the audio cable (if you’ll be projecting with audio) Follow the steps in each section for the cables you need to
connect. Before beginning, turn off the projector and computer if they are on.
Note:
Computer configurations vary. See your computer manual for the location of the ports needed to connect your projector.
Connecting the Computer and Monitor Cables
Refer to this illustration while following the steps below.
Computer port
computer cable
Connecting to a Computer
■ ■ ■ ■ ■
7
1. If you will be viewing the video on your computer
monitor as well as the projector screen, disconnect the monitor cable from the video port on the back of your computer.
2. Connect one end of the computer cable to the projector’s
Computer port.
3. Connect the other end of the computer cable to the
computer’s video port.
4. Tighten the screws on all connectors.
Connecting the Mouse Cables
If you want to use the remote control as a mouse, you need to connect the PS/2 mouse cable or USB mouse cable.
■ ■ ■ ■
Refer to this illustration while following the steps below.
USB mouse port
8
Mouse/Com port
PS/2 mouse cable
USB mouse cable
1. Connect the 9-pin end of the PS/2 mouse cable or, the
Audio n jack
audio cable
USB mouse cable to the Mouse/Com or USB mouse port on the projector.
2. Disconnect your mouse from the mouse port on the back
of your computer and replace it with the other end of the PS/2 mouse cable or USB mouse cable. (Your computer’s mouse will be disabled while you are using the remote control as a mouse.)
Connecting the Audio Cable
1. If you will be using audio, connect one end of the audio
cable to the Audio In jack on the projector.
2. Connect the other end of the audio cable to the speaker or
audio out port on the computer’s sound card.
Connecting to a Computer
■ ■ ■ ■ ■
9

Connecting to a PC Laptop Computer

To connect the projector to your PC laptop computer, you need to:
• Connect the computer cable
• Connect the mouse cable (if you want to use the remote
control as a mouse)
• Connect the audio cable (if you’ll be projecting with audio) Follow the steps in each section for the cables you need to
connect. Before beginning, turn off the projector and computer if they are on.
Note:
Laptop configurations vary. See your computer manual
for the location of the ports needed to connect your projector.
Connecting the Computer Cable
First connect the projector’s computer cable to your laptop.
Computer port
1. Connect one end of the computer cable to the projector’s
Computer port.
2. Connect the other end of the video cable to the laptop’s
video (monitor) port.
3. Tighten the screws on all connectors.
computer cable
■ ■ ■ ■
10
Connecting the Mouse Cables
If you want to use the remote control as a mouse, you need to connect the PS/2 mouse cable or USB mouse cable.
Refer to this illustration while following the steps below.
Mouse/Com port
PS/2 mouse cable
USB mouse cable
1. Connect the 9-pin end of the PS/2 mouse cable or USB
mouse cable to the Mouse/Com or USB Mouse port on the projector.
2. Connect the 6-pin (mini-DIN) end of the PS/2 mouse
cable or USB mouse cable to the external mouse port or USB port on your laptop.
3. Configure your laptop to work with an external mouse.
Connecting to a Computer
■ ■ ■ ■ ■
11
Note:
You may have to set the display to appear on both the laptop’s screen and the projector. Some laptops let you change this setting with the keyboard’s function keys or by using a setup utility provided by the computer manufacturer. Check your laptop’s manual or online help for instructions.
Connecting the Audio Cable
1. If you will be using audio, connect one end of the audio
cable to the Audio In jack on the projector.
Audio In jack
2. Connect the other end of the audio cable to your laptop.
audio cable
■ ■ ■ ■
12

Connecting to a Desktop Macintosh

To connect the projector to your desktop Macintosh, you need to:
• Connect the computer cable
• Connect the mouse cable (if you want to use the remote
control as a mouse)
• Connect the audio cable (if you’ll be projecting with audio) Follow the steps in each section for the cables you need to
connect. Before beginning, turn off the projector and computer if they are on.
Note:
Macintosh configurations vary. See your computer manual for the location of the ports needed to connect your projector.
Connecting the Computer Cable
First connect the computer cable. Refer to this illustration as you follow the steps below.
Computer port
Macintosh desktop adapter
computer cable
Connecting to a Computer
■ ■ ■ ■ ■
13
1. Connect one end of the computer cable to the projector’s
Computer port.
2. Remove the small cover on the Macintosh desktop adapter
and set its DIP switches in accordance with the resolution you want to use (such as 16-inch mode). See your Macintosh documentation for instructions.
■ ■ ■ ■
14
3. Connect the small terminal of the Macintosh desktop
adapter to the other end of the computer cable.
4. Connect the computer cable (with the Macintosh desktop
adapter attached) to the video-out port on your Macintosh.
Connecting the Mouse Cables
If you want to use the remote control as a mouse, you need to connect the Mac mouse cable or USB mouse cable.
Refer to this illustration while following the steps below.
Mouse/Com port
USB mouse cable
Mac mouse cable
Connecting to a Computer
■ ■ ■ ■ ■
15
1. Connect one end of the projector’s Mac mouse cable or
USB mouse cable to the Mouse/Com or USB Mouse port on the projector
2. Disconnect your Macintosh’s mouse cable. Connect the
other end of the projector’s Mac mouse cable or USB mouse cable to the mouse port on your Macintosh.
Connecting the Audio Cable
1. If you will be using audio, connect one end of the audio
cable to the Audio In jack on the projector.
■ ■ ■ ■
16
Audio In jack
audio cable
2. Connect the other end of the audio cable to the Audio
Out port on your computer.

Connecting to a PowerBook

Your PowerBook must have video-out capability in order to connect to the projector.
To connect the projector to your PowerBook, you need to:
• Connect the computer cable
• Connect the mouse cable (if you want to use the remote
control as a mouse)
• Connect the audio cable (if you’ll be projecting with audio) Follow the steps in each section for the cables you need to
connect. Before beginning, turn off the projector and computer if they are on.
Note:
PowerBook configurations vary, so the location of your computer’s ports may not match the illustrations. See your PowerBook manual for the port locations if necessary.
Connecting the Computer Cable
First connect the computer cable. Refer to this illustration as you follow the steps below.
Computer port
computer cable
Macintosh desktop adapter
video-out cable
Connecting to a Computer
■ ■ ■ ■ ■
17
Note:
Some new PowerBooks may allow you to connect the computer cable directly to the computer without using a video-out cable. See your PowerBook manual for additional information on connecting a computer cable.
1. Connect one end of the computer cable to the projector’s
Computer port.
2. Remove the small cover on the Macintosh desktop adapter
and set its DIP switches in accordance with the resolution you want to use (such as 16-inch mode). See your Macintosh documentation for instructions.
■ ■ ■ ■
18
3. Connect the small terminal of the Macintosh desktop
adapter to the other end of the computer cable.
4. Connect the computer cable (with the Macintosh desktop
adapter attached) to the video-out port on the PowerBook.
If a video-out cable was provided with your PowerBook, connect the smaller end of the video-out cable to the video­out port on the back of the PowerBook. Connect the other end to the Macintosh desktop adapter on the end of the computer cable.
Connecting to a Computer
■ ■ ■ ■ ■
19
Connecting the Mouse Cables
If you want to use the remote control as a mouse, you need to connect the Mac mouse cable or USB mouse cable.
Refer to this illustration while following the steps below.
Mouse/Com port
Mac mouse cable
USB mouse cable
1. Connect one end of the projector’s Mac mouse cable or
USB mouse cable to the Mouse/Com or USB Mouse port on the projector.
■ ■ ■ ■
20
2. Connect the other end of the Mac mouse cable or USB
mouse cable to the mouse port on the back of the PowerBook.
Connecting the Audio Cable
1. If you will be using audio, connect one end of the audio
cable to the Audio In jack on the projector.
Audio In jack
audio cable
2. Connect the other end of the audio cable to the audio-out
port on your PowerBook.
Note:
After you turn on the projector and computer, you’ll need to choose Mirroring in the Display Control Panel if you set up your configuration to display on the LCD screen as well as the projector screen.
Connecting to a Computer
■ ■ ■ ■ ■
21

Connecting to a Video Source

You can connect a VCR, a camcorder, a laser disc player, DVD player, or any other compatible video image source to your projector.
The projector can receive composite video or S-Video. Your equipment has composite video if your video source has a one-pin RCA video jack. Your equipment has S-Video if your video source has a four-pin (mini-DIN) video jack.
Note:
The projector is not compatible with a cable TV-style F connector.
You can connect the projector to an S-Video source and a composite video source at the same time.
The projector supports NTSC, PAL, and SECAM video formats, and automatically detects and identifies the video format. However, you can specify that a single broadcast format be detected. (See Chapter 3.) Note that the projector will then be able to detect only one type of video signal.
The type of cable you use to connect the video source to the projector depends on whether you have composite video or S-Video. For composite video, use the RCA audio and RCA video cable supplied with the projector. For S-Video, use the S-Video cable supplied with your video device or obtain one from your computer or video equipment dealer.
S-Video 4-pin, mini-DIN
1
3
2
4
composite RCA
To connect a video source to the projector:
■ ■ ■ ■
1. Turn off the projector and video source if they are on.
22
2. If your video source uses a small, round, one-prong
composite (RCA) video connector, you’ll need the RCA video cable that comes with the projector. If your video source uses a large, round, four-prong S-Video connector, you will need to purchase the appropriate cable or use the cable that came with your video source.
3. For Composite Video, connect the yellow RCA plug on
one end of the RCA video cable to the projector’s Video jack. Connect the other yellow RCA plug to the video-out jack of your video source.
RCA audio cable
RCA video cable
4. Connect the RCA audio cable to the Audio jacks of the
projector: insert the white plug into the L jack and the red plug into the R jack. Connect the plug at the other end of the RCA audio cable to the audio output jacks of the video source.
5. For S-Video, insert one end of an S-Video cable into the
projector’s S-Video connector. Insert the other end into the S-video out jack of your video source.
Connecting to a Video Source
■ ■ ■ ■ ■
23
6. Connect the RCA audio cable to the Audio jacks of the
projector: insert the white plug into the L jack and the red plug into the R jack. Connect the plug at the other end of the RCA audio cable to the audio output jack of the video source.
S-Video connector
S-Video cable
■ ■ ■ ■
24

Connecting to an External Speaker or PA System

Although the projector’s internal speakers are enough for most small- or medium-size rooms, you can connect the projector to an external speaker or public address (PA) system for large rooms or to gain maximum benefit.
To connect the projector to an external sound system, you need to obtain an RCA-to-3.5 mm stereo audio cable. You can get one from your computer dealer.
1. Turn off the projector and speaker or PA system if they are
on.
2. Connect the cable’s 3.5 mm stereo miniplug to the
projector’s Audio Out jack.
Audio Out jack
stereo audio cable
3. Connect the RCA plugs to the external amplified speaker
or PA system. Insert the cable’s red plug into the Audio R jack, and the white plug into the Audio L jack.
Note:
The internal speakers are disabled when an external
audio system is used.
Connecting to an External Speaker or PA System
■ ■ ■ ■ ■
25
■ ■ ■ ■
26
2

Using the Projector

This chapter provides the following information about using
your projector:
• Turning the equipment on and off
• Focusing and positioning the screen image
• Controlling the projector with the remote control and the
operation panel
• Monitoring the projector’s operating status
■ ■ ■ ■ ■
27
The illustration below identifies the parts of your projector.
operation indicator
operation panel
zoom ring
focus ring
front foot
speaker
foot adjust lever
remote control receiver
■ ■ ■ ■
28

Turning the Equipment On and Off

Turn on the projector and its attached equipment in the following order.
1. Video source
2. Audio source (if different from computer or video source)
3. Projector
4. External speaker or PA system (if necessary)
5. Computer When you turn off the equipment, do so in the reverse order.

Turning the Projector On and Off

1. Remove the projector lens cap.
2. When you plug in the projector power cord, the power
indicator flashes orange for few seconds. Then the light remains orange.
3. Press the Power button on the remote control or
operation panel. The power indicator flashes green as the projector warms up. When the projector is fully warmed up, this light remains green.
If computer or video equipment is attached, the computer or video signal is projected.
Warning:
Never look into the lens when the lamp is on. This can damage your eyes. It is especially important that children are not allowed to look into the lens.
Caution:
When turning the projector on or off with the remote control, be sure to turn the remote control on first with the power switch.
Turning the Equipment On and Off
■ ■ ■ ■ ■
29
After you press the power button to turn off the projector, a confirmation message appears. If you want to turn off the projector, press the power button again. If you don’t want to turn off the projector, press any button. The fan will remain on and the operation indicator will flash orange for about one minute as the projector cools down.
operation indicator
When the projector has cooled down, the operation indicator stops flashing and remains orange.
■ ■ ■ ■
30
Note:
If you press the Power button to turn the projector back on while the operation indicator is orange, there may be a delay before a projected image appears.

Focusing and Positioning the Screen Image

When an image appears on the screen, check that it is in focus and correctly positioned on the screen.
zoom ring
focus ring
• To focus the image, rotate the focus ring (the outer ring on
the lens).
• To adjust the size of the image, rotate the inner zoom ring.
Rotate the zoom ring between W (wide) and T (tele) marks.
Focusing and Positioning the Screen Image
■ ■ ■ ■ ■
31
If you need to raise or lower the image on the screen, extend or retract the two feet at the bottom of the projector as follows:
1. Stand behind the projector and support the front of it
while you lift the foot adjust levers above the feet. This unlocks the feet so they can move up and down freely. Do not let the projector drop.
■ ■ ■ ■
32
Caution:
Do not hold the projector by its lens. This can damage
the lens.
2. While lifting the foot adjust levers, raise or lower the
projector until the screen image is positioned correctly.
3. Release the lever to lock the feet in their new position.
4. To fine-tune the height of the projector, turn the feet
clockwise to raise the height or anti-clockwise to lower it.

Resize Button

The Resize button allows you to select the projection method for certain types of image input signals from a computer.
With images up to XGA size (1024 × 768) or SVGA size (800 x 600), you can choose from two projection methods. You can either display the image in the center of the projection area(Window display) or display the image full size(Resize display).
You can also choose from two projection methods with images greater than XGA or SVGA size: either project a portion of the image or project the entire image in a compressed format. The projector automatically reduces the image size to the projector's maximum resolution. The Resize button cannot be used with images at XGA or SVGA resolution.
When the image source is Video, the resize button lets you choose an aspect ratio either resize display or 16:9.
Focusing and Positioning the Screen Image
■ ■ ■ ■ ■
33

Controlling the Projector

You can use the operation panel on top of the projector or the remote control to perform the following actions:
• Turn the power on or off
• Auto set-up of the computer image
• Switch between input images (Computer, video-computer)
• Access the projector menus to adjust the image, audio,
video, and display settings
• Resize the projected image
• Freeze the display
• Temporarily display a blank screen
• Adjust or mute audio/video output
• Use custom functions
• Move the mouse pointer
■ ■ ■ ■
34

Using the Remote Control

Power
Freeze
A/V Mute
R/C ON
E-Zoom
Enter button
Esc button
To use the remote control, point it towards the remote control receivers located at the front and back of the projector.
To be able to use the remote control as a cordless mouse, connect the mouse cable to the projector and your computer.
OFF
3
4
2
5
1
Enter
Esc
Remote control
You can use the remote control up to 10 metres (30 feet) from the projector.
Note:
The projector may not respond to remote control commands in these conditions: ambient light is too bright; a certain type of fluorescent light is present; a strong light source (such as direct sunlight) shines into the infrared receiver; or other equipment emitting infrared energy is present (such as a radiant room heater). Correct these conditions to use the remote control or control the projector from a computer.
Controlling the Projector
■ ■ ■ ■ ■
35
This table summarizes the functions on the remote control.
Button Function
Freeze Keeps the current computer or video image on the
screen.
A/V Mute Turns off the audio and video output of the projector.
To turn on the audio and video output, press either the A/V mute button or Esc button again.
E-Zoom Pressing the right side of the button enlarges the
image, pressing the left side of the button reduces the image. To display a portion of the enlarged image which is outside of the display area, press the Enter button to
scroll the image. Power Turns the projector on or off. Effect buttons Use to display special effects that have been assigned
in the Effect menu. Enter Use the enter button to navigate the menus or use the
remote as a mouse pointer when the projector is
connected to the computer with the computer cable
and the mouse cable.
You can also select a menu option by pressing the
center of this button (Enter).
If you press the Enter when a menu or help is
displayed, you access the next menu or screen. When
the image source is a computer, the Enter button acts
as the mouse left click.
■ ■ ■ ■
36
Illumination button
Lights up all buttons on the remote control for 10
seconds. Esc Terminates the current function.
If you press the Esc button when a menu or help is
displayed, you go back to the previous screen or
menu.
When the image source is a computer, the Esc button
acts as the mouse right click. Menu Displays or hides the menu. Help Displays the Help menu.
Button Function
Comp Switches to the computer image from Computer. S-Video Switches to the video image from S-Video. Video Switches to the image from Video. Auto Optimizes the computer image. Resize Switches between the Window display and Resizing
display. P in P Displays a subscreen on the main display. To display
the subscreen, press the PinP button once. To hide
the subscreen, press it again.
To set the subscreen being displayed, press in the
following order :
[Menu] [Setting] [P in P].
The default settings are as follows;
Subscreen size:1/9 division
Main screen input source:Computer
Subscreen input source:Video
To change the subscreen position, press the Enter
button. The subscreen will move to the selected
direction. Volume +/- Adjusts the volume.
Controlling the Projector
■ ■ ■ ■ ■
37

Using the Operation Panel

Enter button
Power
Source
Enter
Keystone
Select
Operation Panel
Help
You can use the operation panel to control the projector instead of the remote control. However, you can program and access the custom features only using the remote control.
The following table summarizes the functions on the operation panel.
Button Function
Power Turns the projector on or off. Help Displays the Help menu. Source Switches the image source in order of computer
video
composite video. If there is no S-video input,
the switch toggles between computer and composite
video.
S-
■ ■ ■ ■
Enter Selects a menu option when the Help menu is
displayed. Keystone +/- Adjusts a trapezoid distorted image to normal. Select Scrolls up and down, or right and left when the Help
menu is displayed.
38

Projector Status Indicators

The power and lamp indicators at the top of the projector tell you its operating status.
Operation Indicator Lamp Indicator
Temperature Indicator
Caution:
A red indicator warns you if a serious problem occurs. See Chapter 5, “Troubleshooting,” for what to do if a warning light comes on.

Operation Indicator

Displays machine condition.
Color Status Meaning
Orange Lit Sleep mode. (The projector is plugged in,
Green Flashing The projector is warming up. Green Lit Power and projection lamp are on. Orange Flashing Projection lamp is off, and the projector is
Red Lit There is an internal projector problem and
- Off The projector is not on.
but not projecting.)
cooling down for one minute. Cooling time depends on the air temperature. During the cooling, any other operations cannot be executed.
the power to the projector has been cut off.
Projector Status Indicators
■ ■ ■ ■ ■
39

Lamp Indicator

Displays lamp condition. This indicator is off when the projector is in a normal
condition.
Color Status Meaning
- Off Lamp is functioning normally. Red Lit The lamp needs to be replaced. Orange Flashing Projection lamp has reached the time to
replace and will no longer project images. Replace the projection lamp with a new one.
Red Flashing There is a problem with the projection
lamp, lamp power supply, lamp fuse, or a circuit malfunctioned in the projector.

Temperature Indicator

Displays the internal temperature condition. This indicator is off when the projector is in a normal
condition.
■ ■ ■ ■
Color Status Meaning
- Off The projector is functioning normally. Orange Flashing The projector is too hot. Red Lit The projector has turned off automatically
because of over heating.
Red Flashing There is a problem with the cooling fan or
temperature sensor.
40
3

Using the Projector Menus

The eight projector menus let you to control your projector.
• The Video menu controls the look and quality of the
projected image, whether the image source is a computer or video.
• The Audio menu controls audio features, such as the
volume level, tone setting.
• The Effect menu lets you define functions for the Effects
buttons on the remote control.
• The Setting menu lets you select various projector options.
• The User’s Logo menu lets you select special features such
as background color or a custom logo.
• The Advanced menu enables you to set various projector
options.
• The About menu provides information about H/
V(Horizontal/Vertical) frequency, and lamp hours etc.
• The Reset All menu returns all settings to their factory
defaults.
■ ■ ■ ■ ■
41

Accessing the Main Menu

To display the Main menu, press the Menu button on the remote control. The Main menu appears:
Press the Menu button again to hide the menu.
■ ■ ■ ■
42

Changing a Menu Setting

To change a menu setting:
1. Press the Menu button on the remote control to display
the Main menu.
2. Press the top or bottom of the Enter button to scroll
through the menu choices.
Power
Freeze
A/V Mute
R/C ON
E-Zoom
OFF
3
4
2
5
1
Enter
Esc
Enter button
3. Press the Enter button to display a submenu.
Power
Power
Freeze
Freeze
A/V Mute
A/V Mute
R/C ON
R/C ON
E-Zoom
E-Zoom
OFF
OFF
3
3
4
4
2
2
5
5
1
1
Enter
Enter
Esc
Esc
Enter button
Changing a Menu Setting
■ ■ ■ ■ ■
43
As you select a menu, a sub menu of options appears to the right.
Note:
The options available in some submenus vary, depending on whether the current image source is the computer or a video source.
4. Press the top or bottom of the Enter button to scroll
through the menu choices.
5. Press the right or left sides of the Enter button to change a
setting on one of the submenus.
6. When you are finished changing settings, press the Menu
button again to hide the menu, or press the Esc to go back to the Main menu. Your changes are saved automatically.
■ ■ ■ ■
44

Menu Options

Video Menu (Image source = Computer)

The Video menu lets you make adjustments to the projected image. The following options are available when the image source is Computer.
Note:
The computer must be connected and operating, and the image source on the projector must be set to Computer for you to access these menu options.
Menu item Description
Position Select this item by pressing the Enter button to enter
the screen position adjustment mode. Then use the Enter button to move the screen position in the corresponding direction. When you finish making adjustment, press the Esc button to return to the Video submenu.
Tracking Matches the projector’s internal clock to various
computer graphic signals. Adjust this setting to remove vertical lines from the image.
Sync. Synchronizes with the tracking signal sent from the
computer. Adjust this setting to correct fuzziness or screen flicker.
Brightness Lightens or darkens the overall image. Increase
brightness to lighten an image, or decrease it to darken the image.
Contrast Adjusts the difference between light and dark areas.
Increase the contrast to make light areas lighter and dark areas darker. Decrease it to minimize the difference between light and dark areas.
Menu Options
■ ■ ■ ■ ■
45
Menu item Description
Color Adjusts the color balance (Red:Green:Blue) of the
input source. Select this item by pressing the Enter button. The projector will enter color adjustment mode. Use the Enter button to select a color. Next, use the Enter button to adjust the selected color. Increase the color setting for more intense color, or decrease the setting for less intense color.
Sharpness Adjusts the screen sharpness.
Increase the sharpness for a sharper image, or decrease it for a less sharp image.
Auto Setup Set to On to have the computer automatically optimize
the image for projection. Gamma Adjusts the projected imagery for natural coloration. Reset Returns all menu items to their initial factory defaults.
Select this item and then press the Enter button to
display the confirmation screen.
Next, select Yes and then press the Enter button to
reset the menu.
If you change your mind, select No and then press the
Enter button to clear the confirmation screen without
changing any settings.
■ ■ ■ ■
46

Video Menu (Image source = Video)

The Video menu lets you make adjustments to the projected image. The following options are available when the image source is Video.
Note:
The projector’s image source must be set to Video, and the video source (such as a VCR or camcorder) must be connected and operating for you to access these menu options (for example, the projector must actually be projecting an image from a video tape, if you’re using a VCR).
Menu item Description
Position Select this item by pressing the Enter button to enter
the screen position adjustment mode. Then use the Enter button to move the screen position in the corresponding direction. When you finish making adjustment, press the Esc button to return to the Video submenu.
Brightness Lightens or darkens the overall image. Increase
brightness to lighten an image, or decrease it to darken the image.
Contrast Adjusts the difference between light and dark areas.
Increase the contrast to make light areas lighter and dark areas darker. Decrease it to minimize the difference between light and dark areas.
Color Adjusts color density. Increase the setting for darker
and more opaque colors. Decrease it for lighter and less opaque colors.
Tint Adjusts the red-green color balance of the screen.
Increase tint to add more green, (NTSC only) or decrease it to add more red. This setting only works with NTSC video signals.
Sharpness Adjusts the screen sharpness.
Increase the sharpness to make screen images more sharp, or decrease it to make the images less sharp.
Gamma Adjusts the projected imagery for natural coloration.
Menu Options
■ ■ ■ ■ ■
47
Menu item Description
Mode Specifies the image signal mode. User can select from
Reset Returns all menu items to their initial factory defaults.

Audio Menu

The Audio menu lets you make adjustments related to audio.
Menu item Description
Volume Adjusts the volume level for the speakers and audio-
Tone Adjusts the sound quality. Reset Returns all menu items to their initial factory defaults.
Auto, NTSC, NTSC4.43, PAL, M-PAL, N-PAL, PAL 60, SECAM.
Select this item and then press the Enter button to display the confirmation screen. Next, select Yes and then press the Enter button to reset the menu. If you change your mind, select No and then press the Enter button to clear the confirmation screen without changing any settings.
out terminal.
Select this item and then press the Enter button to display the confirmation screen. Next, select Yes and then press the Enter button to reset the menu. If you change your mind, select No and then press the Enter button to clear the confirmation screen without changing any settings.
■ ■ ■ ■
48

Effect Menu

Use the Effect menu to modify what happens when you use the Effects buttons on the remote control and to change the cursor speed
Menu item Description
Cursor/Stamp Selects the stamp icon you want to use as the cursor
Box Selects the box color and shape. Marker Selects the marker color and width. Freehand Selects the color and width. Cursor Speed Selects the cursor speed to Low, Middle, or High. Reset Returns all menu items to their initial factory defaults.
.
graphic and a zoom rate.
Select this item and then press the Enter button to display the confirmation screen. Next, select Yes and then press the Enter button to reset the menu. If you change your mind, select No and then press the Enter button to clear the confirmation screen without changing any settings.

Setting Menu

The Setting menu lets you adjust or set the various projector options.
Menu item Description
Keystone Adjusts the trapezoid distorted image to normal. P-in-P Selects the image source (composite or S-Video) for
the subscreen.
Menu Options
■ ■ ■ ■ ■
49
Menu item Description
No-Signal Msg Specifies whether a black screen, a blue screen, or a
user logo displays when the screen is blanked.
Prompt Temporarily displays a message on the projector
screen to identify which source (computer or video) is providing the image.
A/V Mute Turns off/on the audio/video output of the projector,
clears all special effects, and displays a black, blue, or user logo screen.
Power Mgmt Sys You can select to turn off or keep the lamp power on
when there is no input source.
Reset Returns all menu items to their initial factory defaults.
Select this item and then press the Enter button to display the confirmation screen. Next, select Yes and then press the Enter button to reset the menu. If you change your mind, select No and then press the Enter button to clear the confirmation screen without changing any settings.

User's Logo Menu

■ ■ ■ ■
The User’s Logo menu lets you display a custom logo on the screen.
Creating a user logo requires two steps:
• Storing a user logo
• Assigning the logo to the A/V Mute button
50
Storing a User Logo
Follow these steps to capture and store a logo.
1. Display the image(with the projector) you wish to use as a
logo.
2. Press the Menu button to open the Menu window.
3. Select the User’s Logo menu option by pressing the
pointer button. Then press the Enter button to display the User’s Logo Setting window.
4. The message, “Do you use the present image as a user
logo?” appears on the screen. Choose Yes or No by pressing left or right of the Enter button. Then press Enter button.
5. When you choose “Yes” in the step 4, a selection box will
appear over the image. To select the portion of the image you wish to use as the logo, use the Enter button. Once you have selected the desired area, press the Enter button.
6. The message “Do you use this image?” appears on the
screen. Select Yes and press the Enter button. If you want to change the position, select No.
7. Next, the Zoom rate setting window appears on the
screen. Select a rate using the arrow buttons, then press the Enter button.
8. The message “Do you save this user logo?” appears on the
screen. Select Yes and press the Enter button. If you don’t want to save the logo, select No.
Note:
Saving the logo may take a moment. Do not use the projector or other sources (computer, video, speaker, etc.) while the logo is being saved.
9. When the message “Saving the user logo is completed”
appears on the screen, press the Menu or Enter button to display the Main Menu.
Menu Options
■ ■ ■ ■ ■
51
Assigning the Logo to the A/V Mute Button
Follow these steps to assign the logo to the A/V Mute button:
1. Press the Menu button to open the Menu window.
2. Select the Setting menu and press the Enter button.
3. Select the Blank option (A/V Mute), then highlight User
Logo.
4. Press the Menu button twice. Now you can press the A/V Mute button on the remote
control to display the user logo.

Reset All Menu

Selecting the Reset All menu option resets the settings in all menus to their factory defaults. It does not change or delete any user logo you may have stored.
You will be prompted to confirm the reset action. Select Yes or No, then press the Enter button to reset all the settings.
■ ■ ■ ■
52

Advanced Menu

The Advanced menu enables you to set various projector options.
Menu item Description
Language Selects the menu language from Japanese, English,
German, French, Italian, Spanish, Portuguese, Chinese and Korean.
Startup Screen Displays the user logo during the warm-up after the
projector is turned on.
Color Temp. Adjusts the whiteness and blackness of the screen.
Increasing the values emphasizes the whiteness and blackness. Decreasing the values weakens the whiteness and blackness.
Rear Proj. Mirrors the projected image so it looks correct when
you’re projecting from behind onto a translucent screen. Selecting ON turns mirroring on, while OFF turns it off (for a normal image).
Ceiling Flips the projected image so it looks correct when
you’re hanging the projector upside-down from the ceiling. Selecting ON turns this feature on, while OFF turns it off (for a normal image).
Reset Returns all menu items to their initial factory defaults.
Select this item and then press the Enter button to display the confirmation screen. Next, select Yes and then press the Enter button to reset the menu. If you change your mind, select No and then press the Enter button to clear the confirmation screen without changing any settings.
Menu Options
■ ■ ■ ■ ■
53

About Menu

The About menu displays the following information about your projector.
Image source = Computer or Component Video
Menu item Description
Lamp Displays the number of hours the current lamp has
Frequency Displays the horizontal and vertical frequency of the
SYNC Polarity Displays the sync polarity of the computer. SYNC Mode Displays the sync mode of the computer. Resolution Displays the output resolution of the computer video
Refresh Rate Displays the refresh rate of the computer video output.
Image source = Video
been used. The lamp light turns red when the projector lamp needs to be replaced. When this happens, replace the projector lamp with a new one as soon as possible.
computer.
output.
■ ■ ■ ■
Menu item Description
Lamp Displays the number of hours the current lamp has
been used. The lamp light turns red when the projector lamp needs to be replaced. When this happens, replace the projector lamp with a new one as soon as possible.
Video Signal Displays the input image signal mode.
54
4

Maintenance

Your projector needs little maintenance. You should keep the
lens clean because any dirt or smears appear on the screen. You also need to periodically clean the air filter. A clogged air filter can block ventilation needed to cool the projector and keep it from overheating.
The only parts you should replace are the lamp and air filter. If any other part needs replacing, contact your dealer or a qualified service person.
projector and unplug the power cord. Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages in the projector can injure you severely. Do not try to service this product yourself, except as specifically explained in this User’s Guide. Refer all other servicing to qualified service personnel.
Before you clean any part of the projector, turn off the
■ ■ ■ ■ ■
55

Cleaning the Lens

Clean the lens whenever you notice dirt or dust on the surface. Lightly wipe the lens surface with a soft, dry, lint-free cloth.
To remove dirt or smears on the lens, moisten a soft cloth with an alcohol-based cleaner and gently wipe the lens surface.

Cleaning the Projector Case

To clean the projector case, first unplug the power cable. To remove dirt or dust, wipe the case with a soft, dry, lint-free cloth. To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral detergent. Then wipe the case.
Do not use alcohol, benzene, thinners or other chemical detergents. These can cause the case to warp.
■ ■ ■ ■
56

Cleaning the Air Filter

Clean the air filter at the top of the projector after every 100 hours of use. If it is not cleaned periodically, it can become clogged with dust, preventing proper ventilation. This can cause overheating and damage the projector. To clean the air filter, follow these steps:
1. Turn off the projector and unplug the power cable.
2. Stand the projector with the lens at the top.
Note:
Standing the projector with the lens at the top keeps dust from getting inside the projector housing.
3. Use a small vacuum cleaner designed for computers and
other office equipment to clean the filter. If the dirt is difficult to remove or if the filter is torn,
replace it. Contact your dealer or call EPSON Service Center.
Cleaning the Air Filter
■ ■ ■ ■ ■
57

Replacing the Lamp

Replace the lamp when:
• The projected image gets darker or starts to deteriorate.
• The projection lamp indicator is flashing orange .
• The message “LAMP REPLACE” appears on the screen
when the projector lamp comes on.
Note:
To keep the initial brightness and image quality, replace the lamp as soon as possible when the message appears on the screen. The replacement message is set to being displayed at about 2000 hours of use. Contact your local EPSON dealer for a spare lamp. Request part number ELPLP10B (EMP-700/500) or ELPLP10S (EMP-710).
touch the glass portion of the lamp assembly. Touching the glass portion of the lamp will result in premature lamp failure.
1. Turn off the power and allow the unit to cool down, then
remove the power cord. The amount of time needed to cool down will depend on the ambient temperature.
Let the lamp cool before replacing it. Also, do not
■ ■ ■ ■
58
2. Remove the lamp cover after the unit is cool. It will
normally take about an hour to completely cool down. Loosen a lamp cover-mounting screw with the screwdriver provided with the spare lamp, then remove.
Screwdriver
3. Loosen two mounting screws for the lamp with the same
screwdriver, and pull out the lamp using the handle.
4. Mount new lamp. Check that the lamp orientation is
correct, and then press it into place securely. Tighten the mounting screws for the lamp with the screwdriver.
5. Remount the lamp cover.
Tighten the lamp cover screw with the screwdriver.
Replacing the Lamp
■ ■ ■ ■ ■
59
■ ■ ■ ■
60
5

Troubleshooting

This chapter describes the problems indicated by the warning
lights and provides information on how to solve problems with the projector. It is divided into the following sections:
• Problems with the projector. See this section if the
projector is not working and to find out what the warning lights are indicating.
• Problems with the screen image. See this section if you
cannot project an image or if the screen image is poor.
If you have a problem, refer to the appropriate section and follow all suggestions that apply to your problem. If none of the suggested solutions solves the problem, call your dealer or EPSON Service Centre.
■ ■ ■ ■ ■
61

Problems with the Projector

If you have problems with the projector, first turn it off and unplug it. Then plug the power cord back in and turn on the projector. If this does not solve the problem, check the warning lights at the top of the projector. These lights alert you to problems with projector operation.
See the following pages for information on what to do when you see these warning lights or encounter other specific problems with the projector.
The operation indicator is flashing orange and you
cannot turn on the projector.
Operation Indicator
Lamp Indicator
Temperature Indicator
■ ■ ■ ■
The lamp is cooling down. Wait until the light turns off and then turn on the projector.
The operation indicator does not come on.
Turn off the projector, check that the power cable is connected securely both at the power outlet and the projector, and press the Power button again.
Projected images get darker or start to deteriorate,
or the lamp indicator is red.
Replace the projector lamp as described on page 58.
62
The temperature indicator is red.
The projector is overheating, which turns the lamp off automatically. Let the projector cool for a few minutes, then turn it back on. Make sure nothing is blocking the ventilation vents.
The air filter may be clogged. Clean it as described on page 57 in Chapter 4 and then let the projector cool for a while.
If the projector continues to overheat after you clean the air filter, the problem may be caused by damage to the cooling fan or internal circuits. Contact a qualified service person.
Do not attempt to service this product yourself except
as specifically explained in this User’s Guide.
Problems with the Projector
■ ■ ■ ■ ■
63

Problems with the Image or Sound

An image does not appear on the screen.
Check that the power light is on and the lens cover is off. Also make sure the cables are installed correctly, as described in Chapter 1.
The correct image source may not be selected. Press the Source button on the remote control or the Source button on the appropriate input operation panel to choose another image source.
Only part of the computer image is displayed.
If the computer’s output resolution setting is higher than 1024 × 768 (EMP-710/700) or 800 x 600 (EMP-500), the projector resizes the image. If the computer output is not compatible with this resizing, choose a different display setting on the computer. For supported display settings, see “Supported Monitor Displays” on page 69, 70.
You also may need to modify existing presentation files if you created them for a different resolution. See your software manual for specific information.
■ ■ ■ ■
The message NO SIGNAL is displayed.
An image source not connected to the projector is selected, the signal is not being output from the computer, or the signal is not reaching the projector. Make sure the connectors are securely attached to both the projector and the image source. Then check that the image source is selected correctly. When NO SIGNAL is displayed, you cannot access the Video (computer/video) menu.
64
A blank screen is displayed.
The computer signal cannot be interpreted by the projector. Verify the display format (see page 69, 70). When you see a blank screen, you cannot access the projector menus.
The image or parts of the image are blurred or not
in focus.
Adjust the Brightness and Contrast settings on the Video menu. If you’re viewing a computer image, also try adjusting the Tracking and Sync buttons on the projector’s operation panel.
There may be dirt or smears on the lens. Clean the lens as described in Chapter 4, “Maintenance.”
The colors of the image are not right.
The color balance may be incorrect. If you’re displaying a computer image, adjust the red, green, and blue settings in the Video menu. If you’re displaying video, adjust the Color and Tint (NTSC only) settings on the Video menu.
There is no sound.
First check that the volume setting is not turned all the way down and that the RCA audio cable is securely attached to both the projector and the audio source. Also, make sure that the Mute button is off.
The wrong source is selected. Press either the Computer or Video button on the remote control or Source button on the operation panel to select the proper source.
Problems with the Image or Sound
■ ■ ■ ■ ■
65
■ ■ ■ ■
66
6
Technical Specifications
General
Type of display Poly-silicon TFT Size of liquid crystal panels 0.9 inches (22.9 mm) Resolution
Projection distance 26-300 inch (1.1-13.8 meters) Remote control range 32.8 feet (10 meters) Internal speaker system 1W Monaural Optical aspect ratio 4 : 3 (horizontal : vertical)
1024 (horizontal) x 768 (vertical) pixels (EMP-710/700) 800 (horizontal) x 600 (vertical) pixels (EMP-500)
Zoom ratio 1:1.2
Projector Lamp
Type UHE Lamp (Ultra High Efficiency Lamp) Power 120 W Part number ELPLP10S (EMP-710)
ELPLP10B (EMP-700/500)
■ ■ ■ ■ ■
67
Mechanical
Height 7.4 inches (87 mm)
Maximum dimension
Width 19.8 inches (267 mm)
Maximum dimension
Depth 12 inches (213 mm)
Maximum dimension
Weight 5.8 lb (2.6 kg)
Electrical
Voltage 100 - 120 V
AC and 200 - 240 VAC ± 10%
Rated frequency 50/60 Hz Power supply 100 - 120 V
200 - 240 V
AC, 1.9 A, 50/60 Hz AC, 1.0 A, 50/60 Hz
Environmental
■ ■ ■ ■
Technical Specifications
68
Temperature
Operation: 41 - 95˚ F (5 - 35˚ C), non-condensing
Storage: 14 - 140˚ F (-10 - 60˚ C), non-condensing
Humidity Operation: 20 - 80% RH,
non-condensing Storage: 10 - 90% RH,
non-condensing

Supported Monitor Displays

The projector displays images at a resolution of 1024 x 768 (EMP-710/700) or 800 x 600 (EMP-500) pixels. To display a higher resolution image, the projector compresses it to 1024 x 768 (EMP-710/700) or 800 x 600 (EMP-500). The following table lists the display formats supported by the projector:
Mode ACTIVE FREQUENCY MODEL
H V H(KHz) V(Hz) Pixel(MHz) EMP-710/
VGACGA 640 400 31.46 70 25.175 A/B A/B VGAEGA 640 350 31.46 70 25.175 A/B A/B
NEC400 640 400 24.83 56.65 21.053 A/B A/B
VGA60 640 480 31.469 59.94 25.175 A/B A/B VGA72 640 480 37.861 72.809 31.5 A/B A/B VGA75 640 480 37.5 75 31.5 A/B A/B
VGA85 640 480 48.269 85.008 36 A/B A/B SVGA56 800 600 35.156 56.25 36 A/B B SVGA60 800 600 37.879 60.317 40 A/B B SVGA72 800 600 48.077 72.188 50 A/B B SVGA75 800 600 46.875 75 49.5 A/B B SVGA85 800 600 53.674 85.061 56.25 A/B B
XGA43i 1024 768 35.522 86.958 44.9 B A
XGA60 1024 768 48.363 60.004 65 B A
XGA70 1024 768 56.476 70.069 75 B A
XGA75 1024 768 60.023 75.029 78.75 B A
XGA85 1024 768 68.677 84.997 94.5 B A
SXGA1_70 1152 864 63.851 70.012 94.5 A A SXGA1_75 1152 864 67.5 75 108 A A SXGA1_85 1152 864 77.094 84.999 121.5 A A
SXGA2-60 1280 960 60 60 108 A A SXGA2-75 1280 960 75 75 126 A A
A: Resize B: Native
EMP-500
700
Supported Monitor Displays
■ ■ ■ ■ ■
69
A: Resize B: Native
Mode ACTIVE FREQUENCY MODEL
H V H(KHz) V(Hz) Pixel(MHz) EMP-710/
SXGA2-85 1280 960 85.938 85.002 148.5 A A
SXGA3_43i 1280 1024 46.433 86.871 78.75 A A
SXGA3_60 1280 1024 63.981 60.02 108 A A SXGA3_75 1280 1024 79.976 75.025 135 A A SXGA3_85 1280 1024 91.146 85.024 157.5 A A
UXGA48i 1600 1200 62.5 96.08 135 A -
UXGA60 1600 1200 75 60 162 A -
MACLC13 640 480 34.975 66.62 31.33 A/B A/B
MAC ll 13 640 480 35 66.67 30.24 A/B A/B
MAC16 832 624 49.725 74.55 57.28 A/B A
MAC19-60 1024 768 48.193 59.28 64 B A
MAC19 1024 768 60.241 74.93 80 B A MAC21 1152 870 68.682 75.062 100 A A
NTSC 1024 480 15.734 60 - A A
PAL 1024 576 15.625 50 - A A
SECAM 1024 576 15.625 50 - A A
Note:
The frequencies of some computers may not allow the
700
image to be display correctly.
EMP-500
■ ■ ■ ■
Technical Specifications
70

Computer In connector pin assignments

The Computer In connectors are female video RGB, 15-pin micro-D-style connector. The pin assignments are:
Input pin Signal 1 Red analogue input 2 Green analogue input 3 Blue analogue input 4 GND 5 GND 6 Red GND 7 Green GND 8 Blue GND 9 Reserved 10 Sync GND 11 GND 12 SDA 13 Horizontal sync/composite sync input 14 Vertical sync input 15 SCL
Computer In connector pin assignments
■ ■ ■ ■ ■
71
DECLARATION of CONFORMITY/DICHIARAZIONE di
CONFORMITÀ/KONFORMITÄUNG/DECLARACIÓN de
CONFORMIDAD/DECLARATION de CONFORMITE
according to ISO/IEC Guide 22 and EN 45014/secondo la Guida ISO/IEC 22 e EN
450014/entsprechend ISO/CEI Anleitung 22 und EN 45014/De acuerdo con ISO/IEC
Guide 22 y EN 45014/selon les normes ISO/IEC Guide 22 et EN45014
Conforms to the following directives and Norms/Conforme alle seguenti direttive e Norme/Erfüllt die folgenden Direktiven und Normen/De acuerdo con las directrices y normas siguientes/ Conforme aux directives et normes suivantes
Directive 89/336/EEC
:EN 55022 Class B
:EN 50082-1
Directive 73/23/EEC
:EN 60950
■ ■ ■ ■
Technical Specifications
72

Glossary

Brightness. The balance of light and dark shades in an image.
Composite video. A type of video signal that encodes colours, luminance and sychronization information so it can be carried in one signal.
Contrast. A measure of the luminance differences between the highlights and shadows of an image. In a high-contrast image, light areas are very bright and dark areas are very dark.
NTSC. A 525-line video broadcast format developed by the National Television Standards Committee. NTSC is widely used in North America, Mexico and Japan.
PAL (Phase Alternation by Line). A 625-line video broadcast format used in Western Europe, India, China, Australia, New Zealand and parts of Africa.
Resolution. A measure of the amount of detail contained in an image. Resolution can be measured in dots per inch or in pixels. Image sharpness and clarity improve as resolution increases.
RGB. Red Green Blue S-Video. A type of video signal which transmits luminance
and colour separately.
SECAM (Système Electronique pour Couleur Avec Mémoire). A 625-line TV system used in France, Eastern
Europe, Russia and parts of Africa.
■ ■ ■ ■ ■
73
Serial. A type of communication interface that transmits data over a single wire.
■ ■ ■ ■
74
Glossary
F
Format 69

Index

A
Audio cable 9 Audio In jack 9 Audio Menu 48 Audio Out jack 25
B
Brightness 73
C
Cleaning the Air Filter 57 Color 47 Contrast 73 cooling 62
D
DAR viii
E
Effect Menu 49 External Speaker 1, 25
G
Glossary 73
I
Image 64 Installation x
M
Mac mouse cable 2, 15 Macintosh desktop adapter 13, 17 Maintenance x Mouse/Com port 8, 11, 15
N
NTSC 73
O
operation indicator 28 operation panel 28 Optional Accessories ix
P
PA System 1, 25 PAL 73
■ ■ ■ ■ ■
75
pin assignments 71 Power cord 2 Projector ix PS/2 mouse cable 2, 8
video-out cable 17 Volume 48
W
R
RCA audio cable 23 RCA video cable 23 Resolution 64, 73 RGB 73
S
SECAM 73 Serial 74 Setting Menu 49 Sound 64 stereo audio cable 25 S-Video 73 S-Video cable 24 S-Video connector 24
T
Technical Specifications x, 67 Tone 48 Troubleshooting x, 61
wireless mouse 1 World Wide Web xiii
■ ■ ■ ■
U
USB mouse cable 2 User's Logo Menu 50
V
Video Source 22
Index
76

W orld-Wide Warranty T erms

The EPSON Multi-Media Projector you purchased includes Epson’s World-Wide Warranty, which allows you to obtain repair service for your product outside the country where you purchased it in over 45 countries in the world. Please note that the terms stated in the warranty card which accompanied your product, and not these world-wide terms, will apply to service sought in the country or countries covered by the card.
This warranty service is limited to the following countries.
<EUROPE> AUSTRIA, BELGIUM, BULGARIA, CROATIA, CYPRUS, CZECH,
DENMARK, FINLAND, FRANCE, GERMANY, GREECE, HUNGARY, IRELAND, ITALY, LUXEMBURG, MACEDONIA, NETHERLANDS, NORWAY, PORTUGAL, POLAND, ROMANIA, SLOVAKIA, SLOVENIA, SPAIN, SWEDEN, SWITZERLAND, TURKEY, UNITED KINGDOM and YUGOSLAVIA
<NORTH, CENTRAL AMERICA & CARIBBEAN ISLANDS> CANADA, COSTA RICA, MEXICO and U. S. A. <SOUTH AMERICA> ARGENTINA, BRAZIL, CHILE, COLOMBIA, PERU and
VENEZUELA <ASIA & OCEANIA> AUSTRALIA, HONG KONG, JAPAN, KOREA, MALAYSIA,
SINGAPORE and TAIWAN
This warranty service is subject to the following terms and conditions.
1) To obtain warranty service, you must present proof of the date you purchased your product, by showing the servicer either your purchase receipt or your warranty card (if the purchase date is shown on the card).
■ ■ ■ ■ ■
77
2) This warranty service will be implemented based on the warranty term and conditions that have been established by EPSON (or its authorized servicer) in the country where service is sought. However, Epson guarantees at least these service terms:
- The period of warranty is 12 months from the day of purchase.
- The warranty will cover at least the cost of parts and labor.
- Epson cannot guarantee that the servicer will be able to provide
you with a replacement product while your product is being repaired.
3) This warranty service will not apply in to the following cases: a.Failures or defects in consumables such as Lamps or optional
equipment
b.In case the product was damaged due to inappropriate use or
failure to properly use in accordance with details of this manual, or transportation
c.In case the product was repaired or modified by any party other
than EPSON or an Epson-authorized servicer
d.Problems caused by optional equipment or consumables, other
than original EPSON product or product of the same quality
■ ■ ■ ■
Notice:
The power supply cable packed with your projector is subject to the power supply condition of the country where you purchased. When using your projector in foreign countries, make sure to purchase the original EPSON power supply cable produced for each country.
SERVICE CONTACTS FOR THE EPSON WORLD WIDE WARRANTY ON PROJECTORS
This contact list is current as of 21st June, 1999. For the latest contact information, please refer to the Web home page
noted for the relevant country, or, if none is listed, refer to Epson’s main Web page at www.epson.com.
World-Wide Warranty Terms
78
<EUROPE>
AUSTRIA : EPSON Support Center Austria Tech. Help Desk: 07110 900112 Web Address: http://www.epson.at
CYPRUS : CTC- INFOCOM 6a. lonos Str., Engomi P. O. Box 1744 2406 Nicosia, Cyprus Tel: 00357.2.458477 Fax: 00357.2.668490
BELGIUM : EPSON Support Center BeNeLux Tech. Help Desk: 070 222082 Web Address: http://www.epson.be
BULGARIA : PROSOFT
6. AI Jendov Str. BG-1113 Sofia Tel: 00359.2.730.231 Fax: 00359.2.9711049 E-mail: Prosoft@internet-BG.BG
CROATIA : Recro d.d. Trg. Sportova 11 HR-10000 Zagreb Tel: 00385.1.6350.777 Fax: 00385.1.6350.716 E-mail: recro@recro.hr Web Address: http://www.recro.hr
CZECH : EPRINT s.r.o. Stresovicka 49 CZ-16200 Praha 6 Tel: 00420.2.20180610 Fax: 00420.2.20180611 E-mail: eprint@mbox.vol.cz
DENMARK : Tech. Help Desk: 80881127
FINLAND : Tech. Help Desk: 0800.523010 (note. Some geographical areas excluded)
■ ■ ■ ■ ■
79
FRANCE : EPSON France, 68 bis rue Marjolin, F-92300 Levallois, Tech. Help Desk:
01.49.61.33.95 Web Address: http://www.epson.fr
IRELAND : Tech. Help Desk: 01.6799016
GERMANY : EPSON Deutschland GmbH Zülpicher Straße 6 40549 Düsseldorf Tech. Help Desk: 01805235470 Web Address: http://www.epson.de
GREECE : Pouliadis Ass. Corp. Aristotelous St. 3 GR-19674 Athens Tel: 0030.1.9242072 Fax: 0030.1.9441066
HUNGARY : R.A. Trade Kft. Petöfi Sandor u. 64 H-2040 Budaör Tel: 0036.23.415.317 Fax: 0036.23.417.310
ITALY : EPSON Italia s.p.a. Assistenza e Servizio Clienti Viale F. Lli Cashiragi, 427 20099 Sesto San Giovanni (MI) Tech. Help Desk: 02.29400341 Web Address: http://www.epson.it
LUXEMBURG : EPSON Support Center BeNeLux Tech. Help Desk: 0032 70 222082 Web Address: http://www.epson.be
MACEDONIA : Rema Kompjuteri d.o.o. St. Naroden Front 19a lok 16 91000 Skopje/ Macedonia Tel: 00389.91.118159 Fax: 00389.91.118159
■ ■ ■ ■
World-Wide Warranty Terms
80
NETHERLANDS : EPSON Support Center BeNeLux Tech. Help Desk: 043 3515752 Web Address: http://www.epson.nl
ROMANIA : MB Distribution S.R. L. 162, Barbu Vacarescu Blvd. Sector 2 RO- 71422 Bucharest Tel: 0040.1.2300314 Fax: 0040.1.2300313 E-mail: office@mbd-epson.ro
NORWAY : Tech. Help Desk: 800.11828
PORTUGAL : EPSON Portugal, S.A. Rua do Progresso, 471-1 Perafita- Apartado 5132 Tech. Help Desk: 0808 200015 Web Address: http://www.epson.pt
POLAND : FOR EVER Sp. z.o.o. Ul. Frankciska Kawy 44 PL- 01-496 Warszawa Tel: 0048.22.638.9782 Fax: 0048.22.638.9786 E-mail: office@for-ever.com.pl
SLOVAKIA : Print Trade spol. s.r.o. Cajkovskeho 8 SK-98401 Lucenec Tel: 00421.863.4331517 Fax: 00421.863.4325656 E-mail: Prntrd@lc.psg.SK Web Address: http://www.printtrade.sk
SLOVENIA : Repro Ljubljana d.o.o. Smartinska 106 SLO-1001 Ljubljana Tel: 00386.61.1853411 Fax: 00386.61.1400126
SPAIN : EPSON IBERICA, S.A. Avda. Roma 18-26, E-08290 Cerdanyola, Barcelona, SPAIN Tech. Help Desk: 902.404142 E-mail: soporte@epson.es Web Address: http://www.epson.es
■ ■ ■ ■ ■
81
SWEDEN : Tech. Help Desk: 08 445 1258
UNITED KINGDOM : EPSON (UK) Ltd. Campus 100, Maylands Avenue Hemel Hempstead, Herts, HP2 7TJ Tech. Help Desk: 0990 133640 Web Address: http://www.epson.uk
SWITZERLAND : EXCOM Service AG Moosacher Str. 6 CH-8820 Wädenswil Tel: 01.7822111 Fax: 01.7822349 Web Address: http://www.excom.ch
TURKEY : Romar Pazarlama Sanayi ve TIC. A.S. Rihtim Cad. No. 201 Tahir Han TR-Karaköy-Istanbul Tel: 0090.212.2520809 Fax: 0090.212.2580804
YUGOSLAVIA : BS Procesor d.o.o. Hadzi Nikole Zivkovica 2 11000 Beograd Tel: 00381.11.639610 Fax: 00381.11.639610
■ ■ ■ ■
World-Wide Warranty Terms
82
Loading...