ELK M1GOLD User Manual
ELK-SWB14
ELKELK
ELK
ELKELK
PRODUCTS, INC.
The ELK-SWB14 is a universal structured wiring box featuring a pattern of hole-slot-hole that allows it to accommodate accessories,
circuit boards, shelves, brackets, and wiring modules from many different manufacturers. It is designed to be surface mounted but
can also be flush mounted with the addition of an optional ELK-SWFD14 Flush Mount Door.
14” STRUCTURED WIRING BOX
1. Remove any conduit knockouts prior to mounting the box.
Only these two (2) knockouts may be used if an M1 Control is installed!
These two (2) knockouts CANNOT be
used if an M1 Control is installed.
2. Position the box against the wall making sure that it is level. Install a
#10 screw (not included) in the upper left and right key shaped
mounting holes. Make any adjustments to the box level and then
install two more screws in the lower 2 mounting holes.
3. Pull wires through one or more of the entry holes. The design of the
SWB14 allows wires to be organized along the sides. Plastic wire
ties can be used to secure wiring.
4 If desired, a one gang electrical “J” box and duplex outlet may be
mounted in the large rectangular knockout of the lower flange. Use
#6 Flat Head Self-Tapping Screws (not included).
5. For accessory circuit boards there are 8 columns of repeated 2-hole
punch patterns. These are labeled A, B, D, E, F, H, J, & K on the box
diagram. One hole in each pattern is slightly larger than the other.
These 2-hole patterns are for plastic Circuit Board Glides (p/n ELKSWG). The small hole is for a 6/32 type “F” mounting screw and the
large hole is for a half-moon shape ltab on the bottom of each glide.
E
L
K
-
S
W
G
To mount a circuit board, select a pair of 2-hole patterns in the same
vertical column that have their larger holes facing one another. The
distance between the center of the large holes determines the size
(length) of the circuit board that may be mounted. The available
mounting lengths in inches are: 3-1/2”, 4”, 6”, 8”, 9-3/8”, and 11”.
Starting at the top, loosely start a 6/32” mounting screw in the small
hole of the first selected 2-hole pattern. Place the slotted edge of a
circuit board glide under this screw, making sure that the half-moon
tab fits into the larger hole and the grooved edge is facing down.
Tighten the screw using a long shafted screwdriver. In the second
or lower 2-hole pattern loosely start a 6/32” mounting screw.
Attach the second circuit board glide using the same procedures.
The grooved edge of this glide should face up.
L531 01/07
ABCD FGHJ K
E
M1 Control Mounting Area
PO Box 100 • Hildebran, NC 28637 • 828-397-4200 • 828-397-4415 FAX
http://www.elkproducts.com • email: info@elkproducts.com
I
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
ELK PRODUCTS, INC.
The circuit board should slide freely into the grooves between the
two glides. If the board is loose or too tight, simply loosen one of
the mounting screws and adjust the glide to assure a good fit.
Optional Accessories For SWB14
ELK-SWFD14 Flush Mount Hinged Door
ELK-SWD1 1.75” Gromment Donuts (2)
ELK-SWG Circuit Board Glides (2)
ELK-SWNS1 Nylon Standoffs for SWP (10)
ELK-SWP 4.5” Multipurpose Adapter Plate
ELK-SWP3 3” Multipurpose Adapter Plate
ELK-SWS Battery Shelf
PRINTED IN USA
Loading...