All Rights Reserved.
The information in this document is subject to change without prior notice in order to
improve reliability, design and function and does not represent a commitment on the
part of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are
reserved. No part of this manual may be reproduced by any mechanical, electronic, or
other means in any form without prior written permission of the manufacturer.
TTrraaddeemmaarrkkss
CardSoft is a trademark of SystemSoft Corporation. AutoCAD and Autoshade are
trademarks of Autodesk, Inc. IBM, OS/2, and VGA are trademarks of International
Business Machines Corp. Lotus, 1-2-3, and Symphony are trademarks of Lotus
Development Corp. Windows, Word, MS-DOS, and Microsoft are trademarks of
Microsoft Corp. VESA is a trademark of Video Electronics Standards Association.
Other product names mentioned herein are used for identification purposes only and
may be trademarks and/or registered trademarks of their respective companies.
LLiimmiittaattiioonn ooff LLiiaabbiilliittyy
While reasonable efforts have been made to ensure the accuracy of this manual, the
manufacturer and distributor assume no liability resulting from errors or omissions in
this manual, or from the use of the information contained herein.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio TV technician for help.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and if not installed and used in accordance with the
instruction manual may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
NNoottiiccee::
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. Shielded
interface cables and a non-shielded AC power cord must be used in order to comply
with emission limits.
This equipment is to be used with power supply:
I/P: 100-240 Vac, 50-60Hz, 1.8A
O/P: 19Vdc, 3.42A
Welcome to the Notebook PC........................................................................................................................12
Getting to Know Your Computer...................................................................................................................12
Chapter 3: Getting Started --------------------------------------------------------25
Connecting to a Power Source....................................................................................................................... 25
Turning On Your Notebook Computer.......................................................................................................... 27
Operating on Battery Power........................................................................................................................... 27
Chapter 4: Using the Notebook Computer ----------------------------------31
Adjusting the LCD Screen Display................................................................................................................ 31
A Tour of the Notebook’s Keyboard ............................................................................................................. 33
The TouchPad................................................................................................................................................ 34
Connecting an External Tracking Devices.....................................................................................................36
The CD-ROM/DVD-ROM/Combo ............................................................................................................... 36
PCMCIA Cards and Expansion Sockets........................................................................................................ 39
Power Saving Modes ..................................................................................................................................... 40
Navigating through BIOS Setup .................................................................................................................... 50
Accessing the BIOS Setup Program .............................................................................................................. 50
5
The Menu Bar ................................................................................................................................................50
The Legend Bar..............................................................................................................................................51
General Help.................................................................................................................................................. 52
The Main Menu .............................................................................................................................................53
The Advanced Menu...................................................................................................................................... 54
The Security Menu......................................................................................................................................... 56
The Boot Menu ..............................................................................................................................................57
The Exit Menu ............................................................................................................................................... 58
Chapter 7: The Software Utilities Disks --------------------------------------59
Locating a Problem........................................................................................................................................ 72
Checking Cables and Connections.................................................................................................................73
The Power-On Self Test................................................................................................................................. 74
General Hardware Problems .......................................................................................................................... 75
Contacting Your Dealer .................................................................................................................................77
Chapter 9: Upgrading your System--------------------------------------------78
Upgrading your Memory ...............................................................................................................................78
The Easy to Upgrade HDD Module............................................................................................................... 80
Upgrading your System CPU......................................................................................................................... 82
Use this manual will help you get the most from your notebook computer.
• If you are an experienced user of computers and/or Microsoft’s Windows operating
systems, you might find it useful to read the Quick Start Guide that comes along
with your accessories.
• If you are a less experienced user, you should through the manual carefully before
using your system.
Whether or not you are an experienced user, you should consult on the
Troubleshooting Chapter if you encounter any problems with your notebook.
1
The check mark symbol indicates that you should take note on every
detailed information when you encounter some function that might be useful
when you are using your notebook.
The pencil symbol identifies information which is important for you to read
to avoid damage to the computer.
This warning cautions you against actions which might be destructive to
your data or might disrupt proper system operation.
SSaaffeettyy PPrreeccaauuttiioonnss
This section is designed to assist you in identifying potentially unsafe conditions while
working with this product. Required safety features have been installed in the
computer to protect you from injury. However, you should use good judgment to
identify potential safety hazards:
Please read these safety instructions carefully.
11..
Please keep this User's Manual for later reference.
22..
Please disconnect this equipment from AC outlet before cleaning. Don't use liquid
33..
or sprayed detergent for cleaning. Use moisture sheet or cloth for cleaning.
For pluggable equipment, that the socket-outlet shall be installed near the
44..
equipment and shall be easily accessible.
Please keep this equipment from humidity.
55..
Lay this equipment on a reliable surface when installed. A drop or fall could cause
66..
injury.
Make sure to use the right voltage for the power source when connecting the
77..
equipment to the power outlet.
2
Place the power cord in such a way that people can not step on it. Do not place
88..
anything on top of the power cord.
All cautions and warnings on the equipment should be noted.
99..
If the equipment is not use for a long time, disconnect the equipment from the
1100..
main power outlet to avoid being damaged by transient overvoltage.
Never pour any liquid into the opening, this could cause fire or electrical shock.
1111..
Never open the equipment. For safety reason, the equipment should only be
1122..
opened by a qualified service personnel.
If on the following situations arises, get the equipment checked by a service
1133..
personnel:
a.
The Power cord or plug is damaged.
b.
Liquid has penetrated into the equipment.
c.
The equipment has been exposed to moisture.
d.
The equipment has not worked well or you cannot get it work according to the
user's manual.
e.
The equipment has dropped and damaged.
f.
If the equipment has obvious sign of breakage.
Do not leave this equipment in an environment unconditioned, storage
1144..
temperature above 60°C (140°f), it may damage the equipment.
The unit can be operated at an ambient temperature of max. 35°C.
1155..
The sound pressure level at the operators position according to IEC 704-1: 1982 is
1166..
equal or less than 70 dB(A).
Power Cord Requirements
1177..
The power cord set used with the AC adaptor must meet the requirements of the
country where you use the AC adaptor, whether it is 100-120 or 200-240 Vac.
The following information explains the requirements for power cord set selection.
• The cord set must be approved for the country in which it is used.
• The appliance coupler must have a configuration for mating with a
CEE22/EN6032/IEC 320 appliance inlet.
3
For U.S. and Canada: A.
• The cord set must be UL Listed and CSA Certified.
• The minimum specifications for the flexible cord are No. 18 AWG.
B.
For Japan:
• All components of the cord set must bear a “PSE” or “ T ” mark and
registration number in accordance with the Japanese Dentori Law.
• The minimum specifications for the flexible cord are .75m ㎡ conductors.
C.
For Other Countries:
• The cord set fittings must bear the certification mark of the agency
responsible for evaluation in a specific country.
• The flexible cord must be of a HAR (harmonized) type H05VV-F.
• The cord set must have a current capacity of a least 2.5 Amperes and voltage
rating of 125 or 250 Vac.
When using your telephone equipment, basic safety precautions should always be
1188..
followed to reduce the risk of fire, electric shock and injury to persons. These
precautions includes the following:
• Do not use this product near water, for example, near a bathtub, washbowl,
kitchen sink or laundry tub, in a wet basement or near a swimming pool.
• Avoid using a telephone (other than a cordless type) during an electrical
storm. There may be a remote risk of electric shock from lightning.
• Do not use the telephone to report a gas leak in the vicinity of the leak.
• Use only the power cord indicated in this manual.
Do not use the AC adapter near open water or other liquids. Never spill liquid into
1199..
the AC adapter.
Laser Warning: Laser Class I Product Caution - Invisible laser radiation when open
2200..
avoid exposure to beam.
Danger of explosion if battery is incorrectly replaced. Replace only with the same
2211..
4
or equivalent type recommended by the manufacturer. Dispose of used batteries
according to the manufacturer's instructions. Never remove the battery pack while
the power is on as this may result in data loss when the system loses power.
The input receptacle is used as the main disconnecting device.
Heben Sie dirse Anleitung für den späteren Gebrauch auf.
22..
Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Versenden Sie Keine
33..
Flüssig- oder Aerosolreiniger. Am besten eignet sich ein angefeuchtetes Tuch zur
Reinigung.
Die Netzanschlusteckdose soll nahe dem Gerät angebracht und leicht zugänglich β
44..
sein.
Das Gerät ist vor Feuchtigkeit zu schützen.
55..
Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen oder
66..
Fallen könnte Beschädigungen hervorrufen.
Beachten Sie beim Anschluß an das Stromnet die Anschlußwerte.
77..
Verlegen Sie die Netzanschlußleitung so, daß niemand darüber fallen kann. Es sollte
88..
auch nichts auf der Leitun abgestellt werden.
Alle Hinweise und Warnungen, die sich am Gerät befinden, sind zu beachten.
99..
Wird das Gerät üeinen längeren Zeitraum nicht benutzt, sollten Sie es vom
1100..
Stromnetz trennen. Somit wird im Falle einer Überspannung eine Beschädigung
vermieden.
Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüssigkeien in das
1111..
Gerät gelangen. Dies könne einen Brand bzw. Elektrischen Schlag auslösen.
Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen
1122..
Sicherheit nur von authorisiertem Servicepersonal geöffnet werden.
Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen und
1133..
von einer qualifizierten Servicestelle zu Überprüfung.:
5
a.
Netzlabel oder Netzstecker sind beschädigt.
b.
Flüssigkeit ist in das Gerät eingedrungen.
c.
Das Gerät war Feuchtigkeit ausgesetzt.
d.
Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioniert oder Sie
mit Hilfe dieser Anleitung keine Verbesserung erzielen.
e.
Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.
f.
Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.
VORSICHT: Explosiongsgetahr bei unsachgemäßen Austausch der Batterie. Ersatz
1144..
nur durch denselben oder einem vom Hersteller empfohlenem ähnlichen Typ.
Entsorgung gebrauchter Batterien nach Angaben des Herstellers.
Dieses Schaltnetzteil kann bis zu einer Außentemperatur von maximal 35ºC.
1155..
Die Ausgangswerte dürfen nicht die auf dem Label angegebenen Werte
1166..
überschreiten.
Anforderungen an das Stromkabel
1177..
Das Kabel-Set, das an das Netzteil angeschlossen wird, muss den Anforderungen
des Landes, in dem Sie das Netzteil einsetzen, genügen, je nachdem, ob die
Netzspannung 100-120 oder 200-240V Wechselspannung beträgt.
• Das Kabel-Set muss für das Land, in dem es eingesetzt wird, zugelassen sein.
• Der Gerätestecker des Kabels muss in eine CEE22/ EN603/ IEC 320 Buchse
passen.
A.
Für die USA und Kanada:
• Das Kabel-Set muss UL-gelistet und CSA zertifiziert sein.
• Die Minimalanforderungen für das Kabel entsprechen No. 18 AWG.
6
B.
Für Japan:
• Alle Teile des Kabel-Sets müssen entsprechend dem japanischen Dentori
Law mit einem „PSE“ or „T”-Symbol markiert sein
• Die Minimalanforderungen für das Kabel sind .75m ㎡ Leiter.
C.
Für andere Länder:
• Die Zubehörteile des Kabel-Sets müssen das Prüfsiegel derjenigen Stelle, die
in dem jeweiligen Land für die Sicherheitsprüfung zuständig ist, tragen.
• Das Kabel muss vom HAR (harmonisierten) Typ H05VV-F sein.
• Das Kabel-Set muss eine Stromkapazität von mindestens 2,5 Ampere haben
und Spannungen von 125 oder 250 V Wechselstrom gestatten.
Bei der Benutzung Ihres Telefongerätes sollten Sie immer die grundlegenden
1188..
Sicherheitsmaßnahmen beachten, um das Risiko von Feuer, Stromschlägen und
Verletzungen zu minimieren. Zu beachten sind u.a. folgende Punkte:
• Benutzen Sie das Gerät nicht in der Nähe von Wasser, wie zum Beispiel
Badewanne, Waschbecken, Spülbecken, Waschbottich, in feuchten
Kellerräumen oder in der Nähe von Schwimmbecken.
• Benutzen Sie kein Telefon (ausgenommen schnurlose Modelle) während
eines Gewitters. Es besteht das geringe Restrisiko eines Blitzschlages.
• Benutzen Sie das Telefon nicht um ein Gasleck zu melden, falls es sich in der
Nähe des Lecks befindet.
• Benutzen Sie nur solch ein Stromkabel, wie in dieser Anleitung beschrieben.
Benutzen Sie das Netzteil nicht in unmittelbarer Nähe zu Wasser oder anderen
1199..
Flüssigkeiten. Gießen Sie nie Flüssigkeiten über das Netzteil.
Achtung Laser: Laser Produkt der Klasse I. Achtung - Unsichtbarer Laserstrahl,
2200..
vermeiden Sie Kontakt mit dem Strahl bei offenem Gehäuse.
Es besteht Explosionsgefahr, wenn der Akku nicht ordnungsgemäß ersetzt wird.
2211..
Ersetzen Sie den Akku nur durch einen Akku gleichen oder äquivalenten Typs, der
vom Hersteller empfohlen wird. Entsorgen Sie Akkus entsprechend den
Anweisungen des Herstellers. Entfernen Sie den Akku auf keinen Fall bei
eingeschaltetem Notebook, da hierdurch Daten verloren gehen könnten.
Der Netzeingabeanschluss dient als Hauptschalter des Geräts.
Your notebook can easily stand temperature extremes but it doesn’t like rapid changes
in temperature, like going from the cold outdoors to a warm office. Rapid changes in
temperature can cause water droplets to condense inside your case, threatening to
damage the electronic parts inside.
After receiving your notebook when it’s hot or cold outside, try not to power up the
computer immediately, let the computer adjust to the room temperature gradually at
least for three to four hours.
If your system arrives in cold weather, do not apply power to the computer
or monitor until they have been allowed to come to room temperature.
Find a suitable place for your computer that’s not too hot, too cold, too dark, or too
bright. Glare can make it hard to read the screen.
• Try to avoid the computer components from being destroyed if it is over heated, so
try to allow plenty of room for air to circulate around the case.
• Do not block the ventilation opening.
• Do not place your computer in direct sunlight.
SSuuiittaabbllee ppllaaccee ttoo wwoorrkk
Your computer will run well wherever you’re comfortable but extremes of
temperature and humidity can be challenging to your system’s parts.
8
There are some things you can tolerate that the computer can’t — things like static
electricity, dust, water, steam and oil. In case you decide to pull over for roadside
computing, try to choose a clean, comfortable work area for your system.
A lithium-ion battery pack will be available when you are traveling. If you are running
your system for the first time on battery power, remove the battery from the package,
install it into the system and recharge the battery to fully prepare for service.
9
Page intentionally left blank
10
IInnttrroodduuccttiioonn
There are more and more people spending large amounts of time in front of
computer monitors now that scientists from many fields including anatomy,
psychology, and occupational safety are involved in the study of ergonomically
sound work environments.
A few tips to help you work effectively without a lot of physical discomfort:
• Purchase a chair with armrests and good back support. Don't slouch when sitting;
keep your back straight.
• Try to place the LCD panel or external monitor so that there is little glare from the
sun on the monitor.
• Walk around the room every hour.
• Every half hour look away from the computer screen for a few minutes.
• Place everything that you need to work within easy reach.
11
WWeellccoommee ttoo tthhee NNootteebbooookk PPCC
Congratulations on your purchase of the Notebook PC. Your Notebook features the
latest advances in portable computing technology. The Notebook’s modular design
provides maximum expandability without compromising portability. The highperformance CPU and enhanced IDE hard drive provides you with extra processing
power for handling complex graphics and running large programs.
One PCMCIA slot gives you the ability to use standard PCMCIA cards, such as a LAN
adapter or memory cards.
At the front of the Notebook you will find a retaining latch on the display panel that
locks the display in closed position when the Notebook is not in use.
12
Slide the display panel latch to the right until the display panel releases, and then
11..
raise the LCD screen.
At any time you can tilt the display toward or away from you to a comfortable
22..
viewing position.
To avoid damage to the display panel:
1. Try not to slam the display upon closing it.
2. Try not to place any object on top when it is closed or open.
3. Be sure the system is turned off or in suspend mode before you close the
display panel.
To shutdown the system in non-Windows (DOS mode, System POST, Setup
Menu or Quick Boot Menu) based environment, enable the lid switch. This
will prevent the system from damaged if it exceeds the temperature limit.
Windows will control the lid switch in windows environment.
With the LCD screen open, you will see several features important for operating your
Notebook computer.
13
p
Each of these features is briefly described below.
LCD Cover Release Latch
11..
Slide this latch to the right to open the LCD cover.
LCD Screen
22..
Your Notebook computer is equipped with a replaceable color Liquid Crystal Display
(LCD) screen that supports up to 1024 x 768 or 1400 x 1050 x 16M LCD resolution
utilizing a AGP BUS.
A built-in backlight allows you to comfortably view the screen even when ambient
lighting is low.
Internet Explorer Button
33..
Use this key to open the Internet Explorer.
Outlook Express Button
44..
Use this key to open Microsoft's Outlook to send/receive your mail.
System Status Indicator Panel
55..
The system status indicator panel keeps you informed of the computer’s operating
status.
Indicates that the computer is accessing the hard disk drive.
Indicates that the keyboard is in Num Lock mode.
Indicates when the keyboard is in Caps Lock mode. In this mode, the
keyboard produces uppercase text when you press a key. When you
ress the Caps Lock key again, the indicator goes off and the keyboard
14
produces lowercase text.
Indicates when the keyboard is in Scroll Lock mode. Some applications will
move information across the screen differently when Scroll Lock is on.
15
Power/Resume Button
66..
Pressing this button for 1-2 seconds will turn on the system or pressing this button
when the computer is in Suspend mode will resume normal operation. Pressing this
button for 4-6 seconds will also turn off the system.
TouchPad
77..
The TouchPad is hardware-compatible with the IBM PS/2 mouse and softwarecompatible with the Microsoft mouse.
TouchPad Buttons
88..
The buttons below the TouchPad correspond to the left and right buttons on a
standard mouse. The PS/2 compatible mouse will work with the Notebook PC’s
TouchPad simultaneously.
Scroll Button
99..
Use this button to scroll up and down the scrolling bar.
The Built-in Microphone
1100..
The built-in microphone is located to the left of the TouchPad.
16
TThhee LLeefftt SSiiddee
Ventilation Opening
11..
Please don’t block this opening during operation of the system.
1394A
22..
A very fast external bus standard that supports data transfer rates of up to 400 Mbps
(400 million bits per second).
17
Can be used to connect up 63 external devices, also supports isochronous data -delivering data at a guaranteed rate. This makes it ideal for devices that need to
transfer high levels of data in real-time, such as video devices. Also supports both
Plug-and-Play and hot plugging, and also provides power to peripheral devices.
PCMCIA Socket Cover
33..
Open this cover to access the PCMCIA socket. The computer’s PCMCIA socket lets
you extend the capabilities of your computer by inserting PC cards.
PCMCIA Socket Button
44..
The computer has one PCMCIA type II socket
The LAN Port
55..
This jack provides a standard RJ-45 connection for integration with an existing
network or a high-speed (DSL or cable) connection via a network cable.
When using a LAN, please use an EMI Shielding Cable to minimize an
inteference when transmitting.
The Modem Port
66..
18
This jack is an internal 56K voice/fax/data modem. You will connect your computer to
your phone line through this port.
Always disconnect all telephone lines from the wall outlet before servicing
or disassembling this equipment. To reduce the risk of fire use only No.
26 AWG or larger telecommunication line cord.
Microphone Jack
77..
Allows you to receive monophonic input from an external microphone. Use of an
external microphone will disable the built-in microphone.
Audio Line Out Jack
88..
You can plug an external speaker, headphone or connect the line out jack to an audio
device such as a cassette recorder to record the notebook's audio output.
LLEEDD IInnddiiccaattoorrss
These three LED indicators are
separately program for the
following functions: Power On,
Suspend Mode and Battery
Charge.
Power On
11..
This indicator will lit when
the notebook is powered
On.
Battery Charge
22..
This indicator will lit green when the battery is in charging status. When the indicator
light turns off, it indicates the system is in full charge.
Suspend Mode
33..
This indicator will lit when the notebook enter the suspend mode.
19
TThhee RRiigghhtt SSiiddee
20
The CD-ROM/DVD-ROM or DVD CD-RW Combo (Option)
11..
Your Notebook comes with a swappable 24X (or higher) 5.25" IDE CD-ROM or 8X
DVD-ROM.
DC IN Connector
22..
Plug the AC adapter into this connector.
TThhee RReeaarr
Ventilation Opening
11..
Please don't block this opening during operation of the system.
21
Kensington Lock
22..
Allows you to connect a special computer lock to secure your system.
You can purchase a lock at most computer retailers.
S-Video Port
33..
Allows you to connect any S-Video ready television to your system. You can display
output simultaneously on both the LCD and the television or toggle between the two
screens.
Parallel Port
44..
This port allows you to easily connect a parallel printer or plotter using this 25-pin bidirectional female port.
External CRT Port
55..
This port allows you to easily connect an external VGA/SVGA display monitor into
your Notebook using the 15-pin female connector.
Infrared Data Port
66..
The Infrared Data Port allows your Notebook to become truly wireless.
You can use this port to transfer large amounts of data very quickly to any other
machine (Notebook computers, printers, etc.), which is also equipped with an IrDAcompliant IR port.
This allows you to print documents without any inconvenient cable hookups.
22
USB Ports
77..
Your computer includes two Universal Serial Bus (USB) port. USB is the latest
development in Plug and Play technology. It will eventually replace the need for
separate connectors for external keyboards, serial ports, and parallel (printer) port.
This compartment can be used to extend the capabilities of your system by providing
a connection with various extension card.
23
Battery Release Latch
22..
Lift up this latch to release the battery from its bay.
Expansion Compartment
33..
This compartment will serve as an expansion to upgrade your RAM module.
Battery
44..
Your notebook comes equipped with a factory-installed battery pack module. After
the battery runs down, the module can be removed and replaced with a charged
battery.
Hard Disk Drive
55..
Your computer includes a 2.5-inch IDE hard disk drive (9.5mm in height). The
notebook PC's BIOS automatically detects IDE drive types.
24
Geettttiinngg SSttaarrtteedd
G
CCoonnnneeccttiinngg ttoo aa PPoowweerr SSoouurrccee
CCoonnnneeccttiinngg tthhee AACC AAddaapptteerr
A universal AC adapter is provided to supply your computer with power and also
charge the computer’s battery pack.
The adapter’s AC input voltage can range anywhere from 100 to 240 volts, covering
the standard voltages available in almost every country.
The power cord for the AC adapter requires a three-hole grounded AC outlet. To
connect the computer to an external power source:
25
g
Plug the AC adapter’s connector into the DC-IN connector on the rear of the
11..
computer.
Connect the power cord to the AC adapter and then to a wall outlet.
22..
The best kind of AC power source to connect your Notebook to is a UPS
(Uninterruptible Power Supply). Lacking this, use a power strip with a builtin surge protector. Do not use inferior extension cords as this may result in
damage to your Notebook. The Notebook comes with its own AC adapter.
Do not use a different adapter to power the computer and other electrical
devices.
Whenever possible, keep the AC adapter plugged into the Notebook and an electrical
outlet to recharge the battery.
Never turn off or reset your Notebook while the hard disk is in use and the
HDD status icon is lit; doin
Always wait at least 5 seconds after turning off your Notebook before
turning it back on; turning the power on and off in rapid succession can
damage the Notebook’s electrical circuitry.
so can result in loss or destruction of your data.
Turn on your Notebook by pressing the power button. Hold the button down for a
second or two and release. The Power-On Self Test (POST) runs automatically.
After the POST is completed, the computer reads the operating system from the hard
disk drive into computer memory (this is commonly referred to as “booting” a
computer). If your OS (Operating System such as Windows ME, Windows 2000….
etc) is installed, it should start automatically.
To turn the Notebook off, save your work and close all open applications, click on Start,
then Shu
power button for 4-6 seconds.
OOppeerraattiinngg oonn BBaatttteerryy PPoowweerr
Your computer comes with a rechargeable battery pack that lets you operate the
computer without an external power source. When the battery pack is fully charged,
you can operate the computer for approximately 2 hours under the following
conditions:
• The battery pack initially has a full charge.
t Down and select Shut down the computer and click "Yes" or press the
• No peripheral devices are installed.
• The disk/CD-ROM drives run no more than 10% of the time.
Only use batteries that are approved by an authorized dealer. All batteries
are not the same and therefore should not be treated as such. Using the
wrong battery could cause serious damage to your computer and yourself
through toxic emissions.
The battery pack should already be inserted in your Notebook computer when you
unpack it. If not inserted, follow these directions:
Turn over the notebook with the front of the unit facing you and place it on a solid,
11..
flat surface.
Angle the battery into the bay. The front edge of the battery should slide into the
22..
grooves in the system case.
Gently lower the battery into the bay and push it until it clicks securely in the bay.
33..
To remove the battery pack:
Turn off the notebook, and disconnect the AC adapter. Close the LCD panel and
11..
turn it over and place it on a solid, flat surface.
Lift the release latch to release the battery from the bay. At this time the battery
22..
will now be angled slightly out of the bay.
28
Hold the battery at the finger grip and lift it out of the compartment.
33..
CChhaarrggiinngg tthhee BBaatttteerryy PPaacckk
The installed battery pack charges automatically any time the computer is connected to
the AC adapter and an external power source. It is a good idea to occasionally
discharge the battery pack fully to preserve its operating performance.
The LCD screen display can be adjusted by the following key combinations.
KEYS FUNCTIONS
[Fn] + [F7] Decreases the brightness level.
[Fn] + [F8] Increases the brightness level.
[Fn] + [F10] Use this key combination to expand your video screen or reset to its
original size.
[Fn] + [F12] This key combination toggles the display between the LCD, CRT,
simultaneous LCD/CRT, TV, simultaneous CRT/TV.
mppuutteerr
31
LLCCDD CCaarree
LCD screens are delicate devices that need careful handling. Please pay attention to
the following precautions:
• When you are not using the computer, keep the LCD screen closed to protect it
from dust.
• If you need to clean your LCD screen, use a soft tissue to gently wipe the LCD
surface.
• Do not put your fingers or sharp objects directly on the surface and never spray
cleaner directly onto the display.
• Do not press on, or store any objects on the cover when it is closed. Doing so
may cause the LCD to break.
EExxtteerrnnaall CCRRTT DDiissppllaayy
You can hook up an external monitor through the 15-pin CRT connector. Three
configurations are available:
• LCD only
• CRT only
• Simultaneous display of the LCD screen and CRT monitor
• TV only
• Simultaneous display of the TV screen and CRT monitor
You can switch between these display configurations by pressing the key combination
[Fn] + [F12]. For information on connecting an external display, please refer to
Chapter Four.
32
AA TToouurr ooff tthhee NNootteebbooookk’’ss KKeeyybbooaarrdd
The Notebook’s keyboard uses a standard QWERTY layout with the addition of special
function keys and an embedded numeric keypad for number intensive data entry. Your
keyboard supports Windows by incorporating the two Windows specific keys.
With the two Windows keys you will be able to access and take advantage of many of
the timesaving features of Windows software.
The function keys (F1-F12) on the top row of the keyboard, serve different purposes
and carry out different tasks depending on the application you are running.
The cursor (arrow) keys (which are all located in the lower right corner of your
keyboard) and the [PgUp], [PgDn], [Home] and [End] keys (which are located along
the right edge of the keyboard) allow you to move the active cursor of the computer
to various locations on the screen or within the document.
The embedded numeric keypad consists of 15 keys that make number intensive input
more convenient. Like the [Num Lock] key, these keys are labeled in blue on the
keycaps. Numeric assignments are located at the upper right of each key.
When the numeric keypad is engaged, the NumLock icon will appear in the System
Window. The keypad is activated by pressing the [Fn] + [NumLk] key. If an external
keyboard is connected, pressing the NumLock key on either the Notebook or external
keyboard will enable/disable NumLock of both keyboards in unison.
To disable the Notebook numeric keypad while keeping the keypad on an external
keyboard activated, use the [Fn] + [NumLk] hot key on the Notebook keyboard.
Power ButtonPress this button once to power on or enter the suspend/resume
mode.
Press this button for more than 4 seconds to power off the system.
Internet
Button
Email Button Open Email Reader short-cut key
[Fn] + [F1] This key combination turns on/off the battery beeping sound
[Fn] + [F2] This key combination turns on/off the volume.
[Fn] + [F3] Decreases the speaker volume.
[Fn] + [F4] Increases the speaker volume.
[Fn] + [F5] Enable/Disable the system Touchpad function
[Fn] + [F7] Decreases the brightness level.
[Fn] + [F8] Increases the brightness level.
[Fn] + [F10] Use this key combination to expand your video screen or reset to
[Fn] + [F12] This key combination toggles the display between the LCD, CRT,
Open Internet WWW Home short-cut key
its original size.
simultaneous LCD/CRT, TV, simultaneous CRT/TV.
TThhee TToouucchhPPaadd
The touchpad is a rectangular electronic panel located just below your keyboard. You
can use the static-sensitive panel of the touchpad and slit it to move the cursor. You
can use the buttons below the touchpad as left and right mouse buttons.
34
TToouucchhPPaadd PPrreeccaauuttiioonnss
The TouchPad is a pressure sensitive device. Please take note of the following
precautions.
• Make sure the TouchPad does not come into contact with dirt, liquids or grease.
• Do not touch the TouchPad if your fingers are dirty.
• Do not rest heavy objects on the TouchPad or the TouchPad buttons.
You can use the TouchPad with Microsoft Windows as well as non-Windows
applications.
The system will only enables you to use one tracking device whether it is an internal or
external tracking device.
DDaattaa SSttoorraaggee aanndd RReettrriieevvaall
Data storage and retrieval are two of the most fundamental tasks you will perform
when working with your computer. The Notebook is equipped with a hard disk drive
(HDD). The HDD is removable allowing for easy upgrades.
• Always hold the disc by the edges, avoid touching the surface.
• Use a clean, dry, cloth to remove dust, smudges, or fingerprints. Wipe from the
center outward.
36
• Do not write or place objects on the surface of the disc.
• Store discs in a cool dry place not to damage the disc.
• Do not use benzene, thinners, or cleaners with detergent. Only use CD-
ROM/DVD-ROM cleaning kits.
• Do not bend or drop the discs.
LLooaaddiinngg aa DDiisscc
To play a CD disc, follow the instructions listed below.
Push the CD-ROM/DVD-ROM/Combo eject button on the CD drive door.
11..
Gently pull the tray all the way out.
Carefully lift the CD-ROM/DVD-ROM/Combo by the edges and make sure the
22..
shiny surface is face down (the side with no writing on it). Carefully insert the CDROM onto the tray. Push the CD-ROM/DVD-ROM down gently so that it snaps
onto the center ring.
Push the tray back into the drive.
33..
To remove a disk, do the following:
Check the LED display and make sure that the computer is not accessing the CD-
11..
ROM/DVD-ROM drive.
Push the eject button and pull the tray all the way out.
22..
Carefully pick up the CD disk by the edges and — while pressing down on the
33..
center ring — remove the CD-ROM/DVD-ROM/Combo from the tray.
37
38
Do not insert any foreign objects into the disc tray. If you experience
difficulty when ejecting the CD disk tray, stretch a paper clip (or use a pin or
a thin metal rod) and insert it into the emergency eject hole located on the
right side of the front panel. The CD disk tray should eject immediately.
This procedure can also be used to remove a CD from the drive when the
Notebook is powered off.
The Notebook features one PCMCIA expansion socket design to interface with one
Type II card.
IInnsseerrttiinngg aa PPCCMMCCIIAA CCaarrdd
The computer will emit a medium tone followed by a high tone when a PC card is
inserted. When you eject a card, the computer will emit a high tone followed by a
medium tone. You can insert and remove a PC card whether the computer is turned
On or Off.
Follow these instructions to insert a PCMCIA card:
Hold the PCMCIA card with the arrow side up and the connector side toward the
11..
socket.
Align the card connectors with the socket and carefully slide into the socket until it
22..
locks into place. The system will beep once to indicate that it has detected the PC
card.
To remove a PC card push the eject button, the button will pop out, push the button
again to eject the PCMCIA.
When inserting a Type II PC card, make sure the connector is inserted in the
socket. Before ejecting a PC card, ensure that it is not being accessed by the
System.
For example, if the message “Write protect error writing Drive x” is
displayed, the user has to change the write protect switch setting on the
memory card. To change the switch setting, (a) eject the card, (b) chan
switch setting, and (c) re-insert the card.
e the
39
Always disconnect all telephone lines from the wall outlet before servicing or
disassembling this equipment. To reduce the risk of fire, use only No. 26
AWG or larger telecommunication line cord.
PPoowweerr SSaavviinngg MMooddeess
This section contains information on the Notebook’s power system, including the AC
Adapter, the battery system, recharging the battery, and tips for conserving battery
power.
The power system is comprised of two parts, the AC Adapter and the battery system.
The AC Adapter converts AC power from a wall outlet to the DC power required by
the computer.
TThhee BBaatttteerryy PPoowweerr SSyysstteemm
A fully charged pack will provide approximately 2 hours of battery life depending on
your system configuration application it runs.
Before using the computer on battery power for the first time, check the battery status
icon on the Windows Toolbar to make sure the battery is fully charged.
See Battery Status later in this section for a description and explanation of the
Windows Battery icon. Charging the battery takes about 3 hours to charge when the
system is in off state. If possible, always charge the battery completely.
RReemmoovviinngg tthhee BBaatttteerryy PPaacckk
To remove the battery pack from its compartment, please refer to Chapter 3, Inserting
and Removing the Battery Pack.
Before using the battery pack for the first time, the Smart Battery IC within the battery
pack should be calibrated in order to get accurate reporting of remaining battery life
status.
To calibrate the battery pack follows the instructions below:
Insert the battery into the battery compartment and turn on the Notebook. If the
11..
battery is completely without power go to the next step.
Otherwise, let the battery run down until the battery low-low warning beeps are
heard.
The system will automatically enter Suspend mode.
Turn the Notebook off. Connect the AC adapter and let the battery fully recharge.
22..
When the battery charge indicator turns off, the battery is fully charged.
Turn On the notebook, let the battery run down until the battery is in low-low
33..
state and you hear a warning beeps. The system will automatically enter the
Suspend mode. You can now connect the AC adapter.
The battery pack is now calibrated properly.
44..
In general, using the battery until the low-low battery-warning indicator appears and
fully recharges the battery each time (full discharge/charge cycle) will ensure the
accurate reporting of the battery gauge status.
You can automatically charge the battery pack by using the AC Adapter. The charge
time is about three hours when the Notebook power is turned off. The following
table summarizes the charging modes:
41
Charge Mode Charge Time
Fast 3 hours with the system off or in Suspend mode. The temperature
must be 25°C or below room temperature.
Pre-Charge A pre-charge is supplied to the Li-Ion battery pack.
BBaatttteerryy SSttaattuuss
Windows 2000/XP has an applet in the Control Panel that will display an icon in the
Windows taskbar indicating when the Notebook is running on battery power or is
attached to the AC adapter.
This applet also displays a meter that indicates how much charge is remaining in the
battery.
BBaatttteerryy LLooww WWaarrnniinngg
When the pack initially reaches the “Battery Low” state approximately 10 ~ 15 minutes
of the usable battery life is left.
You will hear an audible beep signal every 1.5 seconds alerting you to the “Battery
Low” status. When the battery power reaches the “Battery Low Low” status the
beeping sound will accelerate.
Your battery now has 1 ~ 2 minutes of battery charge remaining. You must save your
data or connect AC power immediately; otherwise, you may lose your data.
Sound Meaning
Continuous
beeping every 1.5
seconds
Battery Low: Indicates that there is 7 to 10 minutes charge
remaining.
42
Beeping
accelerates
Battery Low Low: Indicates that there is 1 to 2 minutes of
battery charge remaining. Save your work and turn off the
Notebook, or connect the AC adapter.
When there is only one minute of battery charge remaining, the Notebook will
suspend to the HDD and power off. You should connect AC power and resume to
save your work.
There is a small built-in battery pack that supplies power to the system in order to
maintain certain system information while the power is off. If the Notebook is left
without a power source for long period of time, this battery will be exhausted and
system information will be lost.
Danger of explosion if battery is incorrectly replaced. Replace only with the
same or equivalent type recommended by the manufacturer. Dispose of
used batteries according to the manufacturer's instructions. Never remove
the battery pack while the power is on as this may result in data loss when
the system loses power.
RReesseettttiinngg tthhee SSyysstteemm
After installing a software application package, you may be prompted to reset the
system to load the changed operating environment. To reset the system, or “reboot,”
press the [Ctrl] + [Alt] + [Delete] keys simultaneously. This is known as “warm boot.”
This key combination acts as “software” reset switch when you encounter hardware or
software problems, which lock up the Notebook.
If this key combination does not shut down the Notebook, you can reset the
Notebook by using the Notebook’s power button. Should the Notebook lock up for
some reason, pressing this button powers the Notebook off.
43
AAddjjuussttiinngg tthhee BBrriigghhttnneessss
To adjust the brightness on the LCD screen, press and hold down the [Fn] key in the
lower left hand corner of the keyboard and press the [F7] key to reduce the brightness
or [F8] to increase the brightness.
44
Deesskkttoopp
D
Your notebook is capable of providing you with efficient and productive mobile
computing, it also has the speed and capacity to service as a desktop system.
This chapter discusses those functions of your notebook that are typical of desktop
systems.
The Notebook’s built-in audio capabilities allow you to take advantage of a wide range
of education and entertainment multimedia software. The Notebook is equipped with
two internal stereo speakers, a microphone, and input audio ports for external audio
units.
Oppeerraattiioonn
O
45
An external microphone can be connected to the microphone jack. External speakers
or headphones can be connected to the Notebook’s audio-out jack.
External audio devices can be connected to the Line in jack. All audio features are
software controlled. The Notebook’s multimedia sound system includes the following
features:
• Supports Windows Sound System compatibility
• Full Duplex operation
• Dynamic filtering reduces noise and distortion rate
• 16-bit digitized audio playback
• A built-in microphone for convenient recording
• Two built-in stereo speakers
• Digitized audio recording through the Notebook’s built-in microphone or any
external source
AAuuddiioo VVoolluummee CCoonnttrrooll
The Notebook is equipped with hot-key volume controls: Pressing the [Fn] + [F3] hotkey combination decreases the audio output volume, press the [Fn] + [F4] hot-key
combination increases the audio output volume.
AAuuddiioo SSooffttwwaarree
Your notebook comes equipped with an integrated sound system capable of providing
you with quality audio sound through the built-in speakers or through external speakers
connected via the system ports.
46
y
SSoouunndd RReeccoorrddiinngg
Your system allows you to record sounds and store them as files using the microphone
via the microphone jack on the rear of the notebook computer. Check the Windows
Help and Support Center in Windows for information on using the various elements in
sound recording.
For a high-quality sound, click on the "Volume Control" at the lower right end
of
tab, click and select the "Microphone Boost" item.
PPllaayyiinngg SSoouunndd FFiilleess
Your notebook can play audio files stored in MIDI, WAVE or MP3 file format. Check
the Help and Support Center in Windows for information on the functions of the
Media Player.
The sound system is capable in providing high-quality sound to external speakers and
receiving and processing sounds from an external microphone or external sound
source.
our screen. From the Volume Control windows, click on the "Advanced"
To expand your computing capabilities, you can add a variety of external devices to
your computer. You may, for example, want to add a mouse, modem, or a printer.
The computer is equipped with several interface ports, including an enhanced parallel
(printer) port, a serial port, and USB ports. These are provided as a means of
connecting peripheral devices to the computer.
Connect peripheral devices to the computer's interface ports as shown below:
47
48
RRuunnnniinngg BBIIO
IInnttrroodduuccttiioonn
The BIOS (Basic Input and Output System) Setup program is a menu driven utility that
enables you to make changes to the system configuration and tailor your system to
reflect installed hardware or alter system performance. When the Notebook is turned
back on, the system is configured with the values stored in CMOS. With easy-to-use
menus, you can configure such items as:
• Hard drives and peripherals
• Bootup Drive Sequence
• Password protection
OSS SSeettuupp
49
The settings made in the BIOS Setup program intimately affect how the Notebook
performs.
The Setup program has been designed to make it as easy to use as possible. If you
accidentally make a setting and don’t know which one to switch back to, the Setup
program has a hot key that allows you to return to the previous value.
To access the BIOS Setup program, press the DEL key after the Notebook has run
through its POST.
IItteemm SSppeecciiffiicc HHeellpp
On the right side of the Setup screen is an area labeled Item Specific Help. This area
will list navigation key shortcuts and information that is specific for the item that you
are currently editing.
TThhee MMeennuu BBaarr
The top of the screen has a menu bar with the following selections:
Main - Use this menu to make changes to the basic system configuration.
Advanced - Use this menu to enable and make changes to the advanced features
available on your system, such as enabling the FIR module.
Security - Use this menu to set a password. The password allows bootup and controls
access to the BIOS setup menu.
50
Boot - Use this menu to configure the default system device used to locate and load
the Operating System and for booting up the Notebook.
Exit - Use this menu to exit the current menu or specify how to exit the Setup
program.
To access the menu bar items, press the right or left arrow key on the keyboard until
the desired item is highlighted.
TThhee LLeeggeenndd BBaarr
At the bottom of the Setup screen you will notice a legend bar. The keys in the legend
bar allow you to navigate through the various setup menus.
The following table lists the keys found in the legend bar with their corresponding
alternates and functions.
Legend Key Function Legend Key Function
+/−
PGDN or
Home
F2/F3 Change colors F7 Discard change
F8 Load Failsafe defaultF9 Load optimal default
F10 Save and Exit ESC Exit
LLaauunncchhiinngg SSuubbmmeennuuss
Note that a right pointer symbol X appears to the left of certain fields. This pointer
indicates that a submenu can be launched from this field.
Select Screen
Change option/FieldEnter Go to sub screen
Go to top of screenPGUP or End Go to bottom of screen
↑↓
Select Item
51
A submenu contains additional options for a field parameter.
To call up a submenu, simply move the cursor to highlight the field and press the [Enter]
key. Use the [Esc] key to return to the Main menu.
GGeenneerraall HHeellpp
In addition to the Item Specific Help window, the BIOS Setup program also provides a
General Help screen can be called up from any menu by simply pressing [F1] or the
[Alt] + [H] combination.
Use the [PgUp] and [PgDn] keys or the up and down arrow keys (↑↓) to scroll
through the entire help document. Press the Home key to display the first page, press
End to go to the last page. To exit the help window, press the [Enter] or the [Esc] key.
Refer to the Exit menu section of this chapter for detailed information on saving
changes and exiting the setup program.
52
TThhee MMaaiinn MMeennuu
When the Setup program is accessed, the following screen appears:
SSyysstteemm TTiimmee
Sets your system to the time that you specify. The format is hour, minute, second.
Use the [Tab] or [Shift] + [Tab] keys to move between the hour, minute, and
second fields.
53
SSyysstteemm DDaattee
Sets your system to the date that you specify (usually the current date). The format
is month, day, year. Use the [Tab] or [Shift] + [Tab] keys to move between the
month, day, and year fields.
TThhee AAddvvaanncceedd MMeennuu
Selecting Advanced from the menu bar displays the Advanced menu:
54
SSuuppeerrIIOO CCoonnffiigguurraattiioonn
Use this setting to configure your SuperIO Chipset.
QQuuiicckk BBoooott
Allows BIOS to skip certain test while booting. This will decrease the time needed
to boot the system
The configurations are: Disabled or Enabled (default value)
QQuuiieett BBoooott
Disabled: Displays normal POST messages. Enabled: Displays OEM Logo instead of
POST messages.
The configurations are: Disabled (default value) or Enabled
PPSS//22 MMoouussee SSuuppppoorrtt
Use this setting to select support for PS/2 mouse.
The configurations are: Disabled or Enabled (default value)
LLeeggaaccyy UUSSBB SSuuppppoorrtt
Enables support for legacy USB. Auto legacy support if no USB devices are
connected.
The configurations are: Disabled, Enabled (default value) or Auto
LLiidd SSwwiittcchh CCoonnttrrooll
LCD backlight will be turn off when activated otherwise no action.
The configurations are: Disabled or Enabled (default value)
55
TThhee SSeeccuurriittyy MMeennuu
The Notebook’s advanced system of security allows you to set a password to prevent
unauthorized access to system resources, data, and the BIOS Setup Program.
56
TThhee BBoooott MMeennuu
The Boot menu allows the user to specify the order in which the Notebook is to check
for a device to boot the system. You can also configure the way that the system will
boot up.
To make changes, select Boot from the menu bar. The following screen appears:
57
TThhee EExxiitt MMeennuu
Once you have made all of your selections from the various menus in the Setup
program, you should save your changes and exit Setup. Select Exit from the menu bar
to display the following menu:
58
TThhee SSooffttw
AAuuttooRRuunn IInnssttaallllaattiioonn
Follow the step-by-step procedures on the CD-ROM/DVD-ROM to execute the
“AutoRun” application by selecting the topic of “Driver Installation”.
If you encounter this message when executing the Auto Run in Windows
2000, please perform the following procedures:
waarree
Uttiilliittiieess
U
Diisskkss
D
59
Click on the “Start” — “Setting” — “Control Panel” — “System” — “Advanced”
tab — “Performance” tab — “Change” tab — reduce the maximum Virtual
Memory setting to 200MB.
This section describes the operation and installation of VGA display software drivers
supplied on the Driver Utility CD-ROM that is shipped with your computer.
• Insert the CD-ROM Driver into your CD-ROM/DVD-ROM drive.
• Click “Start” and Select “Run”.
• Type the following: D:\Driver\VGA\Setup.exe (If D is not your CD-ROM/DVD-
ROM drive, substitute D with the correct drive letter).
• Click on “Setup” to begin the Installation Wizard.
• Follow the Wizard’s on-screen instructions to complete the installation.
After you have restarted Windows, open the “Control Panel” and double click on the
“Display” icon. From the “Display Properties” window, select the “Settings” tab and
click on the “Advanced” tab to enter the “Default Monitor and MOBILITY RADEON
9600 Properties" window.
65
You will notice there are numerous options included in the Display Properties window:
Displays, color, OpenGL, Direct 3D, Overlay and Options.
66
CCoolloorr
You can adjust the right resolution for your screen display.
67
OOppeennGGLL
Play the latest and greatest OpenGL based games as well as CAD/Design programs.
68
DDiirreecctt 33DD
An API for manipulating and displaying 3-dimensional objects.
69
OOppttiioonnss
Display all the items concerning the ATI related function.
70
OOvveerrllaayy
71
TTrroouubblleesshhoooottiinngg
This chapter describes locating and solving problems that you may encounter while
using your computer.
LLooccaattiinngg aa PPrroobblleemm
Problems with your computer can be caused by something as minor as an unplugged
power cord — or as major as a damaged hard disk. The information in this chapter is
designed to help you find and solve minor problems. If you try all the suggested
solutions and you still have a problem, make a list of what steps you have taken to
correct the problem and contact your dealer.
Successful troubleshooting is the result of careful observation, deductive reasoning, and
an organized approach to solving the problem.
The problems that you will encounter can be divided into two basic categories:
hardware problems and software problems. Hardware problems can be further divided
72
into electrical and mechanical problems. You will know you have a hardware problem if
the screen is dark, the computer cannot read the disk drives, or you get an error
message during the Power-On Self Test (POST).
Software errors can occur at several levels. The ROM BIOS and the operating system
can give you a large number of error messages. On top of this, each application
software package has its own set of error messages. It is important to determine
whether the software error message you are getting is from the application or the
operating system. Once you know this, you can look in the respective manual for a
solution to the problem.
Start by performing a careful visual inspection of the exterior of the computer. If no
LEDs are illuminated, make sure that your computer and its peripherals are getting power
and communicating with each other properly.
To check the power cables, and connections:
If you have been using battery power, connect the Notebook to an external power
11..
source and make sure that the battery has a charge.
If you are using the Notebook with the AC adapter, check the power outlet, the
22..
power cord, and any power switches that may affect your computer.
• Check the wall outlet or power strip with an item that you know is
functioning properly. A lamp or radio is a convenient item for checking the
power. You may also need to check the fuses and breakers in your electric
box.
• If the outlet is controlled by a wall switch, make sure that the switch is on.
• If the outlet is controlled by a dimmer switch, use a different outlet.
• If your computer is plugged into a power strip with an On/Off switch, make
sure the switch is on.
73
With the computer’s power switched off, check all cable connections. If the
33..
computer is connected to any peripheral devices, look for loose or disconnected
cables.
If the computer is too close to a wall, a cable connection may be loose or the cables
may be crimped.
Do not substitute cables for different devices (other than the manufacturer
recommended cables) even if they look exactly alike. The wiring inside the
cable may be different.
When you are certain that you have power available and all connections are good,
44..
turn the computer on again. If the computer still does not start, you may have a
hardware problem.
TThhee PPoowweerr--OOnn SSeellff TTeesstt
The Power-On Self Test (POST) runs every time you turn on or reset the Notebook.
The POST checks memory, the main system board, the display, the keyboard, the disk
drives, and other installed options.
A few seconds after you turn on your computer, a copyright message appears on your
display screen. A memory test message appears next; as the test continues, memory
size increases until all installed memory is tested. Normally, the only test routine visible
on the screen will be the memory test.
Two classifications of malfunctions can be detected during the POST:
• Error messages that indicate a failure with either the hardware, the software, or the
Basic Input/Output System (BIOS). These critical malfunctions prevent the computer
from operating at all or could cause incorrect and apparent results. An example of
a critical error is microprocessor malfunction.
• Messages that furnish important information on the power-on and boot processes
(such as memory status). These non-critical malfunctions are those that cause
74
incorrect results that may not be readily apparent. An example of a non-critical
error would be a memory chip failure.
In general, if the POST detects a system board failure (a critical error), the computer
halts and generates a series of beeps. If failure is detected in an area other than the
system board (such as the display, keyboard, or an adapter card) an error message is
displayed on the screen and testing is stopped. It is important to remember that the
POST does not test all areas of the computer, only those that allow it to be
operational enough to run diagnostic programs.
If your system does not successfully complete the POST, but displays a blank screen,
emits a series of beeps, or displays an error code, consult your dealer.
GGeenneerraall HHaarrddwwaarree PPrroobblleemmss
A few common hardware problems and suggested solutions are presented in the table
below:
Problem:
Solution:
Failure in the installation of the Audio driver.
Be sure to first remove the current audio device from your system. Please
follow the instruction on the installation of audio driver.
Problem:
Solution:
The display screen is dark
Make sure that the computer is not in Suspend mode. Check the Brightness
controls for the screen. If the controls are turned too far down, the screen will be dark.
Problem:
Solution:
An incorrect date and time are displayed.
Correct the date and time using the DOS DATE and TIME commands or the
options in the Setup Utility. If the date and time become incorrect after a short time, your
CMOS battery may be depleted. Contact your dealer to change the battery.
75
Problem:
The message: “Invalid system disk, Replace the disk, and then press any key”
appears during boot.
Solution:
Check and make sure that you do not have a non-bootable floppy diskette
inserted in your floppy drive. If your USB FDD is empty, you may not have an operating
system installed on your drive. Contact technical support for assistance.
Problem:
You hear irregular beeps during operation of the Notebook and the system
halts.
Solution:
Problem:
Solution:
The problem is beyond the scope of this manual. Contact technical support.
An unidentified message is displayed.
Reboot the computer and run the BIOS system setup. Confirm the Setup
parameters. If the same message is displayed after booting up again, contact technical
support for assistance.
Problem:
Solution:
The system cannot access the CD-ROM/DVD-ROM drive.
Check that a CD is properly inserted in the drive. Make sure that you are using
the correct program for that kind of CD. For example, the system cannot read a data CD
using an audio program.
Problem:
Solution:
You cannot operate the printer.
Check the printer cable connection. Ensure that the printer power switch is
turned on. Confirm that the printer is on-line.
Problem:
Solution:
You can’t save data to disk.
Ensure that the disk has been formatted.
Consult your operating system manual for information on formatting floppy diskettes.
76
Problem:
Solution:
Problem:
Solution:
The diskette is write-protected.
Eject the diskette, remove the write protection, and try again.
The diskette if full.
Try using another diskette or free up some space on the diskette. The disk
drive is not operating. Contact your dealer for support.
Problem:
You cannot use the mouse.
• Check the cable connection.
• Check the mouse with another application to see if there is a software
incompatibility problem.
• If possible, check the mouse with another computer to see if it works. If it
doesn’t operate on a different system, the mouse might be broken.
CCoonnttaaccttiinngg YYoouurr DDeeaalleerr
If you still have a problem after reading the preceding sections, the next step is to
contact your dealer. Your dealer can determine if the problem is something that
requires the computer to be taken to the shop. Before you call your dealer, however,
prepare the following information:
• How is your computer configured? Your dealer needs to know what peripheral
devices you are using.
• What messages, if any, are on the screen?
• What software were you running at the time?
• What have you done already to try to solve the problem? If you have overlooked a
step, your dealer may be able to solve the problem over the phone.
77
Uppggrraaddiinngg yyoouurr SSyyssttee
U
UUppggrraaddiinngg yyoouurr MMeemmoorryy
Refer to the following instructions and illustration for information on upgrading your
notebook's memory.
m
m
78
Turn off the computer and disconnect the AC adapter and all peripherals.
11..
Turn the notebook over so that the rear ports are facing you and locate the
22..
memory module compartment.
Remove the screws that secure the RAM module compartment cover and set it
33..
aside in a safe place.
Remove the compartment cover and then angling it up and out.
44..
If you need to install a higher capacity module, gently push the edge clips on both
55..
sides to release the module. Angle the card slightly upward and gently slide it from
its edge connector slot. Store the card in the anti-static bag that contains your new
module(s).
To install the new memory card, hold the card with its gold edge connector toward
66..
the edge connector slot of the compartment. To help you orient the cards, the
edge connector has been made with two unequal-length sections. You will only be
able to insert the card in one direction.
79
Insert the edge connector into the slot. The gold edge connector of the card
77..
should not be visible when the card is fully inserted.
Press the card downward where you should hear an audible click as the latches of
88..
the connector secure the card in place.
Once the module is properly seated, you can replace the cover on this
The hard drive in your notebook computer is made to be easily swapped out for
upgrading. You should back up your hard drive before attempting o change the hard
drive.
Make sure that before you install a new drive, all the files in your system
should be backed up.
80
TToo uuppggrraaddee yyoouurr HHaarrdd DDrriivvee
Power down the system completely. Turn the system over with the front of the
11..
unit facing you.
81
Remove the three screws that secure the compartment cover and set them in a
22..
safe place.
Slide the HDD cover away from the compartment.
33..
The drive is attached to a special bracket that secures it to the notebook computer.
44..
There are 4 screws hold the bracket. Remove the screws and set them in a safe
place.
Push the HDD slightly in the direction of the arrow as shown in the illustration to
55..
release it from the pins of the drive.
Gently hold the grip of the HDD, lift it up to release from its compartment.
66..
To install the new HDD, you will need to align the tabs on the drive bracket with
77..
the slots on the bay. Press down gently on the drive bracket until it engages with
the system. Do not force the drive into place this can bend the pins on the hard
drive.
Slide the compartment cover into place and be sure the screw holes on the cover
88..
align completely with the screw holes in the case.
Secure the cover with the three screws.
99..
UUppggrraaddiinngg yyoouurr SSyysstteemm CCPPUU
Refer to the following instructions and illustration for information on upgrading your
notebook's CPU
Turn off the computer and disconnect the AC adapter and all peripherals. From
11..
the rear side of your notebook, use your index finger to lift up the hinge cover
attached to the LCD screen.
82
Bend your LCD screen into 90 degree angle then carefully lift up the hinge cover.
22..
Remove the screen that is attached to the keyboard in order to remove the
33..
heatsink on top of the CPU.
83
Remove all the screws attached to the heatsink.
44..
Before removing the screws, there are certain measures to followed in removing
55..
the heatsink
To remove the heatsink, first loosen the screw carefully.
66..
84
After loosening one screw, be certain that the next to be loosen should be the
77..
screw on its adjacent side as shown on the illustration.
Be sure to loosen all the screws first before removing it totally to release
the heatsink. Failure to do so will cause a major damage to the heatsink.
Now you can totally remove all the screws also in that order when you first loosen
Intel Pentium-M processor from 1.3GHz to 1.7GHz, 1M L2 cache
Intel Dothan processor from 1.8GHz to 2.0GHz, 2M L2 cache
Intel ODEM + ICH4-M, support FSB 400MHz
0MB on board, 2 SO-DIMM slots, up to 2GB
Support DDR 266/333MHz system memory
2.5” 9.5mm height, ATA 100/66 supported, up to 7200 rpm
SSppeecciiffiiccaattiioonn
86
Optical Drive
TouchPad
Launch Key
Keyboard
I/O Port
PCMCIA
Audio
AC Adapter
Battery
Battery Charge
Battery Life
BIOS
Communication
5.25”/12.7mm CD-ROM, DVD-ROM, Combo Drive, DVD+RW, DVD
Dual
Synaptics w/ scrolling button (4 ways)
Hot keys: E-mail, internet hot key
88 keys with 12 function keys and 3 Windows keys
2 x USB2.0 ports, parallel port, VGA port, RJ-11, RJ-45, FIR, 1394a, TV-
Out , head phone(SPDIF), Mic_in
Type II PCMCIA slot, support CardBus
AC97 2.1compliant, , 5.1 channel support, built-in two stereo speakers
65 watts, Universal
Li-Ion battery @ 53 Whrs (8 cells)
3 hrs charge time while system off
4 hrs charge time while system on
More than 4.0 hrs
AMI
Support PnP, password
10/100 Base-T LAN on board
MDC Fax/modem V.90/V.92 on board
Size
Weight
Intel PRO/Wireless 2100/2100A ( MiniPCI solution )
326(W) x 258(D) x 25.3(H) mm/32mm (front/back)
2.5kg
87
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.