Epson 6110 User Manual

User’s Guide

Notations Used in This Guide

f Safety Indications

So that you can use the projector safely and correctly, symbols are applied in the documentation and on the projector to indicate possible harm to the user or to others and the risk of damage to property. The indications and their meaning are as follows. Make sure you understand them properly before reading the guide.

Warning

Caution

f General Information Indications

Attention

Indicates the possibility of death or serious injury if this symbol is ignored or if sufficient care is not taken.

Indicates the possibility of injury or damage to property if this symbol is ignored or if sufficient care is not taken.

Indicates procedures which may result in damage or injury if sufficient care is not taken.

Indicates additional information and points which may be useful to know regarding a topic.

Procedure

[ (Name) ]

"(Menu Name)"

Indicates a page where detailed information regarding a topic can be found.

Indicates that an explanation of the underlined word or words in front of this symbol appears in the glossary of terms. See the "Glossary" section of the "Appendices". s p.74

Indicates operating methods and the order of operations. The procedure indicated should be carried out in the order of the numbered steps.

Indicates the name of the buttons on the remote control or the control panel. Example: [Esc] button

Indicates configuration menu items. Example: "Image" - "Brightness"

Projector Features......................................................................................5

Part Names and Functions ........................................................................6

Front/Top..............................................................................................................6

Rear (EMP-6110) ................................................................................................. 7

Rear (EMP-6010) ................................................................................................. 8

Control Panel ....................................................................................................... 9

Remote Control ..................................................................................................10

Base ...................................................................................................................11

Useful Functions

Changing the Projected Image................................................................13

Automatically Detect Incoming Signals and Change the Projected Image

(Source Search) .................................................................................................13

Changing Directly from the Remote Control ......................................................14

Functions for Enhancing Projection.......................................................15

Selecting the Projection Quality (Selecting Color Mode) ................................... 15

Hiding the Image and Sound Temporarily (A/V Mute) ....................................... 16

Freezing the Image (Freeze).............................................................................. 16

Changing the Aspect Ratio (Aspect) .................................................................. 17

Pointer Function (Pointer) ..................................................................................18

Enlarging Part of the Image (E-Zoom) ...............................................................19

Specifying the projector(s) that will respond to the

remote control when multiple projectors are used ...............................20

Setting the projector ID ...................................................................................... 20

Setting the ID of the projector to be operated ....................................................21

Color adjustment when using multiple projectors

(Multi-Screen Color Adjustment) ............................................................22

Summary of Adjustment Procedure ...................................................................22

Image Correction Method...................................................................................23

Security Functions ...................................................................................24

Managing Users (Password Protect) ................................................................. 24

Restricting Operation (Operation Lock)..............................................................27

Anti-Theft Lock ...................................................................................................28

Configuration Menu

Using the Configuration Menu................................................................ 30

List of Functions ......................................................................................31

Image Menu....................................................................................................... 31

Signal Menu....................................................................................................... 32

Settings Menu.................................................................................................... 33

Extended Menu.................................................................................................. 35

Network Menu (EMP-6110 Only)....................................................................... 37

Info Menu (Display Only) ................................................................................... 40

Reset Menu ....................................................................................................... 41

Troubleshooting

Using the Help ..........................................................................................43

Problem Solving....................................................................................... 44

Reading the Indicators ....................................................................................... 44

When the Indicators Provide No Help................................................................ 49

Appendices

Installation Methods ................................................................................ 57

Cleaning ....................................................................................................58

Cleaning the Projector's Surface ....................................................................... 58

Cleaning the Lens Cover Glass......................................................................... 58

Cleaning the Air Filter ........................................................................................ 58

Replacing Consumables ......................................................................... 61

Replacing the Remote Control Batteries ........................................................... 61

Replacing the Lamp ........................................................................................... 62

Replacing the Air Filter ...................................................................................... 65

Saving a User’s Logo............................................................................... 68

Screen Size and Distance........................................................................ 70

Connecting to External Equipment ........................................................ 71

Connecting to an External Monitor .................................................................... 71

Connecting to External Speakers (EMP-6110 Only) ......................................... 71

Connecting a LAN Cable (EMP-6110 Only)............................................ 72

Optional Accessories and Consumables .............................................. 73

Glossary....................................................................................................74

List of ESC/VP21 Commands.................................................................. 76

Command List.................................................................................................... 76

Cable Layouts.................................................................................................... 76

Contents

PJLink (EMP-6110 Only) ..........................................................................77

List of Supported Monitor Displays........................................................78

Specifications ...........................................................................................79

Appearance ...............................................................................................81

Index ..........................................................................................................82

Projector Features

High reliability

f A highly efficient air filter is installed

Decreases the amount of dust that enters the projector.

f A message and an indicator inform you when the air filter is

clogged and requires cleaning or that it is time to replace the filter.

The projector detects when the air filter is becoming clogged up and alerts you with a message and an indicator to give you advanced notice that the filter will soon need cleaning or replacing. Also, the display of a message and an indicator when the filter requires cleaning or replacement helps to ensure that regular maintenance is performed. s p.47

f Easy to detach, instantly-removable filter

There is only one air filter and it can be removed and installed easily.

s p.65

Enhanced security functions

f Password Protect to restrict and manage users By setting a password you can restrict who can use the projector. s p.24

f Operation Lock restricts button operation on the control panel

You can use this to prevent people changing projector settings without permission at events, in schools, and so on. s p.27

Control and monitor from a remote location by a LAN

f Control and monitor from a computer using EMP Monitor (EMP-

6110 only)

You can use the EMP Monitor software supplied with the projector to display and check the projector's status on a computer monitor and control it from a computer. s EMP Monitor Operation Guide

f Mail notification function when problems occur

When problems occur in the projector a mail notification is sent to a nominated e-mail address to inform the recipient of the projector's status.

s p.38

Multi-screen color adjustment allows you to adjust the color of several projectors

When several projectors are lined up and projecting images, you can adjust the color tone of each image with multi-screen color adjustment.

s p.22

Easy to handle

f Direct power On/Off

In places where power is managed centrally, such as in a conference room, the projector can be set to power on and off automatically when the power source to which the projector is connected is switched on or off.

f Equipped with various anti-theft devices

The projector is equipped with the following security devices. s p.28

• Security slot

• Security cable installation point

• Cable cover key installation hole

f No cool down delay

After turning the projector's power off, you can disconnect the projector's power cable without having to wait for the projector to cool down first.

f High powered, 1.6 times zoom lens

The 1.6 times zoom allows for a wide range of installation positions to suit most room layouts, whether the projector is on a stand, a table, or ceiling mounted.

Part Names and Functions

Front/Top

How to open the zoom ring cover

A B

* Do not remove the zoom ring cover, and do not use the projector

when it is open. Otherwise dust can enter into the projector and shorten the optical engine's service life.

Name Function

Speaker

Control panel s p.9

Lamp cover Open this cover when replacing the projector's

lamp. s p.63

Name Function

Air exhaust vent Allows cooling air from within the unit to

escape.

Caution

Do not place objects that may become warped or otherwise affected by heat near the air exhaust vent and do not put your face or hands near the air exhaust vent while projection is in progress.

Status indicators The color of the indicators and whether they

are flashing or lit indicates the status of the projector. s p.44

Front adjustable

feet

Remote receiver Receives signals from the remote control.

Air filter

(Air intake vent)

Zoom ring Adjusts the image size. s Quick Start Guide

Focus ring Adjusts the image focus. s Quick Start

Turn to extend and adjust the position of the projected image when the projector is placed on a surface such as a desk. s Quick Start

Guide

s Quick Start Guide

This prevents dust and other foreign particles from getting inside the projector when air is drawn in. If dust collects here it can cause the internal temperature of the projector to rise, and this can lead to problems with operation and shorten the optical engine's service life. The projector displays a warning message when it is time to clean or replace the air filter.

s p.58, 65

Guide

Part Names and Functions

Rear (EMP-6110)

B C

D E

LKJ IHG F

CDE

Name Function

Storage feet When storing the projector upright, make sure

that these feet are at the bottom.

Security slot (j) s p.28

S-Video port

Video port

Audio port L-Audio-R port

Rear foot

Power inlet Connects to the power cable. s Quick Start

For S-videog signals from video sources.

For composite videog signals from video sources.

These connect to the audio out port of equipment that is connected to the S-Video or Video port. s Quick Start Guide, p.33

Guide

Name Function

LAN port When a LAN cable is connected, you can

monitor and control the projector over a LAN.

s p.72

RS-232C port When controlling the projector from a

computer, connect it to the computer with an RS-232C cable. This port is for control use and should not normally be used. s p.76

Remote receiver Receives signals from the remote control.

s Quick Start Guide

Computer2 port For video signals from a computer and

component video sources.

Audio port Connect to the audio out port of the computer

connected to the Computer2 port. s Quick

Start Guide

Computer1 port For video signals from a computer and

component video sources.

Audio port Connect to the audio out port of the computer

connected to the Computer1 port. s Quick

Start Guide

Monitor Out port Outputs the computer image signal connected

to the Computer1 port to an external monitor. This is not available for component video signals or other signals being input to any port

other than Computer1 port. s p.71

Audio Out port Outputs the sound of the image currently being

projected to external speakers.

g signals from other video

Part Names and Functions

Rear (EMP-6010)

Name Function

Storage feet When storing the projector upright, make sure

JI H G F

CDE

that these feet are at the bottom.

Name Function

RS-232C port When controlling the projector from a

computer, connect it to the computer with an RS-232C cable. This port is for control use and should not normally be used. s p.76

Remote receiver Receives signals from the remote control.

s Quick Start Guide

Computer2 port For video signals from a computer and

component video sources. s Quick Start Guide

Computer1 port For video signals from a computer and

component video sources. s Quick Start Guide

Monitor Out port Outputs the computer image signal connected

to the Computer1 port to an external monitor. This is not available for component video signals or other signals being input to any port other than Computer1 port. s p.71

g signals from other video

Security slot (j) s p.28

S-Video port

Video port

L-Audio-R port Connects to the audio out port of the

Rear foot

Power inlet Connects to the power cable. s Quick Start

For S-videog signals from video sources.

For composite videog signals from video sources.

equipment that is providing the image source to input the audio. s Quick Start Guide

Guide

Part Names and Functions

Control Panel

Name Function

[Menu] button Displays and closes the configuration menu.

s p.30

Name Function

[a] [b] buttons Adjusts the sound volume.

If pressed when a configuration menu or a help screen is displayed, these buttons select menu items and setting values. s Quick Start Guide, p.30

[Help] button Displays and closes the help screen which

shows you how to deal with problems if they occur. s p.43

[Esc] button Stops the current function.

If pressed when a configuration menu is displayed, it moves to the previous menu level.

s p.30

[Enter] button If pressed during projection of computer signal

images, it automatically adjusts the tracking, synchronization, and position to project the optimum image. When a configuration menu or a help screen is displayed, it accepts and enters the current selection and moves to the next level. s p.30

[Power] button Turns the projector power on or off. s Quick

Start Guide

[Source Search]

button

[w] [v] buttons Corrects keystone distortion.

Changes to the next input source that is connected to the projector and is sending an image. s p.13

If pressed when a configuration menu or a help screen is displayed, these buttons select menu items and setting values. s Quick Start Guide, p.30

Part Names and Functions

Remote Control

B C

D E

F G H I

V U T

S R

Q P

O N M L

Name Function

[Pointer] button Press to activate the on screen pointer.

s p.18

[Comp1] button Displays images from the Computer1 port.

s p.14

[Comp2] button Displays images from the Computer2 port.

s p.14

[S-Video] button Displays images from the S-Video port.

s p.14

[Video] button Displays images from the Video port. s p.14

[Auto] button If pressed during projection of computer signal

images, it automatically adjusts the tracking, synchronization, and position to project the optimum image. s p.32

Numeric buttons Used to enter a password or, when using

multiple projectors, to set the ID of the projector to be operated. s p.26, 23

[Search] button Changes to the next input source that is

connected to the projector and is sending an image. s p.13

[Volume] buttons (a) Decreases the volume.

(b) Increases the volume. s Quick Start Guide

Name Function

[E-Zoom] buttons

(z) (x)

[A/V Mute] button Turns the video and audio on or off. s p.16

(z) Enlarges the image without changing the projection size. (x) Reduces parts of images that have been enlarged using the [z] button. s p.19

[Aspect] button

[Help] button Displays and closes the help screen which

[Color Mode]

button

The aspect ratiog changes each time the button is pressed. s p.17

shows you how to deal with problems if they occur. s p.43

Each time the button is pressed, the color mode changes. s p.15

Part Names and Functions

Name Function

[ID] button When using multiple projectors, press this

button to specify the ID of the projector to be used. This button is also used to determine the ID of a projector and to check whether the remote control can be used. s p.20

[Num] button While this button is pressed, the remote enters

numeric keypad mode, and each of the keys on the keypad is enabled. Releasing the [Num] button clears the numeric keypad mode.

s p.26, 23

[Freeze] button Images are paused or unpaused. s p.16

[Esc] button Stops the current function.

If pressed when a configuration menu is displayed, it moves to the previous level.

s p.30

[Enter] button When a configuration menu or a help screen is

displayed, it accepts and enters the current selection and moves to the next level. s p.30

Base

[h] button When a configuration menu or help screen is

displayed, it selects menu items and setting values. s p.30

[Menu] button Displays and closes the configuration menu.

s p.30

[Power] button Turns the projector power on or off. s Quick

Start Guide

Remote control

light-emitting area

Outputs remote control signals. s Quick Start Guide

Name Function

Front adjustable

feet

Security cable

installation point

Suspension

bracket fixing points (4 points)

Handle Use this handle when carrying the projector.

Turn to extend and adjust the position of the projected image when the projector is placed on a surface such as a desk.

Pass a commercially available anti-theft wire lock through here when you want to secure the projector to a fixed object. s p.28

Attach the optional ceiling mount here when suspending the projector from a ceiling.

s p.57, 73

Useful Functions

This chapter explains useful functions for giving presentations and so on, and the security functions.

Changing the Projected Image..........................13

• Automatically Detect Incoming Signals and

Change the Projected Image (Source Search)................13

• Changing Directly from the Remote Control.................14

Functions for Enhancing Projection.................15

• Selecting the Projection Quality

(Selecting Color Mode) .....................................................15

• Hiding the Image and Sound Temporarily

(A/V Mute) .........................................................................16

• Freezing the Image (Freeze).............................................16

• Changing the Aspect Ratio (Aspect)................................17

• Pointer Function (Pointer) ...............................................18

• Enlarging Part of the Image (E-Zoom)...........................19

Specifying the projector(s) that will respond to the remote control when multiple

Color adjustment when using multiple

projectors (Multi-Screen Color Adjustment) ....22

• Summary of Adjustment Procedure............................... 22

• Image Correction Method ............................................... 23

Security Functions..............................................24

• Managing Users (Password Protect)............................... 24

Type of Password Protect .............................................................. 24

Setting Password Protect................................................................ 25

Entering the password.................................................................... 26

• Restricting Operation (Operation Lock)........................ 27

• Anti-Theft Lock ................................................................ 28

Installing the wire lock................................................................... 28

Cable cover locking method (EMP-6110 only) ............................. 28

projectors are used ............................................20

• Setting the projector ID....................................................20

• Setting the ID of the projector to be operated................21

Changing the Projected Image

You can change the projected image in the following two ways.

• Changing by Source Search The projector automatically detects signals being input from connected equipment, and the image being input from the equipment is projected.

• Changing directly You can use the remote control buttons to change to the target input port.

Automatically Detect Incoming Signals and Change the Projected Image (Source Search)

You can project the target image quickly as input ports with no image signal being input are ignored when you change by pressing the [Source Search] button.

Computer1 VideoS-VideoComputer2

Using the remote control Using the control panel

When two or more pieces of equipment are connected, press the [Source Search] button until the target image is projected.

The following screen showing the status of image signals is displayed when only the image that the projector is currently displaying is available, or when no image signal can be found. You can select the input port where the connected equipment you want to use is projecting. If no operation is performed after about 10 seconds, the screen closes.

The input port where no image signal is being input is skipped.

Procedure

When your video equipment is connected, start playback before beginning this operataion.

Changing the Projected Image

Changing Directly from the Remote Control

You can change directly to the target image by pressing the following buttons on the remote control.

Remote control

Changes to images from the Computer1 port.

Changes to images from the S-Video port.

Changes to images from the Computer2 port.

Changes to images from the Video port.

Functions for Enhancing Projection

Selecting the Projection Quality (Selecting Color Mode)

You can easily obtain the optimum image quality simply by selecting the setting that best corresponds to your surroundings when projecting. The brightness of the image varies depending on the mode selected.

Mode Application

Tex t Ideal for making presentations using black-and-

white materials in a bright room.

Photo (When computer images are input)

Ideal for projecting still pictures, such as photos, in a bright room. The images are vivid and brought into contrast.

Sports (When component video, S-video, or composite

video images are input) Ideal for watching TV programmes in a bright room.

The images are vivid and brought to life. Presentation Ideal for giving presentations in a bright room. Theatre Ideal for watching films in a dark room. Gives

images a natural tone. Game Ideal for playing video games in a bright room.

Excels at emphasizing dark gradations. sRGBg Ideal for images that conform to the sRGB color

standard. Blackboard Even if you are projecting onto a blackboard

(greenboard), this setting gives your images a natural

tint, just like when projecting onto a screen.

Procedure

Remote control

Each time you press the button, the color mode name is displayed on the screen and the color mode changes.

If you press the button while the color mode name is displayed on the screen, it changes to the next color mode.

The color mode can also be set using "Color Mode" in the

"Image" menu from the configuration menu.

p.31

Functions for Enhancing Projection

Hiding the Image and Sound Temporarily (A/V Mute)

You can use this when you want to focus the audience's attention on what you are saying, or if you do not want to show details such as when you are changing between files during presentations from a computer.

Procedure

Remote control

Each time you press the button, A/V Mute turns on or off.

• If you use this function when projecting moving images,

the images and sound continue to be played back by the source, and you cannot return to the point where A/V Mute was activated.

• You can choose to display black, blue, or logo as the A/V Mute display using the "Extended"-"Display"-"A/V

Mute" setting from the configuration menu.

p.35

Freezing the Image (Freeze)

When the moving image on the screen is frozen, the image continues to project, so you can project a moving image one frame at a time like a still photo. Also, you can perform operations such as changing between files during presentations from a computer without projecting any images if the freeze function is activated beforehand.

Procedure

Remote control

Each time you press the button, Freeze turns on or off.

• Audio does not stop.

• The image source continues to playback the moving images even while the screen is frozen, and so it is not possible to resume projection from the point where it was paused.

• If the [Freeze] button is pressed while the configuration menu or a help screen is displayed, the menu or help screen being displayed is cleared.

• Freeze still works while E-Zoom is being used.

Functions for Enhancing Projection

Changing the Aspect Ratiog (Aspect)

When video equipment is connected, images that have been recorded in digital video or onto DVDs can be viewed in 16:9 wide-screen format. You can change the aspect ratio for images in squeeze modeg as follows.

16:94:3 16.9 (below)16.9 (above)

Procedure

Remote control

If you press the button while the aspect name is displayed on the screen, it changes to the next aspect mode.

The color mode can also be set using "Aspect" in the

"Signal" menu from the configuration menu.

p.32

Each time you press the button, the aspect name is displayed on the screen and the aspect changes.

Functions for Enhancing Projection

Pointer Function (Pointer)

This allows you to move a pointer icon on the projected image, and helps you draw attention to the area you are talking about.

Procedure

Display the pointer.

Remote control

Move the pointer icon.

Remote control

Pointer icon

You can choose from three different kinds of pointer icon (

··

from the configuration menu.

) in "Pointer Shape" in the "Settings" menu

p.33

Each time you press the button, the pointer appears or disappears.

Functions for Enhancing Projection

Enlarging Part of the Image (E-Zoom)

This is useful when you want to expand images to see them in greater detail, such as graphs and tables.

Procedure

Start E-Zoom.

Remote control

Move the cross to the area of the image that you want to enlarge.

Remote control

Cross

Enlarge.

Remote control

Each time the button is pressed, the area is expanded. You can expand quickly by holding the button down. You can reduce the enlarged image by pressing the [x] button. Press the [Esc] button to cancel.

• The enlargement ratio appears on the screen. The selected area can be enlarged to between 1 to 4 times in 25 incremental steps.

• Tilt the [

] button to scroll the image.

Specifying the projector(s) that will respond to the remote control when multiple projectors are used

When the projector is being used together with several others, the projector that responds to the remote control can be limited as described below.

1: Using the configuration menu, set a

projector ID.

Projector ID: 1 Projector ID: 2

ID of projector to be operated: 2

2: Using the remote control, set the

ID of the projector to be operated on each of the projectors.

fter making the above setting, only the following projector(s) can be

operated with the remote control.

• Those for which the "Projector ID" and "ID of projector to be operated" are the same. (Ex.: The second projector in the above figure)

• When "0" is set as the "ID of the projector to be operated".

ID of projector to be operated: 2

Projector ID: 3

ID of projector to be operated: 2

Setting the projector ID

Procedure

Press the [Menu] button and then, from the configuration menu, select "Extended" - "Projector ID". s "Using the Configuration Menu" p.30

Using the remote control Using the control panel

• The default for the "Projector ID" is "Off". The default

for the "ID of projector to be operated" is "0". When "0" is set, the projector can be operated with the remote

See the guide displayed below the menu for more instructions.

control, regardless of the "Projector ID" setting.

• When the power to the projector is turned off, the setting made for "ID of the projector to be operated" returns to "0", such that it can subsequently be operated from the remote control.

Specifying the projector(s) that will respond to the remote control when multiple projectors are used

B C

Choose the ID you want to set and press the [Enter] button.

Press the [Menu] button to close the configuration menu.

Setting the ID of the projector to be operated

The ID of the projector to be operated must be set every time the projector is powered on.

Procedure

Point the remote control at the remote receiver of each of the set projectors, and then perform the following steps for each.

While holding down the [ID] button, press the number button corresponding to the ID of the projector to be operated.

Keep

pressed

Once this setting has been made, only the specified projector(s) can be operated with the remote control.

You can check which projector(s) can be operated with the remote control as described below.

• Point the remote control at the remote receiver of the projector you want to check, and then press the [ID] button. The following is displayed.

When remote control operations are

enabled:

Color adjustment when using multiple projectors (Multi-Screen Color Adjustment)

When several projectors are lined up and projecting images, you can adjust the brightness and color tone of each projector's image with multi-screen color adjustment so that the colors of images from each projector match closely. In some cases the brightness and color tone may not match completely even after adjustment.

Attention

When the projector is to be used together with several others, such as when they are lined up on a desktop, make the following configuration settings. If the projectors are not configured correctly, there is a danger that hot exhaust air from one projector will trigger a High Temp Warning in that positioned next to it.

• Project an image that is at least 50 inches in size.

• Ensure that the ambient temperature is no more than 35°C.

• Position the projectors no less than 55 cm apart.

• Do not place the projectors in a high-temperature location, such as in direct sunlight, or near the vents of a heater or airconditioner.

2. Making image corrections

Perform image correction for each of the projectors. Using image correction you can adjust from black to white in five stages called levels 1 to 5, and in each level 1 to 5 you can adjust the following two points.

• Adjusting brightness Adjust each image by levels 1 to 5 so that they are all equal.

• Adjusting color Adjust each image by levels 1 to 5 so that the colors match using "Color Correct. (G/R)" and "Color Correct. (B/Y)".

Summary of Adjustment Procedure

Make adjustments according to the following procedure.

1. Restricting the projectors that can be operated with the remote control.

Regardless of how many projectors you are using together, you can make the settings such that only the projector that needs the correction will respond to the remote control. s p.20

Color adjustment when using multiple projectors (Multi-Screen Color Adjustment)

Image Correction Method

Procedure

Press the [Menu] button and select "Extended" "Multi-screen" from the configuration menu. s "Using the Configuration Menu" p.30

Select the level to be adjusted in "Adjustment Level".

• Each time a level is selected, the pattern of the level selected is displayed.

• You can start adjusting from any level, usually you can make it darker or lighter by adjusting 1 to 5 or 5 to 1.

Adjust the brightness with "Brightness Correct.".

• When you select level 5, it adjusts to the darkest image from several projectors.

• When you select level 1, it adjusts to the brightest image from several projectors.

• When you select level 2 to 4, it adjusts to the mid-range brightness image from several projectors.

• Each time the [Enter] button is pressed the image displayed changes between the pattern display and the actual image, and you can check the adjustment results and make corrections in the actual image.

E F

Adjusting "Color Correct. (G/R)" and "Color Correct. (B/Y)".

Each time the [Enter] button is pressed the image displayed changes between the pattern display and the actual image, and you can check the adjustment results and make corrections in the actual image.

Repeat procedures 2 to 4 until adjustments are finished.

When all adjustments are finished, press the [Menu] button to close the configuration menu.

Security Functions

The projector has the following enhanced security functions.

• Password Protect You can limit who can use the projector.

• Operation Lock You can prevent people changing the settings on the projector without permission.

• Security Lock The projector is equipped with various types of anti-theft security devices.

Managing Users (Password Protect)

When Password Protect is activated, people who do not know the password cannot use the projector to project images even if the projector power is on. Furthermore, the user's logo that is displayed when you turn on the projector cannot be changed. This acts as an anti-theft device as the projector cannot be used even if it is stolen. At the time of purchase, Password Protect is not activated.

f Type of Password Protect

The following three kinds of password protect settings can be made according to how the projector is being used.

• "Power On Protect"

When "Power On Protect" is "On", the password must be entered whenever the projector is turned on after it has been disconnected from the power supply it was connected to the last time the password was entered. If the correct password is not entered, projection does not start.

• "User's Logo Protect"

When "User's Logo Protect" is set to "On" the user's logo cannot be changed and the following setting changes for user's logo are prohibited.

• Capturing a user's logo

• Settings for "Display Background", "Startup Screen", and "A/V Mute" from "Display" on the configuration menu.

• "Network Protect" (EMP-6110 only)

When "Network Protect" is set to "On" setting changes for "Network" in the configuration menu are prohibited.

Security Functions

f Setting Password Protect

Use the following procedure to set Password Protect.

Procedure

Hold down the [Freeze] button for about five seconds.

The password protect setting menu is displayed.

Remote control

• If Password Protect is already activated, you must enter the password. If the password is entered correctly, the password protect

setting menu is displayed.

p.26

• When the password is set, stick the password protect sticker in a visible position on the projector as a further theft deterrent. (EMP-6110 only)

"Entering the password"

Turn on "User's Logo Protect".

(1) Select "User's Logo Protect", and then press the [Enter] button. (2) Select "On", and then press the [Enter] button. (3) Press the [Esc] button.

Turn on "Network Protect". (EMP-6110 only)

(1) Select "Network Protect", and then press the [Enter] button. (2) Select "On", and then press the [Enter] button. (3) Press the [Esc] button.

Set the password.

(1) Select "Password", and then press the [Enter] button. (2) The message "Change the password?" is displayed, select

"Yes" and then press the [Enter] button. The default setting for the password is "0000". Change this to your own desired password. If you select "No", the screen shown in step 1 is displayed again.

Turn on "Power On Protect".

(1) Select "Power On Protect", and then press the [Enter] button. (2) Select "On", and then press the [Enter] button. (3) Press the [Esc] button.

Security Functions

(3) While holding down the [Num] button, enter a four digit

number using the numeric buttons. The number entered is displayed as "****". When you enter the fourth digit, the confirmation screen is displayed.

Remote control

Keep

pressed

Numeric buttons

(4) Re-enter the password.

The message "Password accepted." is displayed. If you enter the password incorrectly, a message is displayed prompting you to re-enter the password.

f Entering the password

When the password entry screen is displayed, enter the password using the numeric buttons on the remote control.

Procedure

While holding down the [Num] button, enter the password by pressing the numeric buttons.

When you enter the correct password, projection begins.

Attention

• If an incorrect password is entered three times in succession, the message "The projector's operation will be locked." is displayed for about five minutes, and then the projector switches to standby mode. If this happens, disconnect the power plug from the electrical outlet and then reinsert it and turn the projector's power back on. The projector displays the password entry screen again so that you can enter the correct password.

• If you have forgottten the password, make a note of the "Request Code: xxxxx" number that appears on the screen and contact the nearest address provided in the Support and Service Guide.

Epson Projector Contact List

• If you continue to repeat the above operation and input the wrong password thirty times in succession, the following message is displayed and the projector does not accept any more password entries. "The projector's operation will be locked. Contact Epson

as described in your documentation."

Contact List

Epson Projector

+ 58 hidden pages