Elica EST630SS Install manual

Use, Care, and

Installation Guide

Guide

d’utilisation,

d’entretien et

d’installation

Guía de

instalación, uso y

mantenimiento

Models: EST630SS

EST636SS

READ AND SAVE THESE

INSTRUCTIONS

LISEZ CES

INSTRUCTIONS ET

CONSERVEZ-LES

LEA Y CONSERVE

ESTAS INSTRUCCIONES

LIB0132564

Printed in Mexico

ENGLISH

Contents

Important safety notice................................................................................................................................................................................................. 3

Electrical & installation requirements ................................................................................................................................................................ 4

Before installing the hood ...................................................................................................................................................................................... 4

Dimensions and clearances......................................................................................................................................................................................... 4

List of materials................................................................................................................................................................................................................. 5

Parts supplied .............................................................................................................................................................................................................. 5

Parts not supplied ...................................................................................................................................................................................................... 5

Ducting options and examples.................................................................................................................................................................................. 6

Installation ......................................................................................................................................................................................................................... 6

Electrical connection................................................................................................................................................................................................ 8

Complete the installation........................................................................................................................................................................................ 9

Description of the hood................................................................................................................................................................................................. 9

Control.................................................................................................................................................................................................................................. 9

Maintenance ...................................................................................................................................................................................................................... 10

Warranty ........................................................................................................................................................................................................................... 11

APPROVED FOR RESIDENTIAL APPLIANCES FOR RESIDENTIAL USE ONLY READ AND SAVE THESE INSTRUCTIONS

PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING. INSTALLATION MUST COMPLY WITH ALL LOCAL CODES.

IMPORTANT: Save these Instructions for the Local Electrical Inspector’s use. INSTALLER: Please leave these Instructions with this unit for the owner. OWNER: Please retain these instructions for future reference.

Safety Warning: Turn o power circuit at service panel and lock out panel, before wiring this appliance. Requirement: 120 V AC, 60 Hz. 15 or 20 A Branch Circuit.

IMPORTANT SAFETY NOTICE

I CAUTION

FOR GENERAL VENTILATING USE ONLY. DO NOT USE TO EXHAUST HAZARDOUS OR EXPLOSIVE MATERIALS OR VAPOURS.

I WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: A. Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the manufacturer.

B. Before servicing or cleaning the unit, switch power o at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

C. Installation work and electrical wiring must be done by qualiﬁed person(s) in accordance with all applicable codes & standards, including ﬁre-rated construction.

D. Sucient air is needed for proper combustion and exhausting of gases through the ﬂue (Chimney) of fuel burning equipment to prevent back- drafting. Follow the heating equipment manufacturers guideline and safety standards such as those published by the national ﬁre protection association (NFPA), the american society for heating, refrigeration and air conditioning engineers (ASHRAE), and the local code authorities.

E. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

F. Ducted systems must always be vented to the outdoors.

I CAUTION

To reduce risk of ﬁre and to properly exhaust air, be sure to duct air outside - do not vent exhaust air into spaces within walls, ceilings, attics, crawl spaces, or garages.

I WARNING

TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCT WORK.

Install this hood in accordance with all requirements speciﬁed.

I WARNING

To reduce the risk of ﬁre or electric shock, do not use this hood with any external solid state speed control device.

I WARNING

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE. a) Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings.

b) Always turn hood ON when cooking at high heat or when ﬂambeing food (I.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambe’).

c) Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or ﬁlter.

d) Use proper pan size. Always use cookware appropriate for the size of the surface element.

I WARNING

TO REDUCE THE RISK OF INJURY TO PERSONS, IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING: a) SMOTHER FLAMES with a close-ﬁtting lid, cookie sheet, or other metal tray, then turn o the gas burner or the electric element. BE CAREFUL TO PREVENT BURNS. If the ﬂames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.

b) NEVER PICK UP A FLAMING PAN - you may be burned. c) DO NOT USE WATER, including wet dishcloths or towels -

a violent steam explosion will result. d) Use an extinguisher ONLY if:

1) You know you have a class ABC extinguisher, and you already know how to operate it.

2) The ﬁre is small and contained in the area where it started.

3) The ﬁre department is being called.

4) You can ﬁght the ﬁre with your back to an exit.

e) Ducted fans must always be vented to the outdoor.

Based on “Kitchen Fire Safety Tips” published by NFPA.

OPERATION

Always leave safety grills and ﬁlters in place. Without these components, operating blowers could catch onto hair, ﬁngers and loose clothing.

The manufacturer declines all responsibility in the event of failure to observe the instructions given here for installation, maintenance and suitable use of the product. The manufacturer further declines all responsibility for injury due to negligence and the warranty of the unit automatically expires due to improper maintenance.

I CAUTION

Automatically Operated Device - To reduce the risk of Injury disconnect from power supply before servicing.

ELECTRICAL & INSTALLATION REQUIREMENTS

IMPORTANT

Observe all governing codes and ordinances.

It is the customer’s responsibility:

• To contact a qualiﬁed electrical installer.

• To assure that the electrical installation is adequate and in

conformance with National Electrical Code, ANSI/NFPA 70 — latest edition*, or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No.0-M91-latest edition** and all local codes and ordinances.

• If codes permit and a separate ground wire is used, it is recommended that a qualiﬁed electrician determine that the ground path is adequate.

• Do not ground to a gas pipe.

• Check with a qualiﬁed electrician if you are not sure range

hood is properly grounded.

• Do not have a fuse in the neutral or ground circuit.

IMPORTANT

• Save Installation Instructions for electrical inspector’s use.

• The range hood must be connected with copper wire only.

• The range hood should be connected directly to the fused

disconnect (Or circuit breaker) box through metal electrical conduit.

• Wire sizes must conform to the requirements of the National Electrical Code ANSI/NFPA 70 — latest edition*, or CSA Standards C22.1-94, Canadian Electrical Code Part 1 and C22.2 No. 0-M91 - latest edition** and all local codes and ordinances.

• A U.L.- or C.S.A.-listed conduit connector must be provided at each end of the power supply conduit (at the range hood and at the junction box).

Copies of the standards listed may be obtained from: * National Fire Protection Association Batterymarch Park Quincy, Massachusetts 02269 ** CSA International 8501 East Pleasant Valley Road Cleveland, Ohio 44131-5575

BEFORE INSTALLING THE HOOD

1 For the most ecient air ﬂow exhaust, use a straight run

or as few elbows as possible. CAUTION: Vent unit to outside of building, only.

2 At least two people are necessary for installation. 3 Fittings material is provided to secure the hood to most

types of walls/ceilings, consult a Qualiﬁed Installer, check if they perfectly ﬁt with your cabinet/wall.

4 Do not use ﬂex ducting. 5 COLD WEATHER installations should have an additional

backdraft damper installed to minimize backward cold air ﬂow and a nonmetallic thermal break to minimize conduction of outside temperatures as part of the ductwork. The damper should be on the cold air side of the thermal break. The break should be as close as possible to where the ducting enters the heated portion of the house. 6 Make up air: Local building codes may require the use of Make-Up Air Systems when using Ducted Ventilation Systems greater than speciﬁed CFM of air movement. The speciﬁed CFM varies from locale to locale. Consult your HVAC professional for speciﬁc requirements in your area.

DIMENSIONS AND CLEARANCES

Models

EST630SS EST636SS

A 30” (76 cm) 36” (91.2 cm)

B 19

C* Max: 52

⁄10” (50.5 cm)

⁄5” (137.6 cm)

Min: 333⁄10” (84.7 cm)

D** Max: 50

⁄10” (127.8 cm)

Min: 297⁄10” (75.4 cm)

E 6” (15.24 cm)

⁄2” (26.8 cm)

⁄16” (33.1 cm)

⁄10” (60.8 cm)

⁄10” (12.6 cm)

F 10

G 13

H 23

I 4

*For non-vented (recirculating installations) **For vented installations

+ 8 hidden pages