Page 1
EIOA8*1D EIOA8*2D EIOA8*3D
With FLEXI-GUARD
®
Installation/Care/Use Manual
USES HFC-134A REFRIGERANT
20
19
46
21
22, 23, 24, 25
26, 27
28
54
47, 48, 49, 50, 51
18
38
52
53
SEE FIG. 3
SEE FIG. 4
34
18
35
37
12
43, 44, 45
FIG. 1
PAGE 1
36
18
42
39, 40, 41
97410C (Rev. G - 12/01)
Page 2
EIOA8*1D EIOA8*2D EIOA8*3D
*ADA REQUIREMENT
*REQUISITO DE A.D.A.
*EXIGENCE ADA
FINISHED FLOOR
PISO ACABADO
PLANCHER FINI
CAJA RECESIVA DE ALAMBRES (3) DE SUMINISTRO ELÉCTRICO
BOÎTE ENCASTRÉE DALIMENTATION ÉLECTRIQUE (3) FILS
ASEGURE UNA VENTILACIÓN ADECUADA MANTENIENDO UN ESPACIO E 6" (152 mm) (MÍN.) DE HOLGURA ENTRE LA
REJILLA DE VENTILACIÓN DEL MUEBLE Y LA PARED
ASSUREZ-VOUS UNE BONNE VENTILATION EN GARDANT 6" (152 mm) (MIN.) ENTRE LES ÉVENTS DE LENCEINTE ET
LE MUR.
AGUJEROS DE LAS TUERCAS DE 7/16 PARA SUJETAR LA UNIDAD A LA PARED
WALL.
D = ELECTRICAL SUPPLY (3) WIRE RECESSED BOX
FIG. 2
E = INSURE PROPER VENTILATION BY MAINTAINING 6" (152 mm) (MIN.) CLEARANCE FROM CABINET LOUVERS TO
TROUS DÉCROUS 7/16 POUR FIXER LAPPAREIL AU MUR
F = 7/16 BOLT HOLES FOR FASTENING UNIT TO WALL
97410C (Rev. G - 12/01)
PAGE 2
FROM WALL SHUT OFF BY OTHERS
(38 mm) FUERA DE LA LLAVE DE PASO EN LA PARED COLOCADA POR TERCEROS.
CONNECTANT UNE TUYAUTERIE DE 1-1/2 PO. (38 mm) DEPUIS LE ROBINET D'ARRÊT FOURNI PAR D'AUTRES.
UBICACIÓN RECOMENDADA PARA EL DRENAJE DE SALIDA DE AGUA, DE 1¼ DE DIÁMETRO.
EMPLACEMENT RECOMMANDÉ POUR LE DRAIN DE D.E. 1-1/4" DE SORTIE DEAU.
SE RECOMIENDA UBICAR EL TUBO CORTO DE CONEXIÓN AL TUBO DE COBRE SIN CHAPAR DE 3/8" DE DIÁM. EXT. A 1-1/2"
LEGEND/LEYENDA/LÉGENDE
A = RECOMMENDED WATER SUPPLY LOCATION 3/8 O.D. UNPLATED COPPER TUBE CONNECT STUB 1-1/2 IN. (38 mm) OUT
EMPLACEMENT RECOMMANDÉ D'ALIMENTATION EN EAU PAR TUBE EN CUIVRE NON PLAQUÉ DE 3/8 PO. (9,5 mm) D.E.
PURGADOR DE 1¼ NO PROPORCIONADO**
B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/4 O.D. DRAIN
C = 1-1/4 TRAP NOT FURNISHED**
SIPHON 1-1/4 NON FOURNI**
Page 3
EIOA8*1D EIOA8*2D EIOA8*3D
SENSOR RANGE ADJUSTMENT: The electronic sensor used in this cooler is factory pre-set for a "visual" range of 36
inches (914 mm). If actual range varies greatly from this or a different setting is desired, follow the range adjustment
procedure below:
A. Remove front panel of cooler.
B. Using a small tip screwdriver, rotate range adjustment screw clockwise to increase range and counterclockwise to
decrease range (See Fig. 3).
CAUTION: Complete range of sensor (24-28 inches/610-711mm) is only one turn of the adjusting screw.
C. Replace front panel.
SENSOR CONTROL: If sensor fails to operate valve mechanism or operates erratically, check the following.
A. Ensure there are no obstructions within a 40 inch (1016mm) radius in front of cooler.
B. Check wire connections at the solenoid valve and sensor. CAUTION: Make sure unit is unplugged before checking any
wiring.
C. Ensure proper operation of solenoid valve. If there is an audible clicking sound yet no water flows, look for an obstruction
in the valve itself or elsewhere in the water supply line.
RANGE
ADJUSTMENT
SCREW
3
16
15
10
NOTE: WATER FLOW DIRECTON
6
14
13
FIG. 3
7
14
HANGER BRACKETS & TRAP
1) Remove hanger bracket fastened to back of cooler by re-
moving one (1) screw.
2) Mount the hanger bracket and trap as shown in Figure 2.
NOTE: Hanger Bracket MUST be supported securely. Add
fixture support carrier if wall will not provide adequate support.
IMPORTANT:
7-3/4 in. (197mm) dimension from wall to centerline of
trap must be maintained for proper fit.
Anchor hanger securely to wall using all six (6) 1/4 in. dia.
mounting holes.
3) Install straight valve for 3/8" O.D. tube.
4) Hang the cooler on the hanger bracket. Be certain the
hanger bracket is engaged properly in the slots on the
cooler back as shown in Figure 2.
5) Loosen the two (2) screws holding the lower front panel at
the bottom of cooler base and two (2) screws at the top.
Remove the front panel and set aside.
6) Connect water inlet line--See Note 4 of General Instructions.
7) Remove the slip nut and gasket from the trap and install
them on the cooler waste line making sure that the end of
the waste line fits into the trap. Assemble the slip nut and
gasket to the trap and tighten securely.
Also See General Instructions
8) Stream height is factory set at 35 PSI. If supply
pressure varies greatly from this, adjust screw, accessible by removing front panel (Item 7, Fig. 3).
CW adjustment will raise stream and CCW adjustment will lower stream. For best adjustment, stream
should hit basin approximately 6-1/2 (165mm) from
bubbler.
9) Replace the front panel and secure by retightening
four (4) screws.
INSTALLATION
INSTALLATION OF COOLER
START UP
8
4
2
11
12
56
ITEM NO. PART NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
PANEL
COLOR
Bronzetone
Gray Beige
Almond
Stainless Stl
Sandalwood
Granite
PAGE 3
9
17
9
1
14
22897C
26729C
31516C
35783C
31272C
35784C
See Color Table
See Color Table
See Color Table
70817C
75507C
56082C
70644C
75532C
40045C
70864C
61314C
50986C
70002C
COLOR TABLE
Item No. 5
Part No.
27502C
23015C
23016C
22822C
23017C
23020C
5
DESCRIPTION
Panel-Bottom Dispenser
Bracket-Valve Mounting
Sensor-Clear (115V)
Sensor-Clear (230V)
Solenoid Valve (115V)
Solenoid Valve (230V)
Panel-Right Side
Panel-Left Side
Panel-Front
Elbow 1/4 Stem x 1/4 O.D.
Fitting 1/4 NPTF x 1/4 O.D.
Nut-Regulator
Screw-#6-32 x 1/2" Lg. PHMS
Screw-#10 x 1/2" Lg. THSM
Hex Nut
Screw-#8 x 5/8" Lg. Torx/Slot
Regulator
Holder-Regulator
Screw-#10 x 1/2" Lg. HHSM
Item No. 6
Part No.
27432C
23008C
23009C
22814C
23010C
23013C
97410C (Rev. G - 12/01)
Item No. 7
Part No.
27591C
23161C
23162C
23137C
23164C
27217C
Page 4
EIOA8*1D EIOA8*2D EIOA8*3D
ITEM NO. PART NO.
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42*
43
44
45
46
47
48
49
50
51
52
53
54
55
56
NS
70002C
55996C
66534C
31483C
30699C
70018C
31490C
70009C
22899C
38417001
56092C
51349C
51350C
40322C
40066C
50934C
50168C
50373C
70012C
62152C
66202C
See Color Table
See Color Table
See Color Table
101516143550
100806740570
19037000
35960C
35959C
35768C
35958C
66576C
40614C
50400C
50401C
70444C
70016C
31513C
See Color Table
21903C
27534C
See Color Table
400660943730
PARTS LIST 115V
DESCRIPTION
Screw-#10 x 1/2"Lg. HHSM
Strainer
Evaporator Assembly
Power Cord
Fan Blade
Hex Nut - Fan Blade
Fan Motor 115V
Screw - Fan Motor
Shroud - Fan
Screw - #8-18 x 3/8" Lg. (Fan Shroud)
Poly Tubing (Cut To Length)
Bubbler Assembly
Bubbler Assembly - Bronzetone
Orifice Assembly
Orifice Assembly - Bronzetone
Guard
Pedestal
Pedestal - Bronzetone
Locknut
Condenser
Drier
Panel -Right Rear
Panel -Left Rear
Panel - Front Lower
Stud - Compressor Mtg.
Grommet - Compressor Mtg.
Clip - Compressor Mtg.
Compressor Serv. Pak EM65
Relay
Cover - Relay
Overload
Heat Exchanger
Drain Tube
Gasket - Drain
Ring Support - Drain
Clamp - Drain Gasket
Hex Nut #10-32
Cold Control
Adaptor - Basin
Basin
Basin - Bronzetone
Cover-Dispenser Bottom
Hanger Bracket
PARTS LIST 220V/50Hz
ITEM NO. PART NO.
21
24
42*
43
46
35987C
31431C
36085C
36049C
36050C
66561C
PARTS LIST 230V/60Hz
ITEM NO. PART NO.
21
24
42*
43
44
46
35987C
31431C
35842C
N/A
N/A
66561C
WIRING DIAGRAM
This Drawing is merely for illustrating the
components of the electrical system.
31
DESCRIPTION
Power Cord
Fan Motor
Compressor Serv. Pak
Overload
Relay
Heat Exchanger
DESCRIPTION
Power Cord
Fan Motor
Compressor Serv. Pak
Overload/Relay
Cover-Relay
Heat Exchanger
*INCLUDES RELAY & OVERLOAD. IF UNDER WARRANTY, REPLACE WITH
SAME COMPRESSOR USED IN ORIGINAL ASSEMBLY.
NOTE: All correspondence pertaining to any of the above water coolers or
orders for repair parts MUST include Model No. and Serial No. of cooler,
name and part number of replacement part.
CAUTION: Cleaning of Bronzetone Models requires special care. Outer
surfaces must be cleaned with a mild detergent or mixture of vinegar and
water only, rinsed and wiped dry. Abrasive and acidic cleaners may eventually damage the Bronzetone finish.
COLOR TABLE
PANEL
COLOR
Bronzetone
Gray Beige
Almond
Stainless Steel
Sandalwood
Granite
PRINTED IN U.S.A.
ELKAY MANUFACTURING COMPANY 2222 CAMDEN COURT OAK BROOK, IL 60523 630.574.8484
97410C (Rev. G - 12/01)
Item No. 36
Part No.
27490C
22967C
22968C
22862C
22969C
22972C
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.323.0620
Item No. 37
Part No.
27486C
22960C
22961C
22854C
22962C
22965C
PAGE 4
Item No. 38
Part No.
27498C
22953C
22954C
22955C
22956C
27214C
29
30
32
BASIN
33
NOTE:
WHEN INSTALLING REPLACEMENT BUBBLER
AND PEDESTAL, TIGHTEN NUT (ITEM 33)
ONLY TO HOLD PARTS SNUG IN POSITION.
DO NOT OVER TIGHTEN.
FIG. 4
Item No. 53
Part No.
51552C
51551C
51552C
51551C
51552C
51551C
Item No. 56
Part No.
55930C
55931C
55930C
55931C
55930C
55931C
Loading...