Endress+Hauser Memocheck Sim CYP03D Operating Instructions Manual

0

BA00481C/07/EN/18.18
71416644
2018-09-30

Products Solutions Services

Operating Instructions

Memocheck Sim CYP03D

Testing tool for analysis measuring points

Declaration of Conformity Memocheck Sim CYP03D

Declaration of Conformity

2 Endress+Hauser

Memocheck Sim CYP03D Table of contents

Table of contents

1 About this document ........... 4

1.1 Warnings ........................... 4

1.2 Symbols used ........................ 4

2 Basic safety instructions ....... 5

2.1 Requirements for personnel ........... 5

2.2 Designated use ...................... 5

2.3 Occupational safety .................. 5

2.4 Operational safety ................... 6

2.5 Product safety ....................... 6

3 Device description .............. 9

3.1 Measuring system .................... 9

3.2 Simulation values ................... 10

4 Incoming acceptance and

product identification ......... 11

4.1 Incoming acceptance ................ 11

4.2 Product identification ................ 11

4.3 Certificates and approvals ............ 12

5 Electrical connection .......... 13

5.1 Connection in hazardous areas ........ 13

5.2 Connecting the simulator ............ 13

11 Repair .......................... 44

11.1 Spare parts ........................ 44

11.2 Return ............................ 44

11.3 Disposal ........................... 44

12 Accessories .................... 45

12.1 Memosens data cable ................ 45

12.2 Storage case ....................... 45

13 Technical data ................. 46

13.1 Environment ....................... 46

13.2 Mechanical construction ............. 47

Index ................................. 49

6 Operation options ............. 14

6.1 Overview .......................... 14

6.2 Structure and function of the operating

menu ............................. 16

7 Commissioning ................ 18

7.1 Switching on the measuring device .... 18

7.2 Setting the operating language ........ 18

7.3 Quick Setup ........................ 18

8 Operation ...................... 20

8.1 Configuring the measuring device ..... 20

8.2 Extended functions .................. 23

9 Diagnosis ...................... 43

10 Maintenance .................. 43

10.1 Cleaning ........................... 43

10.2 Battery replacement ................. 43

10.3 Calibration and qualification .......... 43

Endress+Hauser 3

About this document Memocheck Sim CYP03D

1 About this document

1.1 Warnings

Structure of information Meaning

DANGER

L

Causes (/consequences)

If necessary, Consequences of non­compliance (if applicable)

Corrective action

‣

WARNING

L

Causes (/consequences)

If necessary, Consequences of non­compliance (if applicable)

Corrective action

‣

CAUTION

L

Causes (/consequences)

If necessary, Consequences of non­compliance (if applicable)

Corrective action

‣

NOTICE

Cause/situation

If necessary, Consequences of non­compliance (if applicable)

Action/note

‣

This symbol alerts you to a dangerous situation.
Failure to avoid the dangerous situation will result in a fatal or serious injury.

This symbol alerts you to a dangerous situation.
Failure to avoid the dangerous situation can result in a fatal or serious injury.

This symbol alerts you to a dangerous situation.
Failure to avoid this situation can result in minor or more serious injuries.

This symbol alerts you to situations which may result in damage to property.

1.2 Symbols used

Symbol Meaning

Additional information, tips

Permitted or recommended

Not permitted or not recommended

Reference to device documentation

Reference to page

Reference to graphic

 Result of a step

4 Endress+Hauser

Memocheck Sim CYP03D Basic safety instructions

2 Basic safety instructions

2.1 Requirements for personnel

• Installation, commissioning, operation and maintenance of the measuring system may be

carried out only by specially trained technical personnel.

• The technical personnel must be authorized by the plant operator to carry out the specified

activities.

• The electrical connection may be performed only by an electrical technician.

• The technical personnel must have read and understood these Operating Instructions and

must follow the instructions contained therein.

• Faults at the measuring point may only be rectified by authorized and specially trained

personnel.

Repairs not described in the Operating Instructions provided must be carried out only
directly at the manufacturer's site or by the service organization.

2.2 Designated use

Memocheck Sim CYP03D is a test tool for analysis measuring points. It enables the simulation
of user-definable measured values and errors of all sensors incorporating
Memosenstechnology.

The main areas of application are:

• Chemicals and process engineering

• Food, pharmaceutical industry and biotechnology

• Water and wastewater treatment

• Hazardous areas

Use of the device for any purpose other than that described, poses a threat to the safety of
people and of the entire measuring system and is therefore not permitted.

The manufacturer is not liable for damage caused by improper or non-designated use.

2.3 Occupational safety

As the user, you are responsible for complying with the following safety conditions:

• Installation guidelines

• Local standards and regulations

• Regulations for explosion protection

Electromagnetic compatibility

• The product has been tested for electromagnetic compatibility in accordance with the

applicable European standards for industrial applications.

• The electromagnetic compatibility indicated applies only to a product that has been

connected in accordance with these Operating Instructions.

Endress+Hauser 5

Basic safety instructions Memocheck Sim CYP03D

2.4 Operational safety

Before commissioning the entire measuring point:

1. Verify that all connections are correct.

2. Ensure that electrical cables and hose connections are undamaged.

3. Do not operate damaged products, and protect them against unintentional operation.

4. Label damaged products as defective.

During operation:

If faults cannot be rectified:

‣

products must be taken out of service and protected against unintentional operation.

2.5 Product safety

2.5.1 State of the art

The product is designed to meet state-of-the-art safety requirements, has been tested, and
left the factory in a condition in which it is safe to operate. The relevant regulations and
European standards have been observed.

2.5.2 Safety instructions for electrical equipment in hazardous areas

The Memosens inductive sensor cable connection system consists of:

• Memocheck Sim (Memosens technology) CYP03D

• Measuring cable CYK10
Memosens is approved for measuring applications in explosive atmospheres in accordance

with:

• IECEx design approval, IECEx BVS 12.0007

• ATEX design approval BVS 12 ATEX E 008 with amendments
The EC Declaration of Conformity is an integral part of these Operating Instructions.

The Memocheck Sim CYP03D is powered by three alkaline batteries with a total nominal
voltage of 4.5 V.

Use only the following battery types!

‣

Type

Manufacturer Energizer

Type EN91

Designation LR6 (IEC)

U

battery, nominal

Chemical composition Zinc/manganese dioxide (Zn / MnO2)

Do not open the Memocheck Sim CYP03D in hazardous areas.

‣

6 Endress+Hauser

1.5 V

Memocheck Sim CYP03D Basic safety instructions

Before commissioning the Memocheck Sim CYP03D, make sure that the battery

‣

compartment is closed securely with a screw.
The maximum permissible cable length is 100 m (330 ft).

‣

Pay attention to the requirements for electrical installations in explosive atmospheres

‣

(EN/IEC 60079-14).
The conductive protective coating on the device is part of the Ex-related safety concept.

‣

Make sure that there is no damage >4 cm2 to the protective coating.

Hazardous area versions of digital sensors and simulators incorporating Memosens
technology are indicated by a red-orange ring on the plug-in head.

IECEx

Connecting the approved digital Memocheck Sim CYP03D sensor simulator to the IECEx­certified, intrinsically safe sensor output circuit of the Liquiline M CM42 (IECEx TUR

11.0007X) transmitter or alternatively to an IECEx-certified, intrinsically safe Memosens
sensor output:
Use only the following IECEx-certified measuring cables:
– CYK10-G*** (IECEx BVS 11.0052X)
– or a Memosens measuring cable that has IECEx certification and is identical in terms of

design, appliance technology and function.

The electrical connection must be made according to the wiring diagram.

‣

The transmitter's Memosens input must support the following maximum values. In

‣

particular, the effective inner inductance and the capacitance of the approved, intrinsically
safe sensor output may not exceed these values:

1. Entity Parameters

U0 = 5.1 V U0 = 5.04 V

I0 = 130 mA I0 = 80 mA

P0 = 166 mW (linear output curve) P0 = 112 mW (trapezoid output curve)

Ci = 15 μF Ci = 14.1 μF

Li = 95 μΗ Li = 237.2 μΗ

1) Ex-relevant electrical connection parameters

1)

2. Entity Parameters

1)

ATEX

Connecting the approved digital Memocheck Sim CYP03D sensor simulator to the ATEX­certified, intrinsically safe sensor output circuit of the Liquiline M CM42 transmitter or
alternatively to an ATEX-certified, intrinsically safe Memosens sensor output:
Use only the following ATEX-certified measuring cables:
– CYK10-G*** (BVS 04 ATEX E 121 X incl. amendments)
– or a Memosens measuring cable that has ATEX certification and is identical in terms of

design, appliance technology and function.

The electrical connection must be made according to the wiring diagram.

‣

Endress+Hauser 7

Basic safety instructions Memocheck Sim CYP03D

The transmitter's Memosens input must support the following maximum values. In

‣

particular, the effective inner inductance and the capacitance of the approved, intrinsically
safe sensor output may not exceed these values:

1. Entity Parameters

U0 = 5.1 V U0 = 5.04 V

I0 = 130 mA I0 = 80 mA

P0 = 166 mW (linear output curve) P0 = 112 mW (trapezoid output curve)

Ci = 15 μF Ci = 14.1 μF

Li = 95 μΗ Li = 237.2 μΗ

1) Ex-relevant electrical connection parameters

1)

2. Entity Parameters

1)

Temperature classes

Simulator Ambient temperature range T

Memocheck Sim CYP03D-**+** -20 to +50 ˚C (-4 to 122 ˚F) T4

a

Temperature class

If the ambient temperatures shown above are not exceeded no invalid temperatures for the
particular temperature class will occur at the simulator.

CSA

Pay attention to the documentation and control drawings for the transmitter.

‣

2.5.3 IT security

We only provide a warranty if the device is installed and used as described in the Operating
Instructions. The device is equipped with security mechanisms to protect it against any
inadvertent changes to the device settings.

IT security measures in line with operators' security standards and designed to provide
additional protection for the device and device data transfer must be implemented by the
operators themselves.

8 Endress+Hauser

Memocheck Sim CYP03D Device description

3

3 Device description

3.1 Measuring system

Sensor simulation in a complete measuring system consists of:

• Memocheck Sim CYP03D

• Transmitter with Memosens technology, e.g. Liquiline M CM42 or Liquiline CM44x

• CYK10 Memosens data cable

A0025995

 1 Measuring system with Memocheck Sim CYP03D

1 Liquiline CM44x transmitter
2 CYK10 Memosens data cable
3 Memocheck Sim CYP03D

Endress+Hauser 9

Device description Memocheck Sim CYP03D

3.2 Simulation values

With the Memocheck Sim CYP03D you can simulate the following data:

• Simulation values

– Main values
– Raw values
– Temperature

• Parameter

– pH glass (pH glass)
– pH glass, SIL sensor (pH glass SIL)
– pH ISFET (pH Isfet)
– ORP (ORP)
– pH + ORP combined sensor (pH + ORP)
– Conductivity conductive (Cond c)
– conductivity, conductive, 4-pin (Cond c 4-pol)
– conductivity, inductiveCond i)
– oxygen, amperometric (Oxygen (amp.))
– Oxygen, optical, Memosens (Oxygen (opt.Memo.))
– Oxygen, optical, fixed cable (Oxy. (opt.fixed))
– Chlorine (Chlorine)
– TurbidityTurbidity)
– Nitrate (Nitrate)
– SAC (SAC)

• The main simulation values can be selected as required within the context of the sensor

specification values

• Repeated ramp with any increment

• Error, e. g. glass breakage, alarm and warning

• Calibration values

You can freely configure all the values so that they match your process. The data listed above
are displayed on the transmitters.

10 Endress+Hauser

Memocheck Sim CYP03D Incoming acceptance and product identification

4 Incoming acceptance and product identification

4.1 Incoming acceptance

1. Verify that the packaging is undamaged.
 Notify the supplier of any damage to the packaging.

Keep the damaged packaging until the issue has been resolved.

2. Verify that the contents are undamaged.
 Notify the supplier of any damage to the delivery contents.

Keep the damaged goods until the issue has been resolved.

3. Check that the delivery is complete and nothing is missing.
 Compare the shipping documents with your order.

4. Pack the product for storage and transportation in such a way that it is protected
against impact and moisture.

 The original packaging offers the best protection.

Make sure to comply with the permitted ambient conditions.

If you have any questions, please contact your supplier or your local Sales Center.

4.2 Product identification

4.2.1 Nameplate

The nameplate provides you with the following information on your device:

• Manufacturer identification

• Order code

• Extended order code

• Serial number

• Ambient and process conditions

• Input and output values

• Safety information and warnings

Compare the information on the nameplate with the order.

‣

4.2.2 Product page

www.endress.com/cyp03d

4.2.3 Interpreting the order code

The order code and serial number of your product can be found in the following locations:

• On the nameplate

• In the delivery papers

Obtaining information on the product

1. Go to www.endress.com.

2. Call up the site search (magnifying glass).

Endress+Hauser 11

Incoming acceptance and product identification Memocheck Sim CYP03D

3. Enter a valid serial number.

4. Search.
 The product structure is displayed in a popup window.

5. Click on the product image in the popup window.
 A new window (Device Viewer) opens. All of the information relating to your

device is displayed in this window as well as the product documentation.

4.2.4 Manufacturer address

Endress+Hauser Conducta GmbH+Co. KG
Dieselstraße 24
D-70839 Gerlingen

4.2.5 Scope of delivery Memocheck Sim CYP03D

• Memocheck Sim CYP03D

• Operating Instructions

• 1 quality certificate as ordered

• Cable as per order (optional)

• Case to store CYP03D and cable (optional)

• Certificate of calibration (optional)

4.3 Certificates and approvals

4.3.1  mark

The product meets the requirements of the harmonized European standards. As such, it
complies with the legal specifications of the EU directives. The manufacturer confirms
successful testing of the product by affixing to it the  mark.

4.3.2 Ex approvals Memocheck Sim CYP03D

• ATEX II 2G Ex ia IIC T4 Gb

• IECEx Ex ia IIC T4 Gb

• CSA IS NI Cl. I, Div. 1&2, Group A-D

12 Endress+Hauser

Memocheck Sim CYP03D Electrical connection

II 2G

II 1G

II 3G

Ex ia

Zone 1

Zone 0

Zone 2

CYK10

CYP03D

not permitted

only with ATEX­Approval

GN/YE

YE

GN

BN

WH

GND

+

–

Com A

Com B

GY

5 Electrical connection

5.1 Connection in hazardous areas

A0026198-EN

 2 Operation in hazardous areas

5.2 Connecting the simulator

The electrical connection of the sensor's to the transmitter is established using measuring
cable CYK10.

 3 Measuring cable CYK10

Endress+Hauser 13

A0024019

Operation options Memocheck Sim CYP03D

2

3

4

5

6

6 Operation options

6.1 Overview

6.1.1 Display

1

Menu path and/or device designation

2

Battery status

3

Simulated parameter

4

Assignment of soft keys, e.g. menu

5

Assignment of soft keys, e.g.  and 

6

Sim. main value

A0026099-EN

 4 Display (e.g. simulation mode)

6.1.2 Key functions



ENTER key

• Switches on the device (press for at least 3 seconds)

• Calls up menu when in simulation mode

• Saves (confirms) data entered

• Selects a menu option

• Switches off the device (press for at least 3 seconds)

 or  MINUS key or PLUS key

In setup mode, the MINUS and PLUS keys have the following
functions:

• Configuration of parameters and numerical values

• Navigation through menu
In simulation mode, the MINUS and PLUS keys have the following

functions:
"Run through" of sim. main values, with each values being changed by
the amount of the delta value

 and  Escape function

Press MINUS and PLUS key simultaneously

• Pressing for a short time: takes you up one level in the menu.

• Pressing for a longer time in the main menu: takes you directly to
the simulation mode.

14 Endress+Hauser

Memocheck Sim CYP03D Operation options

 and  Reset

Press MINUS and ENTER key simultaneously for longer
Saved setups remain intact.

 and  Factory settings

Press PLUS and ENTER key simultaneously for longer

• This resets the device to the factory settings.

• All the setups saved are deleted.

Endress+Hauser 15

Operation options Memocheck Sim CYP03D

pH glass

pH Isfet

ORP
Cond c

Oxygen (amp.)

Chlorine

pH glass SIL

Cond i
Oxy. (opt.fixed)
Turbidity
Nitrate
SAC

Language
Display

Setup

Illumination
Contrast

Simulation

Parameter

Memosens

Fixed cable

Sim. main value

Test values
Save setup
Load setup
Advanced

Date

Time

Switch off auto.

Advanc. function

Calibration value
Error simulation
Ramp (continuous)

Diagnostics

Diagnostic list
Order code
Serial number
Software
Hardware
Reset
Factory settings

Switch off

pH + ORP

Cond c 4-pol

Oxygen (opt.Memo.)

Ramp (gradual)

6.2 Structure and function of the operating menu

6.2.1 Menu structure

16 Endress+Hauser

Memocheck Sim CYP03D Operation options

-

-

-

6.2.2 Operating concept

Example of changing values within a menu: defining the start value of a ramp

Maximum and minimum values are displayed in the editor. You can only configure values
within these limits.

1. Use the arrow keys to select the digit of the value that you want to change.

2. Press  to change the value.
 The digit flashes

3. Press  or  to increase or decrease the value.

4. Confirm entry with .
 The "Escape" function ( and  pressed simultaneously) is disabled here in order

to prevent incorrect entries.

5. Select the check mark (arrow key) and press .
 The edited value is accepted.

Endress+Hauser 17

Commissioning Memocheck Sim CYP03D

7 Commissioning

7.1 Switching on the measuring device

Switch on the device

Press and hold  for at least 3 seconds.

‣

 This loads the last setup that was saved.

Switch off the device

Press and hold  for at least 3 seconds.

‣

7.2 Setting the operating language

Configure language

Available languages (factory settings in bold)

• Deutsch

• English

• Français

• Español

• Italiano

1. Press key for Menu .

2. Language Select (using ).

3. Select language, e.g.English.

4. Confirm selection, answer the prompt that follows with .
 From now on, you will be guided through the menu in the language of your choice.

Pressing and takes you back to the main menu.

7.3 Quick Setup

Selecting a parameter and configuring test values

1. Under Setup/Simulation select the desired parameter, e. g.ORP (available parameters
→  10).

 Confirm entry with .

2. Under Setup/Simulation/Test values , enter the test values (→  21).

3. Press  and  simultaneously.
 You are in the simulation mode.

18 Endress+Hauser

Memocheck Sim CYP03D Commissioning

You can now simulate the selected parameter using the selected settings.

Once you connect the Memocheck Sim CYP03D to a Memosens transmitter, the
Memosens icon appears in the status line of the simulator. It indicates that the
simulator is communicating with the transmitter. The simulation symbol shown on the
transmitter display indicates that the transmitter is in simulation mode (→ Operating
Instructions of the transmitter).

Endress+Hauser 19

Operation Memocheck Sim CYP03D

8 Operation

8.1 Configuring the measuring device

8.1.1 Display behavior Possible settings

• Illumination

• Contrast

Path: Menu/Display

Change the illumination or contrast setting for the display using  or .

‣

 Confirm entry with  .

8.1.2 General settings

Path: Menu/Setup/Advanced

Function Configuration options

(factory settings in bold)

Date

Year 09 to 99

10

Month 01 to 12

03

Day 01 to 31

28

Time

Hour 00 to 23

06

Minute 00 to 59

30

Second 00 to 59

21

Switch off auto. 5 to 100 min

20 min

Info

Set current date.

‣

Set current time.

‣

Configure automatic switch-off.

‣

 If the simulator is connected to a

transmitter, this function is deactivated.
In this case, the simulator does not switch
off automatically.

20 Endress+Hauser

Memocheck Sim CYP03D Operation

8.1.3 Selecting parameters

In the setup, you configure which parameters are to be simulated.

1. Path: Menu/Setup/Simulation/Parameter.
 The parameters currently configured are displayed.

2. Select new parameter: Parameter/Memosens or Fixed cable. Select the desired
parameter.

 If the parameter is changed, the following prompt appears:

ESC = cancel
 = direct parameter change, the last settings for the current parameter are lost
 = save setup, followed by a prompt to specify where to save the setup. Select a
free location so that setups already saved are not overwritten.

3. Select desired option.

Under Menu/Setup/Save setup , you can save up to 10 setups under the relevant
parameter name. If you want to use a saved setup, select it under the "Setup/Load setup"
menu.

8.1.4 Configuring sim. main value and test values

A setup comprises the selected parameter, a simulation main value and test values.
You can change the simulation main value in the simulation mode using a user-definable

delta value. The delta value is the increment by which you change the simulation value by
pressing  and .

Test values are all other measured values (including raw measured values) of a test setup. Test
values are set to a fixed value, which cannot be modified in the simulation mode.

1. Menu/Setup/Simulation/Parameter/Memosens or .../Fixed cable: Select the
parameter, e. g. pH glass.

2. Menu/Setup/Simulation/Sim. main value: Select the measured value to be simulated,
e. g. pH value.

 A prompt asking if you wish to change the delta value () or not ().

3. Select .
 The current delta value is now displayed, e. g. 00.10 pH.

4. Change the current value, e. g. to 00.50 pH.

5. Accept value (use  to select the  beside the value and then ).

Endress+Hauser 21

Operation Memocheck Sim CYP03D

6. Menu/Setup/Simulation/Test values: set other measured values, which are shown on
the display ( Temperatureonly) or on the transmitter as a fixed value.

7. Change the value to the desired display, e. g. 25.00 °C.
 The test value remains at the value set here and cannot be modified in the

simulation mode.

8. Pressing  and  for longer takes you directly to the simulation mode.

The Sim. main value is displayed as the first value in the simulation mode. You can press 
or  to change the set delta value. The temperature is displayed as the second value. Pressing
 and  does not affect this value. The other test values, which are not visible on the
Memocheck display, can only be read off the transmitter or output to transmitter outputs.

Parameter Chlorine

To ensure that the simulator and transmitter display the identical chlorine
concentration, the pH value which is used for calculation purposes must be the same for
the transmitter and the simulator.

Parameter Oxygen (amp.) or Oxygen (opt.Memo.)

To ensure that the simulator and transmitter display the identical oxygen concentration,
the following values used for calculation purposes must be the same for the transmitter
and the simulator: Salinity and Process pressure/Altitude.

22 Endress+Hauser

Memocheck Sim CYP03D Operation

Sim main values Memosens (factory settings in bold)

pH glass pH glass SIL pH Isfet pH + ORP

• pH value

• Temperature

• Raw value

• Raw value temp.

• SCS resistance

ORP Cond c Cond c 4-pol Oxygen (amp.)

• ORP potential

• ORP [%]

• Temperature

• Raw value

• Raw value temp.

Oxygen (opt.Memo.) Chlorine

• Partial pressure

• Saturation

• Conc. liquid

• Conc. gas.

• Temperature

• Salinity

• Process pressure

• Altitude

• Raw value temp.

• pH value

• Temperature

• Raw value

• Raw value temp.

• SCS resistance

• Conductivity

• Temperature

• Resistance

• Raw value temp.

• Phase

• Chlor. concentr.

• Current

• Temperature

• pH value

• Raw value current

• Raw value temp.

• pH value

• Temperature

• Raw value

• Raw value temp.

• Conductivity

• Temperature

• Resistance

• Raw value temp.

• pH value

• ORP potential

• rH value

• Temperature

• Conc. liquid

• Current

• Saturation

• Partial pressure

• Conc. gas.

• Temperature

• Salinity

• Process pressure

• Altitude

• Raw value current

• Raw value temp.

Sim main values Fixed cable (factory settings in bold)

Cond i Oxy. (opt.fixed) Turbidity Nitrate SAC

• Conductivity

• Temperature

• Resistance

• Raw value temp.

• Partial pressure

• Saturation

• Conc. liquid

• Temperature

• Salinity

• Raw value temp.

• Slope

• Temperature

• TU value [FNU]

• TU value [g/l]

• Raw value temp.

• Content NO3

• Content NO3-N

• Temperature

• Raw value temp.

• TOC

• CSB

• Temperature

• SAC value

• Raw value temp.

8.2 Extended functions

In the Advanc. function menu, you can enter the following values. These values always refer
to the last parameters selected under Simulation .

• Calibration value

• Error simulation

• Ramp (continuous)

• Ramp (gradual)

Endress+Hauser 23

Operation Memocheck Sim CYP03D

t

Value

Max.

Min.

Value

Max.

Min.

t

8.2.1 Calibration value

The calibration value of the simulated sensor is the value to which the sensor adjustment
refers.

If you change a calibration value, there will be a brief interruption to communication between
the Memocheck Sim CYP03D and the transmitter to allow the transmitter to accept the
calibration settings.

An unfavorable configuration may result in measured values outside the specified
measuring range. This can lead to fault states in the transmitter. More information on
calibration can be found in the Operating Instructions for your transmitter.

8.2.2 Error simulation

You receive a list of possible errors which you can combine with one another.
The error categories in accordance with NAMUR (F, M, C, S) are treated as follows:

• The errors declared as "F" in the transmitter are indicated by a flashing display.

• Errors in other categories are displayed in the transmitter's diagnostic list.

8.2.3 Ramps Ramp (continuous): You define the start and stop value as well as the duration of a ramp

(Starting value, Stop value, Duration).
Ramp (gradual): Instead of a total time, you define the number and the duration of the

increments (Number of steps, Time per step).

Ramp (continuous)

The ramp rises continuously without any

Ramp (gradual)

The ramp is gradual.

jumps.

A0017397-EN

• The ramp repeats itself automatically until you stop it.

• The ramp is a simple linear function y = mx + n. The linear element "n" is normally equal to
the zero point. The factor "m" is the slope of the line.

• You will obtain a negative slope for the ramp if you set the starting value higher than the
stop value.

24 Endress+Hauser

A0017398-EN

Memocheck Sim CYP03D Operation

x

y

n

y1

y2

x1

x2

m=

y2-y1
x2-x1

x

y

n

y2

y1

x1

x2

m=

y2-y1
x2-x1

 5 Linear function

n Zero point
m Slope
y1 Start Value
y2 Stop value
x Time

x2-x1 = duration

A0017356

 6 Negative slope

n Zero point
m Slope
y1 Start Value
y2 Stop value
x Time

x2-x1 = duration

A0017359

8.2.4 Extended functions: pH glass and pH glass SIL

Path: Menu/Advanc. function

Function Configuration options

Calibration value

Temp. offset -10.0 to 10.0 ˚C

pH comp. isoth. 0.0 to 12.0 pH

mV comp. isoth. -300.0 to 300.0 mV

Slope 0.01 to 65.0 mV/pH

Zero point 0.0 to 12.0 pH

(factory settings in bold)

0.0 ˚C

7.0 pH

0.0 mV

59.16 mV/pH

7.0 pH

Endress+Hauser 25

Operation Memocheck Sim CYP03D

Path: Menu/Advanc. function

Function Configuration options

Error simulation Glass SCS failure

Ramp Ramp

Sim. main value Starting

pH value -2.0 to 16.0

Temperature -40.0 to

Raw value -750.0 to

Raw value temp. -40.0 to

SCS resistance 0.001 MΩ to

(factory settings in bold)

Temp. sens. defect
Glass SCS warning

value

pH

-2.0 pH

150.0 ˚C

-40.0 °C

750.0 mV

-750.0 mV

150.0 ˚C

-40.0 °C

1.0 TΩ

0.001 MΩ

Stop value Duration Number of

-2.0 to 16.0
pH

16.0 pH

-40.0 to

150.0 ˚C

150.0 °C

-750.0 to

750.0 mV

750.0 mV

-40.0 to

150.0 ˚C

150.0 °C

0.001 MΩ to

1.0 TΩ

1.0 TΩ

Once you have selected an error using ,



the error is output at the transmitter. To
delete the error again, remove the check
mark again using .

(continuous)

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

Ramp (gradual)

steps

1 to 200

10

1 to 200

10

1 to 200

10

1 to 200

10

1 to 200

10

Time per step

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

8.2.5 Extended functions: pH Isfet

Path: Menu/Advanc. function

Function Configuration options

Calibration value

Temp. offset -10.0 to 10.0 ˚C

Slope 0.01 to 65.0 mV/pH

pH comp. isoth. 0.0 to 12.0 pH

mV comp. isoth. -300.0 to 300.0 mV

Asymmetry -300.0 to 300.0 mV

26 Endress+Hauser

(factory settings in bold)

0.0 ˚C

59.16 mV/pH

7.0 pH

0.0 mV

0.0 mV

Memocheck Sim CYP03D Operation

Path: Menu/Advanc. function

Function Configuration options

Error simulation Leak. curr. alarm

Ramp Ramp

Sim. main value Starting

pH value -2.0 to 16.0

Temperature -40.0 to

Raw value -750.0 to

Raw value temp. -40.0 to

(factory settings in bold)

Leak. curr. warn
Temp. sens. defect
Sensor supply

value

pH

-2.0 pH

150.0 ˚C

-40.0 °C

750.0 mV

-750.0 mV

150.0 ˚C

-40.0 °C

Stop value Duration Number of

-2.0 to 16.0
pH

16.0 pH

-40.0 to

150.0 ˚C

150.0 °C

-750.0 to

750.0 mV

750.0 mV

-40.0 to

150.0 ˚C

150.0 °C

Once you have selected an error using ,



the error is output at the transmitter. To
delete the error again, remove the check
mark again using .

(continuous)

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

Ramp (gradual)

steps

1 to 200

10

1 to 200

10

1 to 200

10

1 to 200

10

Time per step

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

Endress+Hauser 27

Operation Memocheck Sim CYP03D

8.2.6 Extended functions: pH + ORP

Path: Menu/Advanc. function

Function Configuration options

Calibration value

pH value -200.0 mV

pH comp. isoth. 0.0 to 12.0 pH

mV comp. isoth. -300.0 to 300.0 mV

Slope 0.01 to 65.0 mV/pH

Zero point 0.0 to 12.0 pH

ORP potential

Cal. point 1 [mV] -2.0 to 2.0 V

Cal. point 2 [mV] -2.0 to 2.0 V

Cal. point 1 [%] 0.0 to 100.0 %

Cal. point 2 [%] 0.0 to 100.0 %

ORP % slope -30.0 to 30.0 mV/%

ORP % zero point -1.0 to 1.0 V

rH value 0.0 to 100.0 %

rH offset -300.0 to 300.0 rH

Temperature 0.0 to 100.0 %

Temp. offset -10.0 to 10.0 ˚C

(factory settings in bold)

7.0 pH

0.0 mV

56.12 mV/pH

7.0 pH

-200.0 mV

200.0 mV

10.0 %

30.0 %

20.0 mV/%

-400.0 mV

10.0 %

0.0 rH

30.0 %

0.0 ˚C

28 Endress+Hauser

Memocheck Sim CYP03D Operation

Path: Menu/Advanc. function

Function Configuration options

Error simulation Glass SCS failure

Ramp Ramp

Sim. main value Starting

pH value

pH value -2.0 to 16.0

Raw v. C1-C2 (pH) -750.0 to

SCS resistance 0.001 MΩ to

Refer. SCS resist. 0.01 to

ORP potential

ORP potential -2.0 to 2.0 V

ORP [%] 0.0 to

Raw val. -C2 (ORP) -2.0 to 2.0 V

Raw value C1 -3.0 to 3.0 V

rH value

rH value -40.0 to

(factory settings in bold)

Ref. SCS failure
Temp. sens. defect
Glass SCS warning
Ref. SCS warning
Counter spillover
Meas. value inval.

value

pH

-2.00 pH

750.0 mV

-750.0 mV

1.000 TΩ

0.001 MΩ

60.0 kΩ

0.01 kΩ

-2.0 V

100.0 %

0.0 %

-2.0 V

-3.0 V

50.0 rH

-40.0 rH

Stop value Duration Number of

-2.0 to 16.0
pH

16.0 pH

-750.0 to

750.0 mV

750.0 mV

0.001 MΩ to

1.000 TΩ

1.000 TΩ

-2.0 to 16.0
pH

16.0 pH

-2.0 to 2.0 V

2.0 V

0.0 to

100.0 %

100.0 %

-2.0 to 2.0 V

2.0 V

-3.0 to 3.0 V

3.0 V

-40.0 to

50.0 rH

50.0 rH

Once you have selected an error using



, the error is output at the
transmitter. To delete the error again,
remove the check mark again using .

(continuous)

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

Ramp (gradual)

steps

1 to 200

10

1 to 200

10

1 to 200

10

1 to 200

10

1 to 200

10

1 to 200

10

1 to 200

10

1 to 200

10

1 to 200

10

Time per
step

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

Endress+Hauser 29

Operation Memocheck Sim CYP03D

Path: Menu/Advanc. function

Function Configuration options

Temperature

Temperature -40.0 to

Raw value temp. -40.0 to

(factory settings in bold)

150.0 ˚C

-40.0 °C

150.0 ˚C

-40.0 °C

-40.0 to

150.0 ˚C

150.0 °C

-40.0 to

150.0 ˚C

150.0 °C

10 to 6000 s

60 s

10 to 6000 s

60 s

1 to 200

10

1 to 200

10

0.5 to 600 s

1 s

0.5 to 600 s

1 s

8.2.7 Extended functions: ORP

Path: Menu/Advanc. function

Function Configuration options

Calibration value

Cal. point 1 [mV] -2.0 to 2.0 V

Cal. point 2 [mV] -2.0 to 2.0 V

Cal. point 1 [%] 0.0 to 100.0 %

Cal. point 2 [%] 0.0 to 100.0 %

ORP mV offset -1.0 to 1.0 V

Temp. offset -10.0 to 10.0 ˚C

ORP % slope -30.0 to 30.0 mV/%

ORP % zero point -1.0 to 1.0 V

(factory settings in bold)

-200.0 mV

200.0 mV

10.0 %

30.0 %

0.0 mV

0.0 °C

16.47 mV/%

-833.3 mV

30 Endress+Hauser

Memocheck Sim CYP03D Operation

Path: Menu/Advanc. function

Function Configuration options

Error simulation Temp. sens. defect

Ramp Ramp

Sim. main value Starting

ORP potential -2.0 to 2.0 V

ORP [%] 0.0 to

Temperature -40.0 to

Raw value -2.0 to 2.0 V

Raw value temp. -40.0 to

(factory settings in bold)

Sensor supply

value

-2.0 V

100.0 %

0.0 %

150.0 ˚C

-40.0 °C

-2.0 V

150.0 ˚C

-40.0 °C

Stop value Duration Number of

-2.0 to 2.0 V

2.0 V

0.0 to

100.0 %

100.0 %

-40.0 to

150.0 ˚C

150.0 °C

-2.0 to 2.0 V

2.0 V

-40.0 to

150.0 ˚C

150.0 °C

Once you have selected an error using ,



the error is output at the transmitter. To
delete the error again, remove the check
mark again using .

(continuous)

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

Ramp (gradual)

steps

1 to 200

10

1 to 200

10

1 to 200

10

1 to 200

10

1 to 200

10

Time per step

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

8.2.8 Extended functions: Cond c, Cond c 4-pol and Cond i

Path: Menu/Advanc. function

Function Configuration options

Calibration value Conductive Toroidal

Cell constant 0.001 E-03 to

Reference value 0.001 mS/cm

Reference temp. 0.0 to 60.0 ˚C

Temp. offset -10.0 to 10.0 ˚C

Temp. gradient -3.0 to 3.0

Endress+Hauser 31

(factory settings in bold)

0.001 E-03 to

-1

10.0 cm

10 E-03 cm

to 1.0 S/cm

0.005 mS/cm

25.58 °C

0.0 ˚C

1.0

10.0 cm

-1

2.9 cm

0.001 mS/cm
to 1.0 S/cm

100.0 mS/cm

0.0 to 60.0 ˚C

25.0 °C

-1

-1

Operation Memocheck Sim CYP03D

Path: Menu/Advanc. function

Function Configuration options

Error simulation Cond c

Ramp Ramp

Sim. main value Starting

Conductivity 0.001 µS/cm

Temperature -40.0 to

Resistance 0.001 mΩ to

Raw value temp. -40.0 to

(factory settings in bold)

• Polarizat. warn.

• No Cond. display

• Temp. sens. defect

• Sensor supply

Cond c 4-pol

• Polarizat. warn.

• Cond. val. invalid

• Temp. sens. defect

• Broken connector

• Meas. value inval.

• Resist. maximum

Cond i

• Cond. sens. defect

• Cond. val. invalid

• Temp. sens. defect

• Temp. value inval.

• Ind. curr. too high

• Ind. curr. too low

value

to 2000 S/cm

0.001 µS/cm

150.0 ˚C

-40.0 °C

1.0 GΩ

0.001 mΩ

150.0 ˚C

-40.0 °C

Stop value Duration Number of

0.001 µS/cm
to 2000 S/cm

2000 S/cm

-40.0 to

150.0 ˚C

150.0 °C

0.001 mΩ to

1.0 GΩ

1.0 GΩ

-40.0 to

150.0 ˚C

150.0 °C

Once you have selected an error using ,



the error is output at the transmitter. To
delete the error again, remove the check
mark again using .

(continuous)

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

Ramp (gradual)

steps

1 to 200

10

1 to 200

10

1 to 200

10

1 to 200

10

Time per step

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

32 Endress+Hauser

Memocheck Sim CYP03D Operation

8.2.9 Extended functions: Oxygen (amp.)

Path: Menu/Advanc. function

Function Configuration options

Calibration value

Slope 0.1 pA/hPa to 5.0 nA/hPa

Zero point -3.2 nA to 3.2 nA

Temp. offset -10.0 to 10.0 ˚C

Temp. gradient -3.0 to 3.0

Temp. coeff. 1 20.00 E-03 to 40.00 E-03

Temp. coeff. 2 100.0 E-06 to 500.0 E-06

Temp. coeff. 3 500.0 E-09 to 5.000 E-06

Temp. coeff. 4 1.000 E-09 to 70.00 E-09

(factory settings in bold)

313.5 pA/hPa

0.0 pA

0.0 ˚C

1.0

30.79 E-03

447.6 E-06

4.224 E-06

66.75 E-09

Endress+Hauser 33

Operation Memocheck Sim CYP03D

Path: Menu/Advanc. function

Function Configuration options

Error simulation Leak. curr. alarm

Ramp Ramp

Sim. main value Starting

Conc. liquid -0.02 to

Current 0.0 pA to

Saturation -0.02 to

Partial pressure 0.0 to 440.0

Conc. gas. 0.0 to

Temperature -40.0 to 60.0

Salinity 0.0 to 40.0

Process pressure 500 to 9999

Altitude -300 to 4000

Raw value current 0.0 pA to

Raw value temp. -40.0 to 60.0

(factory settings in bold)

Leak. curr. warn
Temp. sens. defect
Sensor supply

value

120.0 mg/l

-0.02 mg/l

640.0 nA

0.0 nA

1000 % sat

-0.02 % sat

hPa

0.0 hPa

100.0 %

0.0 %

˚C

-40.0 °C

g/kg

0.0 g/kg

hPa

500 hPa

m

-300 m

640.0 nA

0.0 pA

˚C

-40.0 °C

Stop value Duration Number of

-0.02 to

120.0 mg/l

120.0 mg/l

0.0 pA to

640.0 nA

640.0 nA

-0.02 to
1000 % sat

1000 % sat

0.0 to 440.0
hPa

440.0 hPa

0.0 to

100.0 %

100.0 %

-40.0 to 60.0
˚C

60.0 °C

0.0 to 40.0
g/kg

40.0 g/kg

500 to 9999
hPa

9999 hPa

-300 to 4000
m

4000 m

0.0 pA to

640.0 nA

640.0 nA

-40.0 to 60.0
˚C

60.0 °C

Once you have selected an error using ,



the error is output at the transmitter. To
delete the error again, remove the check
mark again using .

(continuous)

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

Ramp (gradual)

steps

1 to 200

10

1 to 200

10

1 to 200

10

1 to 200

10

1 to 200

10

1 to 200

10

1 to 200

10

1 to 200

10

1 to 200

10

1 to 200

10

1 to 200

10

Time per step

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

34 Endress+Hauser

Memocheck Sim CYP03D Operation

8.2.10 Extended functions: Oxygen (opt.Memo.)

Path: Menu/Advanc. function

Function Configuration options

Calibration value

Temp. offset -10.0 to 10.0 ˚C

Temp. gradient -3.0 to 3.0

Cal. Quality 0.0 to 100.0 %

(factory settings in bold)

0.0 ˚C

1.0

100.0 %

Endress+Hauser 35

Operation Memocheck Sim CYP03D

Path: Menu/Advanc. function

Function Configuration options

Error simulation Measurement stop

Ramp Ramp

Sim. main value Starting

Partial pressure 0.0 to 440.0

Saturation -0.02 to

Conc. liquid -0.02 to

Conc. gas. 0.0 to

Temperature -40.0 to 60.0

Salinity 0.0 to 40.0

Process pressure 500 to 9999

Altitude -300 to 4000

Raw value temp. -40.0 to 60.0

(factory settings in bold)

No ref. cal. P1
No ref. cal. P2
No amplitude
Tau too low
Tau too high
Wave form
Temp. sens. defect
Temp. out of spec.
Electronics temp.
Electronic-error

value

hPa

0.0 hPa

1000 % sat

-0.02 % sat

120.0 mg/l

-0.02 mg/l

100.0 %

0.0 %

˚C

-40.0 °C

g/kg

0.0 g/kg

hPa

500 hPa

m

-300 m

˚C

-40.0 °C

Stop value Duration Number of

0.0 to 440.0
hPa

440.0 hPa

-0.02 to
1000 % sat

1000 % sat

-0.02 to

120.0 mg/l

120.0 mg/l

0.0 to

100.0 %

100.0 %

-40.0 to 60.0
˚C

60.0 °C

0.0 to 40.0
g/kg

40.0 g/kg

500 to 9999
hPa

9999 hPa

-300 to 4000
m

4000 m

-40.0 to 60.0
˚C

60.0 °C

Once you have selected an error using ,



the error is output at the transmitter. To
delete the error again, remove the check
mark again using .

(continuous)

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

Ramp (gradual)

steps

1 to 200

10

1 to 200

10

1 to 200

10

1 to 200

10

1 to 200

10

1 to 200

10

1 to 200

10

1 to 200

10

1 to 200

10

Time per step

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

36 Endress+Hauser

Memocheck Sim CYP03D Operation

8.2.11 Extended functions: Oxy. (opt.fixed)

Path: Menu/Advanc. function

Function Configuration options

Calibration value

Slope 0 ... 200 %

Tau -5.0 to 105.0 µs

Temp. offset -10.0 to 10.0 ˚C

Temp. gradient -3.0 to 3.0

(factory settings in bold)

100%

20.0 µs

0.0 ˚C

1.0

Endress+Hauser 37

Operation Memocheck Sim CYP03D

Path: Menu/Advanc. function

Function Configuration options

Error simulation Tau too low

Ramp Ramp

Sim. main value Starting

Partial pressure 0.0 to 440.0

Saturation -0.02 to

Conc. liquid -0.02 to

Temperature -40.0 to 60.0

Salinity 0.0 to 40.0

Raw value temp. -40.0 to 60.0

Slope 0.0 to

(factory settings in bold)

Tau too high
No signal dropout
No amplitude
Temp. too low
Temp. too high
LED voltage
No LED current
Dynamic error

value

hPa

0.0 hPa

1000 % sat

-0.02 % sat

120.0 mg/l

-0.02 mg/l

˚C

-40.0 °C

g/kg

0.0 g/kg

˚C

-40.0 °C

200.0 %

0.0 %

Stop value Duration Number of

0.0 to 440.0
hPa

440.0 hPa

-0.02 to
1000 % sat

1000 % sat

-0.02 to

120.0 mg/l

120.0 mg/l

-40.0 to 60.0
˚C

60.0 °C

0.0 to 40.0
g/kg

40.0 g/kg

-40.0 to 60.0
˚C

60.0 °C

0.0 to

200.0 %

200.0 %

Once you have selected an error using ,



the error is output at the transmitter. To
delete the error again, remove the check
mark again using .

(continuous)

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

Ramp (gradual)

steps

1 to 200

10

1 to 200

10

1 to 200

10

1 to 200

10

1 to 200

10

1 to 200

10

1 to 200

10

Time per step

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

38 Endress+Hauser

Memocheck Sim CYP03D Operation

8.2.12 Extended functions: Chlorine

Path: Menu/Advanc. function

Function Configuration options

Calibration value

Slope -500.0 to -0.01 nA/g/l

Zero point -100.0 nA to 100.0 nA

Temp. offset -10.0 to 10.0 ˚C

Temp. gradient -3.0 to 3.0

Error simulation Temp. sens. defect

Ramp Ramp

Sim. main value Starting

Chlor. concentr. 0.0 to 200.0

Current -1.5 µA to 0.0

Temperature -40.0 to 60.0

pH value -2.0 to 16.0

Raw value current -1.5 µA to 0.0

Raw value temp. -40.0 to 60.0

(factory settings in bold)

-25.0 nA/g/l

0.0 pA

0.0 ˚C

1.0

Sensor supply

value

mg/l

0.0 mg/l

pA

-1.5 µA

˚C

-40.0 °C

pH

-2.0 pH

pA

-1.5 µA

˚C

-40.0 °C

Stop value Duration Number of

-0.02 to

120.0 mg/l

120.0 mg/l

-1.5 µA to 0.0
pA

0.0 pA

-40.0 to 60.0
˚C

60.0 °C

-2.0 to 16.0
pH

16.0 pH

-1.5 µA to 0.0
pA

0.0 pA

-40.0 to 60.0
˚C

60.0 °C

Once you have selected an error using ,



the error is output at the transmitter. To
delete the error again, remove the check
mark again using .

(continuous)

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

Ramp (gradual)

steps

1 to 200

10

1 to 200

10

1 to 200

10

1 to 200

10

1 to 200

10

1 to 200

10

Time per step

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

Endress+Hauser 39

Operation Memocheck Sim CYP03D

8.2.13 Extended functions: Turbidity

Path: Menu/Advanc. function

Function Configuration options

Calibration value

Temp. offset -10.0 to 10.0 ˚C

Error simulation LED error

Ramp Ramp

Sim. main value Starting

Temperature -40.0 to

TU value [FNU] 0.0 to

TU value [g/l] 0.001 to 1000

Raw value temp. -40.0 to

(factory settings in bold)

0.0 ˚C

Turbidit. too high
Electronics test
Sensor polluted
Meas. val. uncert.
No cal. data
Temperature err.
Meas. value inval.
Measurement stop

value

150.0 ˚C

-40.0 °C

10000.0 FNU

0.0 FNU

g/l

0.001 g/l

150.0 ˚C

-40.0 °C

Stop value Duration Number of

-40.0 to

150.0 ˚C

150.0 °C

0.0 to

10000.0 FNU

10000.0 FNU

0.001 to 1000
g/l

1000 g/l

-40.0 to

150.0 ˚C

150.0 °C

Once you have selected an error using ,



the error is output at the transmitter. To
delete the error again, remove the check
mark again using .

(continuous)

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

Ramp (gradual)

steps

1 to 200

10

1 to 200

10

1 to 200

10

1 to 200

10

Time per step

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

40 Endress+Hauser

Memocheck Sim CYP03D Operation

8.2.14 Extended functions: Nitrate

Path: Menu/Advanc. function

Function Configuration options

Calibration value

Temp. offset -10.0 to 10.0 ˚C

Error simulation Flash lamp defect

Ramp Ramp

Sim. main value Starting

Content NO3 0.001 mg/l to

Content NO3-N 0.0 µg/l to

Temperature -40.0 to

Raw value temp. -40.0 to

(factory settings in bold)

0.0 ˚C

Turbidit. too high
Electronics test
Filter change
Meas. val. uncert.
No cal. data
Temperature err.
Measurement stop
Meas. value inval.

value

550 mg/l

0.001 mg/l

500.0 mg/l

0.0 µg/l

150.0 ˚C

-40.0 °C

150.0 ˚C

-40.0 °C

Stop value Duration Number of

0.001 mg/l to
550 mg/l

550 mg/l

0.0 µg/l to

500.0 mg/l

500.0 mg/l

-40.0 to

150.0 ˚C

150.0 °C

-40.0 to

150.0 ˚C

150.0 °C

Once you have selected an error using ,



the error is output at the transmitter. To
delete the error again, remove the check
mark again using .

(continuous)

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

Ramp (gradual)

steps

1 to 200

10

1 to 200

10

1 to 200

10

1 to 200

10

Time per step

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

Endress+Hauser 41

Operation Memocheck Sim CYP03D

8.2.15 Extended functions: SAC

Path: Menu/Advanc. function

Function Configuration options

Calibration value

Temp. offset -10.0 to 10.0 ˚C

Error simulation Flash lamp defect

Ramp Ramp

Sim. main value Starting

TOC 0.000 mg/l to

CSB 0.000 mg/l to

Temperature -40.0 to

SAC value 0.0 to

Raw value temp. -40.0 to

(factory settings in bold)

0.0 ˚C

Turbidit. too high
Electronics test
Filter change
Meas. val. uncert.
No cal. data
Temperature err.
Measurement stop

value

100.0 g/l

0.000 mg/l

100.0 g/l

0.000 mg/l

150.0 ˚C

-40.0 °C

100.0 E03

-1

m

-1

0.0 m

150.0 ˚C

-40.0 °C

Stop value Duration Number of

0.000 mg/l to

100.0 g/l

100.0 g/l

0.000 mg/l to

100.0 g/l

100.0 g/l

-40.0 to

150.0 ˚C

150.0 °C

0.0 to

100.0 E03

-1

m

100.0 E03

-1

m

-40.0 to

150.0 ˚C

150.0 °C

Once you have selected an error using ,



the error is output at the transmitter. To
delete the error again, remove the check
mark again using .

(continuous)

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

10 to 6000 s

60 s

Ramp (gradual)

steps

1 to 200

10

1 to 200

10

1 to 200

10

1 to 200

10

1 to 200

10

Time per step

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

0.5 to 600 s

1 s

42 Endress+Hauser

Memocheck Sim CYP03D Diagnosis

9 Diagnosis

Path: Menu/Diagnostics

Function Info

Diagnostic list The diagnostic messages provide information to

Order code CYP03D-xxx

Serial number xxxxxxxxxxx

Software x.xx.xx

Hardware x.xx.xx

Reset Device is restarted. Your stored settings will be

Factory settings All device settings are reset to the factory settings.

Endress+Hauser service personnel.

preserved.

All the setups saved are deleted.

10 Maintenance

10.1 Cleaning

Clean the device using only commercially available, mild, household cleaning agents.

‣

10.2 Battery replacement

The battery compartment is accessed from behind. Permitted battery types: →  6.

Only ever open the battery compartment in the non-hazardous area!

‣

10.3 Calibration and qualification

The Memocheck Sim CYP03D can, with the quality or calibration certificate, also be used as a
qualification tool for your measuring point.

The quality and calibration certificates can be renewed:
For such services, you will need to return Memocheck Sim CYP03D to Endress+Hauser.
In the case of requalification, the device is tested fully and a new quality certificate is issued.
In the case of recalibration, in addition to requalification the device is also incorporated into a
calibration procedure. A quality certificate and a certificate of calibration are issued. The
recommended testing interval is 1 year.

Endress+Hauser 43

Repair Memocheck Sim CYP03D

11 Repair

11.1 Spare parts

Battery compartment cover

Order No. 71138380

11.2 Return

The product must be returned if repairs or a factory calibration are required, or if the wrong
product was ordered or delivered. As an ISO-certified company and also due to legal
regulations, Endress+Hauser is obliged to follow certain procedures when handling any
returned products that have been in contact with medium.

To ensure the swift, safe and professional return of the device:

Refer to the website www.endress.com/support/return-material for information on the

‣

procedure and conditions for returning devices.

11.3 Disposal

The device contains electronic components. and must therefore be disposed of in accordance
with regulations on the disposal of electronic waste.

Observe the local regulations.

‣

Always dispose of batteries in accordance with local regulations on battery disposal.

44 Endress+Hauser

Memocheck Sim CYP03D Accessories

12 Accessories

The following are the most important accessories available at the time this documentation
was issued.

For accessories not listed here, please contact your Service or Sales Center.

‣

12.1 Memosens data cable

Order No. Memosens data cable CYK10 (optional)

71128718 CYK10-A032 + adapter, cable ends; Non-Ex

71128721 CYK10-G032 + adapter; only for CYP03D, Ex

To connect Memocheck Sim CYP03D to transmitters with M12 sockets and Pg couplings, you
require the Memosens data cable CYK10 supplied. The cable is always supplied with an
adapter piece so that it fits both M12 sockets and Pg couplings. If you wish to simulate fixed
cable sensors (turbidity, nitrate, toroidal conductivity, oxygen optical) with Memocheck Sim
CYP03D, you need this cable. When using sensors with an inductive Memosens plug-in head
(pH/ORP; oxygen, conductive conductivity, chlorine), the appropriate cable is already included
in the measuring point.

12.2 Storage case

Order No.

71183327 Ex

In the hazardous area, the Memocheck simulator case should only be opened to remove or put
back the Memocheck simulator. When opened, the case should never be exposed to process­related intensive electrostatic charges.

Endress+Hauser 45

Case for Memocheck Sim CYP03D

Technical data Memocheck Sim CYP03D

13 Technical data

13.1 Environment

13.1.1 Ambient temperature range

–20 to 50 °C (–4 to 120 °F)

13.1.2 Storage temperature

-20 to 55 °C (-4 to 130 °F)

13.1.3 Degree of protection

IP55

13.1.4 Electromagnetic compatibility

Interference emission and interference immunity as per EN 61326-1:2013, Class A for
Industry

46 Endress+Hauser

Memocheck Sim CYP03D Technical data

40.0 (1.57)

25.0 (0.98)

58.0 (2.28)

94.0 (3.7)

36.0 (1.42)

200.0 (7.87)

13.2 Mechanical construction

13.2.1 Dimensions

 7 Memocheck Sim CYP03D

All dimensions in mm (inch)

A0026005

13.2.2 Weight (incl. batteries)

0.3 kg (0.7 lbs)

13.2.3 Materials

Housing:

Endress+Hauser 47

ABS (UL 94 HB)

Technical data Memocheck Sim CYP03D

13.2.4 Batteries

For the Memocheck Sim CYP03D, use only the following battery types, as only these are
covered by the Ex approval:

• Energizer, EN91 (AA, 1.5 V, LR6 as per IEC), x 3

• Battery storage temperature: -20 to 35 ˚C (-4 to 95 ˚F)

48 Endress+Hauser

Memocheck Sim CYP03D Index

Index

Symbols

 mark ....................... 12

A

Accessories

Memosens data cable ............ 45

Storage case ..................45

Adapting the device ................ 20

Ambient temperature range ........... 46

B

Batteries .......................48

Battery replacement ................43

C

Calibration and qualification ........... 43

Calibration value .................. 24

Certificates and approvals .............12

Cleaning .......................43

Commissioning ...................18

Connection ..................... 13

D

Declaration of Conformity ............. 2

Degree of protection ................46

Designated use ....................5

Device description .................. 9

Diagnosis ...................... 43

Dimensions ..................... 47

Display ........................14

Display behavior .................. 20

Disposal ....................... 44

E

Electrical connection ................13

Electromagnetic compatibility .......... 46

Error simulation .................. 24

Ex approvals .................... 12

Extended functions ................ 23

Chlorine .................... 39

Conductivity ..................31

Nitrate .....................41

ORP ...................... 30

Oxy. (opt.fixed) ................37

Oxygen (amp.) ................ 33

Oxygen (opt.Memo.) .............35

pH + ORP ................... 28

pH glass .................... 25

pH glass SIL ..................25

pH Isfet .................... 26

SAC .......................42

Turbidity ....................40

I

Incoming acceptance ............... 11

K

Keys ......................... 14

M

Maintenance .................... 43

Manufacturer address ...............12

Materials ...................... 47

Measuring system .................. 9

Mechanical construction ............. 47

Menu structure ...................16

N

Nameplate ..................... 11

O

Occupational safety ................. 5

Operating concept ................. 17

Operating elements ................ 14

Operating language ................ 18

Operating menu .................. 16

Operation ...................... 20

Operation options ................. 14

Operational safety ..................6

Order code ......................11

P

Personnel .......................5

Product identification ............... 11

Product page .................... 11

Product safety .................... 6

Q

Quick Setup ..................... 18

Endress+Hauser 49

Index Memocheck Sim CYP03D

R

Ramp (continuous) .................24

Ramp (gradual) ...................24

Repair ........................ 44

Requirements for personnel ............ 5

Return ........................ 44

S

Safety instructions

Hazardous areas ................ 6

Operational safety ...............6

Requirements for personnel ......... 5

Scope of delivery .................. 12

Settings

Extended functions ........... 23, 25

General .................... 20

Operating language ............. 18

Quick Setup .................. 18

Selecting parameters ............ 21

Sim. main value and test values ...... 21

Simulation values ................. 10

Spare parts ..................... 44

State of the art .................... 6

Storage temperature ................46

Switching on .................... 18

Symbols ........................ 4

T

Technical data ................... 46

U

Use ...........................5

W

Warnings ....................... 4

Weight ........................47

50 Endress+Hauser

*71416644*

71416644

www.addresses.endress.com