Elkay 4420BF1LDB Installation Manual

4420BFDB FOUNT AIN

Owners Manual

Model 4420BFDB

Bi-Level Tubular Bottle Filler Fountain w/Dog Bowl

4420BF1LDB

4420BF2DB

4420BF1UDB

INSTALLER

4420BFDB Fountains are among the easiest to install Fountains on the market today.
To assure you install these models easily and correctly, PLEASE READ THESE
SIMPLE INSTRUCTIONS BEFORE STARTING THEINSTALLATION. CHECK YOUR
INSTALLATION FOR COMPLIANCE WITH PLUMBING, ELECTRICAL, AND OTHER
APPLICABLE CODES. After installation, leave these instructions with the Fountain
for future reference.

IMPORTANT

ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON

IMPORTANT! INSTALLER PLEASE NOTE.

THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO WA TER LINES
IS A COMMON PROCEDURE. THIS GROUNDING MA Y BE IN THE BUILDING OR MA Y OCCUR A WA Y FROM THE
BUILDING . THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK INTO A FOUNT AIN, CREA TING AN ELEC­TROL YSIS WHICH CAUSES A MET ALLIC T ASTE OR AN INCREASE IN THE METAL CONTENT OF THE WA TER.
THIS CONDITION IS A VOIDABLE BY USING THE PROPER MA TERIALS AS INDICA TED. ANY DRAIN FITTINGS
PROVIDED BY THE INST ALLER SHOULD BE MADE OF PLASTIC T O ELECTRICALLY ISOLA TE THE FOUNT AIN
FROM THE BUILDING PLUMBING SYSTEM.

PAGE 1 98645C (Rev. B - 3/11)

4420BFDB FOUNT AIN

3"

76mm

4420BF1LDB

10"

254mm

O

57"

1448mm

37"

14 9/16"

371mm

940mm

27"

686mm

C

1/2"

14"

356mm

O

13mm

(2 PL)

(10 PL)

O

29"

737mm

10"

254mm

19"

483mm

A

1-1/2" DR AIN

FINISHED FLOOR

O

26"

660mm

B.C.

12"

305mm

(2 PL)

40 5/16"

1025mm

HEIGHT

42 3/16"

1072mm

ORIFICE

8"

203mm

O

10"

254mm

O

B

B

6 9/16"

167mm

30"

762mm

LEGEND

A = 3/8" O.D. UNPLA TED COPPER TUBE CONNECT - SHUT OFF V AL VE BY OTHERS

B = ACCESS P ANEL ( 8" X 10" )

C = REMOV ABLE BOTTOM COVER

PAGE 298645C (Rev. B - 3/11)

4420BFDB FOUNT AIN

3"

76mm

4420BF1UDB

10"

254mm

O

35 3/16"

894mm

HEIGHT

ORIFICE

33 5/16"

847mm

27"

686mm

C

10"

254mm

1/2"

14"

356mm

O

13mm

(10 PL)

O

(2 PL)

29"

737mm

26"

12"

660mm

B.C.

305mm

O

(2 PL)

10"

254mm

14 9/16"

371mm

O

19"

483mm

A

1-1/2" DRAIN

44"

1118mm

64"

1626mm

FINISHED FLOOR

8"

203mm

O

B

B

6 9/16"

167mm

30"

762mm

LEGEND

A = 3/8" O.D. UNPLA TED COPPER TUBE CONNECT - SHUT OFF V AL VE BY OTHERS

B = ACCESS P ANEL ( 8" X 10" )

C = REMOV ABLE BOTTOM COVER

PAGE 3 98645C (Rev. B - 3/11)

4420BFDB FOUNT AIN

4420BF2DB

10"

254mm

O

10"

254mm

O

57"

1448mm

37"

14 9/16"

371mm

3"

76mm

940mm

27"

686mm

C

10"

254mm

1/2"

13mm

14"

(10 PL)

356mm

(2 PL)

O

O

29"

737mm

26"

660mm

B.C.

12"

305mm

(2 PL)

O

19"

483mm

A

14 9/16"

371mm

64"

1626mm

3"

76mm

44"

1118mm

1-1/2" DRAIN

FINISHED FLOOR

8"

203mm

O

B

B

6 9/16"

167mm

30"

762mm

LEGEND

A = 3/8" O.D. UNPLA TED COPPER TUBE CONNECT - SHUT OFF V AL VE BY OTHERS

B = ACCESS P ANEL ( 8" X 10" )

C = REMOV ABLE BOTTOM COVER

PAGE 498645C (Rev. B - 3/11)

4420BFDB FOUNT AIN

1. This fountain is to be mounted on a smooth, flat, finished surface with adequate support structure. NOTE: Mounting structure must be
capable of supporting 300 lb. load on fountain.

2. Refer to rough-in for plumbing.

3. Install shut-off valve on water supply . (V alve not furnished)

4. Locate and install fountain using 3/8" minimum screws or bolts. (Screws or bolts not furnished)

5. Prior to installing the bottle filler to the center mounting position of fountain, insert the drain pipe (Item #15) by positioning the short
end of drain pipe through mounting plate of bottle filler. Inst all bottle filler to fountain and secure with supplied hardware.

6. Prior to installing the bottle filler to the arm mount of fountain, insert the drain pipe (Item #14) into the arm tunnel and adjust drain to
lean to the left side of the armwhen facing the button. Install bottle filler to arm being sure drain tube is above mounting plate of filler .
Install filler to fountain and secure with supplied hardware.

7. Connect water supply and fountain drain. Connect drain waste "T ee" to fountain drain tubes. Connect outlet of "T ee" to drainage
system. Water connection and drain must comply with local codes.

8. Turn on water supply and check all connections for leaks.
CAUTION: This fountain is rated for inlet water pressure of 20-105 PSI. A pressure reducing regulator should be used if the inlet water

supply exceeds 105 PSI. Any damage caused by reason of connecting this product to supply line pressures lower than 20

9. Water supply 3/8" O.D. unplated copper tube. Waste 1-1/4" IPS. Contractor to supply waste trap and service stop valve in
accordance with local code.

10. Connecting lines to be made of unplated copper and should be thoroughly flushed to remove all foreign matter before being con
nected to fountain. This fountain is manufactured in such a manner that it does not in any way cause taste, odor , color , or sediment
problems.

1 1. Connect fountain to supply line with a shut-off valve and install a 3/8" unplated copper water line between the valve and the cooler .
Remove any burrs from outside of water line. Push the tubes straight into the fittings until they reach a positive stop, approximately
3/4" (See Fig. 2). DO NOT SOLDER TUBES INSERTED INTO PLASTIC FITTINGS AS DAMAGE TO THE O-RINGS MAY
RESULT.

TROUBLE SHOOTING AND MAINTENANCE

Actuation of Quick Connect Water Fittings:

Fountain is provided with lead-free connectors which utilize an
o-ring water seal. T o remove tubing from the fitting, relieve water
pressure, push in on the gray collar while pulling on the
tubing.(see Fig.2) To insert tubing, push tube straight into fitting
until it reaches a positive stop, approximately 3/4".

FIG. 2

FIG. 3

1/4" O.D. TUBE
WATER INLET
TO COOLER

FIG. 1

3/8" O.D. UNPLATED
COPPER TUBE CONNECT
COLD WA TER SUPPLY

NOTE: WA TER FLOW

DIRECTION

BUILDING WATER INLET

SERVICE STOP
(NOT FURNISHED)

STREAM HEIGHT ADJUSTMENT :

Stream height is factory set at 35 PSI. If supply
pressure varies greatly from this, insert a small straight
bladed screwdriver through the access hole in the
center of the push button and turn the adjustment
screw. Clockwise adjustment will raise the stream and
counterclockwise adjustment will lower the stream. For
best adjustment, the stream should be approximately
1 1/2" above the top of the bubbler . (See Fig. 3)

PAGE 5 98645C (Rev. B - 3/11)

27

4420BFDB FOUNT AIN

18 & 28

23 & 27

22 & 29

27

28

28

25

2

28

19 & 28

21

30

19

23

16

4

1

ARM ONL Y 14

FIG. 4

16

28

19

15

19

25

28

4

16

3

1

19
28
17 OR 20

19

20

9

10

1

19

28

5

9

19

26

8

26

6

27

PAGE 698645C (Rev. B - 3/11)

ITEMIZED P ARTS LIST

ITEM NO. PART NO.

1
2
3
4
5
6
7
8

9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30

28467C
28955C
40551C
45464C
45832C
45833C
45476C
45724C
45726C
45727C
45926C
55996C
66346C
66816C
66815C
98118C
98530C
98532C
98677C
98678C
98679C
98680C
98681C
98682C
98683C
98684C
98685C
98686C
P05031
45931C

4420BFDB FOUNT AIN

DESCRIPTION

Basin
Cover - Round Plate
Tailpipe
Drain Plug 1-1/2"
Access Panel
Bottom Cover
Drain Tube (Not Shown)
Tailpipe - 1-1/4" x 10"Lg.
Drain Plug 1-1/2" (Dog Bowl)
Body - Bubbler (Dog Bowl)
Drain Tube - 1-1/2" x 27-1/2" Lg.
In - Line Strainer
Drain Tube
Tube - Drain (Arm Only)
Tube - Drain
Bubbler Assembly
Kit - Regulator W/Spring
Kit - "O" Rings and Fittings
Kit - Gasket
Kit - 1.0 GPM Regulator (BF Only)
Kit - Nozzle
Kit - Aerator
Kit - Bottle Filler Trim
Kit - Push Button
Kit - Plastic Drain
Kit - 90° Plastic Drain
Kit - 4400 Series Hardware
Kit - Bottle Filler Waterway
Aerator
Outdoor Bottle Filler Drain Plug

PRINTED IN U.S.A.

See Fig. 4

5

12

27

10

FOR PARTS CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.260.6640

5

PAGE 7 98645C (Rev. B - 3/11)

11

4420BFDB FOUNT AIN

THIS P AGE W AS LEFT INTENTIONALL Y BLANK

PAGE 898645C (Rev. B - 3/11)