Page 1
EHOA8*1C, 2C
With FLEXI-GUARD
®
Installation/Care/Use Manual
USES HFC-134A REFRIGERANT
46
43, 44,
45
25
21
SEE FIG. 3
19
27, 47
SEE FIG. 4
49
18
42
51
53
50
52
39, 40, 41
53
33
22, 23, 24
26
34
51
54
38
35, 36, 3748
20
FIG. 1
PAGE 1
97376C (Rev. C - 10/02)
Page 2
EHOA8*1C, 2C
FINISHED FLOOR
PISO ACABADO
PLANCHER FINI
ASEGURE UNA VENTILACIÓN ADECUADA MANTENIENDO UN ESPACIO E 6" (152mm) (MÍN.) DE HOLGURA ENTRE LA
REJILLA DE VENTILACIÓN DEL MUEBLE Y LA PARED
ASSUREZ-VOUS UNE BONNE VENTILATION EN GARDANT 6" (152mm) (MIN.) ENTRE LES ÉVENTS DE LENCEINTE ET LE
MUR
CABLE ELÉCTRICO DE 1½ PIE, 457 mm DE LARGO
CORDON DALIMENTATION 1-1/2' (457mm)
UBICACIÓN ALT. DE LA TOMA DE ELECTRICIDAD
EMPLACEMENT ALTERNATIF DE LA PRISE DE COURANT
ESTE AGUJERO DE TUERCA DEBERÁ SER USADO PARA ASEGURAR LA UNIDAD A LA PARED.
ON DOIT UTILISER CE TROU DE BOULON POUR INSTALLER LAPPAREIL AU MUR.
ALTURA DEL ORIFICIO 1-1/4" (32mm) SOBRE LA CORONA
HAUTEUR DE L'ORIFICE 1-1/4" (32mm) AUDESSUS DU REBORD
E = INSURE PROPER VENTILATION BY MAINTAINING 6" (152mm) (MIN.) CLEARANCE FROM CABINET LOUVERS TO WALL.
F = POWER CORD 1-1/2FEET (457mm) LONG
G = ALT. ELECTRICAL OUTLET LOCATION
H = THIS BOLT HOLE MUST BE USED FOR FASTENING UNIT TO WALL.
J = ORIFICE HEIGHT 1-1/4" (32mm) ABOVE RIM
FIG. 2
97376C (Rev. C - 10/02)
PAGE 2
FROM WALL SHUT OFF BY OTHERS
1/2" (38mm) FUERA DE LA LLAVE DE PASO EN LA PARED COLOCADA POR TERCEROS.
CONNECTANT UNE TUYAUTERIE DE 1-1/2 PO. (38mm) DEPUIS LE ROBINET D'ARRÊT FOURNI PAR D'AUTRES.
UBICACIÓN RECOMENDADA PARA EL DRENAJE DE SALIDA DE AGUA, DE 1¼ DE DIÁMETRO.
EMPLACEMENT RECOMMANDÉ POUR LE DRAIN DE D.E. 1-1/4" DE SORTIE DEAU.
PURGADOR DE 1¼ NO PROPORCIONADO**
SIPHON 1-1/4 NON FOURNI**
UBICACIÓN DE LA TOMA DE ELECTRICIDAD
SE RECOMIENDA UBICAR EL TUBO CORTO DE CONEXIÓN AL TUBO DE COBRE SIN CHAPAR DE 3/8" DE DIÁM. EXT. A 1-
LEGEND/LEYENDA/LÉGENDE
A = RECOMMENDED WATER SUPPLY LOCATION 3/8 O.D. UNPLATED COPPER TUBE CONNECT STUB 1-1/2 IN. (38mm) OUT
EMPLACEMENT RECOMMANDÉ D'ALIMENTATION EN EAU PAR TUBE EN CUIVRE NON PLAQUÉ DE 3/8 PO. (9,5 mm) D.E.
B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/4 O.D. DRAIN
C = 1-1/4 TRAP NOT FURNISHED**
EMPLACEMENT DE LA PRISE DE COURANT
D = ELECTRICAL OUTLET LOCATION
Page 3
EHOA8*1C, 2C
SENSOR RANGE ADJUSTMENT: The electronic sensor used in this cooler is factory pre-set for a "visual" range of 36
inches (914 mm). If actual range varies greatly from this or a different setting is desired, follow the range adjustment
procedure below:
A. Remove front panel of cooler.
B. Using a small tip screwdriver, rotate range adjustment screw clockwise to increase range and counterclockwise to
decrease range (See Fig. 3).
CAUTION: Complete range of sensor (24-28 inches/610-711mm) is only one turn of the adjusting screw.
C. Replace front panel.
SENSOR CONTROL: If sensor fails to operate valve mechanism or operates erratically, check the following.
A. Ensure there are no obstructions within a 40 inch (1016mm) radius in front of cooler.
B. Check wire connections at the solenoid valve and sensor. CAUTION: Make sure unit is unplugged before checking any
wiring.
C. Ensure proper operation of solenoid valve. If there is an audible clicking sound yet no water flows, look for an obstruction
in the valve itself or elsewhere in the water supply line.
13
RANGE ADJUSTMENT SCREW
10
3
16
NOTE: WATER FLOW DIRECTON
15
6
14
FIG. 3
14
7
HANGER BRACKETS & TRAP
INSTALLATION
1) Remove hanger bracket fastened to back of cooler by re-
moving one (1) screw.
2) Mount the hanger bracket and trap as shown in Figure 2.
NOTE: Hanger Bracket MUST be supported securely. Add
fixture support carrier if wall will not provide adequate support.
IMPORTANT:
7-3/4 in. (197mm) dimension from wall to centerline of trap
must be maintained for proper fit.
Anchor hanger securely to wall using all six (6) 1/4 in. dia.
mounting holes.
3) Install straight valve for 3/8" O.D. unplated copper tube.
INSTALLATION OF COOLER
4) Hang the cooler on the hanger bracket. Be certain the
hanger bracket is engaged properly in the slots on the
cooler back as shown in Figure 2.
5) Loosen the two (2) screws holding the lower front panel at
the bottom of cooler base and two (2) screws at the top.
Remove the front panel and set aside.
6) Connect water inlet line--See Note 4 of General Instructions.
7) Remove the slip nut and gasket from the trap and install
them on the cooler waste line making sure that the end of
the waste line fits into the trap. Assemble the slip nut and
gasket to the trap and tighten securely.
START UP
Also See General Instructions
8) Stream height is factory set at 35 PSI. If supply
pressure varies greatly from this, adjust screw, accessible by removing front panel (Item 7, Fig. 3). CW
adjustment will raise stream and CCW adjustment
will lower stream. For best adjustment, stream should
hit basin approximately 6-1/2 (165mm) from bubbler.
9) Replace the front panel and secure by retightening
four (4) screws.
12
11
2
1
4
ITEM NO. PART NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
PANEL
COLOR
Gray Beige
Almond
Stainless Stl
Sandalwood
Granite
Light Gray
8
17
9
9
14
26588C
26866C
31516C
35783C
31272C
35784C
See Color Table
See Color Table
See Color Table
70817C
75507C
56082C
70644C
75497C
40045C
70864C
50986C
61314C
70002C
COLOR TABLE
Item No. 5
Part No.
26635C
26636C
26637C
26638C
26641C
26642C
5
DESCRIPTION
Panel-Bottom Dispenser
Bracket-Valve Mounting
Sensor-Clear (115V)
Sensor-Clear (230V)
Solenoid Valve (115V)
Solenoid Valve (230V)
Panel-Right Side
Panel-Left Side
Panel-Front
Elbow 1/4 Stem x 1/4 O.D.
Fitting 1/4 NPTF x 1/4 O.D.
Nut-Regulator
Screw-#6-32 x 1/2" Lg. PHMS
Screw-#10 x 1/2" Lg. PHSM
Hex Nut
Screw-#8 x 5/8" Lg. Torx/Slot
Holder-Regulator
Regulator
Screw-#10 x 1/2" Lg. HHSM
Item No. 6
Item No. 7
Part No.
26605C
26606C
26607C
26608C
26611C
26612C
Part No.
26731C
26732C
26733C
26734C
26737C
26738C
PAGE 3
97376C (Rev. C - 10/02)
Page 4
EHOA8*1C, 2C
PARTS LIST 115V
ITEM NO. PART NO.
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38*
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
27097C
See Color Table
31483C
27095C
30699C
70018C
31490C
70009C
50186C
70241C
56073C
40322C
55997C
56011C
75580C
62152C
66202C
50144C
70184C
70150C
35947C
31039C
35768C
35935C
66501C
40572C
40575C
50074C
21222C
70208C
31513C
66505C
55996C
27093C
27094C
27096C
56092C
*INCLUDES RELAY & OVERLOAD. IF UNDER WARRANTY, REPLACE
WITH SAME COMPRESSOR USED IN ORIGINAL ASSEMBLY.
NOTE: All correspondence pertaining to any of the above water coolers or
orders for repair parts MUST include Model No. and Serial No. of cooler,
name and part number of replacement part.
Frame-Back/Bottom
Wrapper
Power Cord
Fan Bracket
Fan Blade
Hex Nut - Fan Blade
Fan Motor 115V
Screw - Fan Motor
Shroud - Fan
Clip (Front and Rear Panels)
Bubbler Assembly
Orifice Assembly
Pedestal
Housing Assembly
Locknut
Condenser
Drier
Grommet - Compressor Mtg.
Hair Pin - Cotter
Washer
Compressor Serv. Pak EM65
Overload/Relay P600B/427NFBYY
Cover - Relay
Capacitor - Run
Heat Exchanger
Tailpipe
Strainer Assy
Gasket - Tailpipe
Basin
Screw - Basin Mtg.
Cold Control
Evaporator Assy
Strainer
Angle - Bracket Corner
Bracket - Front Support
Bracket - Basin Mtg.
Poly Tubing (Cut To Length)
DESCRIPTION
PARTS LIST 230V
ITEM NO. PART NO.
24
*38
40
41
42
-
31430C
35763C
31024C
35768C
66552C
194243901550
WIRING DIAGRAM
This Drawing is merely for illustrating the
components of the electrical system.
30
28
29
DESCRIPTION
Fan Motor
Compressor Serv. Pak
Overload/Relay
Cover-Relay
Heat Exchanger
Cover-Electrical Shield
31
BASIN
PANEL
COLOR
Gray Beige
Almond
Stainless Steel
Sandalwood
Granite
Light Gray
PRINTED IN U.S.A.
ELKAY MANUFACTURING COMPANY 2222 CAMDEN COURT OAK BROOK, IL 60523 630.574.8484
97376C (Rev. C - 10/02)
COLOR TABLE
Item No. 55
Part No.
22706C
22707C
22708C
22709C
22711C
22712C
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.323.0620
PAGE 4
32
NOTE:
WHEN INSTALLING REPLACEMENT
BUBBLER AND PEDESTAL, TIGHTEN
NUT (ITEM 32) ONLY TO HOLD
PARTS SNUG IN POSITION.
DO NOT OVER TIGHTEN.
FIG. 4
Loading...