Elkay EHWM14FP Installation Manual

EHWM14FP*A EHWM17FP*A

Installation/Care/Use Manual

Heavy Duty 14 Gauge Barrier Free Slimline

Freeze Resistant Fountains

®

EHWM14FP

EHWM17FP

Installer
T o assure you install this model easily and correctly , PLEASE READ THESE SIMPLE
INSTRUCTIONS BEFORE ST ARTING THE INST ALLA TION. CHECK YOUR INST ALLA­TION FOR COMPLIANCE WITH PLUMBING , ELECTRICAL AND OTHER APPLICABLE
CODES. After installation, leave these instructions inside the fountain for future reference.
This Freeze Resistant Fountain is shipped in two separate cartons. The second carton(s)
contains the Freeze Resistant Package(s) LKFRB1 that are installed on an interior
heated wall. The interior space must maintain a minimum temperature of 50° F (10° C).
Refer to the Freeze Resistant Package for the rough-in dimensions for installation.

IMPORTANT

ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON

IMPORTANT! INSTALLER PLEASE NOTE.

THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO
WA TER LINES IS A COMMON PROCEDURE. THIS GROUNDING MA Y BE IN THE BUILDING OR MA Y
OCCUR A WA Y FROM THE BUILDING . THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK
INTO A FOUNT AIN, CREA TING AN ELECTROLYSIS WHICH CAUSES A METALLIC T ASTE OR AN
INCREASE IN THE METAL CONTENT OF THE WATER. THIS CONDITION IS A VOIDABLE BY USING
THE PROPER MA TERIALS AS INDICA TED. ANY DRAIN FITTINGS PROVIDED BY THE INST ALLER
SHOULD BE MADE OF PLASTIC TO ELECTRICALL Y ISOLA TE THE FOUNT AIN FROM THE BUILDING
PLUMBING SYSTEM.

PAGE 1 98402C (Rev. A - 5/08)

EHWM14FP*A EHWM17FP*A

43 3/4"

1111mm

29 1/2"

749mm

29 1/16"

D

E

3 1/8"

79mm

C

5 1/4"

133mm

16"

406mm

5 1/4"

133mm

8"

203mm

739mm

28"

711mm

Finished Floor

EHWM14FP

MOUNTING BOLT AND ACCESS HOLE LAYOUT

B

A

6"

WALL PLATE

152mm

ASSEMBLY

7 1/4"

184mm

12 1/8"

307mm

26"

660mm

24 11/16"

628mm

FIG . 1

12"

305mm

MAX. WALL

THICKNESS

PAGE 298402C (Rev. A - 5/08)

LEGEND

A = 1-3/4" DIA. (44mm) HOLE FOR W ASTE LINE

B = 7/8" DIA. (22mm) HOLE FOR WA TER

SUPPLY TUBE

C = 7/8" DIA. (22mm) HOLE FOR OPERA TING

CABLE

D = 1/4" DIA. (6mm) HOLES FOR MOUNTING

PLA TE TO WALL

E = 3/8" DIA. (10mm) HOLES FOR MOUNTING

PLA TE TO WALL

EHWM14FP*A EHWM17FP*A

2 5/8"

66mm

3 5/8"

91mm

12 3/8"

315mm

13 3/8"

340mm

16 7/8"

429mm

33"

838mm

Orifice Height

12"

305mm

MAX. WALL

THICKNESS

5/8"

16mm

18"

457mm

28"

711mm

18 3/4"

477mm

Finished Floor

* Adult ADA Requirement

**24" for Child ADA, adjust other

measurements accordingly.

EHWM14FP

ROUGH-IN DRA WINGS

3 13/16"

97mm

19 3/4"

502mm

12 1/8"

309mm

FIG . 2

4 3/8"

111mm

20 3/8"

518mm

27"

686mm

*

24 1/2"

622mm

1. Wall should already be framed for the fountain using dimensions shown in Fig. 1. Shown dimensions pertain to installation location.

These dimensions are required for compliance with ANSI Standard A117.1. and ADA (Framing shown for reference only).

2. Remove bottom cover from fountain and save the screws.

3. Install the fountain using bolts and washers (provided). Tighten securely.

4. Attach drain tube to fountain and cut to required length using the freeze resistant box as a guide.

5. Install freeze-resistant box - see box instructions.

6. Replace bottom cover.

PAGE 3 98402C (Rev. A - 5/08)