Pedestal Barrier Free Stone Fountain
INSTALLER
4595_FTN
Owners Manual
Model 4595
T o assure you install your 4595 Stone Fount ain model easily and correctly,
PLEASE READ THESE SIMPLE INSTRUCTIONS BEFORE STARTING THE
INSTALLA TION. CHECK YOUR INST ALLATION FOR COMPLIANCE WITH
PLUMBING, ELECTRICAL, AND OTHER APPLICABLE CODES. After installation,
leave these instructions with the Fountain for future reference.
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON
IMPORTANT! INSTALLER PLEASE NOTE.
THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO WA TER LINES
IS A COMMON PROCEDURE. THIS GROUNDING MA Y BE IN THE BUILDING OR MA Y OCCUR A WA Y FROM THE
BUILDING . THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK INTO A FOUNT AIN, CREA TING AN
ELECTROL YSIS WHICH CAUSES A MET ALLIC T ASTE OR AN INCREASE IN THE MET AL CONTENT OF THE
WA TER. THIS CONDITION IS AVOIDABLE BY USING THE PROPER MA TERIALS AS INDICA TED. ANY DRAIN
FITTINGS PROVIDED BY THE INST ALLER SHOULD BE MADE OF PLASTIC T O ELECTRICALL Y ISOLA TE THE
FOUNT AIN FROM THE BUILDING PLUMBING SYSTEM.
General Installation Tips
1. Water supply 3/8" O.D. unplated copper tube. Waste 1-1/4" IPS. Contractor to supply waste trap and service stop valve
in accordance with local code.
2. Connecting lines to be made of unplated copper and should be thoroughly flushed to remove all foreign matter before
being connected to fountain. This fountain is manufactured in such a manner that it does not in any way cause taste,
odor, color, or sediment problems.
3. Connect fountain to supply line with a shut-off valve and install a 3/8" unplated copper water line between the valve and
the cooler. Remove any burrs from out side of water line. Push the tubes straight into the fittings until they reach a
positive stop, approximately 3/4" (See Fig. 6). DO NOT SOLDER TUBES INSERTED INTO THE STRAINER AS
DAMAGE TO THE O-RINGS MA Y RESUL T.
4. These products are designed to operate on 20 psig to 105 psig supply line pressure. If inlet pressure is above 105 psig,
a pressure regulator must be installed in the supply line. Any damage caused by reason of connecting this product to
supply line pressures lower than 20 psig or higher than 105 psig is not covered by warranty .
Page 1 97460C (Rev. SIB - 6/06)
4595_FTN
FIG. 1
Installation Instructions
1. This fountain is to be mounted on a smooth, flat, finished surface with adequate support structure. NOTE: Mounting
structure must be capable of supporting 300 lb. load on fountain.
2. Refer to rough-in for plumbing.
3. Install shut-off valve on water supply . (V alve not furnished).
4. Locate and install fountain using 3/8" minimum screws or bolts. (Screws or bolts not furnished). CAUTION: This fountain
is rated for inlet water pressure of 20-105 PSI. A pressure reducing regulator should be used if the inlet water supply
exceeds 105 PSI.
5. Connect water supply and fountain drain. Water connection and drain must comply with local codes.
6. Turn on water supply and check all connections for leaks.
Page 297460C (Rev. SIB - 6/06)
See Fig. 3
16
18
4595_FTN
9-A
18
2
9-B
14
6
3
1
BUBBLER DET AIL
2
2
5
6
22
3
2
5
16
22
24
23
11
16
21
16
16
15
12
1
17
24
2023
FIG. 2
8
4
10
STREAM HEIGHT ADJUSTMENT: Stream height is factory set at
35 PSI. If supply pressure varies greatly from this, remove
7
19
13
items 7 and 8 (See Fig. 3) and adjust screw on item 19.
Clockwise adjustment will raise stream and counter-clockwise
adjustment will lower stream. For best adjustment, stream
should hit basin approx. 6-1/2" from bubbler.
FIG. 3 FIG. 4
Page 3 97460C (Rev. SIB - 6/06)
4595_FTN
4595_FTN
ITEM NO.
1
2
3
4
5
6
7
8
9 - A
9 - B
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
P ARTS LIST
P ART NO.
100147140560
100322740560
101570540560
15005C
15013C
170705042830
40048C
40089C
400942308640
98287C
40169C
40250C
45476C
50986C
55913C
55996C
56092C
56121C
600985551640
61313C
66346C
70682C
70683C
75588C
75589C
DESCRIPTION
Drain Gasket
Bubbler Gasket
Drain Gasket
Regulator Retaining Nut
Bubbler Tube Assy.
Basin
Button
Cover Nut
Bubbler
Bubbler Assembly
Hex Nut 1-5/16-20UN
Tailpipe 1-1/4" x 5-3/8"
Drain Tube
Regulator Holder
Drain Adapter
In-Line Strainer
Poly Tubing (Cut To Length)
Drain Elbow 1-1/4"
Drain Plug Assy.
Regulator
Drain Tube
Tee - 1/4
Union - 1/4
Slip Joint Nut 1-1/4"
Gasket
TROUBLE SHOOTING AND MAINTENANCE
Orifice Assy: Mineral deposits on orifice can cause water
flow to spurt or not regulate. Mineral deposits may be
removed from the orifice with a small round file or small
diameter wire. CAUTION: DO NOT file or cut orifice
material.
Stream Regulator: If orifice is clean, regulate flow as in
"STREAM HEIGHT ADJUSTMENT" instructions on page
3. If replacement is necessary , see part s list for correct
regulator part number .
Actuation of Quick Connect Water Fittings: Fountain is
provided with lead-free connectors which utilize an o-ring
water seal. T o remove tubing from the fitting, relieve water
pressure, push in on the gray collar while pulling on the
tubing (See Fig. 5). To insert tubing, push tube straight
into fitting until it reaches a positive stop, approximately
3/4".
PRINTED IN U.S.A.
FIG. 5
1/4" O.D. TUBE
WATER INLET
TO FOUNTAIN
3/8" O.D. UNPLATED
COPPER TUBE CONNECT
COLD WA TER SUPPL Y
NOTE: WA TER FLOW
DIRECTION
BUILDING WATER INLET
SERVICE STOP
(NOT FURNISHED)
FIG. 6
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.323.0620
Page 497460C (Rev. SIB - 6/06)
Loading...