4420DB_FTN_A LK4420DB_FTN_A
Owners Manual
Model 4420DB
Bi-Level Tubular Fountain with Pet Fountain
INSTALLER
4420DB Fountains are among the easiest to install Fountains on the market today.
To assure you install these models easily and correctly, PLEASE READ THESE
SIMPLE INSTRUCTIONS BEFORE STARTING THE INSTALLATION. CHECK YOUR
INSTALLATION FOR COMPLIANCE WITH PLUMBING, ELECTRICAL, AND OTHER
APPLICABLE CODES. After installation, leave these instructions with the Fountain for
future reference.
PAGE 1 1000003946 (Rev. A - 06/17)
4420DB_FTN_A LK4420DB_FTN_A
INSTALLATION INSTRUCTIONS
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON
IMPORTANT! INSTALLER PLEASE NOTE.
THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO WATER LINES
IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY OCCUR AWAY FROM THE
BUILDING. THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK INTO A FOUNTAIN, CREATING AN
ELECTROLYSIS WHICH CAUSES A METALLIC TASTE OR AN INCREASE IN THE METAL CONTENT OF THE
WATER. THIS CONDITION IS AVOIDABLE BY USING THE PROPER MATERIALS AS INDICATED. ANY DRAIN
FITTINGS PROVIDED BY THE INSTALLER SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISOLATE THE
FOUNTAIN FROM THE BUILDING PLUMBING SYSTEM.
1. This fountain is to be mounted on a smooth, at, nished surface with adequate support structure. NOTE: Mounting
structure must be capable of supporting 300 lb. load on fountain.
2. Refer to rough-in for plumbing.
3. Install shut-off valve on water supply. (Valve not furnished)
4. Locate and install fountain using 3/8" minimum fasteners. (Fasteners not furnished)
5. Connect water supply and fountain drain. Connect drain waste "Tee" to fountain drain tubes. Connect outlet of "Tee" to
drainage system. Water connection and drain must comply with local codes.
6. Turn on water supply and check all connections for leaks.
CAUTION: This fountain is rated for inlet water pressure of 20-105 PSI. A pressure reducing regulator should be used if the
inlet water supply exceeds 105 PSI. Any damage caused by reason of connecting this product to supply line
pressures lower than 20 PSI or higher than 105 PSI is not covered by warranty.
7. Water supply 3/8" O.D. unplated copper tube. Waste 1-1/2" IPS. Contractor to supply waste trap and service stop valve in
accordance with local code.
8. Connecting lines to be made of unplated copper and should be thoroughly ushed to remove all foreign matter before being
connected to fountain. This fountain is manufactured in such a manner that it does not in any way cause taste, odor, color,
or sediment problems.
9. Connect fountain to supply line with a shut-off valve and install a 3/8" unplated copper water line between the valve and the
fountain. Remove any burrs from outside of water line. Push the tubes straight into the ttings until they reach a positive
stop, approximately 3/4" (See Fig. 2). DO NOT SOLDER TUBES INSERTED INTO THE STRAINER AS DAMAGE TO THE
O-RINGS MAY RESULT.
PAGE 21000003946 (Rev. A - 06/17)
4420DB_FTN_A LK4420DB_FTN_A
254mm
10"
O
10"
254mm
O
* ADA REQUIREMENT
878mm
34 9/16"
HEIGHT
ORIFACE
850mm
33 7/16"
*
689mm
27 1/8"
C
mm
L)
1/2"13
P
(8
O
)
14"
356mm
PL
(2
O
29"
737mm
19"
483mm
A
1-1/2" DRAIN
FINISHED FLOOR
0mm
26"
.
B.C
(2 PL)
12"
305mm
O
66
HEIGHT
1053mm
41 7/16"
ORIFACE
54mm
10"
2
O
B
PAGE 3 1000003946 (Rev. A - 06/17)
1025mm
40 5/16"
8"
203mm
B
6 9/16"
167mm
LEGEND
A = 3/8" O.D. UNPLATED COPPER TUBE CONNECT - SHUT OFF VALVE BY OTHERS
B = ACCESS PANEL ( 8" X 10" )
30"
762mm
C = REMOVABLE BOTTOM COVER
4420DB_FTN_A LK4420DB_FTN_A
3
7
9
3
1
3
16
18
8
7
9
5
3
7
4
2
10
11
18
13
19
6
10
See Fig. 3
See Fig. 3
12
17
15
14
6
PAGE 41000003946 (Rev. A - 06/17)
4420DB_FTN_A LK4420DB_FTN_A
TROUBLE SHOOTING AND MAINTENANCE
ACTUATION OF QUICK CONNECT WATER FITTINGS:
Fountain is provided with lead-free connectors which utilize an
o-ring water seal. To remove tubing from the tting, relieve water
pressure, push in on the gray collar while pulling on the tubing. (see
Fig.2) To insert tubing, push tube straight into tting until it reaches
a positive stop, approximately 3/4".
1/4" O.D. TUBE
WATER INLET
TO COOLER
FIG. 1
OPERATION OF QUICK CONNECT FITTINGS
OPERATION OF QUICK CONNECT FITTINGS
SIMPLY PUSH IN
SIMPLY PUSH IN
TUBE TO ATTACH
TUBE TO ATTACH
A B C
3/8" O.D. UNPLATED COPPER TUBE CONNECT
COLD WATER SUPPLY
NOTE: WATER FLOW
DIRECTION
TUBE IS SECURED
TUBE IS SECURED
IN POSITION
IN POSITION
B CA
BUILDING WATER INLET
SERVICE STOP
(NOT FURNISHED)
PUSH IN COLLET
PUSH IN COLLET
TO RELEASE TUBE
TO RELEASE TUBE
PUSHING TUBE IN BEFORE
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
PULLING IT OUT HELPS TO
RELEASE TUBE
RELEASE TUBE
FIG. 2
9
BASIN
Vandal-Resistant Bubbler
FIG. 3
*FINISH COLOR OPTIONS – Choose color option to
complete your model number, add as sufx example:
4420DBEVG
Matte nish: Evergreen = EVG
Gloss nish:
Beige = BGE Gray = GRY Terracotta = TER
Black = BLK Orange = ORN White = WHT
Blue = BLU Purple = PUR Yellow = YLW
Brown = BRN Red = RED
FIG. 4
STREAM HEIGHT ADJUSTMENT:
Stream height is factory set at 35 PSI. If supply pressure
varies greatly from this, insert a small straight bladed
screwdriver through the access hole in the center of the
push button and turn the adjustment screw. Clockwise
adjustment will raise the stream and counterclockwise
adjustment will lower the stream. For best adjustment,
the stream should be approximately 1 1/2" above the
top of the bubbler . (See Fig. 4)
ITEMIZED PARTS LIST
ITEM
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
NS
NS
NS = Not Shown
*select color option to complete part number
PART NO.
98683C
98682C
1000003694
1000003695
0000000325
98530C
45726C
97247C
28467C
40551C
97446C
0000000466
101570540560
1000003812*
1000003813*
45926C
70852C
66346C
55996C
98684C
45724C
1000003490
56092C
DESCRIPTION
Kit - Drain Adapter/Gasket/Nut/Washer
Kit - Push Button w/Blank Nameplate
Kit - Push Button w/LK4420DB Nameplate
Kit - Push Button w/4420DB Nameplate
Kit - Drain Plug & Gasket
Kit - Regulator/Holder/Nut
Plug - Drain
Kit - VR Torx Screws/Bit
Basin
Tailpipe
Kit-Bubbler (VR)
Kit - Bubbler (Dog Bowl)
Gasket
Access Panel
Bottom Cover
Drain Tube
Tee - 3/8"
Drain Tube
In - Line Strainer
Kit - Drain Elbow/Nut/Washer/Gasket
Tailpipe - 10" Lg.
Tube - Drain
Tubing-1/4" Poly (Cut To Length)
PRINTED IN U.S.A.
Halsey Taylor – halseytaylor.com
Elkay – elkay.com
FOR PARTS CONTACT YOUR LOCAL DISTRIBUTOR OR CALL TECHNICAL SERVICES AT 1.800.834.4816
2222 CAMDEN COURT, OAK BROOK, ILLINOIS 60523
PAGE 5 1000003946 (Rev. A - 06/17)
Loading...