![](/html/b1/b100/b100428538948265c6389b2c7135a9122fb5143cc0fd3cab132893a0f9190e5a/bg1.png)
Electro-Voice | RE3-ACC-CXUF Rear to front mount antenna
FLAT (A)
CXUF
Using RMK2 as example
cable kit
RE3-ACC-CXUF Rear to
front mount antenna
cable kit
▪ Two high-quality RG-58 50
▪ Female flange mount BNC on one end for panel
mounting
▪ Male BNC on other end couples to receiver antenna
input jack
The CXUF is a pair of high quality, low-loss coax cables
intended to relocate a wireless receiver’s antenna
input jacks to the front panel of a 19” rack. The
threaded flange mount connectors fit securely into the
openings of either the RMK1 or RMK2 rack mounting
kits for front-mounting the stock ½ wave antennas or
extension coax cables. The male BNC twist-on
connectors on the other ends securely connect to the
receiver’s antenna A and antenna B RF input jacks.
Ω coax cables
Technical specifications
Cable type: Coaxial
Impedance:
50 Ω
Installation/configuration notes
To install the antenna cables, do the following:
Ensure the receiver is securely mounted with RMK1
1.
or RMK2 rack kit.
2. Remove the locking nut, lock washer, and rubber
insulator from the CXUF threaded flange-mount
connector.
3. While aligning the flat (A) portion of the threaded
connector barrel with the flat portion of the rack ear
front flange opening, slide the threaded barrel
through the opening until it is fully extended through
the rack ear flange. (RMK2 rack ear used for
illustration.)
Length: 1 meter
Connector types: Male BNC twist-on on one end
Female BNC threaded flange mount
on the other end
Color:
Net weight: 2 oz. (57 g)
Gross weight:
Black
2.1 oz. (61 g)
4. Slide the rubber insulator ring onto the threaded
connector barrel.
Slide the lock washer onto the threaded connector
5.
barrel.
![](/html/b1/b100/b100428538948265c6389b2c7135a9122fb5143cc0fd3cab132893a0f9190e5a/bg2.png)
2 | RE3-ACC-CXUF Rear to front mount antenna cable kit
Represented by:
Germany:
Bosch Sicherheitssysteme GmbH
Robert-Bosch-Ring 5
85630 Grasbrunn
Germany
Bosch Security Systems, Inc.
12000 Portland Avenue South
Burnsville MN 55337
USA
www.electrovoice.com
© Bosch Security Systems 2018 | Data subject to change without notice
Document Number F.01U.363.714 | Vs1 | 14. Dec 2018
6. Thread and tighten the nut onto the threaded
connector barrel.
Ensure the nut is tightened securely to the connector
barrel.
Repeat steps 4-7 for the other cable and rack ear.
7.
8. Connect the other ends of the antenna cables into
antenna A and antenna B inputs of the receiver, or an
antenna distribution device such as the RE3-ACCAASP active antenna splitter or RE3-ACC-PASP
passive antenna splitter.
Compatible products
Order number Description
RE3-ACC-RMK1 Rack mount kit for single RE3 receiver
RE3-ACC-RMK2
Rack mount kit for two RE3 receivers
RE3-ACC-CXU2 2 foot antenna coax cable (pair)
RE3-ACC-AASP 2-in x 8-out antenna splitter 470-960MHz
Parts included
Quantity Component
2 CXUF cables
2
Nuts
2 Lock washers
2
Rubber insulator rings
1 Engineering datasheet
1 Warranty and product documentation information
card
Ordering information
RE3-ACC-CXUF Rear to front mount antenna cable kit
BNC to BNC 50Ω rear to front-mount antenna coax
cable kit, black
Order number RE3-ACC-CXUF