Elkay EHW214FPK Installation Manual
EHW214FP*A EHWM214FP*A EHW217FP*A EHWM217FP*A EHW217FPRA*A EHWM217FPRA*A
Installation/Care/Use Manual
EHW214FP EHWM214FP EHW217FP EHWM217FP
EHW217FPRA EHWM217FPRA
Freeze Resistant Fount ain
EHW214FP EHW217FP EHW217FPRA
Installer
T o assure you install this model easily and correctly , PLEASE READ THESE SIMPLE
INSTRUCTIONS BEFORE ST ARTING THE INST ALLA TION. CHECK YOUR INST ALLATION FOR COMPLIANCE WITH PLUMBING , ELECTRICAL AND OTHER APPLICABLE
CODES. After installation, leave these instructions inside the fountain for future reference.
This Freeze Resistant Fountain is shipped in two separate cartons. The second carton(s)
contains the Freeze Resistant Package(s) LKFRB1 that are installed on an interior
heated wall. The interior space must maintain a minimum temperature of 50° F (10° C).
Refer to the Freeze Resistant Package for the rough-in dimensions for installation.
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON
IMPORTANT! INSTALLER PLEASE NOTE.
THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO
WA TER LINES IS A COMMON PROCEDURE. THIS GROUNDING MA Y BE IN THE BUILDING OR MA Y
OCCUR A WA Y FROM THE BUILDING . THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK
INTO A FOUNT AIN, CREA TING AN ELECTROLYSIS WHICH CAUSES A METALLIC T ASTE OR AN
INCREASE IN THE METAL CONTENT OF THE WATER. THIS CONDITION IS A VOIDABLE BY USING
THE PROPER MA TERIALS AS INDICA TED. ANY DRAIN FITTINGS PROVIDED BY THE INST ALLER
SHOULD BE MADE OF PLASTIC TO ELECTRICALL Y ISOLA TE THE FOUNT AIN FROM THE BUILDING
PLUMBING SYSTEM.
PAGE 1 98420C (Rev. C - 7/09)
EHW214FP*A EHWM214FP*A EHW217FP*A EHWM217FP*A EHW217FPRA*A EHWM217FPRA*A
43 5/8"
1108mm
30 1/4"
768mm
29 7/8"
759mm
"C"
3"
5 1/4"
133mm
8"
203mm
16"
406mm
8"
203mm
5 1/4"
133mm
"D"
76mm
"B"
"A"
"E"
28 9/16"
725mm
FINISHED FLOOR
24 9/16"
625mm
EHWM214FP WITH WALL PLATE ASSEMBLY
MOUNTING BOLT AND ACCESS HOLE LAYOUT
7 1/4"
184mm
WALL PLATE ASSEMBLY
7 1/4"
185mm
12 1/8"
308mm
26 13/16"
681mm
FIG . 1
12"
305mm
MAX. WALL
THICKNESS
LEGEND
A = 1-3/4" DIA.(44 mm) HOLE FOR WASTE LINE
B = 7/8" DIA. (22mm) HOLE FOR WATER SUPPLY
C = 7/8" DIA. (22mm) HOLE FOR OPERATING CABLE
D = 1/4" DIA. (6 mm ) HOLE FOR MOUNTING PLATE TO WALL
E = 3/8" DIA. (6mm) HOLE FOR MOUNTING PLATE TO WALL
PAGE 298420C (Rev. C - 7/09)
EHW214FP*A EHWM214FP*A EHW217FP*A EHWM217FP*A EHW217FPRA*A EHWM217FPRA*A
28 13/16"
732mm
17 15/16"
455mm
14 7/16"
366mm
13 3/8"
339mm
ROUGH-IN DRA WINGS
EHWM214FP WITH WALL PLATE ASSEMBLY
5/8"
16mm
3 5/8"
91mm
2 5/8"
66mm
18"
457mm
12"
305mm
MAX. WALL
THICKNESS
FINISHED FLOOR
6 1/2"
167mm
ADA
27"
686mm
REQUIREMENT
12 1/8"
19 3/4"
502mm
309mm
FIG . 2
20 3/8"
518mm
1. Wall should already be framed for the fountain using dimensions shown in Fig. 1. Shown dimensions pertain to installation location.
These dimensions are required for compliance with ANSI Standard A117.1. and ADA (Framing shown for reference only).
2. Remove bottom cover from fountain and save the screws.
3. Install the fountain using bolts and washers (provided). Tighten securely.
4. Attach drain tube to fountain and cut to required length using the freeze resistant box as a guide.
5. Install freeze-resistant box - see box instructions.
6. Replace bottom cover.
PAGE 3 98420C (Rev. C - 7/09)
EHW214FP*A EHWM214FP*A EHW217FP*A EHWM217FP*A EHW217FPRA*A EHWM217FPRA*A
43 1/2"
1105mm
28 9/16"
725mm
30 1/4"
768mm
1 5/16"
33mm
1 7/8"
48mm
8"
203mm
16"
406mm
8"
203mm
3 1/8"
79mm
A
B
C
D
HANGER BRACKET
BACK PANEL
MPW101
MTG. PLT.
FINISHED FLOOR
EHW214FP WITH MPW101 MOUNTING PLATE
MOUNTING BOLT AND ACCESS HOLE LAYOUT
FIG . 3
7 1/4"
184mm
12 1/8"
307mm
12"
305mm
MAX. WALL
THICKNESS
LEGEND
A = 1-3/4" DIA.(44 mm) HOLE FOR WASTE LINE
B = 7/8" DIA. (22mm) HOLE FOR WATER SUPPLY
C = 7/8" DIA. (22mm) HOLE FOR OPERATING CABLE
D = 1/4" DIA. (6 mm ) HOLE FOR MOUNTING PLATE TO WALL
PAGE 498420C (Rev. C - 7/09)
EHW214FP*A EHWM214FP*A EHW217FP*A EHWM217FP*A EHW217FPRA*A EHWM217FPRA*A
28 9/16"
725mm
17 1/2"
444mm
14"
355mm
3 5/8"
13"
330mm
MPW101 MTG. PLT.
REF. SEPARATE
INSTALLATION
INSTRUCTIONS
FOR DETAILS
5/8"
16mm
91mm
2 5/8"
66mm
ROUGH-IN DRA WINGS
EHW214FP WITH MPW101 MOUNTING PLATE
19 3/4"
502mm
FINISHED WALL
12"
305mm
MAX. WALL
THICKNESS
18"
457mm
FINISHED FLOOR
3 13/16"
97mm
6 1/2"
165mm
12 1/8"
308mm
27"
ADA
686mm
REQUIREMENT
FIG . 4
20 3/8"
518mm
1. Wall should already be framed for the fountain using dimensions shown in Fig. 1. Shown dimensions pertain to installation location.
These dimensions are required for compliance with ANSI Standard A117.1. and ADA (Framing shown for reference only).
2. Remove bottom cover from fountain and save the screws.
3. Install the fountain using bolts and washers (provided). Tighten securely.
4. Attach drain tube to fountain and cut to required length using the freeze resistant box as a guide.
5. Install freeze-resistant box - see box instructions.
6. Replace bottom cover.
PAGE 5 98420C (Rev. C - 7/09)
Loading...