Elite EPB-1800 User Manual
17PC Personal Drink Blender
Model EPB-1800
Instruction Manual
Before operating your new appliance, please read all instructions carefully
and keep for future reference
Always follow basic safety precautions when using electrical products, especially
when children are present.
WARNING: To avoid the risk of electrical shock, always make sure the product is
unplugged from the electrical outlet before assembling, disassembling,
relocating, servicing, or cleaning it.
WARNING--To reduce the risk of fire, electrical shock, or serious personal
injury:
READ ALL INSTRUCTIONS BEFORE USING
This product is intended for use in processing foods for human
consumption. Do not use the product for any other purpose.
Do not leave the product unattended while in use. Always unplug the
product from the electrical outlet when not in use.
Keep the Power Cord and product away from heated surfaces.
Do not submerge product base in or expose it to water or any other liquids.
Do not use this appliance outdoors.
Do not use attachments not recommended or sold by the product
manufacturer.
Use extreme caution when handling the Blade assembly as the blades are
extremely sharp. Use caution when attaching or detaching the Blade
assembly.
Do not touch moving parts (e.g., the Blades) while the product is in use.
Keep hands and utensils away from the moving blade assembly while
operating the product.
Before disassembling the product, unplug it from the electrical outlet and
ensure the Blades have completely stopped.
Do not plug or unplug the product into/from the electrical outlet with a
wet hand.
To disconnect from an electrical outlet, pull directly on the plug; do not pull
on the Power Cord.
Unplug the product from the electrical outlet prior to putting on or
removing parts.
Never operate this product if it has a damaged Power Cord or plug, is not
working properly, has been dropped or damaged, or if the Base has been
exposed to water or other liquids. Do not attempt to examine or repair this
product yourself. Only qualified service personnel should perform servicing.
Take the product to an appliance repair shop of your choice for inspection
and repair.
1
CAUTION-- To reduce the risk of personal injury or product damage:
Do not allow the Power Cord to hang (e.g., over the edge of a table or
counter) where it may be tripped over or pulled.
Always place the product on a flat, level, stable surface.
Keep the product out of the reach of children and pets. This product is not
intended for use by children.
This product is intended for indoor, non-commercial, non-industrial,
household use only.
SPECIAL INSTRUCTIONS:
a) To avoid a circuit overload when using this product, do not operate another
high-wattage product on the same electrical circuit.
b) If an extension cord is used with this product, a 10-amp extension cord should
be used. Extension cords rated for less amperage may overheat. The marked
electrical rating of the cord set or extension cord should be at least as great as
the electrical rating of the product.
NOTE: A short power cord is provided to reduce the risk of personal injury
resulting from becoming entangled in or tripping over a longer cord.
Longer power-supply cords or extension cords are available and may be used if
care is exercised in their use.
If an extension cord is used: (1) the marked electrical rating of the extension
cord should be at least as great as the electrical rating of the product; (2) the
extension cord should be arranged so that it will not drape over the countertop
or tabletop where it can unintentionally be pulled on or tripped over by children
or pets.
This appliance is equipped with a
other), please follow the below instructions:
To reduce the risk of electrical shock, this plug is intended to fit into a polarized
outlet only one way. If you are unable to fit the plug into the electrical outlet,
try reversing the plug. If the plug still does not fit, contact a qualified
electrician. Never use the plug with an extension cord unless the plug can be
fully inserted into the extension cord. Do not alter the plug of the product or
any extension cord being used with this product. Do not attempt to defeat
the safety purpose of the polarized plug.
polarized plug
(one blade is wider than the
2
A. Power Switch
B. Base (1)
C. Power Cord
D. Cross Blade Assembly (1)
E. Drinking Cap
F. Removable Spill-proof Lids (4)
G. Foam Grips (4)
H. Grinder Cup (1)
I. Mixing Cup (4)
J. Flat Blade Assembly (1)
NOTE: Before using the product for the first time, disassemble and thoroughly
wash and dry all accessories (EXCEPT the main Base) such as the cups, blade
assembly and spill-proof lids).
WARNING: Ensure the product is unplugged from the electrical outlet before
assembling it. Handle the Blade assembly with care as the blades are extremely
sharp. Use caution when attaching, detaching, cleaning, or storing the Blade
assembly.
3
CHOPPING & BLENDING
1. Ensure the product is unplugged from the electrical outlet.
2. Place the Base on a flat, level, stable surface.
3. Fill the Small Cup or the Large Cup with the food that you wish to
chop/blend.
4. Screw the Flat Blade assembly or Cross Blade assembly clockwise onto the
Small or Large Cup until secure.
NOTE: Ensure that the rubber gasket, located on the inside bottom edge of
the blade assembly, is in place. This will prevent leaking.
5. Turn the Chopper Cup Assembly upside down so that the Blade assembly is
on the bottom. Attach the assembled Chopper by aligning the three tabs on
the outside of the Small or Large Cup with the three notches on the top
inner edge of the Base.
6. Plug the product into a standard 120-volt AC electrical outlet.
7. Each Cup Assembly has three small tabs which fit into three grooves on the
top lip of the Base. Press down on the Cup Assembly firmly and turn it
counter-clockwise to lock into place. Press and hold the Power Pulse switch
to operate. To prevent product overheating, limit continuous operation to
five seconds at a time. NOTE: The Cup Assembly MUST be locked in order
to operate.
8. To stop processing, simply let go of the Power switch. Wait until the Blades
stop completely before removing the Cup Assembly by turning it clock-wise
to unlock it from the Base.
9. Unplug the product from the electrical outlet when it is not in use or is left
unattended.
USING DRINKING CUPS:
1. Ensure the product is unplugged from the electrical outlet.
2. Place the Base on a flat, level, stable surface.
3. Add the ingredients that you wish to include in your drink into one of the
Drinking Cups.
blade assembly.
4. Screw the Cross Blade assembly onto the Drinking cup.
5. Turn the Drinking cup so that the Blade assembly is on the bottom. Attach
the assembled Drinking cup by aligning the 3 tabs on the sides of the
Drinking cup with the 3 notches on the top inner edge of the Base.
6. Plug the product into a standard 120-volt AC electrical outlet.
7. Each Cup Assembly has 3 small tabs that fit into 3 grooves on the top lip of
the Base. Press down on the Cup Assembly firmly and turn it counterclockwise to lock into place. Press and hold the Power switch to operate.
To prevent product overheating, limit continuous operation to
five seconds at a time. NOTE: The Cup Assembly must be locked in order to
operate.
8. To stop processing, simply let go of the Power switch. Wait until the Blades
stop completely before removing the Cup Assembly by turning it clock-wise
to unlock it from the Base. assembled Drinking cup and Blade assembly from
the Base. Turn the Drinking cup so that the Blade assembly is on top.
Unscrew the Blade assembly from the Drinking cup; screw one of the spillproof lids onto the threads on the top of the Drinking cup.
9. Unplug the product from the electrical outlet when it is not in use.
If attached, remove the spill-proof lids before installing
4
CAUTION: The product is not intended for blending hot liquids. This product is
not intended for blending frozen solid ingredients. It is recommended to chop
ingredients into smaller portions before freezing, and then allow the ingredients
to defrost slightly before mixing. Large frozen solid ingredients may damage the
cups. Crushed Ice is recommended instead of solid ice cubes. For liquid
ingredients, do not fill the containers to their maximum capacity. Overfilling the
Cups could result in spillage, causing burns and/or property/product damage. A
maximum of ¾ of the capacity is recommended.
CHOPPING & BLENDING IDEAS:
The personal drink blender is not exclusively meant for blending of drinks. There
are a number of uses for this appliance.
Use the Flat Blade for chopping dry ingredients.
Use the Cross Blade assembly to blend wet ingredients.
- Chop Nuts - Chop Vegetables
- Grate Cheese - Make Bread crumbs
- Blend Sauces - Blend Dips
- Blend Fresh Baby Food - Scramble Eggs for Omelets
- Blend Salad Dressing - And much, much more…
WARNING: To avoid the risk of electrical shock, always ensure the product is
unplugged from the electrical outlet before assembling, disassembling,
relocating, servicing, or cleaning it.
WARNING: Handle the blade assembly with care as the blades are extremely
sharp. Use caution when attaching, detaching, cleaning, or storing blade a
assembly.
Always clean the product immediately after each use.
Wash all parts except the Base in warm, soapy water; rinse, and dry
thoroughly. DO NOT wash parts inside a dishwasher.
Clean the Base by wiping it with a damp cloth. To avoid damage to the
product, do not immerse the Base into water or any other liquids or place it
in a dishwasher.
To avoid damage to the product, do not use abrasive cleaners or scouring
pads to clean the product parts.
Make sure product is thoroughly dry before storing in a cool, dry place.
5
Loading...