Eneo VKC-1416C Operating Instructions Manual

Operating Instructions

1/4” Day&Night Autofocus Camera
VKC-1416C

2

WARNING AND CAUTIONS

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR MOISTURE.
DO NOT INSERT ANY METALLIC OBJE CT THROUGH VENTILATION GRILLS.

EXPLANATION OF GRAPHICAL SYMBOLS

The lightning flash with arrowhead symbol, within an equilateral triangle,
is intended to alert the user to the presence of uninsulated ''dangerous
voltage'' within the product's enclosure that may be of sufficient magnit ude
to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangl e is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accom panying the product.

PRECAUTIONS

WARNING : TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER(OR BACK).

NO USER-SERVICABLE PARTS INSIDE.

REFFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRI C S HOCK

DO NOT OPEN

CAUTION

Safety

Should any liq uid or solid objec t fall into the cabin et,
unplug the unit and have it checked by
qualified personnel before operating it any further.

Unplug the unit fr om the wall outlet i f it is not going to
be used for several days or more.
To disconnect th e cord, pull it ou t by the plug. Neve r
pull the cord itself.

Allow adequate air circ ulation to preve nt internal heat
build-up. Do not place t he unit o n soft surf aces (rugs,
carpets, sofas, etc.) or near materials (curtains,
draperies) that may block the ventilation holes.

Height and vertical linearity controls located on the
rear panel are for special adjustments by qualified
personnel only.

Installation

Do not instal l t he unit in an e xtrem ely hot or hum i d place
or in a place subject to excessive dust, mechanical
vibration.

The unit is not designed to be waterproof.
Exposure to rain or water may damage the unit.

Cleaning

Clean the unit with a slightly damp soft cloth.
Use a mild household detergent. Never use strong
solvents such as thinner or benzine as they might
damage the finish of the unit.

Retain the origi nal car ton a nd packing materi als for s afe
transport of this unit in the future.

3

FCC COMPLIANCE ST ATEM E NT

CE COMPLIANCE STATEMENT

INFORMATION TO THE USER: THIS EQUIPMENT HAS BEEN TESTED

AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE,
PURSUANT TO PART 15 OF THE FCC RULES. THESE LIMITS ARE DESIGNE D

TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL

INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL
ENVIRONMENT. THIS EQUIPMENT GENERATES, USES, AND CAN RADIATE

RADIO FREQUENCY ENERGY AND IF NOT INSTALLED AND USED IN

ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL
INTERFERENCE TO RADIO COMMUNICATIONS.
OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO
CAUSE HARMFUL INTERFERENCE IN WHICH CASE THE USER WILL BE
REQUIRED TO CORRECT THE INTERFERENCE AT HIS OWN EXPENSE.

CAUTION: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED

BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER'S
AUTHORITY TO OPERATE THE EQUIPMENT.

THIS CLASS A DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003.
CET APPAREIL NUMÉRIQUE DE LA CLASSE A EST CONFORME À LA NORME

NMB-0 03 DU CANADA.

WARNING: This is a Class A product. In a domestic environment this product

may cause radio interference in which case the user may be required to take
adequate measures.

4

IMPORTANT SAFEGUARDS

1. Read t hese instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the
manufacturer's instr u ctio ns.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or

other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug.
A polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and a third grounding prong.

The wide blade or the third prong are provided for your safety. If the provided plug
does not fit into your outlet, consult an electrician for replacement of the obsolete
outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specif ied by the manufa ct ur er.

12. Use only with the cart, stand, tripod, bracket, or table specified by the

manufacturer, or sold with the apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid injury from t ip-over.

13. Unplug this apparatus during lightning storms or when unused for l ong peri ods of

time.

14. Refer all servicing to qualified service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been moisture, does not operate normally, or has been
dropped.

15. CAUTION THESE SERVICING INSTRUCTI ONS ARE FOR USE BY QUALIFIED

SERVICE PERSONNEL ONLY. TO REDUCE THE RI S K OF E LECTRIC SHOCK
DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN
THE OPERATING INSTRUCTIONS UNLESS Y OU QRE QUALIFIED TO DO SO.

16. Use Certified/Listed Class 2 power source only.

5

TABLE OF CONTENTS

1. INTRODUCTION ---------------------------------------------------------------------- 6

1.1 THE CAMERA FEATURES ---------------------------------------------------- 6

2. SYSTEM INSTALLATION ----------------------------------------------------------- 7

2.1 PACKAGE CONTENTS --------------------------------------------------------- 7

2.2 OPERATION REQUIREMENTS ---------------------------------------------- 7

3. Parts Name & Function -------------------------------------------------------------- 8

4. Connection ------------------------------------------------------------------------------ 9

4.1

COLOR LEAD WIRE & CO LOR DISPLAY LABEL ------------------- 9

4.2 EXTERNAL INPUT --------------------------------------------------------------- 10

4.3 EXTERNAL OUTPUT ----------------------------------------------------------- 10

4.4

RS-485 CONNECTION -------------------------------------------------------- 10

4.5 EXTERNAL LENS CONTROL ------------------------------------------------ 11

4.6 EXTERNAL A/ D KE Y C ON TROL --------------------------------------------- 11

5. CAMERA ADJUSTMENT------------------------------------------------------------ 12

5.1 OSD MAIN SCREEN ------------------------------------------------------------ 12

5.2 MAIN MENU ----------------------------------------------------------------------- 12

6. TROUBLESHOOTING AND MAINTENANCE ---------------------------------- 18

6.1 TROUBLESHOOTING ---------------------------------------------------------- 18

6.2 MAINTENANCE ------------------------------------------------------------------ 18

7. DIMENSIONS -------------------------------------------------------------------------- 19

8. SPECIFICATIONS ------------------------------------------------------------------- 20

6

1. INTRODUCTION

The 22x Auto Focus Zoom WDR Day & Night Camera provides especially for closed
circuit television (CCTV) and security surveillance application.

1.1 THE CA ME RA FEATURES

• SONY 1/4" 960H Super HAD CCD II (700 TV Lines)

• 352x zooming capability (Optical : 22x / Digital : 16x)

• 0.1 lux (Color), 0.01 lux (B/W), 0.00001 lux(slow shutter)

• Excellent picture quality

• Various picture effects

• Support camera control available RS-485

• power operation DC 12V

CAUTION : Use Certified/Listed Class 2 power source only.
Use at the 12VDC Adapter must provide the power consumption of above

500MA.

• Function :

- D/N (Day / Night)

- DSS (Digital Slow Shutter)

- DIS(Digital Image stabilizer)

- WDR (Wide Dynamic Range)

- DNR (Digital Noise Reduction)

- M/D (Motion Detection)

- AWB (Auto White Balance)

- AE (Auto Exposure)

- AGC (Auto Gain Control)

- BLC (Back Light Compensation)

- OSD (On Screen Display)

- ZOOM PRESET & TOUR

- P/M(Privacy Mask)

- ALARM(Alarm out)

IMPORTANT : The user of this camera is responsible for checking

and complying with local, state, and federal laws and statutes
concerning the recording and monitoring of audio signals.

7

2. SYSTEM INSTALLATION

Installation of the camera must be performed by qualified service personnel in
accordance with all local national electrical and mechanical codes must perform
installation of the camera.
Perform the following steps to install the ca mera.

2.1 PACKAGE CONTENTS

• Camera - 1EA

• Instruction Manual (This document) - 1EA

• 12 pin Interface Cable – 1EA

• Camera Mounting Bracket (option)

• A/D Remote Controller (option)

2.2 OPERATION REQUIREMENTS