Elkay E-Granite Installation Instructions Manual
TO BE REMOVED FOR USE BY THE OCCUPANT!
Installation Instructions
E-Granite
™
Sink
• READ THESE INSTRUCTIONS THOROUGHLY BEFORE YOU BEGIN.
• Follow all local plumbing and building codes.
• Before installation, please inspect the sink for damage. Do not install a damaged sink.
• For drop-in sinks proceed to section I. For undermount sinks proceed to section II.
I. DROP-IN INSTALLATION
Note: The clips provided are designed for a maximum countertop thickness of 1-3/4”.
1. To determine the proper size opening for your sink place
the sink upside down on top of the countertop. Mark or trace
line around the edge of the rim. Then cut an opening 5/16”
inside the line. (See illustration A).
2. Set new sink in opening to see that it fits properly.
3. Faucet Holes: Faucet holes can be identified by the faucet
hole emboss on the underside of the faucet deck and the
corresponding circular labels located on the faucet deck top
surface. Before punching the holes please verify that the
circular labels are properly centered over the faucet hole
emboss. The faucet hole should be carefully penetrated
from above the sink using a chisel or screw driver and
tapping lightly on the circular labels. (See illustration B). If
necessary the hole can been enlarged using a metal hole
saw, a jigsaw with a metal cutting blade or a metal file.
Note: MUST SUPPORT FAUCET DECK ON BOTH SIDES
WHILE PUNCHING FAUCET HOLES.
4. Attach faucet, drain fittings and accessories according to the
manufacturer’s instructions.
5. As shown in illustration C and D, align clips with the corre sponding slots in the sinks per illustration C. It may be
necessary to use a mallet and wood block to push it into
place, as shown in illustration D. Make sure metal portion of
the clip (clamp) is in the open position so that sink can be
dropped into cutout.
6. Apply a bead of a high quality silicone adhesive caulk to the
underside of the sink rim and position sink into countertop
opening. CAUTION: Use only a high quality silicone
adhesive caulk.
7. Swing metal portion of clip (clamp) into the clip base. (See
illustration E). Using a Phillips screw driver, turn screw until
clamp engages the countertop. Use shims if necessary.
8. Remove excess caulk and allow caulk to cure following the
caulk manufacturer’s instructions.
DRAW SECOND
LINE INSIDE SINK
OUTLINE (CUT LINE)
TRACE COMPLETELY
AROUND EDGE OF SINK
SLOT
ILLUSTRATION A
CLIP BASE
OPEN
CLAMP
5/16"
ILLUSTRATION B
ILLUSTRATION C ILLUSTRATION D ILLUSTRATION E
SILICONE CAULK
(NOT INCLUDED)
CLOSED
CLAMP
Installation Instructions
II . UNDERMOUNT INSTALLATION
ATTENTION INSTALLER:
•ELKAY RECOMMENDS THAT UNDERMOUNT SINKS SHOULD BE INSTALLED BY A PROFESSIONAL EXPERIENCED
INSTALLER.
• WARNING: THE ENCLOSED CUTOUT TEMPLATE PROVIDES A SINK OPENING THAT WILL EXPOSE APPROXIMATELY
1/8" OF SINK RIM LEDGE AS SHOWN IN ILLUSTRATION F.
• IT IS RECOMMENDED THAT YOU DISCUSS THIS WITH YOUR CUSTOMER AND AGREE TO WHAT THE FINISHED
EFFECT WILL BE. ELKAY IS NOT RESPONSIBLE F
• ELKAY E-GRANITE UNDERMOUNT SINKS MUST BE FASTENED TO SOLID SURFACE COUNTERTOPS ONLY (I.E. GRANITE).
• ELKAY IS NOT RESPONSIBLE FOR SINK AND COUNTERTOP IF DAMAGED DURING INSTALLATION.
• FOLLOW ALL LOCAL PLUMBING AND BUILDING CODES.
1. Position template on countertop. Locate front to rear, so sink
will not interfere with the cabinet.
2. Trace a line around the template. Cut along the inside of
this line to provide opening.
3. Locate and provide for the mounting holes (following
the countertop manufacturer’s instructions). Holes should
allow for even spacing around sink. Type of fasteners to be
as recommended by countertop supplier.
4. Fasten m
U
sing a high quality silicone adhesive caulk, apply a bead
5.
ounting brackets to countertop loosely.
evenly all around the top of the sink flanges.
6. Position and align the sink in the countertop opening.
7. Tighten fasteners until mounting brackets are snug against
sink. (See illustration F).
8.
C
heck alignment of sink to countertop opening.
9. Tighten down fasteners evenly. Be careful not to over-
tighten. Remove excess caulk and allow caulk to cure
following the caulk manufacturer’s instr
C
ARE AND CLEANING GUIDE
E
lkay E-Granite was created for a lifetime of easy care. Just
uctions.
follow the simple guidelines listed below.
Routine Care
M
ost dirt and stains: Wipe with a damp cotton cloth/sponge
and soapy water. Towel dry with a cotton cloth.
It is
recommended that you clean your sink prior to first use.
Stubborn stains and water marks: Wipe with a Mr. Clean®
Magic Eraser® and either water or a 50/50 white vinegar
and water solution. Towel dry with a cotton cloth.
Difficult stains: Use a 3M Scotch-Brite™ Heavy Duty Scour
Pad with either water, 50/50 white vinegar and water solution
or non-abrasive cleaner. Start cleaning in a circular motion
with a constant pressure over the area of the stain, rinse
thoroughly with water and dry with a cotton cloth. Let dry
5-10 minutes. If stain persists, repeat.
OR IMPROPER SINK OR COUNTERTOP INSTALLATIONS.
SILICONE CAULK
(NOT FURNISHED)
COUNTERTOP
MOUNTING CLIP
FASTENER
(NOT FURNISHED)
ILLUSTRATION F
Preventing Damage
• Avoid exposing Elkay E-Granite to strong chemicals, such as
paint removers, oven cleaners, etc. If contact occurs, quickly
flush the surface with water. Do not use straight or undiluted
bleach solution.
• Do not use any abrasive cleaning products, scouring pads or
steel woo
l.
• Do not use caustic solutions containing ammonia or alkalis.
Examples include certain bath and drain cleaner products.
• On a weekly basis, spray e-granite Rejuvenator evenly onto
the clean sink surface. Wipe with soft cloth to uniform sheen.
Let product completely dry on sink surface.
• One e-granite Rejuvenator sample is supplied with each
e-granite sink. For re-order please visit byelkay.com.
COUNTERTOP
REVEAL
APPROX. 1/8”
SINK
Loading...