The information in this document is subject to change without prior notice in order to
improve reliability, design and function and does not represent a commitment on the part
of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are
reserved. No part of this manual may be reproduced by any mechanical, electronic, or
other means in any form without prior written permission of the manufacturer.
Trademarks
Phoenix is a trademark of Phoenix BIOS Corporation. AutoCAD and Autoshade are
trademarks of Autodesk, Inc. IBM, OS/2, and VGA are trademarks of International
Business Machines Corp. Lotus, 1-2-3, and Symphony are trademarks of Lotus
Development Corp. Windows, Word, MS-DOS, and Microsoft are trademarks of
Microsoft Corp. VESA is a trademark of Video Electronics Standards Association.
Other product names mentioned herein are used for identification purposes only and may
be trademarks and/or registered trademarks of their respective companies.
Limitation of Liability
While reasonable efforts have been made to ensure the accuracy of this manual, the
manufacturer and distributor assume no liability resulting from errors or omissions in this
manual, or from the use of the information contained herein.
Page 4
Notices
Federal Communications Commission Radio Frequency Interference
Statement
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and if not installed and used in accordance with the
instruction manual may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio TV technician for help.
ii
Notice:
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Page 5
Shielded interface cables and a non-shielded AC power cord must be used in order to
comply with emission limits.
This equipment is to be used with power supply:
I/P: 100-240 Vac, 50-60Hz, 1.5A
O/P: 19Vdc, 4.74A
There is no internal power supply.
Canadian DOC Notice For Class B Computing Devices
This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations.
Cet appareil numerique de la classe B repecte toutes les exigences du Règlement sur le
matèriel brouilleur du Canada.
Safety Precautions
This section is designed to assist you in identifying potentially unsafe conditions while
working with this product. Required safety features have been installed in the computer
to protect you from injury. However, you should use good judgment to identify potential
safety hazards:
1.
Please read these safety instructions carefully.
2.
Please keep this User's Manual for later reference.
3.
Please disconnect this equipment from AC outlet before cleaning. Don't use liquid
or sprayed detergent for cleaning. Use moisture sheet or cloth for cleaning.
4.
For pluggable equipment, that the socket-outlet shall be installed near the
equipment and shall be easily accessible.
5.
Please keep this equipment from humidity.
6.
Lay this equipment on a reliable surface when installed. A drop or fall could cause
injury.
7.
Make sure to use the right voltage for the power source when connecting the
equipment to the power outlet.
iii
Page 6
8.
Place the power cord in such a way that people can not step on it. Do not place
anything on top of the power cord.
9.
All cautions and warnings on the equipment should be noted.
10.
If the equipment is not use for a long time, disconnect the equipment from the main
power outlet to avoid being damaged by transient overvoltage.
11.
Never pour any liquid into the opening, this could cause fire or electrical shock.
12.
Never open the equipment. For safety reason, the equipment should only be opened
by a qualified service personnel.
13.
If on the following situations arises, get the equipment checked by a service
personnel:
a.
The Power cord or plug is damaged.
b.
Liquid has penetrated into the equipment.
c.
The equipment has been exposed to moisture.
d.
The equipment has not work well or you cannot get it work according to the user's
manual.
e.
The equipment has dropped and damaged.
f.
If the equipment has obvious sign of breakage.
14.
Do not leave this equipment in an environment unconditioned, storage temperature
above 60°C (140°f), it may damage the equipment.
iv
15.
The unit can be operated at an ambient temperature of max. 35°C.
16.
The sound pressure level at the operators position according to IEC 704-1: 1982 is
equal or less than 70 dB(A).
17.
Power Cord Requirements
The power cord set used with the AC adaptor must meet the requirements of the
country where you use the AC adaptor, whether it is 100-120 or 200-240 Vac. The
following information explains the requirements for power cord set selection.
• The cord set must be approved for the country in which it is used.
• The appliance coupler must have a configuration for mating with a
CEE22/EN6032/IEC 320 appliance inlet.
Page 7
A.
For U.S. and Canada:
• The cord set must be UL Listed and CSA Certified.
• The minimum specifications for the flexible cord are No. 18 AWG.
B.
For Japan:
• All components of the cord set must bear a “ T ” mark and registration
number in accordance with the Japanese Dentori Law.
• The minimum specifications for the flexible cord are .75m ㎡
conductors.
C.
For Other Countries:
• The cord set fittings must bear the certification mark of the agency
responsible for evaluation in a specific country.
• The flexible cord must be of a HAR (harmonized) type H05VV-F.
• The cord set must have a current capacity of a least 2.5 Amperes and
voltage rating of 125 or 250 Vac.
18.
When using your telephone equipment, basic safety precautions should always be
followed to reduce the risk of fire, electric shock and injury to persons. These
precautions includes the following:
1. Do not use this product near water, for example, near a bathtub, washbowl,
kitchen sink or laundry tub, in a wet basement or near a swimming pool.
2. Avoid using a telephone (other than a cordless type) during an electrical
storm. There may be a remote risk of electric shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord indicated in this manual.
19.
Do not use the AC adapter near open water or other liquids. Never spill liquid into
the AC adapter.
20.
Laser Warning: Laser Class I Product Caution - Invisible laser radiation when open
avoid exposure to beam.
21.
Danger of explosion if battery is incorrectly replaced. Replace only with the same
v
Page 8
or equivalent type recommended by the manufacturer. Dispose of used batteries
according to the manufacturer's instructions. Never remove the battery pack while
the power is on as this may result in data loss when the system loses power.
Wichtige Sicherheitshinweise
1.
Bitte lesen Sie diese Hinweis sorgfältig durch.
2.
Heben Sie dirse Anleitung für den späteren Gebrauch auf.
3.
Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Versenden Sie Keine
Flüssig- oder Aerosolreiniger. Am besten eignet sich ein angefeuchtetes Tuch zur
Reinigung.
4.
Die Netzanschluβsteckdose soll nahe dem Gerät angebracht und leicht zugänglich
sein.
5.
Das Gerät ist vor Feuchtigkeit zu schützen.
6.
Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen oder
Fallen könnte Beschädigungen hervorrufen.
7.
Beachten Sie beim Anschluß an das Stromnet die Anschlußwerte.
8.
Verlegen Sie die Netzanschlußleitung so, daß niemand darüber fallen kann. Es
sollte auch nichts auf der Leitun abgestellt werden.
9.
Alle Hinweise und Warnungen, die sich am Gerät befinden, sind zu beachten.
10.
Wird das Gerät üeinen längeren Zeitraum nicht benutzt, sollten Sie es vom
Stromnetz trennen. Somit wird im Falle einer Überspannung eine Beschädigung
vermieden.
11.
Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüssigkeien in das
Gerät gelangen. Dies könne einen Brand bzw. Elektrischen Schlag auslösen.
12.
Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen
Sicherheit nur von authorisiertem Servicepersonal geöffnet werden.
13.
Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen und
von einer qualifizierten Servicestelle zu Überprüfung.:
vi
a.
Netzlabel oder Netzstecker sind beschädigt.
Page 9
b.
Flüssigkeit ist in das Gerät eingedrungen.
c.
Das Gerät war Feuchtigkeit ausgesetzt.
d.
Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioniert oder Sie
mit Hilfe dieser Anleitung keine Verbesserung erzielen.
e.
Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.
f.
Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.
14.
VORSICHT: Explosiongsgetahr bei unsachgemäßen Austausch der Batterie.
Ersatz nur durch denselben oder einem vom Hersteller empfohlenem ähnlichen Typ.
Entsorgung gebrauchter Batterien nach Angaben des Herstellers.
15.
Dieses Schaltnetzteil kann bis zu einer Außentemperatur von maximal 35ºC.
16.
Die Ausgangswerte dürfen nicht die auf dem Label angegebenen Werte
überschreiten.
17.
Anforderungen an das Stromkabel
Das Kabel-Set, das an das Netzteil angeschlossen wird, muss den Anforderungen
des Landes, in dem Sie das Netzteil einsetzen, genügen, je nachdem, ob die
Netzspannung 100-120 oder 200-240V Wechselspannung beträgt.
• Das Kabel-Set muss für das Land, in dem es eingesetzt wird, zugelassen
sein.
• Der Gerätestecker des Kabels muss in eine CEE22/ EN603/ IEC 320
Buchse passen.
A.
Für die USA und Kanada:
• Das Kabel-Set muss UL-gelistet und CSA zertifiziert sein.
• Die Minimalanforderungen für das Kabel entsprechen No. 18 AWG.
B.
Für Japan:
• Alle Teile des Kabel-Sets müssen entsprechend dem japanischen
Dentori Law mit einem “T”-Symbol markiert sein
• Die Minimalanforderungen für das Kabel sind .75m ㎡ Leiter.
vii
Page 10
C.
Für andere Länder:
• Die Zubehörteile des Kabel-Sets müssen das Prüfsiegel derjenigen
Stelle, die in dem jeweiligen Land für die Sicherheitsprüfung zuständig
ist, tragen.
• Das Kabel muss vom HAR (harmonisierten) Typ H05VV-F sein.
• Das Kabel-Set muss eine Stromkapazität von mindestens 2,5 Ampere
haben und Spannungen von 125 oder 250 V Wechselstrom gestatten.
18.
Bei der Benutzung Ihres Telefongerätes sollten Sie immer die grundlegenden
Sicherheitsmaßnahmen beachten, um das Risiko von Feuer, Stromschlägen und
Verletzungen zu minimieren. Zu beachten sind u.a. folgende Punkte:
1. Benutzen Sie das Gerät nicht in der Nähe von Wasser, wie zum Beispiel
Badewanne, Waschbecken, Spülbecken, Waschbottich, in feuchten
Kellerräumen oder in der Nähe von Schwimmbecken.
2. Benutzen Sie kein Telefon (ausgenommen schnurlose Modelle) während
eines Gewitters. Es besteht das geringe Restrisiko eines Blitzschlages.
3. Benutzen Sie das Telefon nicht um ein Gasleck zu melden, falls es sich in
der Nähe des Lecks befindet.
4. Benutzen Sie nur solch ein Stromkabel, wie in dieser Anleitung
beschrieben.
19.
Benutzen Sie das Netzteil nicht in unmittelbarer Nähe zu Wasser oder anderen
Flüssigkeiten. Gießen Sie nie Flüssigkeiten über das Netzteil.
20.
Achtung Laser: Laser Produkt der Klasse I. Achtung - Unsichtbarer Laserstrahl,
vermeiden Sie Kontakt mit dem Strahl bei offenem Gehäuse.
21.
Es besteht Explosionsgefahr, wenn der Akku nicht ordnungsgemäß ersetzt wird.
Ersetzen Sie den Akku nur durch einen Akku gleichen oder äquivalenten Typs, der
vom Hersteller empfohlen wird. Entsorgen Sie Akkus entsprechend den
Anweisungen des Herstellers. Entfernen Sie den Akku auf keinen Fall bei
eingeschaltetem Notebook, da hierdurch Daten verloren gehen könnten.
Personal Inventory
viii
Page 11
This Notebook computer system is designed for years of productive and pleasurable
computing. Use this section to keep notes about details of your purchase. Update this
section when you add new options.
Date of Purchase:
Dealer’s Name:
Phone:
Address:
E-Mail Address:
WWW Site:
Serial Number:
CPU Type:
Hard Disk Capacity:
Memory Capacity:
Optional Equipment:
ix
Page 12
Page 13
1
Introduction
Page 14
WARNING:
There are more and more people spending large amounts of time in
front of computer monitors now that scientists from many fields
including anatomy, psychology, and occupational safety are involved in
the study of ergonomically sound work environments.
A few tips to help you work effectively without a lot of physical discomfort:
• Purchase a chair with armrests and good back support. Don't slouch when sitting; keep
your back straight.
• Try to place the LCD panel or external monitor so that there is little glare from the sun
on the monitor.
• Walk around the room every hour.
• Every half hour look away from the computer screen for a few minutes.
• Place everything that you need to work within easy reach.
Welcome to the Notebook PC
Congratulations on your purchase of the Notebook PC. Your Notebook features the latest
advances in portable computing technology. The Notebook’s modular design provides
maximum expandability without compromising portability. The high-performance CPU
and enhanced IDE hard drive provides you with extra processing power for handling
complex graphics and running large programs.
2
One PCMCIA slot gives you the ability to use standard PCMCIA cards, such as a LAN
adapter or memory cards.
Page 15
Getting to Know Your Computer
Opening the LCD Panel
At the front of the Notebook you will find a retaining latch on the display panel that locks
the display in closed position when the Notebook is not in use.
1.
Slide the display panel latch to the right until the display panel releases, and then
raise the LCD screen.
2.
At any time you can tilt the display toward or away from you to a comfortable
viewing position.
CAUTION:
1. Try not to slam the display upon closing it.
2. Try not to place any object on top when it is closed or open.
3. Be sure the system is turned off or in suspend mode before you close the
display panel.
With the LCD screen open, you will see several features important for operating your
Notebook computer.
Each of these features is briefly described below:
To avoid damage to the display panel:
3
Page 16
4
1. LCD Cover Release Latch
Slide this latch to the right to open the LCD cover.
Page 17
2. LCD Screen
Your Notebook computer is equipped with a replaceable color Liquid Crystal Display
(LCD) screen that supports up to 1024 x 768 or 1400 x 1050 x 16M LCD resolution
utilizing a AGP BUS.
A built-in backlight allows you to comfortably view the screen even when ambient
lighting is low.
3.
Short-cut Keys
These two short-cut keys are assigned as functions for: Explorer and mail respectively.
4.
Power/Resume Button
Pressing this button for 1-2 seconds will turn on the system or pressing this button
when the computer is in Suspend mode will resume normal operation. Pressing this
button for 4-6 seconds will also turn off the system.
5.
Keyboard
Your computer has an 88-key enhanced keyboard that provides all the functions of a
standard 101/102 key keyboard.
6.
TouchPad
The TouchPad is hardware-compatible with the IBM PS/2 mouse and softwarecompatible with the Microsoft mouse.
7.
TouchPad Buttons
The buttons below the TouchPad correspond to the left and right buttons on a standard
mouse. The PS/2 compatible mouse will work with the Notebook PC’s TouchPad
simultaneously.
8.
Stereo Speakers
The internal speakers provide true stereo sound.
5
Page 18
9. The Built-in Microphone
The built-in microphone is located to the left of the TouchPad.
10.
Scroll Button
Use this button to scroll up and down the scrolling bar.
11.
System Status Indicator Panel
The system status indicator panel keeps you informed of the computer’s operating
status. There are also two system status indicators — Power and Charge LED — on
the left side of the notebook. (Please refer to "The Left Side" section description)
Indicates the the computer is accessing the PCMCIA drive.
Indicates that the computer is accessing the DVD-ROM drive.
Indicates that the computer is accessing the hard disk drive.
Indicates that the keyboard is in Num Lock mode.
Indicates when the keyboard is in Caps Lock mode. In this mode, the
keyboard produces uppercase text when you press a key. When you
press the Caps Lock key again, the indicator goes off and the
keyboard produces lowercase text.
Indicates when the keyboard is in Scroll Lock mode. Some
applications will move information across the screen differently when
Scroll Lock is on.
6
Page 19
The Front
NOTE: This application does not apply when the system is power on.
The function of this application is the same as when you are using the Windows
based Media Player in playing a music CD.
1.
The Play/Pause Button
Press the Play button to play a selected track. Press the Pause button to freeze the
music when necessary. Pressing the button again resumes playing the track from
where it was frozen.
2.
The Stop/Eject Button
Press this button to stop a track. If you then press the Play button or the button of the
stopped track, the track restarts from its very beginning.
Press this button to open the disc tray. The button then changes to Close, waiting for
you to change the disc and close the tray.
3.
The Previous Track Button
Press this button to start the previous track.
7
Page 20
4. The Next Track Button
Press this button to start the next track.
5.
The Volume Buttons
Press the left button to decrease the volume or the right button to increase the volume
of the played track.
6.
Audio DJ Power Button
Slide this Power button to power on the audio DJ.
NOTE:
You will not be able to use this button to turn off the Windows based
CD Player application when the notebook computer is in operation.
The Left Side
8
Page 21
1. Ventilation Opening
Please don’t block this opening during operation of the system.
2.
The LAN Port
This jack provides a standard RJ-45 connection for integration with an existing
network or a high-speed (ADSL or cable) connection via a network cable.
NOTE:
When using a LAN, please use an EMI Shielding Cable to
minimize an inteference when transmitting.
3.
1394 USB
A fast external bus standard that supports data transfer rates of up to 400 Mbps (400
million bits per second). Can be used to connect up 63 external devices, also supports
isochronous data -- delivering data at a guaranteed rate.
This makes it ideal for devices that need to transfer high levels of data in real-time,
such as video devices. Also supports both Plug-and-Play and hot plugging, and also
provides power to peripheral devices.
4.
PCMCIA Socket Cover
Open this cover to access the PCMCIA socket. The computer’s PCMCIA socket lets
you extend the capabilities of your computer by inserting PC cards.
5.
PCMCIA Socket Button
The computer has one PCMCIA type II socket
6.
Battery Charge/Suspend
This indicator will lit when the battery is in charging status. It also indicates when the
system enter suspend mode.
9
Page 22
7. Power On
This indicator will lit when the notebook is powered on.
The Right Side
1.
The DVD-ROM or DVD Combo
Your Notebook comes with a swappable 5.25" IDE 8X DVD-ROM or 16X Combo
drive.
10
2.
USB Ports
Your computer includes four Universal Serial Bus (USB) 2.0 port. USB2.0 is the
latest development in Plug and Play technology.
It will eventually replace the need for separate connectors for external keyboards,
serial ports, and parallel (printer) port.
Page 23
The Rear
1.
Audio Line Out/SPDIF Jack
You can plug an external speaker, headphone or connect the line out jack to an audio
device such as a cassette recorder to record the notebook's audio output.
S/PDIF engine receives the digital format data from DVD-ROM or Combo drive,
regroup the date to be synchronous signal and de-multiplexes audio and other digital
data.
2.
External Microphone Jack
This mono microphone jack is used to connect an external microphone.
3.
Infrared Data Port
The Infrared Data Port allows your Notebook to become truly wireless. You can use
this port to transfer large amounts of data very quickly to any other machine
(Notebook computers, printers, etc.) which is also equipped with an IrDA-compliant
IR port.
11
Page 24
This allows you to print documents without any inconvenient cable hookups.
4.
Parallel Port
This port allows you to easily connect a parallel printer or plotter using this 25-pin bidirectional female port.
5.
External CRT Port
This port allows you to easily connect an external VGA/SVGA display monitor into
your Notebook using the 15-pin female connector.
6.
TV Out Port
This 4-pin S-Video port allows you to view the Notebook's Video output on a
television monitor.
7.
The Modem Port
This jack is an internal 56K voice/fax/data modem. You will connect your computer
to your phone line through this port.
12
NOTE:
Always disconnect all telephone lines from the wall outlet before
servicing or disassembling this equipment. To reduce the risk of fire use only
No. 26 AWG or larger telecommunication line cord.
8.
DC IN Connector
Plug the AC adapter into this connector.
9.
Ventilation Opening
Please don’t block this opening during operation of the system.
Page 25
The Bottom Panel
1.
Battery
Your notebook comes equipped with a factory-installed battery pack module. After
the battery runs down, the module can be removed and replaced with a charged battery.
2.
Battery Release Latch
Lift up this latch to release the battery from its bay.
13
Page 26
3. Expansion Compartment
This compartment will serve as an expansion to upgrade your RAM module.
4.
DVD-ROM Release Latch
Push this latch to release the DVD-ROM from its bay.
5.
Hard Disk Drive
Your computer includes a 2.5-inch IDE hard disk drive (9.5mm in height). The
notebook PC's BIOS automatically detects IDE drive types.
14
Page 27
2
Getting Started
Page 28
Connecting to a Power Source
Connecting the AC Adapter
A universal AC adapter is provided to supply your computer with power and also charge
the computer’s battery pack.
The adapter’s AC input voltage can range anywhere from 100 to 240 volts, covering the
standard voltages available in almost every country.
The power cord for the AC adapter requires a three-hole grounded AC outlet. To connect
the computer to an external power source:
1.
Plug the AC adapter’s connector into the DC-IN connector on the rear of the
computer.
2.
Connect the power cord to the AC adapter and then to a wall outlet.
16
Page 29
CAUTION: The best kind of AC power source to connect your Notebook to
is a UPS (Uninterruptible Power Supply). Lacking this, use a power strip
with a built-in surge protector. Do not use inferior extension cords as this
may result in damage to your Notebook. The Notebook comes with its own
AC adapter. Do not use a different adapter to power the computer and other
electrical devices.
Whenever possible, keep the AC adapter plugged into the Notebook and an electrical
outlet to recharge the battery.
CAUTION: Never turn off or reset your Notebook while the hard disk is in
use and the HDD status icon is lit; doing so can result in loss or destruction
of your data. Always wait at least 5 seconds after turning off your Notebook
before turning it back on; turning the power on and off in rapid succession
can damage the Notebook’s electrical circuitry.
Turning On Your Notebook Computer
Turn on your Notebook by pressing the power button. Hold the button down for a second
or two and release. The Power-On Self Test (POST) runs automatically.
After the POST is completed, the computer reads the operating system from the hard disk
drive into computer memory (this is commonly referred to as “booting” a computer). If
your OS (Operating System such as Windows ME, Windows 2000…. etc) is installed, it
should start automatically.
To turn the Notebook off, save your work and close all open applications, click on Start,
then Shu
button for 4-6 seconds.
t Down and select Shut down the computer and click "Yes" or press the power
17
Page 30
Operating on Battery Power
Your computer comes with a rechargeable battery pack that lets you operate the computer
without an external power source. When the battery pack is fully charged, you can
operate the computer for approximately 2 hours under the following conditions:
• The battery pack initially has a full charge.
• No peripheral devices are installed.
• The disk/DVD-ROM drives run no more than 10% of the time.
NOTE: Only use batteries that are approved by an authorized dealer. All
batteries are not the same and therefore should not be treated as such. Using the
wrong battery could cause serious damage to your computer and yourself
through toxic emissions.
Inserting and Removing the Battery Pack
The battery pack should already be inserted in your Notebook computer when you unpack
it. If not inserted, follow these directions:
1.
Turn over the notebook with the front of the unit facing you and place it on a solid,
flat surface.
2.
Angle the battery into the bay. The front edge of the battery should slide into the
grooves in the system case.
18
Page 31
3.
Gently lower the battery into the bay and push it until it clicks securely in the bay.
To remove the battery pack:
1.
Turn off the notebook, and disconnect the AC adapter. Close the LCD panel and
turn it over and place it on a solid, flat surface.
2.
Lift the release latch to release the battery from the bay. At this time the battery
will now be angled slightly out of the bay.
19
Page 32
20
3. Hold the battery at the finger grip and lift it out of the compartment.
Page 33
Charging the Battery Pack
The installed battery pack charges automatically any time the computer is connected to
the AC adapter and an external power source.
If this is your first time to use the battery, be sure to fully discharge the battery and
recharged until it is fully charged.
21
Page 34
22
Page 35
3
Using the Notebook
Computer
Page 36
Adjusting the LCD Screen Display
The LCD screen display can be adjusted by the following key combinations.
KEYS FUNCTIONS
[Fn] + [F7] Decreases the brightness level.
[Fn] + [F8] Increases the brightness level.
[Fn] + [F10]Use this key combination to expand your video screen or reset to its
original size.
[Fn] + [F12]This key combination toggles the display between the LCD, CRT,
simultaneous LCD/CRT, TV, simultaneous CRT/TV.
LCD Care
LCD screens are delicate devices that need careful handling. Please pay attention to the
following precautions:
• When you are not using the computer, keep the LCD screen closed to protect it from
dust.
• If you need to clean your LCD screen, use a soft tissue to gently wipe the LCD surface.
• Do not put your fingers or sharp objects directly on the surface and never spray cleaner
directly onto the display.
• Do not press on, or store any objects on the cover when it is closed. Doing so may
cause the LCD to break.
24
External CRT Display
You can hook up an external monitor through the 15-pin CRT connector. Five
configurations are available:
• LCD only
• CRT only
• Simultaneous display of the LCD screen and CRT monitor
Page 37
• TV only
• Simultaneous display of the TV screen and CRT monitor
You can switch between these display configurations by pressing the key combination [Fn]
+ [F12]. For information on connecting an external display, please refer to Chapter Four.
A Tour of the Notebook’s Keyboard
The Notebook’s keyboard uses a standard QWERTY layout with the addition of special
function keys and an embedded numeric keypad for number intensive data entry. Your
keyboard supports Windows by incorporating the two Windows specific keys. With the
two Windows keys you will be able to access and take advantage of many of the
timesaving features of Windows software.
The function keys (F1-F12) on the top row of the keyboard, serve different purposes and
carry out different tasks depending on the application you are running.
The cursor (arrow) keys (which are all located in the lower right corner of your keyboard)
and the [PgUp], [PgDn], [Home] and [End] keys (which are located along the right edge
of the keyboard) allow you to move the active cursor of the computer to various locations
on the screen or within the document.
The embedded numeric keypad consists of 15 keys that make number intensive input
more convenient. Like the [Num Lock] key, these keys are labeled in blue on the keycaps.
Numeric assignments are located at the upper right of each key.
When the numeric keypad is engaged, the NumLock icon will appear in the System
Window. The keypad is activated by pressing the [Fn] + [NumLk] key. If an external
keyboard is connected, pressing the NumLock key on either the Notebook or external
keyboard will enable/disable NumLock of both keyboards in unison.
To disable the Notebook numeric keypad while keeping the keypad on an external
keyboard activated, use the [Fn] + [NumLk] hot key on the Notebook keyboard.
25
Page 38
The Notebook’s Hot Key Controls
KEYS FUNCTION(S)
Power Button Press this button once to power on or enter the suspend/resume
Internet ButtonOpen Internet WWW Home short-cut key
Email Button Open Email Reader short-cut key
[Fn] + [F2] This key combination turns on/off the volume.
[Fn] + [F3] Decreases the speaker volume.
[Fn] + [F4] Increases the speaker volume.
[Fn] + [F7] Decreases the brightness level.
[Fn] + [F8] Increases the brightness level.
[Fn] + [F10] Use this key combination to expand your video screen or reset to its
[Fn] + [F12] This key combination toggles the display between the LCD, CRT,
The TouchPad
mode.
Press this button for more than 4 seconds to power off the system.
original size.
simultaneous LCD/CRT, TV, simultaneous CRT/TV.
26
The touchpad is a rectangular electronic panel located just below your keyboard. You can
use the static-sensitive panel of the touchpad and slit it to move the cursor. You can use
the buttons below the touchpad as left and right mouse buttons.
Page 39
TouchPad Precautions
The TouchPad is a pressure sensitive device. Please take note of the following
precautions.
• Make sure the TouchPad does not come into contact with dirt, liquids or grease.
• Do not touch the TouchPad if your fingers are dirty.
• Do not rest heavy objects on the TouchPad or the TouchPad buttons.
27
Page 40
You can use the TouchPad with Microsoft Windows as well as non-Windows applications.
Connecting an External Tracking Devices
The system will only enables you to use one tracking device whether it is an internal or
external tracking device.
Data Storage and Retrieval
Data storage and retrieval are two of the most fundamental tasks you will perform when
working with your computer. The Notebook is equipped with a hard disk drive (HDD).
The HDD is removable allowing for easy upgrades.
The DVD-ROM/Combo
Features of the DVD-ROM/Combo Module
The features of the DVD-ROM/Combo drive are listed below.
• The Audio Play feature allows you to play music CDs
• Always hold the disc by the edges, avoid touching the surface.
• Use a clean, dry, cloth to remove dust, smudges, or fingerprints. Wipe from the center
outward.
• Do not write or place objects on the surface of the disc.
Page 41
• Store discs in a cool dry place not to damage the disc.
• Do not use benzene, thinners, or cleaners with detergent. Only use DVD-ROM
cleaning kits.
• Do not bend or drop the discs.
Loading a Disc
To play a CD disc, follow the instructions listed below.
1.
Push the DVD-ROM/Combo eject button on the CD drive door. Gently pull the
tray all the way out.
2.
Carefully lift the DVD-ROM/Combo by the edges and make sure the shiny surface
is face down (the side with no writing on it). Carefully insert the DVD-ROM onto
the tray. Push the DVD-ROM down gently so that it snaps onto the center ring.
3.
Push the tray back into the drive.
To remove a disk, do the following:
1.
Check the LED display and make sure that the computer is not accessing the DVDROM drive.
2.
Push the eject button and pull the tray all the way out.
3.
Carefully pick up the CD disk by the edges and – while pressing down on the center
ring – remove the DVD-ROM/Combo from the tray.
29
Page 42
NOTE: Do not insert any foreign objects into the disc tray. If you
experience difficulty when ejecting the CD disk tray, stretch a paper clip (or use
a pin or a thin metal rod) and insert it into the emergency eject hole located on
the right side of the front panel. The CD disk tray should eject immediately.
This procedure can also be used to remove a CD from the drive when the
Notebook is powered off.
Removing the DVD-ROM/Combo Drive
30
1. Push the release latch into the direction of the arrow as described in the illustration.
Page 43
2. Pull out the DVD-ROM drive from the bay.
PCMCIA Cards and Expansion Sockets
The Notebook features one PCMCIA expansion socket design to interface with one Type
II card.
Inserting a PCMCIA Card
The computer will emit a medium tone followed by a high tone when a PC card is inserted.
When you eject a card, the computer will emit a high tone followed by a medium tone.
You can insert and remove a PC card whether the computer is turned On or Off.
Follow these instructions to insert a PCMCIA card:
1.
Hold the PCMCIA card with the arrow side up and the connector side toward the
socket.
2.
Align the card connectors with the socket and carefully slide into the socket until it
locks into place. The system will beep once to indicate that it has detected the PC
card.
To remove a PC card push the eject button, the button will pop out, push the button again
to eject the PCMCIA.
NOTE:
When inserting a Type II PC card, make sure the connector is
inserted in the socket. Before ejecting a PC card, ensure that it is not being
accessed by the System.
For example, if the message “Write protect error writing Drive x” is displayed,
the user has to change the write protect switch setting on the memory card. To
change the switch setting, (a) eject the card, (b) change the switch setting, and (c)
re-insert the card.
31
Page 44
CAUTION: Always disconnect all telephone lines from the wall outlet
before servicing or disassembling this equipment. To reduce the risk of fire,
use only No. 26 AWG or larger telecommunication line cord.
Power Saving Modes
This section contains information on the Notebook’s power system, including the AC
Adapter, the battery system, recharging the battery, and tips for conserving battery power.
The power system is comprised of two parts, the AC Adapter and the battery system. The
AC Adapter converts AC power from a wall outlet to the DC power required by the
computer.
The Battery Power System
A fully charged pack will provide approximately 2 hours of battery life depending on your
system configuration application it runs.
Before using the computer on battery power for the first time, check the battery status
icon on the Windows Toolbar to make sure the battery is fully charged.
See Battery Status later in this section for a description and explanation of the Windows
Battery icon. Charging the battery takes about 3 hours to charge when the system is in off
state. If possible, always charge the battery completely.
32
Removing the Battery Pack
To remove the battery pack from its compartment, please refer to Chapter Two, Inserting
and Removing the Battery Pack.
Page 45
Preparing the Battery Pack for Use
Before using the battery pack for the first time, the Smart Battery IC within the battery
pack should be calibrated in order to get accurate reporting of remaining battery life status.
To calibrate the battery pack follows the instructions below:
1.
Insert the battery into the battery compartment and turn on the Notebook. If the
battery is completely without power go to the next step.
Otherwise, let the battery run down until the battery low-low warning beeps are
heard.
The system will automatically enter Suspend mode.
2.
Turn the Notebook off. Connect the AC adapter and let the battery fully recharge.
When the battery charge indicator turns off, the battery is fully charged.
3.
Turn On the notebook, let the battery run down until the battery is in low-low state
and you hear a warning beeps. The system will automatically enter the Suspend
mode. You can now connect the AC adapter.
4.
The battery pack is now calibrated properly.
In general, using the battery until the low-low battery-warning indicator appears and fully
recharges the battery each time (full discharge/charge cycle) will ensure the accurate
reporting of the battery gauge status.
Automatic Battery Pack Charging Function
You can automatically charge the battery pack by using the AC Adapter. The charge time
is about three hours when the Notebook power is turned off. The following table
summarizes the charging modes:
Charge ModeCharge Time
Fast 3 hours with the system off or in Suspend mode. The temperature
must be 25°C or below room temperature.
Pre-Charge A pre-charge is supplied to the Li-Ion battery pack.
33
Page 46
Battery Status
Windows 98/ME/2000/XP has an applet in the Control Panel that will display an icon in
the Windows taskbar indicating when the Notebook is running on battery power or is
attached to the AC adapter.
This applet also displays a meter that indicates how much charge is remaining in the
battery.
Battery Low Warning
When the pack initially reaches the “Battery Low” state approximately 10 ~ 15 minutes of
the usable battery life is left.
You will hear an audible beep signal every 1.5 seconds alerting you to the “Battery Low”
status. When the battery power reaches the “Battery Low Low” status the beeping sound
will accelerate.
Your battery now has 1 ~ 2 minutes of battery charge remaining. You must save your
data or connect AC power immediately; otherwise, you may lose your data.
Sound Meaning
Continuous beeping
every 1.5 seconds
Beeping accelerates Battery Low Low: Indicates that there is 1 to 2 minutes of
Battery Low: Indicates that there is 7 to 10 minutes charge
remaining.
battery charge remaining. Save your work and turn off the
Notebook, or connect the AC adapter.
34
When there is only one minute of battery charge remaining, the Notebook will suspend to
the HDD and power off. You should connect AC power and resume to save your work.
Page 47
Small Battery for the Real Time Clock
There is a small built-in battery pack that supplies power to the system in order to
maintain certain system information while the power is off.
If the Notebook is left without a power source for long period of time, this battery will be
exhausted and system information will be lost.
WARNING: Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the
manufacturer's instructions. Never remove the battery pack while the
power is on as this may result in data loss when the system loses
power.
Resetting the System
After installing a software application package, you may be prompted to reset the system
to load the changed operating environment. To reset the system, or “reboot,” press the
[Ctrl] + [Alt] + [Delete] keys simultaneously. This is known as “warm boot.” This key
combination acts as “software” reset switch when you encounter hardware or software
problems, which lock up the Notebook.
If this key combination does not shut down the Notebook, you can reset the Notebook by
using the Notebook’s power button. Should the Notebook lock up for some reason,
pressing this button powers the Notebook off.
Adjusting the Brightness
To adjust the brightness on the LCD screen, press and hold down the [Fn] key in the
lower left hand corner of the keyboard and press the [F7] key to reduce the brightness or
[F8] to increase the brightness.
35
Page 48
36
Page 49
4
Desktop Operation
Page 50
Audio
Your notebook is capable of providing you with efficient and productive mobile
computing, it also has the speed and capacity to service as a desktop system.
This chapter discusses those functions of your notebook that are typical of desktop
systems.
The Multimedia Sound System
The Notebook’s built-in audio capabilities allow you to take advantage of a wide range of
education and entertainment multimedia software. The Notebook is equipped with two
internal stereo speakers, a microphone, and input audio ports for external audio units.
An external microphone can be connected to the microphone jack. External speakers or
headphones can be connected to the Notebook’s audio-out jack.
External audio devices can be connected to the Line in jack. All audio features are
software controlled. The Notebook’s multimedia sound system includes the following
features:
• Supports Windows Sound System compatibility
• Full Duplex operation
• Dynamic filtering reduces noise and distortion rate
• 16-bit digitized audio playback
• A built-in microphone for convenient recording
• Two built-in stereo speakers
• Digitized audio recording through the Notebook’s built-in microphone or any external
source
38
Page 51
Audio Volume Control
The Notebook is equipped with hot-key volume controls: Pressing the [Fn] + [F3] hot-key
combination decreases the audio output volume, press the [Fn] + [F4] hot-key
combination increases the audio output volume.
Audio Software
Your notebook comes equipped with an integrated sound system capable of providing you
with quality audio sound through the built-in speakers or through external speakers
connected via the system ports.
Sound Recording
Your system allows you to record sounds and store them as files using the microphone via
the microphone jack on the rear of the notebook computer. Check the Windows Help and
Support Center in Windows for information on using the various elements in sound
recording.
NOTE: For a high-quality sound, click on the "Volume Control" at the
lower right end of your screen. From the Volume Control windows, click on the
"Advanced" tab, click and select the "Microphone Boost" item.
Playing Sound Files
Your notebook can play audio files stored in MIDI, WAVE or MP3 file format. Check
the Help and Support Center in Windows for information on the functions of the Media
Player.
39
Page 52
External Speakers and Microphone
The sound system is capable in providing high-quality sound to external speakers and
receiving and processing sounds from an external microphone or external sound source.
Connecting Peripheral Devices
To expand your computing capabilities, you can add a variety of external devices to your
computer. You may, for example, want to add a mouse, modem, or a printer.
The computer is equipped with several interface ports, including an enhanced parallel
(printer) port, a serial port, and USB ports. These are provided as a means of connecting
peripheral devices to the computer.
Connect peripheral devices to the computer's interface ports as shown below:
40
Page 53
41
Page 54
42
Page 55
5
Running BIOS
Setup
Page 56
Introduction
The BIOS (Basic Input and Output System) Setup program is a menu driven utility that
enables you to make changes to the system configuration and tailor your system to reflect
installed hardware or alter system performance. When the Notebook is turned back on, the
system is configured with the values stored in CMOS. With easy-to-use menus, you can
configure such items as:
• Hard drives and peripherals
• Boot up Drive Sequence
• Password protection
• Power Management Features
The settings made in the BIOS Setup program intimately affect how the Notebook performs.
Navigating through BIOS Setup
The Setup program has been designed to make it as easy to use as possible. If you
accidentally make a setting and don’t know which one to switch back to, the Setup program
has a hot key that allows you to return to the previous value.
Accessing the BIOS Setup Program
To access the BIOS Setup program, press the F2 key after the Notebook has run through its
POST.
Item Specific Help
On the right side of the Setup screen is an area labeled Item Specific Help. This area will list
navigation key shortcuts and information that is specific for the item that you are currently
editing.
The Menu Bar
44
Page 57
The top of the screen has a menu bar with the following selections:
• Main - Use this menu to make changes to the basic system configuration.
• Advanced - Use this menu to enable and make changes to the advanced features
available on your system.
• Security - Use this menu to set a password. The password allows boot up and
controls access to the BIOS setup menu.
• Boot - Use this menu to configure the default system device used to locate and load
the Operating System and for booting up the Notebook.
• Exit - Use this menu to exit the current menu or specify how to exit the Setup
program.
To access the menu bar items, press the right or left arrow key on the keyboard until the
desired item is highlighted.
The Legend Bar
At the bottom of the Setup screen you will notice a legend bar. The keys in the legend bar
allow you to navigate through the various setup menus.
The following table lists the keys found in the legend bar with their corresponding alternates
and functions.
Legend KeyAlternate KeyFunction
F1 Alt + H Displays the General Help window. It can be enabled
from anywhere in the BIOS.
Esc Alt + X Jumps to the Exit menu or returns to the Main menu from
a submenu.
←
→
↑ or ↓
Tab Enter Moves the cursor to the next position available in the field.
Selects the menu item to the left.
Selects the menu item to the right.
Keypad arrow
keys
Moves the cursor up and down between fields.
45
Page 58
Shift+ Tab Moves the cursor to previous position available in the
Minus key
(
-)
Plus key (+)F6, Space Scrolls forward through the values for the highlighted field.
Home PgUp Moves the cursor to the field at the top of the window.
End PgDn Moves the cursor to the field at the bottom of the window.
F9 Sets the parameters for the current menu to their default
F10 Save and Exit.
Enter Will select a sub menu or show a range of options for a
F5 Scrolls backward through the values for the highlighted
Launching Submenus
Note that a right pointer symbol appears to the left of certain fields. This pointer indicates
that a submenu can be launched from this field. A submenu contains additional options for a
field parameter. To call up a submenu, simply move the cursor to highlight the field and
press the [Enter] key. Use the [Esc] key to return to the Main menu.
field.
field.
values.
field.
General Help
In addition to the Item Specific Help window, the BIOS Setup program also provides a
General Help screen can be called up from any menu by simply pressing [F1] or the [Alt] +
[H] combination.
46
Page 59
Use the [PgUp] and [PgDn] keys or the up and down arrow keys (↑↓) to scroll through the
entire help document. Press the Home key to display the first page, press End to go to the
last page. To exit the help window, press the [Enter] or the [Esc] key.
Save Changes and Exit the Setup Program
Refer to the Exit menu section of this chapter for detailed information on saving changes and
exiting the setup program.
The Main Menu
When the Setup program is accessed, the following screen appears:
47
Page 60
System Time
Sets your system to the time that you specify. The format is hour, minute, second.
Use the [Tab] or [Shift] + [Tab] keys to move between the hour, minute, and second
fields.
System Date
Sets your system to the date that you specify (usually the current date). The format
is month, day, year. Use the [Tab] or [Shift] + [Tab] keys to move between the
month, day, and year fields.
`
Primary Master
This field is used to configure the IDE Hard Disk installed in the system. To configure a
hard disk drive, move the cursor to highlight the Primary Master field:
` Primary Master [IC25N040ATCS04-0- (PM)]
Pressing the [Enter] key at this point will reveal the Primary Master submenu:
48
Page 61
NOTE: Before attempting to configure a hard disk drive, make sure you have
the configuration information supplied by the manufacturer of your hard drive.
Incorrect settings can result in your system not recognizing the installed hard disk.
Type
The following options are available for this field:
Auto (default value), None
Select Auto to automatically configure an IDE type drive. This option only works
with standard IDE drives. If your drive is an IDE type, it will be automatically
49
Page 62
recognized and properly configured.
If automatic detection is successful, the correct values will be filled in for the
remaining fields on this submenu. If no drive is installed or if you are removing a
drive and not replacing it, select None.
DVD-ROM if a DVD-ROM is installed as the IDE Adapter 0 Master.
To configure a drive that is not an IDE type drive, if it is User. Manually enter the
number of cylinders, heads and sectors per track for your drive. Refer to your
drive’s documentation or look on the drive if you need to obtain this information.
ATAPI Removable if the drive is an ATAPI type drive that supports high-capacity
storage diskettes. This option would be used in the event that you have swapped the
DVD-ROM for an ATAPI type removable drive.
Total Sectors
This field configures the drive’s number of sectors per track. If the system has
successfully detected the drive automatically, there is no need to adjust this field. In
order to make changes to this field, the Type field must be set to User.
Maximum Capacity
50
This field gives the maximum formatted capacity of the hard disk drive. This is a
display only field.
Multi-Sector Transfers
This option automatically sets the number of sectors per block to the highest number
supported by the drive. This field can also be configured manually. Note that when
this field is automatically configured, the set value may not always be the fastest
value for the drive.
Refer to the documentation that came with your hard drive to determine the optimal
value and set it manually. In order to make changes to this field, the Type field must
be set to User. Configuration options are:
When enabled, this option uses 28-bit addressing of he hard drive without regard for
cylinders, heads, and sectors.
Note that Logical Block Access may decrease the access speed of the hard disk.
In order to make changes to this field, the Type field must be set to User.
Configuration options are:
Disabled, Enabled (default value)
32 Bit I/O
When enabled, this option speeds up communication between the CPU and the IDE
controller. This option supports PCI local bus only. ISA bus is not supported. Set
the Type field to Auto to provide the optimum transfer mode. Configuration options
are:
Disabled, Enabled (default value)
Transfer Mode
When enabled, this option speeds up communication between the system and the
IDE controller by using enhanced I/O transfer modes (PIO) Modes.
Set the Type field to Auto to provide the optimum transfer mode. Configurations are:
Standard, Fast PIO 1, Fast PIO 2, Fast PIO 3, Fast PIO 4, FPIO 3
/ DMA 1, FPIO 4 / DMA 2
Ultra DMA Mode
When enabled, this option speeds up data transfer to and from the drive. In order to
make changes to this field, the Type field must be set to User.
51
Page 64
Set the Type field to Auto to provide the optimum transfer mode. Configurations are:
After using the legend keys to make changes to this submenu, press the [Esc] key to
exit back to the Main menu.
`
Secondary Master
The value in this field indicates the type of your Notebook’s DVD-ROM drive. The
arrowhead icon
indicates that this field contains a submenu. The submenu is used to
configure a DVD-ROM installed in the system.
To configure a DVD-ROM, move the cursor to highlight the Secondary Master field, and
press the [Enter] key. The Secondary Master submenu screen will appear. When the Type
field is set to “Auto”, only the 32 Bit I/O and Ultra DMA Mode fields are available. When
set to “User” the fields and options on this submenu are the same as the IDE Adapter 0 Master submenu described above.
After using the legend keys to make your selections to this submenu, press the [Esc] key to
exit back to the Main menu.
52
Page 65
Summary Screen
This field display the system configuration when you boot up the system.
Disabled (default value), Enabled
System Memory
This field display the amount of conventional memory detected by the system during
bootup. You do not need to make changes to this field. This is a display only field.
Extended Memory
This field displays the amount of extended memory detected by the system during
53
Page 66
boot-up. You do not need to make changes to this field. This is a display only field.
The Advanced Menu
Selecting Advanced from the menu bar displays the advanced menu:
54
`
I/O Device Configuration
This menu allows you to configure the notebook's serial and parallel ports diskette controller
as well as the peripherals connected to your system. Each field on this submenu is covered
below.
Page 67
Parallel Port
This field allows you to configure the Notebook’s parallel port.
The following options are available:
Disabled, Enabled (default value)
Changing the default address and IRQ settings for COM1 and the LPT Port can
cause conflicts with other system devices or installed peripherals.
55
Page 68
IrDA/FIR
This field allows you to enable or disable the Notebook's Fast Infrared (FIR)
communication module. The following configuration options are available:
Disabled, Enabled (default value)
Base I/O Address
When the Parallel Port is set to Enabled, the "Base I/O Address" field becomes
available and you can set the parallel port's I/O address. Available configurations are:
3F8, 2F8 (default value), 3E8, 2E8
Interrupt
Use this option to choose the Interrupt for the Sound chip. Available configurations
are:
IRQ 3 (default value), IRQ 4
Mode
This field allows you to configure the notebook's Fast Infrared (FIR) communication
module. Available configurations are:
IrDA, FIR (default value)
The Security Menu
The Notebook’s advanced system of security allows you to set a password to prevent
unauthorized access to system resources, data, and the BIOS Setup Program.
56
Page 69
Supervisor Password Is:
This field will show Set when you have set a Supervisor Password as described
below. If you have not set the Supervisor Password, the field will show Clear. This
is a display only field.
User Password Is:
This field will show Set when you have set a User Password as described below. If
you have not set the User Password, the field will show Clear. This is a display only
field.
57
Page 70
Set Supervisor Password
This field allows you to set the Supervisor password. To set the Supervisor
password, highlight this field and press the [Enter] key. The following dialog box
appears:
Set Supervisor Password
Enter New Password[ ]
Confirm New
Password
Type the password and press the [Enter] key. You can type up to seven
alphanumeric characters. Symbols and other keys are ignored. To confirm the
password, type the password again and press the [Enter] key. The Supervisor
password is now set. This password allows full access to the BIOS Setup menus.
To clear a password, highlight this field and press the [Enter] key. The same dialog
box as above will appear. Press the [Enter] key twice. The password is now cleared.
[ ]
Set User Password
This field allows you to set the User password. To set the User password, follow the
same instructions for setting the Supervisor password. The User password allows
restricted access to the Setup menus.
58
This password also requires that the Supervisor password be set prior to setting the
User password.
Diskette Access
This option requires prior setting of the Supervisor password to function. When set
to User, the system will then require either the Supervisor or User password before
allowing access to the Floppy Disk Drive (FDD). When set to Supervisor, only the
Supervisor password will allow access to the FDD. The options for this field are:
User (default value), Supervisor
Page 71
Password on Boot
This option requires prior setting of the Supervisor password to function. When
enabled, the system will then require either the Supervisor or User password before
the system can bootup. The options for this field are:
Disabled (default value), Enabled
Fixed Disk Boot Sector
This option requires prior setting of the Supervisor password to function. When set
to Normal, the system will allow normal access to the HDD boot sector. When set to
Write Protect, the BIOS blocks all accesses to the boot sector. The options for this
field are:
Normal (default value), Write Protect
NOTE: Write protecting the HDD boot sector will protect the HDD against
boot sector viruses. However, this option may interfere with the normal operation
of certain operating systems or anti-virus programs, which would normally need
access to the boot sector area.
The Boot Menu
The Boot menu allows the user to specify the order in which the Notebook is to check for a
device to boot the system. You can also configure the way that the system will boot up. To
make changes, select Boot from the menu bar.
The following screen appears:
59
Page 72
Use the up and down arrows to select the boot device. Then press either the plus key [+] to
move the device up the list or the minus key [-] to move the device down the list.
The Exit Menu
Once you have made all of your selections from the various menus in the Setup program, you
should save your changes and exit Setup. Select Exit from the menu bar to display the
following menu:
60
Page 73
NOTE: Pressing the [Esc] key does not exit this menu. You must select one of
the options from this menu or a menu bar item to exit this menu.
Exit Saving Changes
Once you are finished making your selections, choose this option from the Exit menu
to ensure the values you selected are saved to Non-Volatile RAM.
Setup Confirmation
Save configuration changes and exit now?
61
Page 74
[Yes] [No]
Select Yes to save changes and exit the BIOS setup program or press [Esc] to return
to the Exit menu.
The next time you bootup the Notebook, the BIOS will attempt to load the values
you saved in Non-Volatile memory. If these values cause the system boot to fail,
reboot and press [F2] to enter the Setup program.
Once in Setup, you can try to change the values that caused the system boot to fail.
If the problem persists, load the default values as described below.
NOTE: If you attempt to exit the Setup program without saving your changes,
the program will prompt you with a message asking if you want to save your
changes before exiting.
Exit Discarding Changes
This option should only be used if you do not want to save the changes you have
made to the Setup program. If you have made changes to the fields other than
system date, system time and password, the system will ask for confirmation when
choosing Exit Discarding Changes.
62
Warning
Configuration has not been saved!
Save before exiting?
[Yes] [No]
Select Yes to save changes and exit the BIOS setup program, select No to exit BIOS
without saving your changes, or press [Esc] to return to the Exit menu.
Page 75
Load Setup Defaults
This option allows you to load the default values for each of the parameters on the
Setup menus.
Setup Confirmation
Load default configuration now?
[Yes] [No]
Select Yes to load default values. You can now select Exit Saving Changes or make
other changes before saving the values to Non-Volatile RAM.
Discard Changes
This option allows you to discard the selections you’ve made and restore the values
you previously saved.
Setup Confirmation
Load previous configuration now?
[Yes] [No]
Select Yes to discard any changes and load the previously saved values.
Save Changes
This option saves your selections without exiting the Setup program. You can then
return to other menus and make changes.
Setup Confirmation
Save configuration changes now?
[Yes] [No]
Select Yes to save any changes to Non-Volatile RAM. To exit the BIOS Setup
program, open the Exit menu and select one of the exit options.
63
Page 76
NOTE: To exit BIOS Setup without saving your changes, select Exit
Discarding Changes from the Exit menu and press [Enter]. When prompted by
BIOS to save your changes before exiting, select [No] and press [Enter].
64
Page 77
6
The Software
Utilities Disks
Page 78
There are two separate procedures on how to install the driver: AutoRun installation
and Manual installation.
AutoRun Installation
• Follow the step-by-step procedures on the DVD-ROM to execute the “AutoRun”
application by selecting the topic of “Driver Installation”.
• To re-run the “AutoRun” installation, please refer to the procedures on the
“Manual Installation” for a more detailed explanation.
Intalling the AGP Driver for WinXP
1.
Insert the DVD-ROM Driver into your DVD-ROM drive.
2.
Click “Start” and Select “Run”.
3.
Type the following: D:\Driver\AGP\SiSSetup.exe (If D is not your DVD-ROM
drive, substitute D with the correct drive letter).
4.
Click on “Setup” to begin the Installation Wizard.
5.
Follow the Wizard’s on-screen instructions to complete the installation.
6.
Restart the system.
66
Installing VGA Display Drivers for WinXP
This section describes the operation and installation of VGA display software drivers
supplied on the Driver Utility DVD-ROM that is shipped with your computer.
1.
Insert the DVD-ROM Driver into your DVD-ROM drive.
2.
Click “Start” and Select “Run”.
3.
Type the following: D:\Driver\VGA\ Setup.exe (If D is not your DVD-ROM drive,
substitute D with the correct drive letter).
4.
Click on “Setup” to begin the Installation Wizard.
5.
Follow the Wizard’s on-screen instructions to complete the installation.
Page 79
6. Restart the system.
Intalling the Audio Driver for WinXP
1.
Insert the DVD-ROM Driver into your DVD-ROM drive.
2.
Click “Start” and Select “Run”.
3.
Type the following: D:\Driver\Audio\Setup.exe (If D is not your DVD-ROM drive,
substitute D with the correct drive letter).
4.
Click on “Setup” to begin the Installation Wizard.
5.
Follow the Wizard’s on-screen instructions to complete the installation.
6.
Restart the system.
Intalling the LAN Driver for WinXP
To install the LAN driver you must first remove the currently installed driver.
1.
Insert the DVD-ROM Driver into your DVD-ROM drive.
2.
Click “Start” and Select “Run”.
3.
Type the following: D:\Driver\LAN\Setup.exe (If D is not your DVD-ROM drive,
substitute D with the correct drive letter).
4.
Click on “Setup” to begin the Installation Wizard.
5.
Follow the Wizard’s on-screen instructions to complete the installation.
6.
Restart the system.
Installing the USB20 Driver for WinXP
To install the USB20 driver you must first remove the currently installed driver.
1.
Insert the DVD-ROM Driver into your DVD-ROM drive.
2.
Click “Start” and Select “Run”.
3.
Type the following: D:\Driver\USB20\USB20.exe (If D is not your DVD-ROM
drive, substitute D with the correct drive letter).
67
Page 80
4. Click on “USB20” to begin the Installation Wizard.
5.
Follow the Wizard’s on-screen instructions to complete the installation.
6.
Restart the system.
NOTE:
Please note that Window XP Service Pack 1 provides built-in driver
for USB 2.0. Do not install USB 2.0 driver from driver CD if you already have
Windows XP Service Pack 1
Installing the IR Driver for WinXP
To install the IR driver you must first remove the currently installed driver.
1.
Insert the DVD-ROM Driver into your DVD-ROM drive.
2.
Click “Start” and Select “Run”.
3.
Type the following: D:\Driver\IR\Setup.exe (If D is not your DVD-ROM drive,
substitute D with the correct drive letter).
4.
Click on “Setup” to begin the Installation Wizard.
5.
Follow the Wizard’s on-screen instructions to complete the installation.
6.
Restart the system.
Installing the TouchPad&StickPoint Driver for WinXP
To install the touchpad driver you must first remove the currently installed driver.
1.
Insert the DVD-ROM Driver into your DVD-ROM drive.
2.
Click “Start” and Select “Run”.
3.
Type the following: D:\Driver\Touchpad&StickPoint\Setup.exe (If D is not your
DVD-ROM drive, substitute D with the correct drive letter).
4.
Click on “Setup” to begin the Installation Wizard.
5.
Follow the Wizard’s on-screen instructions to complete the installation.
68
Page 81
6. Restart the system.
69
Page 82
Manual Installation
To install the driver manually, follow the step-by-step procedures described on each
individual section for a more clear installation.
Installing the CardBus Driver for WinXP
Please follow these instructions to install the cardbus driver:
1.
From Start, click on the "My Computer" icon and click the "View System
Information".
2.
Click on the "Hardware" tab from the "System Properties" dialog window.
3.
Click the "Device Manager" button.
4.
Double click on the "PCMCIA adapters" , double click the "Generic CardBus
Controller" and click on the "Driver" tab.
5.
Click the "Update Driver" tab and select the "Install from a list or specific location
(Advanced)" item and click "Next".
6.
Select the "Include this location in the search" item and click on the "Browse"
button and specify for the designate location of your CD driver
D:\Driver\Cardbus\ENE1410\WinXP to proceed with the installation.
70
Installing the Actiontec Combo/Wireless LAN Driver for WinXP
1.
Click the "My Computer" icon and click on the "Control Panel" item to open the
Control Panel.
2.
Double click on the "System" icon. Click the "Device Manager" tab.
3.
Click on the "Other Devices" (denoted by the yellow mark symbol), select the
"Ethernet Controller" and click on the "Properties" tab.
4.
From the "Ethernet Controller Properties" window, click on the "Driver" tab and
select the "Update Driver" button.
5.
Click on the "Specify the location of the driver (Advanced)" and again click on the
Page 83
"Next" button.
6. Select the "Specify a location" and click the "Browse" button to locate the disk
drive of your DVD-ROM driver.
D:\Driver\MiniPCI\Actiontec\Wireless\WinXP to proceed with the installation.
Installing the Accton Combo/Wireless LAN Driver for WinXP
1.
Click the "My Computer" icon and click on the "Control Panel" item to open the
Control Panel.
2.
Double click on the "System" icon. Click the "Device Manager" tab.
3.
Click on the "Other Devices" (denoted by the yellow mark symbol), select the
"Network Controller" and click on the "Properties" tab.
4.
From the "Network Controller Properties" window, click on the "Driver" tab and
select the "Update Driver" button.
5.
Click on the "Specify the location of the driver (Advanced)" and again click on the
"Next" button.
6.
Select the "Specify a location" and click the "Browse" button to locate the disk
drive of your DVD-ROM driver.
D:\Driver\MiniPCI\Accton\wireless to proceed with the
installation.
Installing the Actiontec MiniPCI Combo Card Modem Driver for
WinXP
1.
Insert the CD-ROM Driver into your CD-ROM/DVD-ROM drive.
2.
Click “Start” and Select “Run”.
3.
Type the following: D:\Driver\MiniPCI\Actiontec\Modem\WinXP\Setup.exe (If D
is not your CD-ROM/DVD-ROM drive, substitute D with the correct drive letter).
4.
Click on “Setup” to begin the Installation Wizard.
5.
Follow the Wizard’s on-screen instructions to complete the installation. Restart the
system.
71
Page 84
Installing the Modem AM303W Driver for WinXP
1.
From your screen, click on the “My Computer” icon and use your mouse or
touchpad right button to select the “Properties” item.
2.
Click on the “Hardware” tab from the “System Properties” dialog window.
3.
Double click “Device Manager” tab.
4.
Select the “PCI Modem” in the “Modem” group (denoted by a yellow mark symbol).
5.
Click the “Driver” tab then click the “Update Driver” item.
6.
Select the “Search for a suitable driver for my device (recommended)” item and
click “Next”.
7.
Click the “Browse” button and specify for the designate location of your CD driver.
(D:\Driver\MiniPCI\AM303W\WinXP).
Installing the Accton Combo/AC-link MODEM Driver for WinXP
1.
Insert the CD-ROM Driver into your CD-ROM/DVD-ROM drive.
2.
Click “Start” and Select “Run”.
3.
Type the following: D:\Driver\MiniPCI\Accton\Modem\WinXP\Setup.exe (If D is
not your CD-ROM/DVD-ROM drive, substitute D with the correct drive letter).
4.
Click on “Setup” to begin the Installation Wizard.
5.
Follow the Wizard`s on-screen instructions to complete the installation.
6.
Restart the system.
VGA Utilities
After you have restarted Windows, open the “Control Panel” and double click on the
“Display” icon. From the “Display Properties” window, select the “Settings” tab and
click on the “Advanced” tab to enter the “Default Monitor and MOBILITY RADEON
8500 Properties" window.
72
Page 85
You will notice three new entries have been made in the Display Properties window: ATI
Displays, ATI color, ATI OpenGL, ATI Direct 3D, ATI POWERPLAY™, ATI Overlay
and ATI Options.
73
Page 86
ATI Display
With ATI Display, you can connect up to three displays simultaneously to the notebook.
You can watch a DVD movie on an external television while checking email on your
notebook screen - or surf the web on a CRT monitor while working on a presentation on a
digital flat panel. The option is yours with these features.
74
Page 87
ATI Color
You can adjust the right resolution for your screen display.
75
Page 88
ATI OpenGL
Play the latest and greatest OpenGL based games as well as CAD/Design programs.
76
Page 89
ATI Direct 3D
An API for manipulating and displaying 3-dimensional objects.
77
Page 90
ATI Options
Display all the items concerning the ATI related function.
78
Page 91
ATI POWERPLAY™
79
Page 92
ATI Overlay
80
Page 93
Troubleshooting
7
81
Page 94
This chapter describes locating and solving problems that you may encounter while using
your computer.
Locating a Problem
Problems with your computer can be caused by something as minor as an unplugged
power cord – or as major as a damaged hard disk. The information in this chapter is
designed to help you find and solve minor problems. If you try all the suggested solutions
and you still have a problem, make a list of what steps you have taken to correct the
problem and contact your dealer.
Successful troubleshooting is the result of careful observation, deductive reasoning, and
an organized approach to solving the problem.
The problems that you will encounter can be divided into two basic categories: hardware
problems and software problems. Hardware problems can be further divided into electrical
and mechanical problems. You will know you have a hardware problem if the screen is
dark, the computer cannot read the disk drives, or you get an error message during the
Power-On Self Test (POST).
Software errors can occur at several levels. The ROM BIOS and the operating system can
give you a large number of error messages. On top of this, each application software
package has its own set of error messages. It is important to determine whether the
software error message you are getting is from the application or the operating system.
Once you know this, you can look in the respective manual for a solution to the problem.
Checking Cables and Connections
Start by performing a careful visual inspection of the exterior of the computer. If no
LEDs are illuminated, make sure that your computer and its peripherals are getting power
and communicating with each other properly.
To check the power cables, and connections:
1. If you have been using battery power, connect the Notebook to an external power
source and make sure that the battery has a charge.
82
Page 95
2. If you are using the Notebook with the AC adapter, check the power outlet, the
power cord, and any power switches that may affect your computer.
• Check the wall outlet or power strip with an item that you know is functioning
properly. A lamp or radio is a convenient item for checking the power. You may
also need to check the fuses and breakers in your electric box.
• If the outlet is controlled by a wall switch, make sure that the switch is on.
• If the outlet is controlled by a dimmer switch, use a different outlet.
• If your computer is plugged into a power strip with an On/Off switch, make sure
the switch is on.
3.
With the computer’s power switched off, check all cable connections. If the
computer is connected to any peripheral devices, look for loose or disconnected
cables. If the computer is too close to a wall, a cable connection may be loose or
the cables may be crimped.
NOTE:
Do not substitute cables for different devices (other than the
manufacturer recommended cables) even if they look exactly alike. The wiring
inside the cable may be different.
4. When you are certain that you have power available and all connections are good,
turn the computer on again. If the computer still does not start, you may have a
hardware problem.
The Power-On Self Test
The Power-On Self Test (POST) runs every time you turn on or reset the Notebook. The
POST checks memory, the main system board, the display, the keyboard, the disk drives,
and other installed options.
83
Page 96
A few seconds after you turn on your computer, a copyright message appears on your
display screen. A memory test message appears next; as the test continues, memory size
increases until all installed memory is tested. Normally, the only test routine visible on the
screen will be the memory test.
Two classifications of malfunctions can be detected during the POST:
• Error messages that indicate a failure with either the hardware, the software, or the
Basic Input/Output System (BIOS). These critical malfunctions prevent the computer
from operating at all or could cause incorrect and apparent results. An example of a
critical error is microprocessor malfunction.
• Messages that furnish important information on the power-on and boot processes (such
as memory status). These non-critical malfunctions are those that cause incorrect
results that may not be readily apparent. An example of a non-critical error would be a
memory chip failure.
In general, if the POST detects a system board failure (a critical error), the computer halts
and generates a series of beeps. If failure is detected in an area other than the system
board (such as the display, keyboard, or an adapter card) an error message is displayed on
the screen and testing is stopped. It is important to remember that the POST does not test
all areas of the computer, only those that allow it to be operational enough to run
diagnostic programs.
If your system does not successfully complete the POST, but displays a blank screen,
emits a series of beeps, or displays an error code, consult your dealer.
General Hardware Problems
A few common hardware problems and suggested solutions are presented in the table
below:
Problem:
Solution:
84
The capacity of the battery is between 95 to 99% but can not fully charged.
Please discharged to less than 95% of its capacity then recharge the battery.
Page 97
Problem: Failure in the installation of the Audio driver.
Solution:
Be sure to first remove the current audio device from your system. Please
follow the instruction on the installation of audio driver.
Problem:
Solution:
The display screen is dark
Make sure that the computer is not in Suspend mode. Check the Brightness
controls for the screen. If the controls are turned too far down, the screen will be dark.
Problem:
Solution:
An incorrect date and time are displayed.
Correct the date and time using the DOS DATE and TIME commands or the
options in the Setup Utility. If the date and time become incorrect after a short time, your
CMOS battery may be depleted. Contact your dealer to change the battery.
Problem:
The message: “Invalid system disk, Replace the disk, and then press any key”
appears during boot.
Solution:
Check and make sure that you do not have a non-bootable floppy diskette
inserted in your floppy drive. If your USB FDD is empty, you may not have an operating
system installed on your drive. Contact technical support for assistance.
Problem:
Solution:
You hear irregular beeps during operation of the Notebook and the system halts.
The problem is beyond the scope of this manual. Contact technical support.
Problem:
Solution:
An unidentified message is displayed.
Reboot the computer and run the BIOS system setup. Confirm the Setup
parameters. If the same message is displayed after booting up again, contact technical
support for assistance.
Problem:
The system cannot access the DVD-ROM drive.
85
Page 98
Solution: Check that a CD is properly inserted in the drive. Make sure that you are using
the correct program for that kind of CD. For example, the system cannot read a data CD
using an audio program.
Problem:
Solution:
You cannot operate the printer.
Check the printer cable connection. Ensure that the printer power switch is
turned on. Confirm that the printer is on-line.
Problem:
Solution:
You can’t save data to disk.
Ensure that the disk has been formatted.
Consult your operating system manual for information on formatting floppy diskettes.
Problem:
Solution:
Problem:
Solution:
The diskette is write-protected.
Eject the diskette, remove the write protection, and try again.
The diskette if full.
Try using another diskette or free up some space on the diskette. The disk
drive is not operating. Contact your dealer for support.
Problem:
You cannot use the mouse.
• Check the cable connection.
• Check the mouse with another application to see if there is a software
incompatibility problem.
• If possible, check the mouse with another computer to see if it works. If it doesn’t
operate on a different system, the mouse might be broken.
86
Page 99
Contacting Your Dealer
If you still have a problem after reading the preceding sections, the next step is to contact
your dealer. Your dealer can determine if the problem is something that requires the
computer to be taken to the shop.
Before you call your dealer, however, prepare the following information:
• How is your computer configured? Your dealer needs to know what peripheral
devices you are using.
• What messages, if any, are on the screen?
• What software were you running at the time?
• What have you done already to try to solve the problem? If you have overlooked a
step, your dealer may be able to solve the problem over the phone.
87
Page 100
88
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.