Electro-Voice RE3-ACC-PASP Datasheet
23.6 mm
PASP
R1
R2
ANT
Passive Antenna Splitter
10 ~ 1000MHz
DC 12V
Booster Power
72.2 mm
54.9 mm
Electro-Voice | RE3-ACC-PASP 1 x 2 passive antenna
splitter kit
RE3-ACC-PASP 1 x 2
passive antenna splitter
kit
▪ Splits two antenna signals into two diversity
receivers
▪ Passes 12 volt booster feed to active antennas or
boosters
▪ Low insertion loss
▪ Ideal companion kit to the RMK2 dual rack mount kit
▪ Also functions as a 2-in x 1-out combiner for sending
two transmitter signals to one antenna
The PASP is a passive antenna splitter kit containing
necessary items when splitting and sharing two
incoming antenna signals between the diversity
antenna jacks of two receivers. An ideal companion kit
to the RMK2 dual rack kit, the PASP takes the signals
collected by the front-mounted antennas on the
RMK2’s CXU2 jacks, and distributes them to the
diversity antenna input jacks on two receivers. Will
adapt any other sources of incoming cable-bound RF
signals via BNC from remote antennas.
Notice!
Requires incoming signals attached via antenna cable (not supplied).
Technical specifications
Net weight: 10.4 oz. (295 g)
Gross weight: 12.7 oz. (360 g)
Dimensions:
RF carrier frequency range:
Impedance: 50 Ω
Insertion loss:
Isolation: 20 dB
VSWR: 1:2
Color: Black
10 - 1,000 MHz
2 dB
PASP
R1
R2
ANT
Passive Antenna Splitter
10 ~ 1000MHz
DC 12V
Booster Power
1
2 3
PASP
R1
R2
ANT
Passive Antenna Splitter
10 ~ 1000MHz
DC 12V
Booster Power
PASP
R1
R2
ANT
Passive Antenna Splitter
10 ~ 1000MHz
DC 12V
Booster Power
RECEIVER 1
RECEIVER 2
Optional CXUF
Optional CXUF
Supplied cables x4
Antenna
A
Antenna
B
2 | RE3-ACC-PASP 1 x 2 passive antenna splitter kit
Installation/configuration notes
1. BNC jack labeled #1 is where the incoming antenna
signal is connected.
The cable connected here should be either a CXUF (as
part of either RMK1 or RMK2 rack kits), or another
BNC-terminated 50 ohm RF cable carrying incoming RF
signal from an antenna.
BNC jack labeled #2 (R1 if referencing the marking on
2.
the PASP module) will connect to receiver 1 via one
of the supplied cables.
This jack will pass DC booster feed thru jack #1 on to
an active booster, and if powering an active booster (RF
amplifier such as RFAMP) that receiver
must be set to on.
3. BNC jack labeled #3 (R2 if referencing the marking on
the PASP module) will connect to receiver 2 via one
of the supplied cables.
These items are repeated on the second PASP module.
Good practice will be to feed antenna A input on each
receiver from one PASP splitter module, and antenna
B input on each receiver from the other PASP splitter
module. See the Patch diagram.
s antenna power
’
The patch diagram shows the typical patching of
signals when front-mounting ½ wave antennas via
CXUF cables found in the RMK2 dual rack kit. The four
cables supplied with the PASP are used to connect the
outputs of the splitters to the four receiver antenna
input jacks. Notice that one antenna feeds RF signal to
antenna A jacks on each receiver, and the other
antenna feeds RF signal to antenna B jacks on each
receiver.
Replacement parts
Order number Description
ESP-EF01U362353 PASP splitter module (1pc)
Compatible products
Order number Description
RE3-ACC-CXUF Rear to front mount antenna cable kit
RE3-ACC-RFAMP Active RF antenna booster; 470-960MHz
RE3-ACC-RMK1
Rack mount kit for single RE3 receiver
RE3-ACC-RMK2 Rack mount kit for two RE3 receivers
RE3-ACC-CXU2 2 foot antenna coax cable (pair)
RE3-ACC-CXU10
10 foot, 50 ohm BNC coax cable (pair)
RE3-ACC-CXU25 25 foot, 50 ohm low loss BNC coax cable
RE3-ACC-CXU50 50 foot, 50 ohm low loss BNC coax cable
RE3-ACC-CXU75
75 foot, 50 ohm low loss BNC coax cable
RE3-ACC-CXU100 100 foot, 50 ohm low loss BNC coax cable
Parts included
Quantity Component
Patch diagram
Represented by:
Germany:
Bosch Sicherheitssysteme GmbH
Robert-Bosch-Ring 5
85630 Grasbrunn
Germany
www.electrovoice.com
© Bosch Security Systems 2018 | Data subject to change without notice
Document Number F.01U.363.718 | Vs1 | 13. Dec 2018
Bosch Security Systems, Inc.
12000 Portland Avenue South
Burnsville MN 55337
USA
2 PASP modules
4 2-foot 50 ohm antenna cables with BNC connectors
1
Engineering datasheet
1 Warranty and product documentation information
card
Ordering information
RE3-ACC-PASP 1 x 2 passive antenna splitter kit
1 x 2 passive antenna splitter kit with two splitter
modules and four antenna cables, black
Order number RE3-ACC-PASP
Loading...