Eneo GLC-1401 Installation And Operating Manual

Installation and Operating Manual

LAN Camera GLC-1401

Contents

1. Safety Instructions ..............................................................................................................................................3

2. Product Features ................................................................................................................................................

2.1 Product Introduction ...........................................................................................................................................

2.2 General Description ............................................................................................................................................

3. Description of the Front/Rear View ......................................................................................................................

3.1 Front Panel and Rear Panel .................................................................................................................................

3.2 RS-232 Port & ALARM I/O ...................................................................................................................................

3.3 Flank Panel ........................................................................................................................................................

3.4 The USB Function ...............................................................................................................................................

4. Installation..........................................................................................................................................................9

4.1 Connecting with an NVR .....................................................................................................................................

4.2 Connecting with a DVR .....................................................................................................................................10

4.3 Connecting with a Multiplexer ..........................................................................................................................10

4.4 Updating System Software ...............................................................................................................................

4.5 LAN CAMERA SD Card Troubleshooting .............................................................................................................

4.6 Adjustment of Lenses .......................................................................................................................................13

5. Network Conﬁguration ......................................................................................................................................14

5.1 Cable Connections ............................................................................................................................................14

5.2 Conﬁgure your LAN CAMERA Network Settings .................................................................................................16

5.3 TCP/IP Communication Software ......................................................................................................................17

5.4 TCP/IP Installation ............................................................................................................................................18

5.5 TCP/IP Conﬁguration Setting .............................................................................................................................19

5.6 Connection Testing ...........................................................................................................................................20

6. Operating Instructions for Image Software and Network ...................................................................................

6.1 Microsoft Internet Explorer

................................................................................................................................23

6.2 The LAN CAMERA IP Surveillance .....................................................................................................................

7. Advanced Operation .........................................................................................................................................

8. Speciﬁcations ...................................................................................................................................................69

9. Function of Client PC ........................................................................................................................................71

10 Dimensional Drawings ......................................................................................................................................71

APPENDIX 1 - SCAN IP ..............................................................................................................................................72

APPENDIX 2 - LANCAM UPnP How To ........................................................................................................................

APPENDIX 3 - The ARP Function ................................................................................................................................

APPENDIX 4 - Register as a DDNS Member ...............................................................................................................

APPENDIX 5 - MPEG4 Bit Rate Lookup Table of LAN Camera .....................................................................................91

APPENDIX 6 - FAQ

.....................................................................................................................................................92

APPENDIX 7 - Pin Assignment of the 30 Pin Main Connector of the Camera Packs

VHM LAN01, VHM LAN02, VHM LAN03 and VHM LAN04 ......................................................................93

1. Safety Instructions

• The instructions below must be followed for your own safety.

• Please read the safety instructions and operating instructions before connecting the device and putting it into operation.

• Keep the operating instructions safe for use at a later date.

• Never operate the camera outside of the speciﬁcations as this may prevent the camera functioning.

• Never point the camera towards the sun with the lens open as this may prevent the sensor functioning.

• When laying the connection cable, it is essential to follow the instructions below: the cable must be laid in such a way that it is not strained, bent or damaged and no moisture can penetrate.

• To prevent ﬁre or shock hazard, avoid exposing this unit to rain or moisture.

• Do not block ventilation openings.

• Installation and maintenance of the system may only be carried out by persons with appropriate authorisation for this and in accordance with the installation instructions - taking into account all the applicable standards and guidelines.

• The installer is responsible for maintaining the protection class.

• Only use rust-proof screws should be used to mount the housing and camera outside.

• Do not place anything on top of the unit that might spill or fall into it.

• Only original spare parts from the manufacturer.

2. Product Features

2.1 Product Introduction

This user-friendly device combines cutting-edge sophistication with practical reliability and convenience, high performance with smooth remote communication. Just plug in the network cable ! You’ll get live streaming Video & Audio anytime any place ! You’ll have security you can rely on ! The especially high resolution has 480 TV lines, a built-in web server and a Network interface to connect you with the Internet securely and fast.

Other special features include the masking of personal private images with ﬂexible mask-area positioning and size, the self-downloading automatic video codec and other components, and the whole unit is very easy to set up. You can access the network to get smooth images through the real-time and synchronized audio / visual stream provided by the device, because it supports two compression modes, the MJPEG and the MPEG4 - you can change from one to the other as you wish. The MPEG4 ﬁle format is a very small size ﬁle, so it can save more images over a longer time and can be set extremely fast. The device also has a built-in website server providing many Internet functions and protocols, including the MDIX protocol which recognizes both the normal and the crossover cables, either of which can connect up with a LAN camera.

We hope this device makes it easier for you to get your IP address information. This unit supports the USB interface which helps you to very easily get an IP address to open the IE browser: Just type in your IP address to the browser and you can access your LAN camera.

The device can hopefully provide the advanced motion detection function to improve your network surveillance with both the powerful and enhanced multi-zone and multi-sensitivity modes of detection. We believe this unit is the right answer to all your network surveillance problems. Try it and you’ll see.

2.2 General Description

• 1/3” CCD Colour Camera with C/CS Mount

• Horizontal Resolution of 480 TV Lines

• Automatic Shutter Control (AES)

• MJPEG and MPEG-4 Video Compression

• Simultaneous Video and Audio Signal Transmission

• E-Mail and FTP Transmission of Important Events

• Integrated Activity Detection

• Ethernet Interface: 10/100Base-TX

• Supports Various Network Environments

• Alarm In/Output, Audio Output

• Upgrade via SD Card, USB Interface and Network

• SD Socket for Local Video Storage by SD Cards

3. Description of the Front/Rear View

3.1 Front Panel and Rear Panel

Front Panel

Rear Panel

1. Microphone:

The LAN CAMERA has an additional audio function. The device has a microphone built into its front panel which records sound.

2. ALARM I/O & RS-232 Port:

The RS-232 communication port functions as a connector to an external control device. This port includes ALARM OUT, GROUND, ALARM IN, and ALARM RECOVER for connecting with external devices.

WARNING: You can’t use general RS-232 cables to link up with the I/O connectors in the rear panel of

the device (please see the next page for further details).

3. VIDEO OUT Connector:

The connector provides the unit’s composite video signals to a monitor.

4. Plug Inlet:

A 5VDC inlet that connects to an external power supply.

5. ETHERNET 10/100 Connector:

This is a standard RJ-45 connector for 10/100 Mbps Ethernet networks.

3.2 RS-232 Port & ALARM I/O

1. RS-485 D-

2. RX: This pin is one of the RS-232 pins. It connects with the TX pin of another device.

3. TX: This pin is one of the RS-232 pins. It connects with the RX pin of another device. Please refer to the note

below on the standard RS-232 9 Pin Cable with Pin 2 and Pin 3 exchanged; see the pin conﬁguration chart below for details.

4. RS-485 D+

5. GND: Ground contact.

6. ALARM RESET (INPUT): This pin connects to an alarm-clear device for clearing an alarm. (

5V, 20mA 0V(Active)

)

7. ALARM IN (INPUT): This is an alarm input that can be programmed in the menu system to active low. (

5V, 20mA 0V(Active)

)

8. ALARM OUT (OUTPUT): This is an alarm output trigger. Connect this to external devices such as buzzers or lights. (

5V, 20mA 0V(Active)

)

9. AUDIO OUT: This provides the unit’s audio signal to a speaker.

The pin conﬁguration chart:

1. Lens Mount: This LAN CAMERA is used with either C or CS mount lens.

2. ALC VR: Iris control VR

When an auto iris (DC Drive) lens is used, this VR is used to adjust the iris for different lighting environments. Adjust the VR clock-wise to open the iris and counter-clockwise to close the iris of the camera.

3. RESET: Recover to factory default.

4. IRIS: Auto iris connector

This camera works with a DC drive auto iris lens. Please refer to the pin assignment marked on the camera when connecting the auto iris lens.

1. AES: Auto electric shutter

2. DC IRIS: Use auto iris (DC drive)

3. DHCP: Turn On / Turn Off use DHCP protocol. If the switch points upwards, the device can

change the setup of network function (enable/disable) via the network.

4. STATIC IP: If the switch points down, the device can’t obtain an IP address from the DHCP server. This option is needed to conﬁgure the network communication settings.

3.3 Flank Panel

Right Flank Panel

Left Flank Panel

1 2 3 4

– + + –

CONT DRIVE

5. DIP Switch:

6. POWER Indicator: Indicates the power status of the unit. The green light indicates the unit is activating.

The red light indicates the power is on and the SD card cannot be removed.

7. LAN Indicator: Indicates the LAN status of the unit. The green light indicates the 100 Mbps Ethernet network is activating. The red light signals the LAN is data linking.

8. RS-485 Port: The RS-485 communication ports function as connectors when two or more units are serially connected to an external control device.

9. 5 pin MINI USB Port: The user can use a USB device cable to connect the LAN CAMERA to the USB port on the PC.

10. SD CARD Slot: This is used for system software updating and archiving / accessing critical images.

3.4 The USB Function

By connecting the LANCAM with a PC via the USB connector, the LANCAM can provide two different functions.

Insert an SD card: As a card reader

Insert an SD card into the LAN CAMERA, then connect to the PC. You might transfer ﬁles between the SD card and the PC. Once you’ve connected your LAN CAMERA to your computer, the Windows system will detect the connection and ask you what you want to do with your SD card.

In another words, if the user connects the LAN CAMERA with an SD card and the PC via the USB connector, the LAN CAMERA can be used as a normal card reader.

Remove an SD card: As a conﬁguring tool

Before using the USB conﬁguration setting page, please remember to remove the SD card or your PC will read the SD card and won’t show this window.

Network Setting

PPPoE Setting

DHCP ON

DHCP OFF

WARNING: After changing the settings, please click the „Apply” button. All of the options will be effective after removing the USB connector.

4. Installation

Please follow the instructions and the diagram below to set up the system.

NOTE: The LAN CAMERA is linked by its Video Out connection via a BNC connector to a monitor’s Video In connection. If this connection is there, you can see some information on the monitor screen, such as the LAN CAMERA factory default Static IP address (192.168.1.168). But the LAN CAMERA Static IP address can only appear if there is a connection between the LAN CAMERA and another device. If there is no such connection, the LAN CAMERA factory default Static IP address will not appear on the monitor screen.

4.1 Connecting with an NVR

Use a crossover LAN cable to connect directly to an NVR.

CONNECT TO ETHERNET

RJ-45 CONNECTOR

CONNECT TO

NVR ETHERNET PORT

CONNECT TO VIDEO OUT

BNC CONNECTOR

CONNECT TO DVR VIDEO IN

4.2 Connecting with a DVR

TO LAN Camera VIDEO OUT

BNC CONNECTOR

LAN CAMERA 1

LAN CAMERA 2

LAN CAMERA 16

4.3 Connecting with a Multiplexer

4.4 Updating System Software

If the system software of the LAN CAMERA needs to be upgraded, please take the following steps to safely process it.

Important: Before carrying out the following procedures, please ensure the SD card is working and the ﬁle of system ﬁrmware is intact.

1. Format an SD card using the FAT16 format if it is unformatted; there are no limitations to an SD card’s capacity.

2. Create a directory named LANCAM in the SD card if it does not exist.

3. Copy the ﬁle of UPDATE.BIN to the LANCAM-directory.

4. If the LANCAM is running, please power it off ﬁrst.

5. Insert the SD CARD into the LANCAM.

6. Remove the Ethernet cable from the RJ-45 port and then power on the LANCAM.

7. In 5 to 10 seconds, a message reading „UPDATE PROCESSING” will show up on the screen on a blue back ground; if not, please check out steps 1 to 6 carefully or else inform your technical support while ignoring the following steps.

8. DO NOT power off the LANCAM while this update process is running until the message „UPDATE OK RESET PLEASE” appears on the screen; it might take 15 to 30 seconds to appear.

9. If the message „UPDATE NG RESET PLEASE” appears rather than „UPDATE OK RESET PLEASE”, please write down the error messages shown on the screen and inform your technical support, while ignoring the following steps.

10. Power off the LANCAM when this update process is ﬁnished, then remove the SD card from the LANCAM.

11. Reconnect the Ethernet cable to the RJ-45 port if necessary.

12. Power ON the LANCAM and it will work normally if the entire update procedure goes correctly.

13. Verify the version of the system software.

WARNING:

1. Don’t use FAT32 or NTFS or other ﬁle formats in step 1.

2. Steps 1 to 3 have to be done on a PC.

3. Make sure the ﬁle of UPDATE.BIN is a correct one in step 3, or the LANCAM will not work normally after being updated.

4. If the power of the LANCAM is suddenly lost in step 8, please remove the SD card ﬁrst and turn on the LANCAM next to test its operation. If the LANCAM remains working normally, please go back to step 4; otherwise, please inform your technical support.

5. In step 10, if the SD card is not removed and the LANCAM does not get online as well, the updating process must be repeated again after rebooting the LANCAM.

6. Make sure that the SD card is inserted in a correct position in step 5, or the LANCAM will suffer permanent physical damage.

7. If the message „CSUM ERROR” appears in step 8, it implies a problem in the ﬁle of UPDATE.BIN.

8. Don’t interrupt the process while the unit is updating itself; proceed with an SD card not including any system software of the unit, or else the unit will crash.

4.5 LAN CAMERA SD Card Troubleshooting

1. Check if the SD card position is correct or not. Please refer to the manual for the related information.

2. After powering the LAN CAMERA on, correctly insert the SD card, and a little icon of „SD” will show up in the upper-right corner of the monitor screen. If not, it means the device detection has failed. Please contact your technical support and ignore the following steps.

3. If no cross sign appears beside the „SD” icon, please go on to the next step. If a cross sign appears, please check the following:

a. Is it really an SD „Memory” Card?

b. Is this SD card formatted in the FAT16 format?

c. Connect the SD card with a PC and test to see whether the PC can read the data or not.

d. Does this SD card still have the capacity for storing data?

e. Is the SD card set to write?

If all the answers are „yes” but the cross sign still persists, please contact your technical support and ignore the following steps.

4. Please make sure the function of „SD CARD ENABLE” is activated in the ALARM and SCHEDULE pages if no cross sign appears beside the „SD” icon on the screen.

5. After recording, read the data on the web page of „sdget.htm”. If the data cannot be read through the network, please read it instead in a PC, check the data stored in the „LANCAM” directory and contact your technical support regardless of whether there is data or not.

WARNING:

1. Performing this troubleshooting process may need a monitor, a PC, a card reader and some cables.

2. If the SD card is removed while storing or accessing data, the data will be lost.

3. If there is a cross sign beside the „SD” icon, it means the SD card has been inserted into the LAN CAMERA but cannot perform its writing function. Possible reasons are:

a. It is not an SD memory card.

b. The SD card is unformatted or formatted in a non-FAT16 or non-FAT12 format.

c. The ﬁle system is damaged.

d. The capacity of the SD card is full.

e. The SD card is set to be read only.

4. Turn off the power before inserting the SD card. Otherwise the unit may shut down.

C mount lens

CS mount lens

4.6. Adjustment of Lenses

Adjustment of ﬂange focus for ﬁxed focus lenses

This adjustment (distance between lens casing and sensor surface) is required if a sharp deﬁnition cannot be obtained with the lens focussing, or in order to adjust the

∞ position

To obtain a sharp deﬁnition, point the camera at an object which is at least 2000 times further away from the front of the lens than the focal length. (If the focal length is 7.5mm, the object must be at least 15m distant from the camera).

Open the aperture fully and set the focus to

∞ (inﬁnite).

If the lens has automatic exposure control, select a dark object, or better use an ND ﬁlter (64-x) to ensure that the aperture is fully open.

Undo set screw

M. Turn the lens with the CS mount connection until the deﬁnition is sharp.

When ﬁnished, retighten screw

Adjustment of ﬂange focus for variable focus lenses

To obtain a sharp deﬁnition, point the camera at an object which is at least 5 times the minimum lens distance (MOD) of the lens. (If this is 1m, the object must be at least 5m distant from the camera).

Open the iris fully and set the lens to the maximum tele position and focus with the focus ring.

If the lens has automatic iris control, select a dark object (or use an ND ﬁlter, 64-x) to ensure that the iris is fully open.

Set the lens to the maximum wide-angle position.

Undo set screw

M and turn the C/CS ring on the camera until an optimal sharpness is

reached. Repeat the process for checking purposes, if necessary.

When ﬁnished, retighten screw

Note

The value stated in the diagram as AL (depth of thread of the lens with CS mount: <- 5mm) must be observed. The camera may be damaged if this value is exceeded.

When installing a lens with CS mount, never use the C-mount adapter ring.

Addition when using cameras for day/ night application

Even if the lens is IR corrected (0-focus shift), a minor ﬂange focus is possible between visible light and IR light.

If there is a day/night application with IR illumination, the ﬂange focus should be set under IR light conditions. This is because the iris is generally opened when used at night due to the poor level of light and low depth of focus. During the day, the iris is continuously closed further, there is a greater depth of focus and the difference in the ﬂange focus is compensated.

Explanation of terms for iris setting

AGC (automatic gain control)

This starts tooperate when the light intensity is insufﬁcient to deliver a full video signal (1Vp-p). The greater the gain, the greater the signal noise in the picture. It is generally activated between 0.8 and 1.0Vp-p.

White clip

Signal limitation at high image amplitudes. The white clip value generally lies between

1.1 and 1.2 Vp-p.

AES (automatic shutter control)

This automatically controls the shutter times, it starts when the light intensity becomes stronger and the signal would otherwise be limited/over-regulated by the white clip feature. Automatic shutter control is mainly applied for manual lenses.

If a camera is operated with controlled lenses, regardless of whether DC or AI, the AES must be switched off. Problems arise if this is not done because both control systems try to steer the volume of light for the camera. As the AES generally reacts faster, the iris remains fully opened and the shutter resumes the control work, which produces major drawbacks. As the iris is open, the depth of focus is very low. When shutter times are short, this can cause a smear effect (bright, vertical stripes in light parts of the picture).

Iris adjustment

The working point of the iris should always be above the AGC start and below that of the white clip. This range is very small with some cameras, making it difﬁcult to adjust the lens. It is therefore advisable to switch off the AGC (if possible) when adjusting the iris. Once the lens has been focussed, the AGC must be switched back on (only for cameras which allow the AGC to be switched off).

In the case of DC lenses, the working point of the iris is adjusted at the camera’s level potentiometer (the AI ampliﬁer is built into the camera).

In the case of AI lenses, the level potentiometer is located on the lens (the AI ampliﬁer is built into the lens).

5. Network Conﬁguration

5.1 Cable Connections

Please follow the instructions below to connect your LAN CAMERA to a computer or a network and to choose a proper RJ-45 cable conﬁguration for connections.

Physical speciﬁcation of RJ-45 cable for Ethernet

Wire Type Cat. 5

Connector Type

RJ-45

Max. Cable Length

100m

Switch/Hub Wiring Conﬁguration

Straight Through

PC Wiring Conﬁguration

Cross Over

5.1.1 Connect to a Computer

Use a crossover LAN cable to connect directly to a computer.

CROSSOVER CABLE PIN CONFIGURATION

CROSSOVER CABLE

TO PC LAN CARD

5.1.2 Connect to a LAN Hub (INTRANET)

The RJ-45 PIN conﬁguration for connecting with a LAN Hub is shown below.

TO NETWORK

TO PC NETWORK CARD

HUB/Switch / Router

5.2 Conﬁgure your LAN CAMERA Network Settings

Upon connecting with the network hardware, you need to activate the network function and conﬁgure the proper network settings of the LAN CAMERA.

5.2.1 Enable DHCP Function

This function can only work if the LAN, which the unit is connected to, has a DHCP server. If the DHCP server is working, please move the dip switch points up to 3 on the ﬂank panel; now the LAN CAMERA will obtain an IP address automatically from the DHCP server. In that case, please skip section 5.2.2 (Set IP address) and follow section 5.3 (TCP/IP Communication Software).

5.2.2 Set IP Address

You need to set an IP address for the unit if the LAN unit isn’t connected to a DHCP server. Otherwise, please follow the instructions given below:

Set the

IP, SUBNET MASK and GATEWAY. The following is a sample setting.

IP: 192.168.1.X

SUBNET MASK: 255.255.255.0

GATEWAY: 0.0.0.

NOTE: When only one unit of the LAN CAMERA is connected to a computer or LAN, you can freely assign an IP address for the LAN CAMERA. For example, there are a range of LAN CAMERA IP addresses from

192.168.1.1 to 192.168.1.255. You can pick one for use from the range of the IP. It’s not necessary to set MASK and GATEWAY; leave the settings as default.

When a LAN CAMERA is connected to a WAN, you must acquire a unique, permanent IP address and correctly conﬁgure the MASK and GATEWAY settings according to your network architecture. If you have any questions regarding those settings, please contact a qualiﬁed MIS professional or your ISP.

NOTE: When connecting to a network, each connected LAN CAMERA must be assigned a unique IP, which must be in the same class type as your network address. IP addresses are written as four sets of numbers separated by periods; for example, 192.168.1.1 Therefore, if the connected network is identiﬁed as Class C, for example, the ﬁrst three sets of numbers of the LANCAMERA IP address must be the same as the network address. If the connected network is identiﬁed as Class B, the ﬁrst two sets of numbers of the LAN CAMERA IP address must be the same as the network address. If you have any questions regarding these settings, please contact a qualiﬁed MIS professional or your ISP.

5.3 TCP/IP Communication Software

Follow the instructions below to install the TCP/IP communication program into your computer.

Click the

Start menu from your computer, and point to the Settings/Control panel.

Double click the

Network icon to enter the windows.

Click the Conﬁguration tag, and check if the TCP/IP is included among the network components list. If the TCP/IP is included, please process section 4.5. If it is not included, please follow section 4.4 to install the TCP/IP.

During the installation, you will be requested to insert the Windows CD-ROM. After installation, the PC may be restarted.

5.4 TCP/IP Installation

5.5 TCP/IP Conﬁguration Setting

Click Start –> Settings –> Control Panel –> Network

Select

TCP/IP, and then click Properties.

Before processing the LAN CAMERA installation in a WAN, please make sure the Internet connection works properly. If not, please contact your ISP provider.

If you are using a DHCP server, please select

Obtain an IP address automatically. Any assigned IP address for the connected LAN CAMERAs must be in the same class type as the server. If there is no DHCP server, please select specify an IP address and type in the IP address of your PC. This IP address must be different from the LAN CAMERA IP but in the same class type.

NOTE: The IP address of a LAN CAMERA in a network must be unique to itself as opposed to those of the other chosen PCs, but in the same class type.

5.6 Connection Testing

With the previous settings, follow the instructions below to ensure whether you have established the connection successfully.

Click

Start –> Programs –> MS-DOS Prompt

Type in

ping 192.168.1.168 then Enter. (See the sample screen below)

• This IP is the LAN CAMERA IP address that is assigned for the connected LAN CAMERA in step 2.

If you receive a response as in the sample screen below, you have successfully made the connection.

If you receive a response as in the sample screen below, the connection hasn’t been successfully established. Please re-check all the hardware and software installation by repeating steps 1 to 5. If you still can’t establish the connection after re-checking, please contact your dealer.

6. Operating Instructions for Image Software and Network

Two choices of software are available for linking up with the LAN CAMERA: (1) the Microsoft Internet Explorer; and (2) the LAN CAMERA VIEWER, a network browser in a PC which provides the functions of monitoring remote zones or watching recorded data through the TCP/IP protocol.

The details are listed as follows.

System Requirements

• Intel Pentium 233MHz processor or above

• At least 256MB RAM

• Windows 95, 98, NT, 2000 and XP (XP, if installed with virtual machine)

• 4MB VGA card capable of 24-bit true color display

• 20MB free hard-disk space for software installation

• 10/100 Base-TX network for LAN operation

• The Microsoft Internet Explorer 5 above

Wire Type Cat. 5

Connector Type

RJ-45

Max. Cable Length

100m

Switch/Hub Wiring Conﬁguration

Straight Through

PC Wiring Conﬁguration

Cross Over

RJ-45 PIN conﬁguration for Ethernet

Physical speciﬁcation for Ethernet

PIN NO. PIN Assignment

TX +

TX -

RX +

Not Connected

RX -

Not Connected

NOTE: For more details on network connections, please refer to the following document

RJ-45 socket

6.1 Microsoft Internet Explorer

6.1.1 Connecting the LAN CAMERA

1. Start up the Microsoft Internet Explorer, and then follow the steps below to connect the LAN CAMERA.

2. Click the URL block at the top of the window.

3. Enter the URL address of the LAN CAMERA into the URL block and press the

„Enter” button to enter the home page.

4. Scroll to the bottom of the page, with its ﬁve icons, „Image”, „Network”, „System”, „Application” and „SD Card”. Whichever you click, the page headlined „Enter Network Password” will appear.

5. Type in the „User Name” and „Password” in the appropriate spaces.

6. Click the

„OK” button to set your entries, and automatically exit the page.

NOTE: The default „User Name” and „Password” are admin and 9999 respectively.

NOTE: The page headlined „Enter Network Password” is shown below. Please enter the user name and password of the LAN CAMERA when you see it. If either the user name or the password is incorrect, please check the input data and rectify it if and as necessary.

NOTE: Once completed and passed, it will not appear again until you close the window and reconnect it.

NOTE: The initial sequence of proceeding is to type in your IP address and click the „Enter” button to access the home page. If and when you revise or change data in the „SYSTEM USERS” page, the sequence will alter to initially show the „Enter Network Password” page.

Browsing images from the LAN CAMERA

The images from the LAN CAMERA will be displayed on the home page while going online with the LAN CAMERA. Some buttons provided at the bottom of the home page for further setting. In MJPEG mode or in MPEG4 mode, there are different display formats of its home page.

• Click the

Image button to enter the image-setting page.

• Click the

Network button to enter the network-setting page.

• Click the

System button to enter the system-setting page.

• Click the

Application button to enter the application-setting page.

• Click the

SD Card button to open the SD Card- FILELIST of the MEMORY CARD window, if the SD card is inserted.

• Click the

Pan/Tilt button to change the Pan/Tilt/Zoom settings.

• Click the

button to change the time/date display mode.

• Click the

button to switch high/low speed network.

• Click the

button to play the live audio. Click once again to deactivate.

• Click the

button to archive AVI videos into your PC. Click once again to deactivate.

In the recording mode, there will appear a red twinkling icon

in the upper-right hand corner of the image. The AVI ﬁle will be saved in the path of c:\ LANCAM \ and its ﬁlename will be named as the format of Lancam_lancam_20051110134834.avi

• Digital zoom function: Click the left mouse button on the video display area, and it will show the zoom-in images. Double click the left mouse button to see the maximum size. Click the right mouse button on the video display area, and it will show the zoom-out images. Double click the right mouse button to come back to the normal size.

Homepage of MJPEG mode

Homepage of MPEG4 mode

6.1.2 Change Image Setting

Please follow the steps below to change the image setting through the network if and as necessary.

1. Click the

image button on the home page to enter the image-setting page.

Image setting page of MJPEG mode

Image setting page of MPEG4 mode

2. Adjust the image setting including „Device Title”, „Resolution”, „Quality”, „Frame rate” (MPEG4 mode only), „Format”, and „Viewer Type” (MJPEG mode only) if necessary.

3. Click the

Submit button to submit the new image setting.

4. Click the

Fine Tune button to enter the Image Fine Tune page to set the details of the device including:

„Brightness”, „Saturation” and „Sense Up”. Click the Default button to reset all the settings.

NOTE: The revised image will appear immediately after any change in made.

5. Click the Privacy Mask button to enter the Privacy Mask page.

6. Click the Home button to return to the home page while the new image setting acts on the images to effect the desired changes instantly. (If the setting has not been changed by the above steps, any (re)entry onto the home page will ﬁnd images in their earlier or original setting.)

Exchange the image format

1. Tick on one of the formats then press the

Submit button.

2. The LANCAM will restart automatically after several seconds.

Description of function keys

MPEG4 mode

Device Title: Type in the camera title in the given space.

Resolution: Scroll to choose the image resolution from „VGA” or „QVGA”.

Quality: Scroll to choose the image quality out of a spectrum of qualities ranging from „highest”, „high”, „medium”, and „low” to „lowest”. In MPEG4 mode, you can also set the quality by typing in the value. The custom quality value must be in the range between 64 Kbps to 8192 Kbps.

Frame rate: Click the drop-down list to choose the frame rates of „15FPS”, „24FPS” or „25FPS”.

Format: Click to choose the „MJPEG” or the „MPEG4” mode.

Fine Tune mode

Brightness: Enter your desired quality of image brightness from a spectrum of 0 to 255.

Saturation: Type in the saturation level in the blank (0 to 255).

MJPEG mode

Viewer type: Click to choose the viewer type of the „ActiveX” or „JAVA Applet” mode.

Submit: Click to submit the new image setting to the LAN CAMERA.

Default: Click this button to install the default settings in all the entries for image parameters on this page.

6.1.3 Change the Network Setting

Please follow the steps below to change the network setting through the network if and as necessary.

• Set the network options and IP address

1. Click the network button in the home page to enter the network-setting page.

2. The accessible networks here are the „FTP”

(MJPEG mode only), the „SMTP” (MJPEG mode only), the „SNTP”,

„DDNS” and the „PPPoE”.

3. Fill in the „IP Address”, „Netmask”, „Default gateway”, „Primary nameserver”, and „HTTP Port Number” if necessary.

4. Click the

Submit button to submit the new network setting.

5. Click the

Home button to return to the home page.

Description of function keys

IP Address: Enter the 4Byte IP Address in the appropriate blank space (the value in each box may be anywhere

between 0 and 255). Every LAN CAMERA has to own an IP address to be identiﬁed on the network.

Netmask: Fill in the 4Byte Subnet Mask in the required blank spaces (usually any numbers between 0 and 255). It is used to identify the subnet where the LAN CAMERA is sited.

Default gateway: Type in the 4Byte Gateway in the relevant blank spaces (each unit value must be between 0 and 255).

Primary nameserver: Enter the 4Byte DNS Server Address in the blank spaces provided (each value unit must be between 0 and 255). The DNS Server is in charge of translating the Domain Name into the IP Address.

HTTP Port Number: Indicates the speciﬁc HTTP Port Number. The default is 80.

Submit: Click to submit the new network setting to the LAN CAMERA.

• Change the Network Setting - FTP (MJPEG mode only)

Please follow the steps below to change the FTP setting via the network if necessary to upload recording data live.

1. Click the

FTP button at top left to enter the „FTP Server Setting” page.

2. Type in the „FTP Server” address, the „User Name”, and the „Password” of the FTP Server; and set the „Upload Path” of the image ﬁles when necessary.

3. Click the

Submit button to submit the new FTP setting of the recording.

4. Click the

Home button to return to the home page.

Description of function keys

FTP IP Address: Enter the FTP server DOMAIN NAME or IP address in the appropriate blank spaces.

User Name: Fill in the FTP user name in the attached blank space (if the data is not provided, warning messages will

show up).

Password: Type in the FTP password in the attached blank space (if the space is blank, warning messages will show up).

Upload Path: Enter the upload path while doing the FTP.

Submit: Click to submit the new FTP setting to the LAN CAMERA.

• Change the Network Setting - SMTP (MJPEG mode only)

Please follow the steps below to change the SMTP setting through the network if necessary.

1. Click the

SMTP button at upper left above to enter the „SMTP Server Setting” page.

2. Fill in the IP address of the SMTP server, and set the recipient’s e-mail address when and as necessary.

3. Click the

Submit button to submit the new SMTP setting.

4. Click the

Home button to return to the home page.

Description of function keys

SMTP Server: Enter the SMTP server DOMAIN NAME or IP address in the given blank space.

Email Address: The recipient’s e-mail address

Submit: Click to submit the new SMTP setting to the LAN CAMERA.

+ 65 hidden pages

Eneo GLC-1401 Installation And Operating Manual

Specifications and Main Features

Frequently Asked Questions

User Manual