Emerson CH Tanks Data Sheet

Transducerized Cleaning Tanks
Ultrasonic Cleaning
Transducerized Cleaning Tanks and Immersible Transducers
Branson manufactures five standard size transducerized 25 and 40kHz tanks that range from a 2.5 to a 50 gallon capacity (10 to 190 liters). All have drains and fills.
Type 316L bright-annealed stainless steel construction throughout permits the use of alkaline, mildly acidic, or neutral aqueous solutions. Branson tanks are available with or without integral heaters. Heated models are available to maintain solution temperatures up to 170oF (76oC). All models are available with a stainless steel parts basket and/or tank cover.
STANDARD FEATURES
Bottom-mounted positive drain
connection.
Fully shielded internal components.
OPTIONS
Stainless steel basket for parts
handling.
Stainless steel tank cover.
Thermostatically-controlled heat.
NUMBERING SYSTEM
Each Branson transducerized tank has a model number which contains impor­tant information to guide the selection of a properly rated comparison power supply. When making a selection, note the frequency.
For example: CH1012-40-12
This model number, stamped on the tank nameplate, indicates whether the tank has a heater (H = heated), the length of the tank in inches, left to right (10”), the width of the tank in inches, front to back (12”), the operating frequency (40kHz), and the number of attached piezoelectric transducer elements (12).
POWER SUPPLY SELECTION
To select the correct power supply for your transducerized tank, add the total number of transducer elements involved by using the information from the model number as explained. Then, select a power supply whose last two numbers exactly match the num­ber of transducer elements by referring
HEATED TANK SPECIFICATIONS
Model 610** Model 1012 Model 1216 Model 1620 Model 2024 Model 2032***
Tank 6” x 10” x 10” 10” x 12” x 10” 12” x 16” x 12” 16” x 20” x 16” 20” x 24” x 20” 20” x 32” x 20” Dimensions* (152 x 254 x 254 mm) (254 x 304 x 254 mm) (304 x 406 x 304 mm) (406 x 508 x 406 mm) (508 x 610 x 508 mm) (508 x 812 x 508 mm)
Overall
10” x 14” x 14.62” 14” x 16” x 15.62” 16” x 20” x 17.62” 20” x 24” x 21.75” 24” x 28” x 25.75” 26” x 36” x 25.75”
Dimensions* (254 x 355 x 356 mm) (356 xw406 x 397 mm) (406 x 508 x 447 mm) (610 x 609 x 552 mm) (609 x 711 x 654 mm) (660 x 914 x 654 mm
Capacity
Heater Wattage
Power Equipment 4.2 amps 8.4 amps 8.3 amps 12.5 amps 12.5 amps 22 amps
Approx. Shipping Wt. 35 lbs. (16 kg) 44 lbs. (20 kg) 68 lbs. (31 kg) 115 lbs. (52 kg) 165 lbs. (75 kg) 195 lbs. (89 kg)
* All dimensions are in order, left-to-right, front-to-back, and top-to-bottom. Allow 6 inches (153mm) clearance on front-to-back dimensions for connections. Bench mounting of tank requires bottom support.
** No fill
*** #8 polished stainless steel
to the power supply specifications on Bulletin S-1044 (Series 8500) or S1043 (Series 8300).
IMMERSIBLE TRANSDUCERS
Branson immersible ultrasonic trans­ducers can be placed wherever you need them in your existing cleaning tanks. These units give you the com­plete freedom to design specialized cleaning setups or to upgrade soak tanks with ultrasonics.
Each immersible transducer is fabri­cated from 316L bright annealed stainless steel with welded seams and stainless steel fittings. These hermeti­cally sealed modular components are available in standard sizes starting at 6” x 18” - all 3.25” deep. Other sizes can be custom-built for special appli­cations. Chrome plating is available to reduce cavitation erosion.
2.5 gallons (9.4 liters) 5.0 gallons (18.9 liters) 10 gallons (37.8 liters) 20 gallons (75.7 liters) 40 gallons (151.4 liters) 50 gallons (189.2 liters)
500 Watts 1000 Watts 2000 Watts 3000 Watts 3000 Watts 5000 Watts
120 V/IØ 120 V/IØ 220 V/IØ 220 V/IØ 220 V/IØ 220 V/IØ
Branson offers three transducer con­figurations which vary according to
frequency (40kHz), and that it
contains 12 piezoelectric elements. their mounting style and electrical connections. This allows for maxi­mum versatility of transducer place­ment on tank bottom or walls to permit optimum ultrasonic energy transmission. Whatever the configu­ration, Branson supplies all neces-
sary interconnecting components.
POWER SUPPLY FREQUENCY
SELECTION
Branson immersible transducers
may be used singly or in multiples,
powered by a Branson generator of
suitable capacity. The power supply
and all transducers must operate at
the same frequency. To select the
NUMBERING SYSTEM
Each Branson immersible transducer has a model number which contains important information useful for selection of a properly rated com­panion power supply.
For example: FC618-40-12 This model number, stamped on the transducer nameplate, indicates, a type FC mounting, the size of 6” wide by 18” long, the operating
correct power supply for a cleaning
setup, add the total number of
transducer elements involved by
using the information from the
model number as explained. Then,
select a power supply whose last two
numbers exactly match the number
of transducer elements. Multiple
power supplies may be required.
Refer to the power supply specifica-
tions chart on the front of this sheet.
IMMERSIBLE TRANSDUCER CONFIGURATIONS
Type EB - End Bulkhead
Type FC - Flexible Cable
ID-Engraving (bottom)
Radiating Surface
Mounting ange
ID Engraving (bottom)
Radiating Surface
Mounting ange
T
Branson offers three transducer configurations, Types FC, CB, and EB, which vary according to their mounting means and electrical connections.
Flexible Cable 4 inch minimum radius
Rack
Type FC — Most versatile type; does not require holes in the tank. May be side or bottom mounted using integral mount­ing flanges. Watertight 3’ lead-in cables required. Special cable lengths available, also right-angle fitting for tight-radius turns.
IMMERSIBLE TRANSDUCER MOUNTS & SPECIFICATIONS
Mounting ange
Type EB - End Bulkhead
FC-type immersible transducer
Flanged Junction Box
Jumper Cable
Radiating Surface
ID Engraving (bottom)
RF Cable
Mounting ange
CB-Type immersible transducers
Type CB — The most common style for side or bottom mount­ing. One or two bulkhead fittings, depending on transducer size. Supplied with 8’ RF cable, which allows master junction box to be remotely located. Special length cables available.
Radiating Surface
ID-Engraving (bottom)
RF cable to ultrasonic power supply
Junction box
Mounting ange
ype SB - Short Bulkhead
Radiating Surface
#10-32 Weldstuds
and Hardware
EB-type immersible
Transducers
EB Style
Junction Boxes
Type EB — For bottom-mount­ing, especially when under­tank clearance prevents use of Type CB. May be affixed to tank bottom using integral mounting flange. Standard 1-1/4” mounting fitting supplied; other lengths available.
ID Engraving
Mounting tting (2 places)
Tank Wall
RF Cable
Jumper RF Cable
Radiating Surface
ID Engraving
Type FC - Flexible Cable
Type CB - Cable Bulkhead
Model 610-6 Model 618-2
Dimensions* 6” X 10” 6” X 18” (Width x Length) (152 x 254 mm) (152 x 457 mm)
Approx. Shipping Wt. 18 lbs. (8 kg) 30 lbs. (14 kg)
* All transducers are 3-1/4” (82 mm) deep. Stated dimensions do not include
mounting flanges on types FC and EB. Other sizes or custom-made transducers are available upon request. Chrome plating and high-frequency units are also available. Note: Opposed side-mounted transducers should have at least 12”of space between radiating faces.
Ultrasonic Cleaning
Ultrasonic Cleaning
Global Technologies. Local Solutions.
Transducerized Cleaning Tanks
Branson’s unmatched global resources ensure optimal solutions for the most challenging materials joining and precision cleaning applications.
With 1600+ employees in over 70 sites worldwide, we can rapidly respond to our customers’ needs, wherever they are located. Bran- son understands local markets and regulations, and the open collabo- ration among our global offices and extensive staff of application specialists quickly produces solu- tions for customers. We partner with companies of every size and scope to help resolve critical issues
ranging from market changes, product quality/life cycles and production costs, to employee safety and environmental compli- ance. And, Branson's commitment to the publicly funded industrial collective research initiative and cooperation with various research centers have produced widespread innovations in plastics joining technology that are benefiting companies everywhere.
Branson is a leading innovator in the Industrial Automation division of Emerson, a diversified global manufacturing and technology company. Emerson is a progressive
company working to develop products and processes to resolve global issues, including energy supply and distribution, information and networking, climate and environment, manufacturing efficiency, and product performance. Emerson is dedicated to the pursuit of breakthrough technology developments never before envisioned.
Branson brings exceptional quality, fast delivery and competi- tive prices for your tooling needs. Contact your nearest regional center today.
Americas
Branson Ultrasonics Corp. 41 Eagle Road Danbury, CT 06813-1961 T: 800-732-9262 F: 203- 796-2250 www.bransonultrasonics.com
Europe
Branson Ultraschall Niederlassung der Emerson Technologies GmbH & Co. OHG Waldstrasse 53-55 63128 Dietzenbach, Germany T: +49-6074-497-0 F: +49-6074-497-199 www.branson.eu
Asia
Branson Ultrasonics (Shanghai) Co., Ltd. 758 Rong Le Dong Road Song Jiang, Shanghai, PRC, 201613 T: 86-21-3781-0588 F: 86-21-5774-5100 www.branson-china.com
Transducerized Cleaning Tanks and Immersible Transducers
© Branson Ultrasonics Corporation 2013
The Emerson logo is a trademark and service mark of Emerson
Electric Co. Revised and printed in the U.S.A. 4/13
Loading...