Epson 700C, 710C, 500C User Manual

EPSON® PowerLite® 500c/700c/710c
Multimedia Projector
User’s Guide
Supplement
Important Safety Information
WARNING
Never let children look into the lens when it is on. Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages inside the projector can severely injure you. Except as specifically explained in the User’s Guide or this Supplement, do not attempt to service this product yourself. Refer all
: Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes.
2
C
Connecting to a
A
Desktop Computer

Contents

Positioning the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Identifying the Projector Ports . . . . . . . . . . . . . . . . . . . . . . . . 7
Connecting to a PC Desktop Computer . . . . . . . . . . . . . . . . 7
Connecting the Computer Cable . . . . . . . . . . . . . . . . . . 8
Connecting the Audio Cable . . . . . . . . . . . . . . . . . . . . . . 9
Connecting the Cable for Remote Mouse Control . . . . . 9
Connecting to a Desktop Macintosh . . . . . . . . . . . . . . . . . . 10
Connecting the Computer Cable . . . . . . . . . . . . . . . . . 11
Connecting the Audio Cable . . . . . . . . . . . . . . . . . . . . . 13
Connecting the Cable for Remote Mouse Control . . . . 13
Turning the Projector On and Off . . . . . . . . . . . . . . . . . . . 14
Turning On Other Equipment . . . . . . . . . . . . . . . . . . . 16
Using the
B
Projector Menus
Changing Menu Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Video Menu (Computer Image Source) . . . . . . . . . . . . . . . . 20
Video Menu (Video Image Source) . . . . . . . . . . . . . . . . . . . 22
Audio Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Effect Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Setting Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
User’s Logo Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Capturing the Image . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Assigning the Image to the No-Signal Message
and/or A/V Mute Button . . . . . . . . . . . . . . . . . . . . 29
Advanced Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
About Menu (Computer Image Source) . . . . . . . . . . . . . . . 31
About Menu (Video Image Source) . . . . . . . . . . . . . . . . . . . 32
Reset All Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
3
Technical
C
Specifications
Index
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Projection Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Mouse Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Remote IR Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Mechanical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
CE Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Supported Monitor Displays . . . . . . . . . . . . . . . . . . . . . . . . 35
Computer Connector Pin Assignments . . . . . . . . . . . . . . . . 37
4
Appendix A: Connecting to a Desktop Computer
A
note
For instructions on connecting to a laptop computer or to external speakers, see your User’s Guide.
This appendix describes how to connect the projector to your desktop computer and turn everything on. The projector must be connected to a computer or a video source such as a VCR, camcorder, digital camera, DVD player, or laser disc player before it can project any images. You may also want to set up the projector for one or more of the following:
Connect the mouse cable to use the remote control as a
wireless mouse. Except for some laptops, this disables your computer’s mouse. You use the remote control’s pointer to control the screen cursor.
Provide audio for one or both image sources. The audio
source can be the computer, video source, or another device such as a stereo.
Connect to an external speaker or PA system to amplify the
audio (see your User’s Guide for instructions).

Positioning the Projector

Before you can set up the projector, you need to decide where to place it. Keep the following in mind:
Place the projector on a sturdy, level surface.
Make sure the projector is within 10 feet of a grounded
electrical outlet or extension cord.
Place the computer and/or video source within 5 feet of the
projector.
Make sure the projector is at right angles to the screen.
Otherwise, your image will be distorted.
Connecting to a Desktop Computer 5
note
It is easier to position the projector when the screen is directly in front of the room. If the screen is placed diagonally in a corner, it is much more difficult to position the projector perpendicular to the screen and get a non-distorted image.
Most presenters find it convenient to place the projector (and computer) in the front of the room. With this arrangement, the projector is placed close to the screen. You need to raise the front of the projector (by extending the legs) in order to position the image high enough on the screen. Then you can use the projector’s keystone control to correct the distortion caused by tilting up the front of the projector.
The distance between the projector and the screen determines the actual image size. Use the general guidelines in the table below to determine the proper distance.
Horizontal distance from projector to screen
Image size
(diagonal)
2.2 feet (0.7 meter) 3.6 feet (1.1 meters)
2.5 feet (0.8 meter) 3.6 feet (1.1 meters) 4.3 feet (1.3 meter)
3.3 feet (1.0 meter) 4.8 feet (1.5 meters) 5.6 feet (1.7 meters)
5.0 feet (1.5 meters) 7.5 feet (2.3 meters) 8.9 feet (2.7 meters)
6.7 feet (2.0 meters) 9.8 feet (3.0 meters) 11.8 feet (3.6 meters)
8.3 feet (2.5 meters) 12.5 feet (3.8 meters) 14.8 feet (4.5 meters)
12.5 feet (3.8 meters) 18.7 feet (5.7 meters) 22.6 feet (6.9 meters)
16.7 feet (5.1 meters) 25.3 feet (7.7 meters) 30.2 feet (9.2 meters)
25 feet (7.6 meters) 37.7 feet
Minimum (lens set to W)
(11.5 meters)
Maximum (lens set to T)
45.3 feet (13.8 meters)
6 Connecting to a Desktop Computer

Identifying the Projector Ports

The following illustrations identify all the interface ports on the back and side of the projector; you may want to refer to them as you connect your computer or other equipment to the projector.

Connecting to a PC Desktop Computer

To connect the projector to your PC desktop computer, you need to:
Connect the computer cable
Connect the audio cable (if you’ll be projecting with audio)
Connect the mouse cable (if you want to use the remote
control as a mouse)
If you connect the projector to your desktop computer, you cannot view your images on the computer monitor.
Follow the steps in each section for the cables you need to connect.
Connecting to a Desktop Computer 7
note
If you need maximum volume (in a large auditorium, for example), you can also connect external speakers or a public address system to the projector. See your User’s Guide for instructions.

Connecting the Audio Cable

If your presentation includes sound effects or other types of computer audio, you need to connect the audio cable.
1. Connect one end of the audio cable to the
the projector.
Audio in jack
2. Connect the other end of the audio cable to the speaker or
audio out port on your computer’s sound card.
Audio In jack on
audio cable

Connecting the Cable for Remote Mouse Control

Using the remote control as a wireless mouse gives you more flexibility. You can deliver your presentation from anywhere in the room and interact with the audience. You don’t need to stand near your computer or near the projector.
You’ll use different cables and different ports on the projector, depending on whether your computer has a round PS/2 mouse port or a flat USB mouse port.
Mouse/Com
PS/2 mouse port
USB Mouse
USB mouse port USB mouse cable
Connecting to a Desktop Computer 9
PS/2 mouse cable
1. Determine which type of mouse port your computer has:
Round PS/2 mouse port
Flat USB mouse port
2. Connect one end of the appropriate mouse cable to the
Mouse/Com port or the USB Mouse port on the
PS/2 projector.
connecting PS/2 mouse cable connecting USB mouse cable
3. Connect the other end to the mouse port on your
computer. (Your computer’s mouse will be disabled while you are using the remote control as a mouse.)

Connecting to a Desktop Macintosh

note
Macintosh configurations vary. See your computer manual for the location of the ports needed to connect your projector.
To connect the projector to your desktop Macintosh,® you need to:
Connect the computer cable
Connect the audio cable (if you’ll be projecting with audio)
Connect the mouse cable (if you want to use the remote
control as a mouse)
If you connect the projector to your Macintosh, you cannot view your images on the computer monitor.
Follow the steps in each section for the cables you need to connect.
10 Connecting to a Desktop Computer
note
If you have an older Macintosh, you may need to use a Macintosh adapter (available from Apple Check the documentation for your Macintosh to determine what type of connections are available.
®
).

Connecting the Computer Cable

Before you start, make sure your projector, computer, and all peripherals are all turned off.
1. Disconnect the monitor cable from the monitor port on the
back of your Macintosh.
2. Connect one end of the computer cable to the projector’s
Computer port.
3. Connect the other end to the monitor port on your
Macintosh.
Connecting to a Desktop Computer 11
If you can’t connect the projector’s computer cable to your Macintosh, you may need to use a Macintosh adapter (available from Apple).
Remove the small cover on the
Macintosh adapter and set its DIP switches according to the resolution you want to use (such as 16-inch mode). See your Macintosh documentation for instructions.
Connect the small end
of the Macintosh adapter to the computer cable.
Connect the computer
cable (with the Macintosh adapter attached) to the monitor port on your Macintosh.
4. Tighten the screws on all the connectors.
If you don’t need to make any other connections, you can plug in your projector and turn it on. See page 14 for instructions.
12 Connecting to a Desktop Computer
note
If you need maximum volume (in a large auditorium, for example), you can also connect external speakers or a public address system to the projector. See your User’s Guide for instructions.

Connecting the Audio Cable

If your presentation includes sound effects or other types of computer audio, you need to connect the audio cable.
1. Connect one end of the audio cable to the
the projector.
Audio in jack
audio cable
2. Connect the other end of the audio cable to the speaker
jack on your Macintosh.
Audio In jack on

Connecting the Cable for Remote Mouse Control

Using the remote control as a wireless mouse gives you more flexibility. You can deliver your presentation from anywhere in the room and interact with the audience. You don’t need to stand near your Macintosh or near the projector.
You’ll use different cables and different ports on the projector, depending on what type of mouse your Macintosh has.
Mouse/Com
standard mouse port
USB Mouse
USB mouse port USB mouse cable
Connecting to a Desktop Computer 13
Mac mouse cable
1. Determine which type of mouse port your Macintosh has:
Round mouse port
Flat USB mouse port
2. Connect one end of the appropriate mouse cable to the
standard
Mouse/Com port or the USB Mouse port on the
projector.
connecting Mac mouse cable connecting USB mouse cable
3. Connect the other end to the port on your Macintosh.

Turning the Projector On and Off

After you have connected your computer and other equipment, you can plug in the projector and turn it on.
1. Connect the power cable to your projector’s power inlet.
2. Plug the other end of the cable into a grounded electrical
outlet.
The power light on top of the projector turns orange. This indicates that the projector is receiving power, but is not yet turned on.
14 Connecting to a Desktop Computer
power light
3. Use the tab on the lens ring to rotate the ring and pop out
the lens.
tab
4. Squeeze the lens cap tabs and remove the lens cap.
Squeeze here
warning
Never look into the lens when the lamp is on. This can damage your eyes, and is especially dangerous for children.
5. Press the red
power button
Power button on top of the projector.
power light
The power light flashes green, and then stays on. You may see a blue screen with the message
No Signal displayed.
This is normal.
6. Turn on or restart your computer. In a few moments, you
should see the computer display projected.
Connecting to a Desktop Computer 15
When you are ready to turn off the projector, follow these steps:
caution
To avoid damaging the lamp, never unplug the power cord when the power light is green.
1. Press the red
Power button on top of the projector. You
see a confirmation message. (If you don’t want to turn it off, press any other button.)
2. Press the
Power button again. The Power light flashes
orange for about a minute and the fan gets louder as the projector cools down. When the projector has cooled, the orange light stays on and the fan shuts off.
If you want to turn the projector on again, wait until the orange light stops flashing. Then press the
Power button.
3. When you are finished using the projector, replace the lens
cap, retract the lens, and unplug the power cord.

Turning On Other Equipment

If you’re using a VCR, other external video source, or additional equipment with the projector, turn on the equipment in this order:
1. Video source
2. External audio source
3. Projector
4. External speakers or PA system
5. Computer
When you’re ready to shut down, turn off the equipment in the reverse order.
16 Connecting to a Desktop Computer
Appendix B: Using the Projector Menus
B
The on-screen menus let you customize and adjust projector features. The following 8 menus and features are available:
Video
Controls the look and quality of the projected image (from a computer or video source).
Audio
Adjusts the volume and tone (treble/bass).
Effect
Customizes the drawing tools available on the remote control.
Setting
Adjusts features such as the keystone setting, blank screen color, message prompt, and power management system.
User’s Logo
Lets you capture and store an image to be displayed with the A/V Mute button, or as the startup screen.
Advanced
Controls settings such as menu language, use of startup screen, color temperature, and rear or ceiling projection.
About
Reset All
Provides information about lamp usage and the current display settings.
Restores the factory defaults for all the projector settings.
Using the Projector Menus 17

Changing Menu Settings

You use the Menu, Enter and Esc buttons on the remote control to change menu settings.
To change a menu setting:
1. To access the menu system, open the cover on the lower
part of the remote control and press the
Menu button.
menus
E-Zoom
2
1
Menu
Comp
S-Video
Auto
P in P
Power
R/C ON
3
Enter
Esc
Help
Video
Resize
- Volume +
Freeze
A/V Mute
Menu button
You see the following:
OFF
4
5
18 Using the Projector Menus
Video menu options
note
The options available in some submenus vary, depending on whether the current image source is the computer or a video source.
As you select a menu, a submenu of options appears to the right.
2. Press the bottom of the
Enter button (or grasp it between
your thumb and finger and tilt it down) to scroll through the menus.
When you highlight a menu, its options are shown on the right.
3. When the menu you want is highlighted, press the center of
Enter button to select it.
the
The highlight moves to the first option for that menu.
4. Press the bottom of the
Enter button (or grasp it between
your thumb and finger and tilt it down) to scroll through the options.
5. Press the right or left side of the
Enter button (or grasp it
between your thumb and finger and tilt it to the side) to change the setting.
6. If you want to go back to the default settings on any menu,
select
7. Press the
Reset
Esc
, press
Enter
, select
, and then press
Yes
Enter
button on the remote to go back to the main
menu display. Your changes are saved automatically.
.
button to exit the menu system.
8. Press the
Menu
The settings available in each of the menus are described below.
Using the Projector Menus 19
note
p
Some options are limited to being enabled (turned on) or disabled (turned off).

Video Menu (Computer Image Source)

The Video menu lets you make adjustments to the projected image. The following options are available when the image source is your computer.
Menu item Description
The computer must be connected and operating, and the i mage source on the
rojector must be set to Computer for you to access these menu options.
20 Using the Projector Menus
Position Use the Enter button to move the screen
position in the corresponding direction.
When you finish making adjustments, press the Esc button.
Tracking Matches the projector’s internal clock to
various computer graphic signals. Adjust this setting to remove vertical lines from the image.
Sync Synchronizes with the tracking signal sent from
the computer. Adjust this setting to correct fuzziness or screen flicker.
Brightness Lightens or darkens the overall image. Increase
brightness to lighten an image, or decrease it to darken the image.
Contrast Adjusts the difference between light and dark
areas. Increase the contrast to make light areas lighter and dark areas darker. Decrease it to minimize the difference between light and dark areas.
Menu item Description
Color Adjusts the color balance (red:green:blue) of
the input source.
Increase the color setting for more intense color on the screen, and lower the setting for less intense color.
When you finish making adjustments, press the Esc button.
Sharpness Adjusts the sharpness of the screen image.
Auto Setup Set to On to have the computer automatically
optimize the image for projection.
Gamma Adjusts the projected image for natural
coloration.
Reset Returns all menu items to their initial factory
defaults.
Using the Projector Menus 21
note
f
p y
The projector’s image source must be set to Video, and the video source (such as a VCR or camcorder) must be connected and operating
or you to access these menu options. For example, the projector must actually be
rojecting the image from our video tape if you’re
using a VCR.

Video Menu (Video Image Source)

The Video menu lets you make adjustments to the projected image. The following options are available when the image source is Video.
Menu item Description
Position Use the Enter button to move the screen
position in the corresponding direction.
When you finish making adjustments, press the Esc button.
Brightness Lightens or darkens the overall image. Increase
brightness to lighten an image, or decrease it to darken the image.
Contrast Adjusts the degree of difference between light
and dark areas. Increase the contrast to make light areas lighter and dark areas darker. Decrease it to minimize the difference between the lightest and darkest areas of the image.
Color Adjusts color density. Increase the setting for
darker and more opaque colors. Decrease it for lighter and less opaque colors.
Tint (NTSC only)
Sharpness Adjusts the sharpness of the screen image.
Gamma Adjusts the projected image for natural
Mode Specifies the image signal mode: Auto, NTSC,
Reset Returns all menu items to their initial factory
Adjusts the red-green color balance of the screen. Increase tint to add more green, or decrease it to add more red.
coloration.
NTSC4.43, PAL, M-PAL, N-PAL, PAL 60, SECAM.
defaults.
22 Using the Projector Menus

Audio Menu

Use the Audio menu to adjust the sound volume and quality of your audio.
Menu item Description
Volume Adjusts the volume level for the projector’s
speaker and audio-out terminal.
Increase the setting to raise the volume, or decrease it to lower the volume.
Tone Adjusts the sound quality. Move left to increase
bass and right to increase treble.
Reset Returns all menu items to their initial factory
defaults.
Using the Projector Menus 23

Effect Menu

The Effect menu lets you customize the drawing tools available on the remote control.
Menu item Description
Cursor/ Stamp
Box Selects a box color and shape.
Marker Selects the marker (horizontal or vertical lines)
Freehand Selects the color and width for freehand lines
Cursor Speed Adjusts the cursor speed to Low, Middle, or
Reset Returns all menu items to their initial factory
Selects the stamp you want to use as the cursor graphic and lets you enlarge it.
color and width (from 2 to 32 pixels).
(2 to 148 pixels).
High.
defaults.
24 Using the Projector Menus

Setting Menu

The Setting menu allows you to set or adjust various projector options.
Menu item Description
Keystone Adjusts a trapezoid (distorted) image to a 4:3
rectangle, correcting up to a ± 15° tilt.
P-in-P Selects the image source (composite or
S-Video) for the picture-in-picture subscreen.
No-Signal Msg
Prompt Turns off the message identifying the image
A/V Mute Specifies whether a blue, black, or user logo
Power Mgmt Sys
Reset Returns all menu items to their initial factory
Specifies whether no screen, a black screen, a blue screen, or a user logo is displayed when the projector is not receiving a signal.
source (computer or video).
screen is displayed when the A/V mute button is pressed.
Turns on the power management system which works with your computer’s power management.
defaults.
Using the Projector Menus 25

User’s Logo Feature

The User’s Logo feature allows you to transfer any image on your computer to the projector, and then use it as the screen displayed when the projector is not receiving a signal. You can also set it as a startup screen or to be displayed when you press
A/V Mute button on the remote. The image can be a
the company logo, slogan, photograph, or another other image you want to use.

Capturing the Image

26 Using the Projector Menus
You start by displaying the image you want to use on the projector. You can use an image from either a computer or video source such as a VCR or digital camera. Then follow these steps to capture the image and transfer it to the projector:
1. Press the with the Video menu highlighted.
2. Press the bottom edge of the down) to highlight the
button. You see the main menu listing,
Menu
button (or move it
Enter
User’s Logo
menu.
3. Press Enter to select this feature. You see the following message:
4. Select
Yes and press Enter. A selection box displays over
the image.
5. Use the
Enter button on the remote control to select the
area of the image you want to use. Once you have selected the entire area, press Enter.
6. When you see the message “Do you use this image?” select
Yes and press Enter. If you want to change the area
selected, select
No and repeat step 5. You see the following:
7. Use the Enter button on the remote control to select a zoom rate (display size), and then press
Enter.
Using the Projector Menus 27
8. When the following message appears, select
Enter.
Yes and press
Saving the logo may take a few moments. Do not use the projector or other sources (computer, video, speaker, etc.) while the logo is being saved.
9. When you see the following message, press the
Enter button to redisplay the main menu.
Menu or
28 Using the Projector Menus
note
You can also set up your image as a startup scree n. Use the Advanced menu to enable the startup sc reen.

Assigning the Image to the No-Signal Message and/or A/V Mute Button

After your image is saved, you can set it up as the no-signal message and/or the screen that’s displayed when you press the
A/V Mute button.
1. Press the
Menu button. You see the main menu listing,
with the Video menu highlighted.
2. Press the bottom edge of the to highlight the
3. Press the
Setting menu.
Enter button to select the Setting menu.
4. Press the bottom edge of the to highlight
No-Signal Msg.
5. Press the right side of the
Enter button (or tilt it down)
Enter button (or tilt it down)
Enter button to select Logo. This
sets your image as the screen displayed when the projector is not receiving a signal.
6. If you want to set up your image as the A/V mute display, press the bottom edge of the to highlight
A/V Mute.
7. Press the right side of the
Enter button (or tilt it down)
Enter button to select Logo. This
sets your image as the screen displayed when you press the
AV/Mute button.
8. When you’re finished, press
To test your setting, press the
Esc or Menu.
A/V Mute button to display your
image. Press it again to turn off the image.
Using the Projector Menus 29

Advanced Menu

The Advanced menu lets you set additional projector options.
Menu item Description
Language Selects the language to be used in the menus:
Japanese, English, French, German, Italian, Spanish, Portuguese, Chinese, or Korean.
Startup Screen
Color Temp Adjusts the whiteness of the screen. Positive
Rear Proj. Mirrors the projected image so it looks correct
Ceiling Flips the projected image so it looks correct
Reset Returns all Advanced menu items to their initial
Displays the image you have saved as a user logo during the projector’s startup.
color temperature values provide a cold white; negative values provide a warmer white.
when you’re projecting from behind onto a translucent screen. Selecting ON turns mirroring on, while OFF turns it off (for a normal image).
when the projector is mounted upside-down from the ceiling. Selecting ON turns the feature on, while OFF turns it off (for a normal image).
factory defaults.
30 Using the Projector Menus

About Menu (Computer Image Source)

When the image source is a computer, the About menu displays information about the projector’s horizontal and vertical frequency, lamp hours, and computer connection.
Menu item Description
Lamp Displays the number of hours the current lamp
has been used.
Frequency Displays the projector’s horizontal and vertical
frequency.
Sync Polarity
Sync Mode Displays the sync mode of the computer.
Resolution Displays the output resolution of the computer
Refresh Rate
Displays the sync polarity of the computer.
video output.
Displays the refresh rate of the computer video output.
Using the Projector Menus 31

About Menu (Video Image Source)

When the image source is video, the About menu displays information about the projector’s lamp hours and video signal.
Menu item Description
Lamp Displays the number of hours the current lamp
has been used.
Video Signal Displays the input image signal mode.

Reset All Feature

32 Using the Projector Menus
The Reset All feature lets you return all the projector settings to their default values. It does not change or delete any user logo you have stored.
Select
Reset All
confirmation screen. Select or
to cancel.
No
and press the
Yes
button to display the
Enter
to reset all the default settings
Appendix C:
Technical Specifications
C

General Type of display Poly-silicon Thin Film Transistor

(TFT)
Size of liquid crystal panels Diagonal: 0.9 inch (22.9 mm)
Lens F=2.0–2.2, f=35–42 mm
Resolution 500c: 800 × 600 pixels
700c: 1024 × 768 pixels 710c: 1024 × 768 pixels
Color reproduction 24 bit, 16.7 million colors
Brightness 500c: 800 lumens (ANSI)
700c: 800 lumens (ANSI) 710c: 1000 lumens (ANSI)
Image size (diagonal) 2.2 to 25 feet (0.7 to 7.6 meters)
Projection distance 3.6 to 45.3 feet (1.1 to 13.8 meters)
Projection methods Front, rear, upside-down (ceiling
mount)
Internal speaker system 1 monaural
Optical aspect ratio 4:3 (horizontal:vertical)
Zoom ratio 1.2:1
Keystone correction angle
Supported video interface standards NTSC, NTSC4.43, PAL, PAL-M,
±15°
PAL-N, PAL60, SECAM
Technical Specifications 33

Projection Lamp Type UHE (Ultra High Efficiency)

Power consumption 120 W
Lamp life About 2000 hours
Part number ELPLP10S (710c)
ELPLP10B (500c, 700c)

Remote Control Range 32.8 feet (10 meters)

Batteries Alkaline AA (2)

Mouse Compatibility Supports PS/2, USB, Macintosh

Remote IR Receiver Supports EPSON Remote IR Receiver, 10-foot cable (typical

use for rear screen projection)

Mechanical Height 2.8 to 3.0 inches (72 to 77 mm)

Width 8.4 inches (213 mm)
Depth 10.5 inches (267 mm)
Weight 5.8 lb (2.6 kg)

Electrical Rated frequency 50/60 Hz

Power supply 100 to 120 VAC, 2.4 A
200 to 240 VAC, 1.2 A

Environmental Temperature Operating: 41 to 104° F (5 to 40° C),

34 Technical Specifications
Power consumption Operating: 360 W
Standby: 12 W
non-condensing Storage: 14 to 140° F (–10 to 60° C), non-condensing
Humidity Operating: 20 to 80% RH,
non-condensing Storage: 10 to 90% RH, non-condensing

Safety United States FCC Part 15J Class B

UL1950 Rev. 3
Canada DOC SOR/88-475
CSA C22.2 No. 950 Rev. 3
CE Marking Directive 89/336/EEC
EN 55022 Class B EN 50082-1
Directive 73/23/EEC
EN 60950
Supported Monitor
Displays
The following table lists the display formats supported by the projector:
Frequency
Mode Resolution
VGACGA VGAEGA
NEC400 640 x 400 24.83 / 56.65 21.053
VGA60 VGA72 VGA75 VGA85
SVGA56 SVGA60 SVGA72 SVGA75 SVGA85
XGA43i XGA60 XGA70 XGA75 XGA85
640 x 400 640 x 350
640 x 480 640 x 480 640 x 480 640 x 480
800 x 600 800 x 600 800 x 600 800 x 600 800 x 600
1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768
H(KHz)/V(Hz)
31.46 / 70
31.46 / 70
31.469 / 59.94
37.861 / 72.809
37.5 / 75
48.269 / 85.008
35.156 / 56.25
37.879 / 60.317
48.077 / 72.188
46.875 / 75
53.674 / 85.061
35.522 / 86.958
48.363 / 60.004
56.476 / 70.069
60.023 / 75.029
68.677 / 84.997
Dot (MHz)
25.175
25.175
25.175
31.5
31.5 36
36 40 50
49.5
56.25
44.9 65 75
78.75
94.5
SXGA1_70 SXGA1_75 SXGA1_85
SXGA2_60 SXGA2_75 SXGA2_85
1152 x 864 1152 x 864 1152 x 864
1280 x 960 1280 x 960 1280 x 960
63.851 / 70.012
67.5 / 75
77.094 / 84.999
60 / 60 75 / 75
85.938 / 85.002
94.5 108
121.5
108 126
148.5
Technical Specifications 35
Mode Resolution
Frequency H(KHz)/V(Hz)
Dot (MHz)
SXGA3_43i SXGA3_60 SXGA3_75 SXGA_85
UXGA48i UXGA60 (these are not supported by PowerLite 500c)
MACLC13 MACII13 MAC16 MAC19-60 MAC19 MAC21
NTSC (SXGA) NTSC (XGA)
PAL (SXGA) PAL (XGA)
SECAM (SXGA) SECAM (XGA)
The frequencies of some com puter s may not allow the image to
Note:
1280 x 1024 1280 x 1024 1280 x 1024 1280 x 1024
1600 x 1200 1600 x 1200
640 x 480 640 x 480 832 x 624 1024 x 768 1024 x 768 1152 x 870
1366 x 438 1024 x 438
1366 x 512 1024 x 512
1366 x 512 1024 x 512
46.433 / 86.871
63.981 / 60.02
79.976 / 75.025
91.146 / 85.024
62.5 / 96.08 75 / 60
34.975 / 66.62 35 / 66.67
49.725 / 74.55
48.193 / 59.28
60.241 / 74.93
68.682 / 75.062
15.734 / 60 28.486
15.625 / 50 28.846
15.625 / 50 28.846
be displayed correctly.
78.75 108 135
157.5
135 162
31.33
30.24
57.28 64 80 100
20.890
21.154
21.154
36 Technical Specifications
Computer Connector
Pin Assignments
The Computer port is a female video RGB, 15-pin micro-D-style connector. Here are the pin assignments:
Input pin Computer connector signals
1 Red video
2 Green video
3 Blue video
4 GND
5 GND
6 Red video GND
7 Green video GND
8 Blue video GND
9Reserve
10 Synchronous GND
11 GND
12 SDA
13 Horizontal sync/composite sync
14 Vertical sync
15 SCL
Technical Specifications 37
.

Index

A
A/V Mute Button, 29 About menu, 31 to 32 Advanced menu, 30 Audio
connecting desktop, 9, 13 menu, 23
B
Brightness, 33 Brightness setting, 20, 22 Buttons, remote control, 18 to 19
C
Camcorder, adjusting the projected image, 22 CE Marking, 35 Ceiling, hanging the projector from, 30 Color setting, 21, 22 Color Temp setting, 30 Computer connector pin assignments, 37 Computer, adjusting projected image for, 20 Connecting projector
to a desktop Macintosh, 10 to 14 to a desktop PC, 7 to 9
Contrast setting, 20, 22
D
DIP switches, 12 Display formats, supported, 35 to 36 Distance from projector to screen, 5 to 6 Drawing tools, 24
E
Effect menu, 24 Electrical specifications, 34 Environmental specifications, 34 to 35
F
Formats, supported display, 35 to 36
G
Gamma setting, 21, 22
H
Humidity requirements, 34
I
Image
adjusting position, 20, 22 adjusting quality, 20 to 22 size range, 6, 33
Image signal mode, 22
K
Keystone setting, 25
L
Lamp specifications, 34 Language setting, 30 Lumens, 33
38 Index
M
Macintosh, connecting projector to, 10 to 14 Mechanical specifications, 34 Menus
About, 31 to 32 Advanced, 30 Audio, 23 changing settings, 18 to 19 Effect, 24 Reset All, 32 Setting, 25 User’s Logo, 26 Video, 20 to 22
Monitors, supported, 35 to 36
S
Setting menu, 25 Sharpness setting, 21, 22 Speakers, adjusting sound, 23 Specifications
electrical, 34 environmental, 34 to 35 general, 33 lamp, 34 mechanical, 34 remote control, 34
safety, 35 Startup screen, 30 Sync setting, 20
P
Picture-in-picture option, 25 Pin assignments, connector, 37 Positioning the projector, 5 to 6 Positioning the screen image, 20, 22 Power
consumption, 34 management, 25 supply, 34
Projector
distance to screen, 6 hanging from the ceiling, 30 lamp specifications, 34 positioning, 5 to 6 positioning the screen image, 20, 22 setting up, 5 turning off, 16 turning on, 14
R
Rear projection, 30 Remote control
buttons, 18 to 19
specifications, 34 Reset All feature, 32 Resolution, 33
T
Temperature requirements, 34 Tint setting, 22 Tone setting, 23 Tracking setting, 20 Turning off the projector, 16 Turning on additional equipment, 16 Turning on the projector, 14
U
User’s Logo feature, 26
V
VCR, adjusting the projected image, 22 Video
adjusting the projected image, 22 menus, 20 to 22
Volume setting, 23
Z
Zoom ratio, 33
Index 39
Loading...