Emerson SW605 Owner's Manual
Part No. F40BP74170000 Form No. BP7417
READ AND SAVE THESE INSTRUCTIONS
Ceiling Fan/Light
Remote Control & Wall Control
Owner's Manual
Remote Control
Model Number:
SR600
Remote Control
Model Number:
SR650
Wall Control with Switch Covers
Model Number:
SW605
For Use With RCK55, RC188 or RC212 Receivers
2
Safety Instructions
WARNING: To avoid fire, shock, and serious personal injury, follow all instructions
carefully.
1. Read your Owner's Manual carefully before installing the Remote Control or Wall
Control. Retain Owner's Manual for future reference.
2. Before servicing or cleaning the ceiling fan, switch power off at service panel and lock
service panel to prevent power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a warning device such as a
tag, to the service panel.
ADDITIONAL SAFETY INSTRUCTIONS FOR INSTALLATION
1. To avoid possible electrical shock, be sure electricity is turned off at the main fuse or
circuit breaker box before wiring.
2. Make certain no bare wires are exposed outside the wire connectors.
3. All wiring must conform to National and Local Electrical Codes.
4. Follow the recommended instructions for the proper method of wiring your new
Remote Control or Wall Control. If you feel you do not have enough electrical wiring
knowledge or experience, have your Remote Control or Wall Control installed by a
licensed electrician. Any electrical work not described in this manual should be
performed by a licensed electrician.
DATE CODE:
The date code of this fan may be found on the box, stamped in ink on a white label.
You should record this data above and keep it in a safe place for future use.
!
WARNING
General
Your Emerson Ceiling Fan/Light SR600
Remote Control consists of hand-held
transmitter and a receiver which is
mounted under the fan ceiling cover. The
remote control is designed to separately
control your ceiling fan speed and light
intensity.
The remote control transmitter is powered
by two AAA alkaline batteries (included).
To prevent possible damage if the
batteries should leak, be sure to remove
the batteries when the control is not to be
used for an extended period of time.
Code switches in the transmitter and
receiver may be set in 32 different
positions. If your fan and light go on and
off without using your control, you may be
getting interference from other remote
units such as garage door openers, car
alarms or security systems. To remedy this
situations, simply change the combination
code in your transmitter and receiver.
Preset Memory Feature
Your Emerson receiver is equipped with a
preset memory feature. If the AC supply to
the receiver is powered through a wall
switch, when the switch is turned OFF, the
control will remember the light intensity
and fan speed. When the switch is turned
back ON the light and fan will resume
operation as they were prior to the switch
being turned OFF.
3
General
Your Emerson Ceiling Fan/Light Control
may be used with a SR600 or SR650
Remote Control or a SW605 Wall Control.
The remote control or wall control is
designed to control your ceiling fan speed,
airflow direction, and light intensity.
Unpackaging
The carton with the SR650 Remote
Control contains a storage bracket with
two mounting screws.
The carton with the SW605 Wall Control
contains three switch covers; ivory, white
and almond color.
IMPORTANT
This Owner’s Manual is divided into three
sections. The first section: SR600
REMOTE CONTROL PROCEDURES,
describes how to install the two AAA
alkaline batteries in the SR600 remote
control transmitter and operating
fuctions. The second section: SR650
REMOTE CONTROL PROCEDURES
describes how to install the two CR2032
Lithium batteries in the SR650 remote
control transmitter and operating
fuctions. The third section describes how
to install the SW605 Wall Control. These
instructions must be performed prior to
installation of the ceiling fan as described
in the Ceiling Fan Owner’s Manual.
SR600 REMOTE
CONTROL PROCEDURES
4
Setting Operating
Frequency of SR600
Remote Control
1. Slide the five switch levers in the
remote control to your choice of ON
(up) or down positions. Use a ball-point
pen or small screwdriver and slide the
levers firmly up or down.
2. When power is restored, push and hold
the fan OFF button ( ) for 3 to 5
seconds to set the code in the receiver.
3. If airflow is desired in the opposite
direction, press the ( ) button on the
wall control. The fan must be operating
at any speed for the reverse button to
function. The blades will turn in the
opposite direction and reverse the
airflow.
4. To set the desired fan speed, press the
( ) button to decrease the speed and
the ( ) to increase the speed. The
LED display will light up to indicate the
new speed selected.
5. To turn the downlight on, press and
release the ( ) button. The light will
turn on at the light intensity previously
selected.
6. To turn the uplight on, press and
release the ( ) button. The light will
turn on at the light intensity previously
selected.
7. To vary the intensity of the light, hold
the DN or UP button down until the
desired light intensity is reached, then
release the button.
8. The sixth switch marked ON and I is for
dimming control of lights: Set switch to
ON to allow for dimming of the lights.
Set switch to I for no dimming of the
lights such as for fluorescent bulbs.
Figure 1
Your remote control has code switches
which must be set in one of 32 possible
code combinations. The five levers
(numbered 1, 2, 3, 4, and 5) on the
switches are factory-set in the ON (up)
position. Change the switch settings as
follows:
Figure 2
Installation of Storage
Bracket for SR600
Remote Control
A storage bracket is provided for holding
your remote control when not in use. If you
desire to use the bracket, install it on a
wall that is away from excess heat or
humidity (Figure 2).
Installation of Battery
1. Remove the battery cover by pressing
firmly below the arrow and sliding the
cover off the control (Figure 1).
2. Install two AAA alkaline batteries and
reinstall the battery cover.
REMOTE CONTROL
LEVERS
ON
1
234
I
5
TWO AAA
BATTERIES
CODE
SWITCHES
BATTERY
COMPARTMENT
COVER
SR600 REMOTE
CONTROL
TO INSTALL BRACKET TO WALL:
SLIDE THE COVER UP TO EXPOSE THE SCREW
HOLES FOR INSTALLATION
COVER
WALL
BRACKET
SCREW
HOLES (2)
Loading...