Emerson SiteI-O-Line, SiteI-O 10-0 User Manual

Specification for SiteI/O 10/0

DESCRIPTION: The SiteI/O 10/0 is part of the SiteI/O-Line, which allows a complete SiteScan
monitoring/control system to be built a piece at a time. It is a 32 bit microprocessor-based device
designed to monitor up to ten analog, digital, and/or dry contact type signals. Individual hardware
jumpers set signal-type selections. Screw terminal blocks are provided to terminate power,
communication, and input signal wiring.

DIMENSIONS: Module: 7.5” H x 11.3125” W x 2.75” D

19.05 cm H x 28.73 cm W x 7 cm D

Enclosure: 20" H x 18" W x 2.87" D
(Painted Steel) 508mm x 457.2mm x 72.89mm

See Enclosure Diagrams for mounting options.

POWER: 24VAC ± 10%, 50-60 Hz., 20 VA power consumption
(120/24VAC 40VA Transformer available)

INPUTS: Ten universal inputs, configurable for 0-5VDC, 0-20mA, or thermistor.

ENVIRONMENTAL
OPERATING RANGE: 0° to 130° F (-17.8° to 54.4° C), 10 to 90% relative humidity, non-condensing

COMMUNICATION: One (1) CMnet EIA-485 Port - Control Module network screw terminals

Switch selectable baud rates ARC156 / 9600 or 38.4bps

Recommended wire is: MAGNUM Cable pn A3-ARC-156-2

(10) Analog and/or Digital - screw terminals
Jumper Selectable inputs
Thermistor - 10k ohm @ 77° F, 25°C
0 to 5 VDC - 10k ohm max source impedance
4 to 20mA - 24VDC loop power, 250 ohm input
Dry Contact - 0.5mA sense current

MEMORY: 1 MB Flash Memory, 1 MB Non-volatile battery backed RAM.

PROTECTION: Voltage, current, and ESD protection on incoming power.

BATTERY: Seven-year lithium battery provides a minimum of 10,000 hours of data

retention during power outages.

Liebert Corporation Page 1 of 6 SL-28077 Rev.4; 7/03

Specification for SiteI/O 10/0

DIAGNOSTIC LED's:

Power: Indicates power on condition
Tx: Indicates data transmitted on the CMnet
Rx: Indicates data received on the CMnet
Error: Indicates an error within the SiteI/O 10/0
Run: Indicates operating condition of the SiteI/O 10/0

LISTED BY: UL 916 (PAZX), cUL C22.2 No. 205-M19 (PAZX7), FCC Part 15 – Subpart B –

Class A

MODULE DIMENSIONS AND LAYOUT

CMnet
Port

Keypad Display
Port

CMnet Mode
Jumper

13/16"
3cm

Run

OpenEnergy

88FO

E143900

TYPE: 008 102

R

Module

Address

10's 1's

Run and Power

Error

TM

LEDs

CAUTION:

ToR educe The Risk

ofFireorElectricShock,

DoNo tInterconnect

Output s of Di ffere nt Cla ss 2 C ircuit s

Power

On Off

24Vac, 50-60Hz

20VA,0.83A

Use Cop per

ConductorsOnly

Access

Port

Gnd

24Vac

Class2

Power

Access
Port

71/2"

19.05cm

33/4"

9.5cm

23/4"
7cm

Power Switch

11 5/16"

28.73cm

I/O

IN-1

B

IN-2

IN-3

A

IN-4

IN-5

B

IN-6

IN-7

A

IN-8

IN-9

B

IN-10

Expa nsion

Inputs
5VMax, 20mA
Max

UniversalInput

Mode Select

Thermistor/ 0-20
dry-contact

A-InputSignal

B - Gnd/Loop Pow er

Expa nsion

Net+

CMnet

Net-

Shield

Auxiliary

Device

Port

CMnet Mode

9600/

ARC156K

38.4K

1A

2

3A

4B

5A

6B

7

8B

9A

10

11 A

12 B

13 A

14 B

15

16 B

17 A

18

19 A

20 B

Baud Rate

Switch

0-5Vdc

mA

I/O

Rx Tx

SiteI/O 10/0

Liebert

ManagementEquipm ent

38.4k

CMnet baud

Format

9600

Format Button

Liebert Corporation Page 2 of 6 SL-28077 Rev.4; 7/03