i
Preface
Copyright 2005
All Rights Reserved.
The information in this document is subject to change without prior
notice in order to improve reliability, design and function and does not
represent a commitment on the part of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special,
incidental, or consequential damages arising out of the use or inability to
use the product or documentation, even if advised of the possibility of
such damages.
This document contains proprietary information protected by copyright.
All rights are reserved. No part of this manual may be reproduced by any
mechanical, electronic, or other means in any form without prior written
permission of the manufacturer.
Trademarks
AutoCAD and Autoshade are trademarks of Autodesk, Inc. IBM, OS/2,
and VGA are trademarks of International Business Machines Corp. Lotus,
1-2-3, and Symphony are trademarks of Lotus Development Corp.
Windows, Word, MS-DOS, and Microsoft are trademarks of Microsoft
Corp. VESA is a trademark of Video Electronics Standards Association.
Other product names mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of
their respective companies.
Limitation of Liability
While reasonable efforts have been made to ensure the accuracy of this
manual, the manufacturer and distributor assume no liability resulting
from errors or omissions in this manual, or from the use of the
information contained herein.
i
Notices
Federal Communications Commission Radio Frequency
Interference Statement
This equipment has been tested and found
to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can
radiate radio frequency energy and if not installed and used in
accordance with the instruction manual may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected
• Consult the dealer or an experienced radio TV technician for help
Notice:
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Shielded interface cables and a non-shielded AC power cord must be used
in order to comply with emission limits.
This equipment is to be used with power supply:
I/P: 100-240 Vac, 50-60Hz, 1.5A min.
O/P: 19Vdc, 3.42A min., 65W
There is no internal power supply.
ii
Table of Content
Chapter 1: Before you Start -------------------------------------------- 1
Safety Compliance Notice ................................................................1
EUROPE – EU DECLARATION OF CONFORMITY...................... 1
Things you must remember before working on your computer .......... 8
Chapter 2: Introduction -------------------------------------------------- 9
Unpacking the Notebook.................................................................. 9
Opening the LCD Panel ................................................................... 9
The Front ......................................................................................... 13
The Left Side ...................................................................................13
The Right Side ................................................................................. 14
The Rear ..........................................................................................14
The Bottom Panel ............................................................................ 15
Chapter 3: Getting Started ---------------------------------------------- 17
Connecting the AC Adapter.............................................................. 17
Turning On Your Notebook Computer.............................................. 18
Operating on Battery Power .............................................................18
Chapter 4: Using the Notebook Computer ------------------------- 21
LCD Care ........................................................................................ 21
The Notebook’s Hot Key Controls.................................................... 22
TouchPad Precautions ...................................................................... 23
Data Storage and Retrieval............................................................... 24
Features of the CD/DVD-ROM Module............................................ 24
Precautions for Handling CD/DVD-ROM/Combo Discs ...................24
The Battery Power System ...............................................................25
Removing the Battery Pack .............................................................. 25
Preparing the Battery Pack for Use ................................................... 26
Battery Calibration........................................................................... 27
Chapter 5: Desktop Operation ----------------------------------------- 29
The Multimedia Sound System.........................................................29
Chapter 6: Configuring & Maintaining Your System ------------ 31
Navigating through BIOS Setup ....................................................... 31
Accessing the BIOS Setup Program.................................................. 31
The Menu Bar .................................................................................. 31
The Legend Bar ...............................................................................32
Launching Submenus ....................................................................... 33
General Help....................................................................................33
iii
The Main Menu ...............................................................................34
The Advanced Menu ........................................................................ 35
The Boot Menu ................................................................................36
The Security Menu........................................................................... 37
The Exit Menu ................................................................................. 38
Chapter 7: VGA Utilities ------------------------------------------------- 39
S3Display ........................................................................................40
S3Gamma Plus................................................................................. 41
S3Info Overlay ................................................................................ 42
Chapter 8: Troubleshooting -------------------------------------------- 43
Checking Cables and Connections ....................................................43
The Power-On Self Test ...................................................................44
General Hardware Problems .............................................................45
Contacting Your Dealer.................................................................... 46
Chapter 9: How do I expand my Notebook ------------------------- 47
How to upgrade your Hard Drive......................................................48
Appendix: Specification ------------------------------------------------- 49
iv
Canadian DOC Notice For Class B Computing Devices
This Class B digital apparatus meets all requirements of the Canadian
Interference - Causing Equipment Regulations.
Cet appareil numerique de la classe B repecte toutes les exigences du
Règlement sur le matèriel brouilleur du Canada.
Personal Inventory
This Notebook computer system is designed for years of productive and
pleasurable computing. Use this section to keep notes about details of
your purchase. Update this section when you add new options.
Date of Purchase:
Dealer’s Name:
Phone:
Address:
E-Mail Address:
WWW Site:
Serial Number:
CPU Type:
Hard Disk Capacity:
Memory Capacity:
Optional Equipment:
v
BEFORE YOU START
Conventions of This manual
Use this manual will help you get the most from your notebook computer.
• If you are an experienced user of computers and/or Microsoft’s
Windows operating systems, you might find it useful to read the
Quick Start Guide that comes along with your accessories.
• If you are a less experienced user, you should through the manual
carefully before using your system.
Whether or not you are an experienced user, you should consult on the
Troubleshooting Chapter if you encounter any problems with your
notebook.
REGULATORY STATEMENT SAMPLE
Safety Compliance Notice
This device has been tested and certified according to the following safety
standards and is intended for use only in Information Technology
Equipment which has been tested to these or other equivalent standards:
• EN 60950-1
EUROPE – EU DECLARATION OF CONFORMITY
Hereby, xxx Corporation, declares that this Product is in compliance with
the essential requirements and other relevant provisions of Directive
1999/5/EC.
EUROPE – RESTRICTIONS FOR USE OF 2.4GHZ FREQUENCIES IN EUROPEAN
COMMUNITY COUNTRIES
This device may be operated indoors or outdoors in all countries of the
European Community using the 2.4GHz band: Channels 1 – 13, except
where noted below.
• In Italy the end-user must apply for a license from the national
spectrum authority to operate this device outdoors.
• In Belgium outdoor operation is only permitted using the 2.46 –
2.4835 GHz band: Channel 13
• In France outdoor operation is only permitted using the 2.4 –
2.454 GHz band: Channels 1 – 7
1
EUROPE – RESTRICTIONS FOR USE OF 5GHZ FREQUENCIES IN EUROPEAN
COMMUNITY COUNTRIES
Allowed
Frequency Bands
5.15-5.25GHz 36, 40, 44, 48 Austria
5.15-5.35GHz 36, 40, 44, 48,
5.15-5.35 & 5.470-
5.725GH z
Allowed
Channel
Numbers
52, 56, 60, 64
36, 40, 44, 48,
52, 56, 60, 64,
100, 104, 108,
112, 116, 120,
124, 128, 132,
136, 140
Countries
Cyprus, Czech
Republic, France,
Hungary, Slovakia
Belgium, Bulgaria,
Denmark, Estonia,
Finland, Germany,
Greece, Iceland,
Ireland, Italy, Latvia,
Liechtenstein,
Lithuania,
Luxembourg, Malta,
Netherlands, Norway,
Poland, Portugal,
Slovenia, Spain,
Sweden, Switzerland,
U.K.
• This device may not be operated outdoors when using the bands
5150-5350MHz (Channels 36, 40, 44, 48, 52, 56, 50, 64).
• In Italy the end-user must apply for a license from the national
spectrum authority to operate this device outdoors.
• To remain in conformance with European spectrum usage laws for
Wireless LAN operation, the above 5GHz channel limitations apply.
The user should check the current channel of operation. If
operation is occurring outside of the allowable frequencies as listed
above, the user must cease operating at that location and consult
the local technical support staff responsible for the wireless
network.
• The 5GHz Turbo mode feature is not allowed for operation in
any European Community country
• This device must not be operated in ad-hoc mode using channels
in the 5GHz bands in the European Community. Ad-hoc mode
provides a direct communication between two client devices
without a Wireless LAN Access Point.
2
This device must be used with Access Points that have employed and
activated a radar detection feature required for European Community
operation in the 5GHz bands. This device will operate under the control
of the Access Point in order to avoid operating on a channel occupied by
any radar system in the area. The presence of nearby radar operation may
result in temporary interruption in communications of this device. The
Access Point’s radar
You may consult with the local technical support staff responsible for the
wireless network to ensure the Access Point device(s) are properly
configured for European Community operation.
Safety Precautions
This section is designed to assist you in identifying potentially unsafe
conditions while working with this product. Required safety features have
been installed in the computer to protect you from injury. However, you
should use good judgment to identify potential safety hazards:
1. Please read these safety instructions carefully.
2. Please keep this User's Manual for later reference.
3. Please disconnect this equipment from AC outlet before cleaning.
Don't use liquid or sprayed detergent for cleaning. Use moisture
sheet or cloth for cleaning.
4. For pluggable equipment, that the socket-outlet shall be installed
near the equipment and shall be easily accessible.
5. Please keep this equipment from humidity.
6. Lay this equipment on a reliable surface when installed. A drop or
fall could cause injury.
7. Make sure to use the right voltage for the power source when
connecting the equipment to the power outlet.
8. Place the power cord in such a way that people can not step on it.
Do not place anything on top of the power cord.
9. All cautions and warnings on the equipment should be noted.
10. If the equipment is not use for a long time, disconnect the equipment
from the main power outlet to avoid being damaged by transient
overvoltage.
11. Never pour any liquid into the opening, this could cause fire or
electrical shock.
12. Never open the equipment. For safety reason, the equipment should
only be opened by a qualified service personnel.
13. If on the following situations arises, get the equipment checked by a
service personnel:
3
The Power cord or plug is damaged.
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
The equipment has not worked well or you cannot get it work
according to the user's manual.
The equipment has dropped and damaged.
If the equipment has obvious sign of breakage.
14. Do not leave this equipment in an environment unconditioned,
storage temperature above 60°C (140°f), it may damage the
equipment.
15. The unit can be operated at an ambient temperature of max. 35°C.
16. The sound pressure level at the operators position according to IEC
704-1: 1982 is equal or less than 70 dB(A).
17. Power Cord Requirements
The power cord set used with the AC adaptor must meet the
requirements of the country where you use the AC adaptor, whether
it is 100-120 or 200-240 Vac. The following information explains
the requirements for power cord set selection.
The cord set must be approved for the country in which it
is used.
The appliance coupler must have a configuration for
mating with a CEE22/EN6032/IEC 320 appliance inlet.
A. For U.S. and Canada:
The cord set must be UL Listed and CSA Certified.
The minimum specifications for the flexible cord are No.
18 AWG.
B. For Japan:
All components of the cord set must bear a “PSE” or “ T ”
mark and registration number in accordance with the
Japanese Dentori Law.
The minimum specifications for the flexible cord are .75m
㎡ conductors.
C. For Other Countries:
The cord set fittings must bear the certification mark of
the agency responsible for evaluation in a specific country.
The flexible cord must be of a HAR (harmonized) type
H03VV-F.
The cord set must have a current capacity of a least 2.5
Amperes and voltage rating of 125 or 250 Vac.
4
18. When using your telephone equipment, basic safety precautions
should always be followed to reduce the risk of fire, electric shock
and injury to persons. These precautions includes the following:
Do not use this product near water, for example, near a
bathtub, washbowl, kitchen sink or laundry tub, in a wet
basement or near a swimming pool.
Avoid using a telephone (other than a cordless type)
during an electrical storm. There may be a remote risk of
electric shock from lightning.
Do not use the telephone to report a gas leak in the
vicinity of the leak.
Use only the power cord indicated in this manual.
19. Do not use the AC adapter near open water or other liquids. Never
spill liquid into the AC adapter.
20. Laser Warning: Laser Class I Product Caution - Invisible laser
radiation when open avoid exposure to beam.
21. Danger of explosion if battery is incorrectly replaced. Replace only
with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer's
instructions. Never remove the battery pack while the power is on as
this may result in data loss when the system loses power.
22. The input receptacle is used as the main disconnect device.
23. Always disconnect all telephone lines from the wall outlet before
servicing or disassembling this equipment. To reduce the risk of fire
use only No. 26 AWG or larger telecommunication line cord.
Wichtige Sicherheitshinweise
1. Bitte lesen Sie diese Hinweis sorgfältig durch.
2. Heben Sie dirse Anleitung für den späteren Gebrauch auf.
3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen.
Versenden Sie Keine Flüssig- oder Aerosolreiniger. Am besten
eignet sich ein angefeuchtetes Tuch zur Reinigung.
4. Die Netzanschluβsteckdose soll nahe dem Gerät angebracht und
leicht zugänglich sein.
5. Das Gerät ist vor Feuchtigkeit zu schützen.
6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten.
Ein Kippen oder Fallen könnte Beschädigungen hervorrufen.
7. Beachten Sie beim Anschluß an das Stromnet die Anschlußwerte.
8. Verlegen Sie die Netzanschlußleitung so, daß niemand darüber fallen
kann. Es sollte auch nichts auf der Leitun abgestellt werden.
5
9. Alle Hinweise und Warnungen, die sich am Gerät befinden, sind zu
beachten.
10. Wird das Gerät üeinen längeren Zeitraum nicht benutzt, sollten Sie
es vom Stromnetz trennen. Somit wird im Falle einer Überspannung
eine Beschädigung vermieden.
11. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder
Flüssigkeien in das Gerät gelangen. Dies könne einen Brand bzw.
Elektrischen Schlag auslösen.
12. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der
elektrischen Sicherheit nur von authorisiertem Servicepersonal
geöffnet werden.
13. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu
trennen und von einer qualifizierten Servicestelle zu Überprüfung.:
Netzlabel oder Netzstecker sind beschädigt.
Flüssigkeit ist in das Gerät eingedrungen.
Das Gerät war Feuchtigkeit ausgesetzt.
Wenn das Gerät nicht der Bedienungsanleitung
entsprechend funktioniert oder Sie mit Hilfe dieser
Anleitung keine Verbesserung erzielen.
Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.
Wenn das Gerät deutliche Anzeichen eines Defektes
aufweist.
14. VORSICHT: Explosiongsgetahr bei unsachgemäßen Austausch der
Batterie. Ersatz nur durch denselben oder einem vom Hersteller
empfohlenem ähnlichen Typ. Entsorgung gebrauchter Batterien
nach Angaben des Herstellers.
15. Dieses Schaltnetzteil kann bis zu einer Außentemperatur von
maximal 35ºC.
16. Die Ausgangswerte dürfen nicht die auf dem Label angegebenen
Werte überschreiten.
17. Anforderungen an das Stromkabel
Das Kabel-Set, das an das Netzteil angeschlossen wird, muss den
Anforderungen des Landes, in dem Sie das Netzteil einsetzen,
genügen, je nachdem, ob die Netzspannung 100-120 oder 200-240V
Wechselspannung beträgt.
Das Kabel-Set muss für das Land, in dem es eingesetzt
wird, zugelassen sein.
Der Gerätestecker des Kabels muss in eine CEE22/
EN603/ IEC 320 Buchse passen.
a. Für die USA und Kanada:
Das Kabel-Set muss UL-gelistet und CSA zertifiziert sein.
6
Die Minimalanforderungen für das Kabel entsprechen No.
18 AWG.
b. Für Japan:
Alle Teile des Kabel-Sets müssen entsprechend dem
japanischen Dentori Law mit einem „PSE“ or „T”-Symbol
markiert sein
Die Minimalanforderungen für das Kabel sind .75m ㎡
Leiter.
c. Für andere Länder:
Die Zubehörteile des Kabel-Sets müssen das Prüfsiegel
derjenigen Stelle, die in dem jeweiligen Land für die
Sicherheitsprüfung zuständig ist, tragen.
Das Kabel muss vom HAR (harmonisierten) Typ H03VV-
F sein.
Das Kabel-Set muss eine Stromkapazität von mindestens
2,5 Ampere haben und Spannungen von 125 oder 250 V
Wechselstrom gestatten.
18. Bei der Benutzung Ihres Telefongerätes sollten Sie immer die
grundlegenden Sicherheitsmaßnahmen beachten, um das Risiko von
Feuer, Stromschlägen und Verletzungen zu minimieren. Zu beachten
sind u.a. folgende Punkte:
Benutzen Sie das Gerät nicht in der Nähe von Wasser, wie
zum Beispiel Badewanne, Waschbecken, Spülbecken,
Waschbottich, in feuchten Kellerräumen oder in der Nähe
von Schwimmbecken.
Benutzen Sie kein Telefon (ausgenommen schnurlose
Modelle) während eines Gewitters. Es besteht das geringe
Restrisiko eines Blitzschlages.
Benutzen Sie das Telefon nicht um ein Gasleck zu melden,
falls es sich in der Nähe des Lecks befindet.
Benutzen Sie nur solch ein Stromkabel, wie in dieser
Anleitung beschrieben.
19. Benutzen Sie das Netzteil nicht in unmittelbarer Nähe zu Wasser
oder anderen Flüssigkeiten. Gießen Sie nie Flüssigkeiten über das
Netzteil.
20. Achtung Laser: Laser Produkt der Klasse I. Achtung - Unsichtbarer
Laserstrahl, vermeiden Sie Kontakt mit dem Strahl bei offenem
Gehäuse.
21. Es besteht Explosionsgefahr, wenn der Akku nicht ordnungsgemäß
ersetzt wird. Ersetzen Sie den Akku nur durch einen Akku gleichen
oder äquivalenten Typs, der vom Hersteller empfohlen wird.
7
Entsorgen Sie Akkus entsprechend den Anweisungen des Herstellers.
Entfernen Sie den Akku auf keinen Fall bei eingeschaltetem
Notebook, da hierdurch Daten verloren gehen könnten.
Things you must remember before working on your computer
Let your computer acclimate itself
Your notebook can easily stand temperature extremes but it doesn’t like
rapid changes in temperature, like going from the cold outdoors to a
warm office. Rapid changes in temperature can cause water droplets to
condense inside your case, threatening to damage the electronic parts
inside.
After receiving your notebook when it’s hot or cold outside, try not to
power up the computer immediately, let the computer adjust to the room
temperature gradually at least for three to four hours.
If your system arrives in cold weather, do
not apply power to the computer or monitor until they have been
allowed to come to room temperature.
Heat, Cold, Humidity, and Glare
Find a suitable place for your computer that’s not too hot, too cold, too
dark, or too bright. Glare can make it hard to read the screen.
• Try to avoid the computer components from being destroyed if it is
over heated, so try to allow plenty of room for air to circulate
around the case.
• Do not block the ventilation opening.
• Do not place your computer in direct sunlight.
Suitable place to work
Your computer will run well wherever you’re comfortable but extremes
of temperature and humidity can be challenging to your system’s parts.
There are some things you can tolerate that the computer can’t – things
like static electricity, dust, water, steam and oil.
In case you decide to pull over for roadside computing, try to choose a
clean, comfortable work area for your system.
A lithium-ion battery pack will be available when you are traveling.
If you are running your system for the first time on battery power, remove
the battery from the package, install it into the system and recharge the
battery to fully prepare for service.
8
INTRODUCTION
Welcome to the Notebook PC
Congratulations on your purchase of the Notebook PC. Your Notebook
features the latest advances in portable computing technology. The
Notebook’s modular design provides maximum expandability without
compromising portability. The high-performance CPU and enhanced IDE
hard drive provides you with extra processing power for handling
complex graphics and running large programs.
Unpacking the Notebook
The Notebook comes securely packaged in a sturdy cardboard shipping
carton. Upon receiving your Notebook, open the carton and carefully
remove the contents. If anything is missing or damaged, please contact
your Notebook dealer immediately. The shipping carton should contain
the following items:
• The Notebook computer
• An AC adapter
• An AC power cord
• Software Drivers CD
Do not throw the packaging materials away. You may need them later if
you have to ship the computer for repairs.
Getting to Know Your Computer
Opening the LCD Panel
At the front of the Notebook you will find a retaining latch on the display
panel that locks the display in closed position when the Notebook is not
in use.
1. Locate the display latch on the front of the unit. Slide the latch until
the display panel releases.
2. Raise the LCD screen and the machine will go to incline position.
At any time you can tilt the display toward or away from you to a
comfortable viewing position.
9
To avoid damage to the display panel:
• Try not to slam the display upon closing it.
• Try not to place any object on top when it is closed or open.
• Be sure the system is turned off or in suspend mode before you
close the display panel.
With the LCD screen open, you will see several features important for
operating your Notebook computer. Each of these features is briefly
described below:
10
1. LCD Cover Release Latch
Slide this latch to the right to open the LCD cover.
2. LCD Screen
Your Notebook computer is equipped with a replaceable color
Liquid Crystal Display (LCD) screen that supports up to 1024 x 768
LCD resolution utilizing an AGP BUS. A built-in backlight allows
you to comfortably view the screen even when ambient lighting is
low.
3. Power/Resume Button
Pressing this button will turn on the system or pressing this button
when the computer is in Suspend mode will resume normal
operation. Pressing this button for 4-6 seconds will also turn off the
system.
4. Short-cut Keys
These two short-cut keys are assigned as functions for: Explorer and
mail respectively.
1. Internet Explorer Button - Use this key to open the
Internet Explorer.
2. Outlook Express Button - Use this key to open
Microsoft's Outlook to send/receive your mail.
5. System Status Indicator Panel
The system status indicator panel keeps you informed of the
computer’s operating status. There are also three system status
indicators — Power On, Suspend and Battery Charge LED — on
the right side of the notebook. (Please refer to "The Right Side"
section description)
11
When lit indicates that the AC adapter is connected.
Indicates that the computer is accessing the DVD-ROM
drive.
Indicates that the computer is accessing the hard disk
drive.
Indicates that the keyboard is in Num Lock mode.
Indicates when the keyboard is in Caps Lock mode. In
this mode, the keyboard produces uppercase text when
you press a key. When you press the Caps Lock key
again, the indicator goes off and the keyboard
produces lowercase text.
Indicates when the keyboard is in Scroll Lock mode.
Some applications will move information across the
screen differently when Scroll Lock is on.
6. Keyboard
Your computer has an 88-key enhanced keyboard that provides all
the functions of a standard 101/102 key keyboard.
7. The Built-in Microphone
The built-in microphone is located to the right of the TouchPad.
8. The Volume Buttons
Press the two buttons to increase and decrease the volume control of
your system.
9. TouchPad
The TouchPad is hardware-compatible with a USB mouse and
software-compatible with the Microsoft mouse.
10. TouchPad Buttons
The buttons below the TouchPad correspond to the left and right
buttons on a standard mouse. A USB mouse will work with the
Notebook PC’s TouchPad simultaneously.
12
The Front
1. The CD-ROM Drive
Your Notebook comes with a swappable 5.25" IDE 24X CD-ROM
drive.
The Left Side
1. The LAN Port
This jack provides a standard RJ-45 connection for integration with
an existing network or a high-speed (DSL or cable) connection via a
network cable.
When using a LAN, please use an EMI
Shielding Cable to minimize an inteference when transmitting.
2. The Modem Port
This jack is an internal 56K voice/fax/data modem. You will
connect your computer to your phone line through this port.
Always disconnect all telephone lines from
the wall outlet before servicing or disassembling this equipment.
To reduce the risk of fire use only No. 26 AWG or larger
telecommunication line cord.
13
The Right Side
1. Kensington Lock
Allows you to connect a special computer lock to secure your system.
You can purchase a lock at most computer retailers.
2. DC IN Connector
Plug the AC adapter into this connector.
3. LED Indicator
The Rear
14
1. Battery Charge
This indicator will lit when the battery is in charging status.
2. Suspend
This indicator will lit when the system enter suspend mode.
3. Power On
This indicator will lit when the notebook is powered on.
1. USB Ports
Your computer includes four Universal Serial Bus (USB) 2.0 ports.
USB2.0 is the latest development in Plug and Play technology.
It will eventually replace the need for separate connectors for
external keyboards, serial ports, and parallel (printer) port.
2. Audio Line Out
You can plug an external speaker, headphone or connect the line out
jack to an audio device such as a cassette recorder to record the
notebook's audio output.
3. External Microphone Jack
This mono microphone jack is used to connect an external
microphone.
4. VGA Port
This port allows you to easily connect an external VGA/SVGA
display monitor into your Notebook using the 15-pin female
connector.
The Bottom Panel
15
1. Battery Secure Lock
Push this button to unlock the battery. This button must be in the
unlock position in order to remove the battery.
2. Battery Release Latch
Lift up this latch to release the battery from its bay.
3. Expansion Compartment
This compartment will serve as an expansion to upgrade your RAM
module.
4. Hard Disk Drive
Your computer includes a 2.5-inch IDE hard disk drive (9.5mm in
height). The notebook PC's BIOS automatically detects IDE drive
types.
5. Battery
Your notebook comes equipped with a factory-installed battery pack
module. After the battery runs down, the module can be removed
and replaced with a charged battery.
16
GETTING STARTED
Connecting to a Power Source
Connecting the AC Adapter
A universal AC adapter is provided to supply your computer with power
and also charge the computer’s battery pack. The adapter’s AC input
voltage can range anywhere from 100 to 240 volts, covering the standard
voltages available in almost every country.
The power cord for the AC adapter requires a three-hole grounded AC
outlet. To connect the computer to an external power source:
• Plug the AC adapter’s connector into the DC-IN connector on the
right of the computer.
• Connect the power cord to the AC adapter and then to a wall outlet.
Do not use inferior extension cords as this
may result in damage to your Notebook. The Notebook comes
with its own AC adapter. Do not use a different adapter to power
the computer and other electrical devices.
Whenever possible, keep the AC adapter plugged into the Notebook and
an electrical outlet to recharge the battery.
Never turn off or reset your Notebook while
the hard disk is in use and the HDD status icon is lit; doing so
can result in loss or destruction of your data. Always wait at least
5 seconds after turning off your Notebook before turning it back
on; turning the power on and off in rapid succession can damage
the Notebook’s electrical circuitry.
17
Turning On Your Notebook Computer
Turn on your Notebook by pressing the power button. The Power-On Self
Test (POST) runs automatically.
After the POST is completed, the computer reads the operating system
from the hard disk drive into computer memory (this is commonly
referred to as “booting” a computer). If your OS (Operating System such
as Windows XP…. etc) is installed, it should start automatically.
To turn the Notebook off, save your work and close all open applications,
click on Start, then Shut Down and select Shut down the computer and
click "Yes" or press the power button for 4-6 seconds.
Operating on Battery Power
Your computer comes with a rechargeable battery pack that lets you
operate the computer without an external power source. When the battery
pack is fully charged, you can operate the computer under the following
conditions:
• The battery pack initially has a full charge.
• No peripheral devices are installed.
• The disk/DVD-ROM drives run no more than 10% of the time.
Only use batteries that are approved by an
authorized dealer that is used on for this model only. All batteries
are not the same and therefore should not be treated as such.
Using the wrong battery could cause serious damage to your
computer and yourself through toxic emissions.
Inserting and Removing the Battery Pack
The battery pack should already be inserted in your Notebook computer
when you unpack it. If not inserted, follow these directions:
1. Turn off the notebook.
2. Ensure that the battery lock button is in the unlocked position.
18
3. Insert the battery into the empty compartment. It is designed so that
it only fits one way. It should easily "click" into place.
4. Be sure that the battery release latch on the battery has clicked into
place. This will prevent the battery from sliding out of its
compartment.
5. Push the battery lock button to the locked position to ensure that the
battery is securely inserted into the battery bay.
To remove the battery pack:
1. Turn off the notebook, turn it over and place it on a solid, flat surface.
Push the battery lock button to the unlocked position.
2. Push the release latch into outer direction.
3. Hold the battery at the finger grip and lift it out of the compartment.
Charging the Battery Pack
The installed battery pack charges automatically any time the computer is
connected to the AC adapter and an external power source.
If this is your first time to use the battery, be sure to fully discharge the
battery and recharged until it is fully charged.
19
Page intentionally left blank
20
USING THE NOTEBOOK COMPUTER
Adjusting the LCD Screen Display
The LCD screen display can be adjusted by the following key
combinations.
KEYS FUNCTIONS
[Fn] + [F7] Decreases the brightness level.
[Fn] + [F8] Increases the brightness level.
[Fn] + [F10] Use this key combination to expand your video
screen or reset to its original size.
[Fn] + [F12] This key combination toggles the display between
the LCD display and an external CRT or
simultaneous.
LCD Care
LCD screens are delicate devices that need careful handling. Please pay
attention to the following precautions:
• When you are not using the computer, keep the LCD screen closed
to protect it from dust.
• If you need to clean your LCD screen, use a soft tissue to gently
wipe the LCD surface.
• Do not put your fingers or sharp objects directly on the surface and
never spray cleaner directly onto the display.
• Do not press on, or store any objects on the cover when it is closed.
Doing so may cause the LCD to break.
External CRT Display
You can hook up an external monitor through the 15-pin CRT connector.
Three configurations are available:
• LCD only
• CRT only
• Simultaneous display of the LCD screen and CRT monitor
21
You can switch between these display configurations by pressing the key
combination [Fn] + [F12]. For information on connecting an external
display, please refer to Chapter Four.
A Tour of the Notebook’s Keyboard
The Notebook’s keyboard uses a standard QWERTY layout with the
addition of special function keys and an embedded numeric keypad for
number intensive data entry. Your keyboard supports Windows by
incorporating the two Windows specific keys. With the two Windows
keys you will be able to access and take advantage of many of the
timesaving features of Windows software.
The function keys (F1-F12) on the top row of the keyboard, serve
different purposes and carry out different tasks depending on the
application you are running.
The cursor (arrow) keys (which are all located in the lower right corner of
your keyboard) and the [PgUp], [PgDn], [Home] and [End] keys (which
are located along the right edge of the keyboard) allow you to move the
active cursor of the computer to various locations on the screen or within
the document.
The embedded numeric keypad consists of 15 keys that make number
intensive input more convenient. Like the [Num Lock] key, these keys are
labeled in blue on the keycaps. Numeric assignments are located at the
upper right of each key.
When the numeric keypad is engaged, the NumLock icon will appear in
the System Window. The keypad is activated by pressing the [Fn] +
[NumLk] key. If an external keyboard is connected, pressing the
NumLock key on either the Notebook or external keyboard will
enable/disable NumLock of both keyboards in unison.
To disable the Notebook numeric keypad while keeping the keypad on an
external keyboard activated, use the [Fn] + [NumLk] hot key on the
Notebook keyboard.
The Notebook’s Hot Key Controls
KEYS FUNCTION(S)
Power Button Press this button once to power on or enter the
suspend/resume mode
Press this button for more than 4 seconds can
force to power off the system
Internet Button Open Internet WWW Home short-cut key
Email Button Open Email Reader short-cut key
Volume Up Press this button to increase the system
22
volume
Volume Down Press this button to decrease the system
volume
[Fn] + [F1] Turns on/off the battery beeping sound
[Fn] + [F2] Turns on/off the volume.
[Fn] + [F3] Decreases the system volume
[Fn] + [F4] Increases the system volume
[Fn] + [F5] Enable/Disable the system Touchpad function
[Fn] + [F7] Decreases the brightness level
[Fn] + [F8] Increases the brightness level
[Fn] + [F10] Expand your video screen or reset to its
original size
[Fn] + [F12] Toggles the display between the LCD display
and an external CRT or simultaneous
The TouchPad
The touchpad is a rectangular electronic panel located just below your
keyboard. You can use the static-sensitive panel of the touchpad and slit it
to move the cursor. You can use the buttons below the touchpad as left
and right mouse buttons.
TouchPad Precautions
The TouchPad is a pressure sensitive device. Please take note of the
following precautions.
• Make sure the TouchPad does not come into contact with dirt,
liquids or grease.
• Do not touch the TouchPad if your fingers are dirty.
• Do not rest heavy objects on the TouchPad or the TouchPad buttons.
You can use the TouchPad with Microsoft Windows as well as nonWindows applications.
23
Data Storage and Retrieval
Data storage and retrieval are two of the most fundamental tasks you will
perform when working with your computer. The Notebook is equipped
with a hard disk drive (HDD). The HDD is removable allowing for easy
upgrades.
The CD/DVD-ROM
Features of the CD/DVD-ROM Module
The features of the CD/DVD-ROM/Combo drive are listed below.
• The Audio Play feature allows you to play music CDs
• Front panel load/unload button
• Supports CD-DA, DVD-ROM mode 1 and mode 2, Multi-Session
Photo CD™, CD-I/Video CD (pcs.)
• Low power consumption
• 12.7mm height
Precautions for Handling CD/DVD-ROM/Combo Discs
• Always hold the disc by the edges, avoid touching the surface.
• Use a clean, dry, cloth to remove dust, smudges, or fingerprints.
Wipe from the center outward.
• Do not write or place objects on the surface of the disc.
• Store discs in a cool dry place not to damage the disc.
• Do not use benzene, thinners, or cleaners with detergent. Only use
CD/DVD-ROM cleaning kits.
• Do not bend or drop the discs.
Loading a Disc
To play a CD disc, follow the instructions listed below.
• Push the CD/DVD-ROM/Combo eject button on the CD drive door.
Gently pull the tray all the way out.
• Carefully lift the CD disk by the edges and make sure the shiny
surface is face down (the side with no writing on it). Carefully
insert the CD onto the tray. Push the CD/DVD-ROM down gently
so that it snaps onto the center ring.
• Push the tray back into the drive.
To remove a disk, do the following:
• Check the LED display and make sure that the computer is not
accessing the DVD-ROM drive.
• Push the eject button and pull the tray all the way out.
24
• Carefully pick up the CD disk by the edges and – while pressing
down on the center ring – remove the CD/DVD-ROM/Combo from
the tray.
• Do not insert any foreign objects into the disc tray. If you
experience difficulty when ejecting the CD disk tray, stretch a
paper clip (or use a pin or a thin metal rod) and insert it into the
emergency eject hole located on the right side of the front panel.
The CD disk tray should eject immediately. This procedure can
also be used to remove a CD from the drive when the Notebook is
powered off.
Power Saving Modes
This section contains information on the Notebook’s power system,
including the AC Adapter, the battery system, recharging the battery, and
tips for conserving battery power. The power system is comprised of two
parts, the AC Adapter and the battery system. The AC Adapter converts
AC power from a wall outlet to the DC power required by the computer.
The Battery Power System
A fully charged pack will provide battery life depending on your system
configuration application it runs. Before using the computer on battery
power for the first time, check the battery status icon on the Windows
Toolbar to make sure the battery is fully charged.
See Battery Status later in this section for a description and explanation of
the Windows Battery icon. If possible, always charge the battery
completely.
If you use the battery so frequently that it
exceed more than 20 times by fully discharging/charging in a
single month alone, we recommend you to perform the “Battery
Calibration” process every 3 months to maintain the battery life.
Please refer to the topic on “Battery Calibration” describing how
to calibrate your system battery discussed on the latter part of
this chapter.
If you discover the battery life is getting shorter, please perform
the “Battery Calibration” process immediately.
Removing the Battery Pack
To remove the battery pack from its compartment, please refer to Chapter
3, Inserting and Removing the Battery Pack.
25
Preparing the Battery Pack for Use
Before using the battery pack for the first time, the Smart Battery IC
within the battery pack should be calibrated in order to get accurate
reporting of remaining battery life status. To calibrate the battery pack
follows the instructions below:
• Insert the battery into the battery compartment and turn on the
Notebook. If the battery is completely without power go to the next
step. Otherwise, let the battery run down until the battery low-low
warning beeps are heard. The system will automatically enter
Suspend mode.
• Turn the Notebook off. Connect the AC adapter and let the battery
fully recharge. When the battery charge indicator turns off, the
battery is fully charged.
• Turn On the notebook, let the battery run down until the battery is
in low-low state and you hear a warning beeps. The system will
automatically enter the Suspend mode. You can now connect the
AC adapter.
• The battery pack is now calibrated properly.
In general, using the battery until the low-low battery-warning indicator
appears and fully recharges the battery each time (full discharge/charge
cycle) will ensure the accurate reporting of the battery gauge status.
Automatic Battery Pack Charging Function
You can automatically charge the battery pack by using the AC Adapter.
The following table summarizes the charging modes:
Charge Mode
Fast 4 cell, 2 hours/6 cell, 3 hours/8 cell, 4 hours
with the system off or in Suspend mode. The
temperature must be 25°C or below room
temperature.
Pre-Charge A pre-charge is supplied to the Li-Ion battery
pack.
Charge Time
Battery Status
Windows XP has an applet in the Control Panel that will display an icon
in the Windows taskbar indicating when the Notebook is running on
battery power or is attached to the AC adapter. This applet also displays
a meter that indicates how much charge is remaining in the battery.
26
Battery Low Warning
When the pack initially reaches the “Battery Low” state approximately 10
~ 15 minutes of the usable battery life is left. You will hear audible beep
signals alerting you to the “Battery Low” status. When the battery power
reaches the “Battery Low Low” status the beeping sound will accelerate.
Your battery now has 1~2 minutes of battery charge remaining. You must
save your data or connect AC power immediately; otherwise, you may
lose your data.
Sound Meaning
Continuous
beeping
Beeping
accelerates
Battery Low: Indicates that there is 10 to 15
minutes charge remaining.
Battery Low Low: Indicates that there is 1 to
2 minutes of battery charge remaining. Save
your work and turn off the Notebook, or
connect the AC adapter.
When there is only one minute of battery charge remaining, the Notebook
will suspend to the HDD and power off. You should connect AC power
and resume to save your work.
Small Battery for the Real Time Clock
There is a small built-in battery pack that supplies power to the system in
order to maintain certain system information while the power is off. If the
Notebook is left without a power source for long period of time, this
battery will be exhausted and system information will be lost.
Danger of explosion if battery is incorrectly replaced. Replace only with
the same or equivalent type recommended by the manufacturer. Dispose
of used batteries according to the manufacturer's instructions.Never
remove the battery pack while the power is on as this may result in data
loss when the system loses power.
Battery Calibration
The purpose for this process is to provide a long battery life for your
system battery pack.
1. Turn on the computer, when the text appears, press [Del] or the
[Delete] key until the system enters the BIOS Setup screen, you may
now make the necessary changes.
27
2. Press the arrow key until it reaches the “Exit” menu screen.
Again press the arrow key and select the “Battery Calibration”
item.
Press the [Enter] key and disconnect the AC adapter then press the
[Y] key until you hear continuous battery low-low warning beeping
sounds. The system will be fully discharge and shutdown completely.
3. Connect the AC adapter and let the battery fully recharge. The
“Battery Charge LED” which is located at the right side of the
notebook will light indicating it is in charging status.
4. When the battery charge LED turns off will indicate the system is
fully charged.
5. Repeat step 1 to 4 once again.
6. The battery is now fully calibrated.
Resetting the System
After installing a software application package, you may be prompted to
reset the system to load the changed operating environment. To reset the
system, or “reboot,” press the [Ctrl]+[Alt]+[Delete] keys simultaneously.
This is known as “warm boot.” This key combination acts as “software”
reset switch when you encounter hardware or software problems, which
lock up the Notebook.
If this key combination does not shut down the Notebook, you can reset
the Notebook by using the Notebook’s power button. Should the
Notebook lock up for some reason, pressing this button powers the
Notebook off.
Adjusting the Brightness
To adjust the brightness on the LCD screen, press and hold down the [Fn]
key in the lower left hand corner of the keyboard and press the [F7] key
to reduce the brightness or [F8] to increase the brightness.
28
DESKTOP OPERATION
Your notebook is capable of providing you with efficient and productive
mobile computing; it also has the speed and capacity to service as a
desktop system.
This chapter discusses those functions of your notebook that are typical of
desktop systems.
Audio
The Multimedia Sound System
The Notebook’s built-in audio capabilities allow you to take advantage of
a wide range of education and entertainment multimedia software. The
Notebook is equipped with two internal stereo speakers, a microphone,
and input audio ports for external audio units.
An external microphone can be connected to the microphone jack.
External speakers or headphones can be connected to the Notebook’s
audio-out jack.
All audio features are software controlled. The Notebook’s multimedia
sound system includes the following features:
• Supports Windows Sound System compatibility
• Full Duplex operation
• Dynamic filtering reduces noise and distortion rate
• 16-bit digitized audio playback
• Digitized audio recording through the Notebook’s built-in
microphone or any external source
Audio Volume Control
The Notebook is equipped with hot-key volume controls: Pressing the [Fn]
+ [F3] hot-key combination decreases the audio output volume; press the
[Fn] + [F4] hot-key combination increases the audio output volume.
Audio Software
Your notebook comes equipped with an integrated sound system capable
of providing you with quality audio sound through the built-in speakers or
through external speakers connected via the system ports.
29
Sound Recording
Your system allows you to record sounds and store them as files using the
microphone via the microphone jack on the rear of the notebook
computer. Check the Windows Help and Support Center in Windows for
information on using the various elements in sound recording.
For a high-quality sound, click on the
"Volume Control" at the lower right end of your screen. From the
Volume Control windows, click on the "Advanced" tab, click and
select the "Microphone Boost" item.
Playing Sound Files
Your notebook can play audio files stored in MIDI, WAVE or MP3 file
format. Check the Help and Support Center in Windows for information
on the functions of the Media Player.
External Microphone
The sound system is capable in providing high-quality sound to external
speakers and receiving and processing sounds from an external
microphone or external sound source.
Connecting Peripheral Devices
30
CONFIGURING & MAINTAINING
YOUR SYSTEM
Introduction
The BIOS (Basic Input and Output System) Setup program is a menu
driven utility that enables you to make changes to the system
configuration and tailor your system to reflect installed hardware or alter
system performance. When the Notebook is turned back on, the system is
configured with the values stored in CMOS. With easy-to-use menus, you
can configure such items as:
• Hard drives and peripherals
• Bootup Drive Sequence
• Password protection
The settings made in the BIOS Setup program intimately affect how the
Notebook performs.
Navigating through BIOS Setup
The Setup program has been designed to make it as easy to use as
possible. If you accidentally make a setting and don’t know which one to
switch back to, the Setup program has a hot key that allows you to return
to the previous value.
Accessing the BIOS Setup Program
To access the BIOS Setup program, press the DEL key after the
Notebook has run through its POST.
Item Specific Help
On the right side of the Setup screen is an area labeled Item Specific Help.
This area will list navigation key shortcuts and information that is specific
for the item that you are currently editing.
The Menu Bar
The top of the screen has a menu bar with the following selections:
• Main - Use this menu to make changes to the basic system
configuration.
31
• Advanced - Use this menu to enable and make changes to the
advanced features available on your system, such as enabling the
FIR module.
• Security - Use this menu to set a password. The password allows
bootup and controls access to the BIOS setup menu.
• Boot - Use this menu to configure the default system device used
to locate and load the Operating System and for booting up the
Notebook.
• Exit - Use this menu to exit the current menu or specify how to
exit the Setup program.
To access the menu bar items, press the right or left arrow key on the
keyboard until the desired item is highlighted.
The Legend Bar
At the bottom of the Setup screen you will notice a legend bar. The keys
in the legend bar allow you to navigate through the various setup menus.
The following table lists the keys found in the legend bar with their
corresponding alternates and functions.
Legend Key Alternate
Key
F1 Displays the General Help
window. It can be enabled from
anywhere in the BIOS.
Esc Jumps to the Exit menu or
returns to the Main menu from a
submenu.
←
→
↑ or ↓
Tab Enter Moves the cursor to the next
Minus key (-)
Plus key (+) Scrolls forward through the
Home PgUp Moves the cursor to the field at
End PgDn Moves the cursor to the field at
Selects the menu item to the left.
Selects the menu item to the
right.
Keypad
arrow keys
Scrolls backward through the
Moves the cursor up and down
between fields.
position available in the field.
values for the highlighted field.
values for the highlighted field.
the top of the window.
the bottom of the window.
Function
32
F9 Sets the parameters for the
current menu to their default
values.
F10 Save and Exit.
Enter Will select a sub menu or show a
range of options for a field.
Launching Submenus
Note that a right pointer symbol appears to the left of certain fields.
This pointer indicates that a submenu can be launched from this field. A
submenu contains additional options for a field parameter.
To call up a submenu, simply move the cursor to highlight the field and
press the [Enter] key. Use the [Esc] key to return to the Main menu.
General Help
In addition to the Item Specific Help window, the BIOS Setup program
also provides a General Help screen can be called up from any menu by
simply pressing [F1].
Use the [PgUp] and [PgDn] keys or the up and down arrow keys (↑↑↑↑↓↓↓↓) to
scroll through the entire help document. Press the Home key to display
the first page, press End to go to the last page. To exit the help window,
press the [Enter] or the [Esc] key.
Save Changes and Exit the Setup Program
Refer to the Exit menu section of this chapter for detailed information on
saving changes and exiting the setup program.
33
The Main Menu
When the Setup program is accessed, the following screen appears:
34
The Advanced Menu
Selecting Advanced from the menu bar displays the Advanced menu:
35
The Boot Menu
The Boot menu allows the user to specify the order in which the
Notebook is to check for a device to boot the system. You can also
configure the way that the system will boot up.
To make changes, select Boot from the menu bar. The following screen
appears:
36
The Security Menu
The Notebook’s advanced system of security allows you to set a
password to prevent unauthorized access to system resources, data, and
the BIOS Setup Program.
37
The Exit Menu
Once you have made all of your selections from the various menus in the
Setup program, you should save your changes and exit Setup. Select Exit
from the menu bar to display the following menu:
38
VGA UTILITIES
VGA Utilities
After you have restarted Windows, open the “Control Panel” and double
click on the “Display” icon. From the “Display Properties” window,
select the “Settings” tab and click on the “Advanced” tab to enter the
“Digital Flat Panel (1024x768) on VIA/S3G UniChrome Pro IGP"
window. You will notice four new entries have been made in the "Utility
Manager" window: Gamma Correction, Video Setting, Driver Mode
Setting and Product File Information.
39
S3Display
40
S3Gamma Plus
41
S3Info Overlay
42
TROUBLESHOOTING
This chapter describes locating and solving problems that you may
encounter while using your computer.
Locating a Problem
Problems with your computer can be caused by something as minor as an
unplugged power cord – or as major as a damaged hard disk. The
information in this chapter is designed to help you find and solve minor
problems. If you try all the suggested solutions and you still have a
problem, make a list of what steps you have taken to correct the problem
and contact your dealer.
Successful troubleshooting is the result of careful observation, deductive
reasoning, and an organized approach to solving the problem. The
problems that you will encounter can be divided into two basic categories:
hardware problems and software problems. Hardware problems can be
further divided into electrical and mechanical problems. You will know
you have a hardware problem if the screen is dark, the computer cannot
read the disk drives, or you get an error message during the Power-On
Self Test (POST).
Software errors can occur at several levels. The ROM BIOS and the
operating system can give you a large number of error messages. On top
of this, each application software package has its own set of error
messages. It is important to determine whether the software error message
you are getting is from the application or the operating system. Once you
know this, you can look in the respective manual for a solution to the
problem.
Checking Cables and Connections
Start by performing a careful visual inspection of the exterior of the
computer. If no LEDs are illuminated, make sure that your computer and
its peripherals are getting power and communicating with each other
properly.
To check the power cables, and connections:
1. If you have been using battery power, connect the Notebook to an
external power source and make sure that the battery has a charge.
43
2. If you are using the Notebook with the AC adapter, check the power
outlet, the power cord, and any power switches that may affect your
computer.
Check the wall outlet or power strip with an item that you
know is functioning properly. A lamp or radio is a convenient
item for checking the power. You may also need to check the
fuses and breakers in your electric box.
If the outlet is controlled by a wall switch, make sure that the
switch is on.
If the outlet is controlled by a dimmer switch, use a different
outlet.
If your computer is plugged into a power strip with an On/Off
switch, make sure the switch is on.
With the computer’s power switched off, check all cable connections. If
the computer is connected to any peripheral devices, look for loose or
disconnected cables.
• If the computer is too close to a wall, a cable connection may be
loose or the cables may be crimped.
• Do not substitute cables for different devices (other than the
manufacturer recommended cables) even if they look exactly alike.
The wiring inside the cable may be different.
When you are certain that you have power available and all connections
are good, turn the computer on again. If the computer still does not start,
you may have a hardware problem.
The Power-On Self Test
The Power-On Self Test (POST) runs every time you turn on or reset the
Notebook. The POST checks memory, the main system board, the display,
the keyboard, the disk drives, and other installed options.
A few seconds after you turn on your computer, a copyright message
appears on your display screen. A memory test message appears next; as
the test continues, memory size increases until all installed memory is
tested. Normally, the only test routine visible on the screen will be the
memory test.
Two classifications of malfunctions can be detected during the POST:
• Error messages that indicate a failure with either the hardware, the
software, or the Basic Input/Output System (BIOS). These critical
malfunctions prevent the computer from operating at all or could
cause incorrect and apparent results. An example of a critical error
is microprocessor malfunction.
44
• Messages that furnish important information on the power-on and
boot processes (such as memory status). These non-critical
malfunctions are those that cause incorrect results that may not be
readily apparent. An example of a non-critical error would be a
memory chip failure.
In general, if the POST detects a system board failure (a critical error),
the computer halts and generates a series of beeps. If failure is detected in
an area other than the system board (such as the display, keyboard, or an
adapter card) an error message is displayed on the screen and testing is
stopped. It is important to remember that the POST does not test all areas
of the computer, only those that allow it to be operational enough to run
diagnostic programs.
If your system does not successfully complete the POST, but displays a
blank screen, emits a series of beeps, or displays an error code, consult
your dealer.
General Hardware Problems
A few common hardware problems and suggested solutions are presented
in the table below:
Problem: The capacity of the battery is between 95 to 99% but
can not fully charged.
Solution: Please discharged to less than 95% of its capacity
then recharge the battery.
Problem: Failure in the installation of the Audio driver.
Solution: Be sure to first remove the current audio device from
your system. Please follow the instruction on the installation of
audio driver.
Problem: The display screen is dark
Solution: Make sure that the computer is not in Suspend mode.
Check the Brightness controls for the screen. If the controls are
turned too far down, the screen will be dark.
Problem: An incorrect date and time are displayed.
Solution: Correct the date and time using the DOS DATE and
TIME commands or the options in the Setup Utility. If the date and
time become incorrect after a short time, your CMOS battery may
be depleted. Contact your dealer to change the battery.
Problem: You hear irregular beeps during operation of the
Notebook and the system halts.
Solution: The problem is beyond the scope of this manual.
Contact technical support.
45
Problem: An unidentified message is displayed.
Solution: Reboot the computer and run the BIOS system setup.
Confirm the Setup parameters. If the same message is displayed
after booting up again, contact technical support for assistance.
Problem: The system cannot access the DVD-ROM drive.
Solution: Check that a CD is properly inserted in the drive.
Make sure that you are using the correct program for that kind of
CD. For example, the system cannot read a data CD using an
audio program.
Problem: You cannot operate the printer.
Solution: Check the printer cable connection. Ensure that the
printer power switch is turned on. Confirm that the printer is on-line.
Problem: You cannot use the mouse.
Solution:
• Check the cable connection.
• Check the mouse with another application to see if there is a
software incompatibility problem.
• If possible, check the mouse with another computer to see if it
works. If it doesn’t operate on a different system, the mouse might
be broken.
Contacting Your Dealer
If you still have a problem after reading the preceding sections, the next
step is to contact your dealer. Your dealer can determine if the problem is
something that requires the computer to be taken to the shop. Before you
call your dealer, however, prepare the following information:
• How is your computer configured? Your dealer needs to know what
peripheral devices you are using.
• What messages, if any, are on the screen?
• What software were you running at the time?
• What have you done already to try to solve the problem? If you
have overlooked a step, your dealer may be able to solve the
problem over the phone.
46
HOW DO I EXPAND MY NOTEBOOK
Upgrading your Memory
Refer to the following instructions and illustration for information on
upgrading your notebook's memory.
1. Turn off the computer and disconnect the AC adapter and all
peripherals.
2. Turn the notebook over so that the rear ports are facing you and
locate the memory module compartment.
3. Remove the screws that secure the RAM module compartment cover
and set it aside in a safe place.
4. Remove the compartment cover and then angling it up and out.
5. If you need to install a higher capacity module, gently push the edge
clips on both sides to release the module. Angle the card slightly
upward and gently slide it from its edge connector slot. Store the
card in the anti-static bag that contains your new module(s).
47
6. To install the new memory card, hold the card with its gold edge
connector toward the edge connector slot of the compartment. To
help you orient the cards, the edge connector has been made with
two unequal-length sections. You will only be able to insert the card
in one direction.
7. Insert the edge connector into the slot. The gold edge connector of
the card should not be visible when the card is fully inserted.
8. Press the card downward where you should hear an audible click as
the latches of the connector secure the card in place.
9. Once the module is properly seated, you can replace the cover on
this compartment.
10. Replace and tighten the screw.
Easy to Upgrade HDD Module
The hard drive in your notebook computer is made to be easily swapped
out for upgrading. You should back up your hard drive before attempting
o change the hard drive.
Make sure that before you install a new drive, all the files in your system
should be backed up.
How to upgrade your Hard Drive
48
SPECIFICATION
Detailed Notebook Specifications
Processor
• VIA C7 Processor, FSB 533/400 MHz, L2 cache 128KB on die
Operating System Compliance
• Microsoft® Windows® XP Professional Edition
• Microsoft® Windows® XP Home Edition
Core Logic
• VIA VN800 + VIA VT8237R+
Memory
• Expansion 1 slot of 200pin SO-DIMM DDRII module, expandable
up to 1GB system memory
• Support DDRII 533 / 400 DDR module
LCD Display
• 14.1” XGA (1024 x 768) TFT LCD display
Video & Graphics
• Embedded in North bridge (VIA VN800), SMA up to 128MB
DDRII SDRAM
Hard Drive
• 2.5” 9.5mm height, PATA / SATA alternative support (Factory
Option)
Optical Drive
• 5.25" 12.7mm DVD-ROM, Combo (DVD-ROM+ CD-RW), DVD-
Dual (DVD+/-RW), Super Multi (DVD-RAM+DVD+/-RW)
Pointing Device
• Synaptics touchpad
49
Application Launch Key
• E-mail, Internet, Volume Up, Volume Down hot key
LED Status Indicator
• Battery, suspend, power on, AC adapter, DVD-ROM drive, hard
disk drive, Num Lock mode, Caps Lock mode, Scroll Lock mode
Keyboard
• 3.0mm travel, inverted-T, 88keys with Windows keys
AC Adapter
• Input: 100-240V AC, 50-60Hz, 1.5A, Universal
• Output: 19V DC, 3.42A, 65W
Battery
• 4 cell / 6 cell / 8 cell Li-Ion battery pack
BIOS
• AMI, Support PnP, password
Communication
• 10/100 Base-T LAN on board
• Built-in MDC 56Kbps V.90 FAX/Modem
Power Management
• ACPI 2.0 compliance
• Support Stand-by, Suspend to Disk, Suspend to RAM
Security
• Kensington Lock, BIOS password protection
Size
• 315mm(W) x 255mm (D) x 35mm (H)
Weight
• 2.7 kg with 14.1” panel, 4 cell battery and Optical drive installed
Accessories
Packing Accessories
• Quick Guide, Support CD (Driver, Utility, Manual), AC Adapter,
Power Cord, Battery Pack
50
Factory Option
• Optical Device: DVD-ROM, Combo (DVD-ROM+ CD-RW),
DVD-Dual (DVD+/-RW), Super Multi (DVD-RAM+DVD+/-RW)
• Support IEEE 802.11 b or IEEEE 802.11g
• Spare Li-Ion Battery Pack
PS
• Battery life will vary depending on your specific hardware and
software configuration
• Spec subject to be changed without notice
51
Loading...