Eneo MED-62V2812M0A, MEB-62F0036P0A, MEB-62V2812P0A User Manual

EN

User Manual

1/2.8” HD Dome,

Fixed,

Day&Night, 1920x1080, 12VDC,

2.8-12mm, Infrared, IP66

MED-62V2812M0A

Safety Precaution

03

ULTRA CLEAR RESOLUTION CAMERA

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To prevent electric shocks and risk of fire hazards, do NOT use other than
specific power source.

The symbol is intended to alert the user to the presence of important
operating and maintenance(servicing) instructions in the literature
accompanying the unit.

The symbol is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.

Warning :

This equipment has been tested and found to comply with the limits for a Class

A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.

Caution :
Any changes or modifications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user's authority
to operate the equipment.
Mains power quality should be that of a typical commercial environment. If the user
of the model requires continued operation during power mains interruptions, it is
recommended that the model be powered from an uninterruptible power supply
(UPS) or a battery.

ULTRA CLEAR RESOLUTION CAMERA

Safety Precaution

04

NOTICE

The image used in this instruction manual are processed to help comprehension
and may differ from actual video of the camera.
Avoid installing areas where has shock or vibration which results in the problems.

Pay attention to safety when laying the connection cable and observe that the cable
is not subjected to heavy loads, kinks or damage and no moisture can get in.
Never open the device such as boards or lens.
The warranty becomes void if repairs are undertaken by unauthorized persons.
Maintenance and repair have to be carried out only by authorized service centers.
Use only a mild detergent to clean the housing.
The camera should never be operated beyond the technical specifications.
This can lead to destruction.
The camera should never be operated in water.

ULTRA CLEAR RESOLUTION CAMERA

Contents

05

Safety Precaution

p.03~04

Contents

p.05

Features

p.06

Composition

p.07

Dimensions

p.07

Part Names

p.08

Installation Instructions

p.09~10

Operating Instructions

p.11~28

Specifications

p.29~30

ULTRA CLEAR RESOLUTION CAMERA

Features

Key Features

06

• 1/2.8” SONY Exmor CMOS sensor

• 1080P TVI mode, CVI mode, AHD Video or 960H CVBS Video Selectable

• TVI mode/CVI mode/AHD Video Transmission Distance over Coax.; 500M

• Automatically removable IR Cut filter by Dual filter switcher

• Built-in f=2.8~12mm F1.4 Mega pixel DC Auto Iris Vari-focal lens

• Sensitivity of Color 0.3 Lux / BW 0.005 Lux (@IRE 40, Sens-up On, IR Off)

• D-WDR (Wide Dynamic Range)

• Improved noise reduction 2D+3DNR(TVI mode/CVI mode/AHD), 2DNR(CVBS)

• FOCUS ASSIST for Error free focus adjustment

• 2 Auto(AE/AWB) control

• LSC (Lens Shading Compensation)

• DPC (Defective Pixel Compensation)

• Motion detection, Privacy mask, BLC/HSBLC, Defog, Sens-up(~x30),

Mirror/Flip, Freeze, Negative Image, IR Smart, Cam Title

• OSD MENU & CVBS output for easy installation & maintenance

• Built-in 30pcs IR-LED

• One-side Anti-scratch hard coated clear bubble

• Zoom & Focus Adjustment

• 3-Axis gimbal

• IP66 Protection

• Power: DC12V

07

Composition

Dimensions

(unit : mm)

ULTRA CLEAR RESOLUTION CAMERA

Video Sub-out

Cable (1pc)Mounting Template

Mounting Screw:
4 x 24mm (4pcs)

Plastic Anchor:

6.5 x 26.5mm (4pcs)

Camera

Operating Instruction

Ø144

Ø100

108

60

L-Wrench (1pc)

ULTRA CLEAR RESOLUTION CAMERA

Part Names

08

Video sub-out
Connector

3-Axis
Gimbal

Dome Cover

Bubble Dome

Dome Base

Zoom lever

Focus lever

Power Cable

OSD Control &
Video format Joystick

Video format DIP Switch

CVBS

HD

ULTRA CLEAR RESOLUTION CAMERA

Installation Instructions

09

• Extreme care should be taken NOT to scratch the bubble dome surface while
the camera installing or adjusting.

• Care should be taken the cable is NOT to be damaged, kinked or exposed in
the hazardous area.

• Do not expose the camera directly to a strong light source such as the sun or
spot light.

CAUTION

Mounting Screw

(4x24mm)

Plastic Anchor

(6.5x26.5mm)

1. Drill four holes for mounting on the ceiling or wall.

2. Place the dome base at the pre-drilled installation position and fix it by using
mounting screws.

3. Route the Power/BNC cable to the connecting place.

4. Adjust the camera’s viewing angle (Pan, Tilt, Rotation)

5. Assemble the dome cover to the dome base unit.

ULTRA CLEAR RESOLUTION CAMERA

Installation Instructions

10

Zoom & focus adjustments

Limit of Pan & Tilt

1) Pan limit:
Adjusts the first pan angle by turning

the gimbal 360˚.

2) Tilt limit:
Tilt is limited to 25°min ~ 90°max. with
reference to the ceiling when the
inclination of camera module is 0°, that
is, the image is aligned horizontally.

3) Rotation limit
(Horizontal image alignment):
Adjust the rotation angle by turning
the upper gimbal 360°.

Pan

Tilt

Rotation

• Be careful with the cable twisting
during pan or tilt adjustments.

CAUTION

25º

90º

• To widen the viewing angle, turn the Zoom
to “W”(Wide) and to obtain a closer view,
turn it to “T”(Tele)

•

Turn the Focus lever to “N”(Near) or “∞”(Far)

until the sharpest focus is made.

Power Supply Connections

Camera can be operated with the regulated
or unregulated DC12V but the regulated power
supply of DC12V is recommended.
Camera is protected from the damage by the
reverse connection of polarity.

VIDEO (BNC)

POWER ( )

Zoom

Focus