Rack Mount LCD KVM Assembly
Installer/User Guide
Japanese Notification
Chinese Notification
Taiwanese Notification
Rack Mount LCD KVM Assembly
Installer/User Guide
Avocent, the Avocent logo and The Power of Being There are registered
trademarks of Avocent Corporation or its affliates in the U.S. and other
countries. All other marks are the property of their respective owners.
© 2010 Avocent Corporation. All rights reserved. 590-940-501C
Instructions
This symbol is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
Dangerous Voltage
This symbol is intended to alert the user to the presence of uninsulated
dangerous voltage within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
Power On
This symbol indicates the principal on/off switch is in the on position.
Power Off
This symbol indicates the principal on/off switch is in the off position.
Protective Grounding Terminal
This symbol indicates a terminal which must be connected to earth ground
prior to making any other connections to the equipment.
TABLE OF CONTENTS
Table of Contents
Chapter 1: Installation............................................................... 1
Introduction.............................................................................................1
Getting Started ........................................................................................1
Installation ..............................................................................................1
Introduction of I/O ports for each model.........................................2
Rack Mounting Your Rack Mount LCD KVM Assembly.........................3
Using the hotkey functions...............................................................5
Accessing and using the OSD menu ................................................7
Appendices ................................................................................ 9
Appendix A: Product Specifications .......................................................9
iii
iv Rack Mount LCD KVM Assembly Installer/User Guide
CHAPTER
1
Introduction
Supporting both USB and PS/2 interfaces, the Rack Mount LCD KVM
Assembly can control up to 16 servers. Built-in keyboard, video and
mouse (KVM) peripherals not only save valuable cabinet space, but also
enable direct channel selection via on-screen display (OSD) or keyboard
hotkeys.
Time-out and password protection offer secure access to the Rack
Mount LCD KVM Assembly, while the hot-plug feature allows for
uninterrupted switching and usage.
1
Installation
NOTE: The Rack Mount LCD KVM Assembly is also referred to as “the assembly”
interchangeably throughout this installer guide.
Getting Started
Before installing your Rack Mount LCD KVM Assembly, refer to the
following list to ensure you have all items that shipped with the
appliance, as well as other items necessary for proper installation.
Supplied with the Rack Mount LCD KVM Assembly
• Rack mount kit
• Power cable
• Ground terminator
Installation
If you are installing your Rack Mount LCD KVM Assembly to a PS/2
interface, you must turn off all servers before connecting your appliance
to a server for proper installation. USB interfaces do not need to be
turned off before installation.
2 Rack Mount LCD KVM Assembly Installer/User Guide
NOTE: Linux users may experience mouse failure if hot-plugging directly to the
assembly. If your mouse becomes locked, use the mouse reset hotkeys to reset
your mouse, or turn the Linux server off before connecting it to the assembly.
Introduction of I/O ports for each model
NOTE: For Taiwan customers only, 16-port models have the following model
numbers: AP17KMM16-101 and AP17KMM16-109; 8-port models have the
following model numbers: AP17KMM8-101 and AP17KMM8-109; and single-port
models have the following model numbers: AP17KMM-101 and AP17KMM-109.
Figure 1.1: Rear View of a 16-port Rack Mount LCD KVM Assembly
Table 1.1: Description of Figure 1.1
Number Description
1 Power input socket
2 Power switch
3 Ground
4 Console port
5 PC connection
ports (16)
Figure 1.2: Rear View of an 8-port Rack Mount LCD KVM Assembly
Table 1.2: Description of Figure 1.2
Number Description
1 Power input
socket
2 Power switch
Table 1.2: Description of Figure 1.2 (Continued)
Number Description
3 Ground
4 Console port
Chapter 1: Installation 3
5 PC connection
Figure 1.3: Rear View of a single-port Rack Mount LCD KVM Assembly
Table 1.3: Description of Figure 1.3
Number Description
1 Power input
2 Power switch
3 Ground
4 PC connection
CAUTION: To reduce the risk of electric shock or damage to your equipment:
- Plug the power cord into a grounded (earthed) outlet that is easily accessible at
all times.
- Disconnect the power from the unit by unplugging the power cord from either the
electrical outlet or the unit.
ports (8)
socket
port (1)
Rack Mounting Your Rack Mount LCD KVM Assembly
Your Rack Mount LCD KVM Assembly may be rack mounted using
brackets. Before installing the assembly, stabilize the rack in a permanent
location. Be sure to rack your Rack Mount LCD KVM Assembly in an
area of the cabinet that will allow you to utilize the LCD monitor,
keyboard and mouse funtions.
4 Rack Mount LCD KVM Assembly Installer/User Guide
CAUTION: Rack Loading - Overloading or uneven loading of racks may result in
shelf or rack failure, causing damage to equipment and possible personal injury.
Do not exceed your rack load rating.
Rear of rack
Front of rack
Figure 1.4: Rack mounting the assembly
To mount the Rack Mount LCD KVM Assembly:
1. Attach the front of the Rack Mount LCD KVM Assembly to the
front of your rack cabinet using the screws provided.
2. Standing behind the assembly, slide the mounting brackets into the
slots on the side of the unit.
3. Secure the brackets to the rear of the rack using the screws
provided.
To connect the Rack Mount LCD KVM Assembly:
1. Plug one end of the supplied power cord into the back of the
assembly and the other end into an appropriate power source.
2. Connect your servers to an available port on the rear of your Rack
Mount LCD KVM Assembly using the appropriate cable.
Chapter 1: Installation 5
3. Turn on all connected servers. Keyboard and mouse recognition is
now activated and your Rack Mount LCD KVM Assembly is ready
for operation.
After installation, turn on your Rack Mount LCD KVM Assembly and
then any attached computer. The default password is not required,
simply press
Enter to continue. Refer to the following table for a list of
push-button functions available via the LCD monitor.
Table 1.4: Monitor Push-button Functions
Button/LED Description
AUTO EXIT Exits from the OSD function or returns to
previous menu
SL (+ or -) Moves the selector right or left on the OSD
MENU SELECT Enables the OSD menu and controls the
LED (status light) Green = On
menu
function to be adjusted
Turns your Rack Mount LCD KVM Assembly
on or off
Flashing Green = power save mode or
disconnection of signal cable
Red = Off
Using the hotkey functions
The 8-port and 16-port version of the Rack Mount LCD KVM
Assembly features hotkey commands that allow you to easily access
various functions of your assembly. The following table explains the
hotkey functions available.
NOTE: To utilize the hotkey functions in the following table, press the Ctrl key on
the left side of the keyboard twice, then press the keys for the desired command.
6 Rack Mount LCD KVM Assembly Installer/User Guide
Table 1.5: Hotkey Commands and Descriptions
Function Keystrokes Description
Left Ctrl + Left Ctrl + 1-8
Selects the desired port channel by
number (port 1-8)
Port Switch
Left Ctrl + Left Ctrl + F1 - F8
Left Ctrl + Left Ctrl + Up or
Down Arrow
Selects port channels 9-16
The Up Arrow selects the next
channel; the
Down Arrow selects the
previous channel
Beep
Left Ctrl + Left Ctrl + B
Turns the beep function on or off in
Scan Mode (default is on)
Auto Scan
Left Ctrl + Left Ctrl+ S
Allows you to exit Auto Scan by
pressing any key
Reset
Left Ctrl + Left Ctrl + R
Resets the LCD KVM assembly
Assembly
Reset Mouse
Reset
Left Ctrl + Left Ctrl + M
Left Ctrl + Left Ctrl + K
Resets the mouse
Reset the keyboard
Keyboard
OSD Menu
Left Ctrl + Left Ctrl +
spacebar (or double-click
the right mouse button)
Displays the OSD menu
NOTE: The two consecutive left Ctrl keystrokes and the following command
key(s) should be pressed within two seconds or the hotkey sequence will not be
validated. Port number selections must be made using the numeric keys on the
keyboard. Numeric keys on the keypad are not available as hotkey commands.
Accessing and using the OSD menu
Right-click the mouse button twice or press Ctrl + Ctrl + Spacebar to
access the following OSD Menu.
Figure 1.5: OSD Menu
Table 1.6: OSD Menu Key
Heading Description
Chapter 1: Installation 7
NO. Port numbers
On line
System on
QV Quick view
Name Port name
A single click on the left mouse button allows you to switch to a chosen
PC port. Use the up or down arrows to highlight your selection, and then
press
Enter to make your selection.
8 Rack Mount LCD KVM Assembly Installer/User Guide
Table 1.7: OSD Functions
Function Key Submenu/Description
LST F1 All - Lists all ports
Scan F2 All - Scans all ports
Set F3 Scan Time - Sets scan time (default = 5 secs.)
Tool F4 Reset KVM - Press Enter to reset the KVM assembly
QV F5 Enables or disables Quick View
Name F6 Displays active port name
Lock
Console
Exit Esc Allows you to quit the OSD menu
Power On - Lists only ports that have a PC turned on
Quick View - Lists only Quick View ports
Power On - Scans only ports that have a PC turned on
Quick View - Scans only Quick View ports
Port Time - Sets port time (default = 5 secs.)
Console PWD - Sets console password (default = Enter)
Load Default - Sets load default values
Reset Mouse - Press Enter to reset the mouse
Reset Keyboard - Press Enter to reset the keyboard
Mouse On - Default is all ports. Toggle to Mouse Off and
press Enter to deselect available ports
Keyboard On - Default is all ports. Toggle to Keyboard Off
and press Enter to deselect available ports
F8 Locks your KVM console
APPENDICES
Appendices
Appendix A: Product Specifications
Table A.1: Rack Mount LCD KVM Assembly Specifications
LCD
LCD Type XGA TFT
Display Area 17”
Resolution 1280 x 1024
Luminance
Contrast Ratio 800:1 ( T Y P)
Back Light CCFL 2 lamps
Pixels Intervals (mm) 0.264 (H) x 0.264 (W)
LCD MTBF > 50,000 hour
250 cd/m
2
( T Y P)
9
Power Input 5V DC
Power Consumption < 40W
LCD OSD key
OSD Operation button 4 x Touch switches
LCD power source 1 x Sliding switch
Keyboard
Keys 82 keys + 17 number keys
Support IBM/AT
Interface PS/2 or USB
MTBF > 10,000,000 times
Mouse
X/Y Resolution >1000 point / inch, (40point/mm)
Hardware interface PS/2 or USB
Supports Windows
®
Me/NT/2000/XP/7
10 Rack Mount LCD KVM Assembly Installer/User Guide
Table A.1: Rack Mount LCD KVM Assembly Specifications (Continued)
Wheel Supports wheel function
Operating System
MTBF > 10,000,000 times
Assembly (8-port and 16-port
versions)
PC Connection Ports 8 or 16
PC Selection OSD Menu/Hotkey
Auto Scan Intervals 5-99 Secs
VGA Resolution 1920 x 1440
VGA Bandwidth 200 MHz
Power Supply
Alternating Current Input (A) 100-240VAC/50-60Hz/<1.5A
Supports Windows
®
Me/NT/2000/XP/7
MTBF >60,000 Hrs (25
° C)
Dimensions
(1 port) 13.69 kg/GW 18.79 kg
Net/Gross Weight
(8 port) 14.63 kg/GW 19.43 kg
(16 port) 14.79 kg/GW 19.59 kg
448 mm x 545 mm x 43 mm (1 port)
Unit Dimensions (W x D x H)
448 mm x 600 mm x 43 mm (8 port)
448 mm x 600 mm x 43 mm (16 port)
Package Size (W x D x H) 765 mm x 615 mm x 185 mm
Temperature 0-45
° C (Operating), -20 - 60° C (Storage)
Humidity 0-80%, Non-Condensing
For Technical Support:
www.avocent.com/support
590-940-501C
Loading...