Electro-Voice TX1152FM User Manual
Key Features:
T F11X M
55° Vertical Floor Monitor with •
Signal Synchronized Transducers
100 dB Sensitivity, 133 dB Maximum SPL•
DH3 1.25” (32mm) Diaphragm, 1” (25mm) Exit •
Pure Titanium Compression Driver
SMX2151 15” (381mm) LF Transducer with •
Fully Symmetric Drive
Integrated Crossover with Steep 24 dB/ •
Octave Slopes and HF Protection
90° x 50° Coverage Pattern•
500W Continuous (2000W Peak) Power •
Handling
TX1152FM
Single 15” Two-Way,
90° x 50° Full-Range
Vertical Floor Monitor
TM
General Description: Technical Specifications:
The Electro-Voice® TX1152FM is a compact, high output dedicated floor
monitor for use on small to medium-sized stages where high quality vocal and instrument applications are required in a lightweight package.
The TX1152FM enclosure utilizes Signal Synchronized Transducers™
(patent pending), a design that aligns the woofer and compression driver
by locating them on separate baffles, and integrates a low distortion port
between the baffles. This offers tremendous advantages over traditional
flat baffle construction: the acoustic centers of the woofer and compression driver are closer together, synchronizing arrival time; the voice coils
of the compression driver and woofer are in the same plane, achieving
linear phase response; and the size of both baffles are smaller than a
single baffle; resulting in a smaller footprint.
The TX1152FM utilizes the DH3, a high output 1.25” titanium compression
driver, coupled to a Constant Directivity™ 90° x 50° horn. The SMX2151
15” woofer has an FEA optimized magnet structure and shorting ring for
ultra low distortion. The crossover uses steep 24 dB/octave slopes with
equalization for very smooth response in vocal range, and has a built in
protection circuit for long term reliability. The combination of the transducers, enclosure, and crossover result in a compact floor monitor that is
capable of very high output levels levels before feedback.
The TX1152FM has a variety of features that make it suited as a dedicated floor monitor. The internally braced, enclosure is constructed out
of a combination of plywood and MDF, and coated with EVCoatTM for
maximum strength and durability. The unique grille design is very strong
and dent resistant, and features a rotatable logo. Four way handles allow
for gripping the TX1152FM in a variety of positions. The recessed input
panel with dual NL4 connectors is located on the rear of the enclosure,
which keeps the connectors hidden and away from the performers on
stage.
Freq. Response1 (-3 dB): 65 Hz - 20 kHz
Freq. Range1 (-10 dB): 45 Hz - 20 kHz
Rec. Hipass Frequency: 45 Hz
Axial Sensitivity: 100 dB (1W/1m)
Max. Calculated SPL: 133 dB
Horizontal Coverage: 90°
Vertical Coverage: 50°
Power Handling: 500W Continuous, 2000W Peak
LF Transducer: SMX2151, 15 in (381mm) Driver
HF Transducer: DH3, 1.25 in (32mm) Diaphragm
Crossover Frequency: 1750 Hz
Nominal Impedance: 8 Ohms
Minimum Impedance: 6.2 Ohms
Connectors: (2) Neutrik Speakon NL4’s
Enclosure Material: Plywood and MDF with EVCoat
Dimensions (H x W x D): 18.7” x 17.3” x 25.8”
Net Weight: 51.9 lbs (23.5 kg)
Shipping Weight: 59.4 lbs (27.0 kg)
1
Half Space Measurement.
Compression Driver
Grille: 16 GA Steel, Black Powdercoat, with
Rotatable Logo
(475mm x 439mm x 655mm)
TM
Dimension Drawings:
20000
10000
1000
1005020
316
100
10
3.16
70
80
90
100
110
Frequency (Hz)
Sensitivity (dB)
Impedance (Ohms)
Frequency Response, Half Space
Impedance
Top View
Frequency Response & Impedance:
Front View Right View
Block Diagram:
Rear View
TX1152FM Part Numbers
PRD000145-001 TX1152FM, Single 15” Two Way, 90° x 50° •
Vertical Stage Monitor, Black Finish
Performance Match
PRD000162-000 PL80A, Vocal Microphone, Dynamic, •
Supercardioid, Ultra-Low Noise
PRD000144-001 TX1122FM, Single 12” Two Way, 90° x 50° •
Vertical Stage Monitor, Black Finish
D170401 CP4000S, 120V Power Amplifier, 2 x 1400W•
D170312 CP3000S, 120V Power Amplifier, 2 x 1100W•
D170258 CP2200, 120V Power Amplifier, 2 x 800W•
PRD000043-001 DC-One, 120V Digital Loudspeaker Controller•
Electro-Voice
12000 Portland Avenue South, Burnsville, MN 55337
Phone: 952/884-4051, Fax: 952/884-0043
www.electrovoice.com
© Bosch Communications Systems 05/2008
Part Number LIT000182 Rev 2
®
U.S.A. and Canada only. For customer orders, contact Customer Service at:
800/392-3497 Fax: 800/955-6831
Europe, Africa, and Middle East only. For customer orders, contact Customer Service at:
+ 49 9421-706 0 Fax: + 49 9421-706 265
Other Internatonal locations. For customer orders, Contact Customer Service at:
+ 1 952 884-4051 Fax: + 1 952 887-9212
For warranty repair or service information, contact the Service Repair department at:
800/685-2606
For technical assistance, contact Technical Support at: 866/78AUDIO
Specifications subject to change without notice.
Loading...