Electro-Voice RE3-ACC-AASP Datasheet
Electro-Voice | RE3-ACC-AASP 2-in x 8-out antenna splitter
470-960MHz
RE3-ACC-AASP 2-in x
8-out antenna splitter
470-960MHz
▪ Active 2-in x 8-out antenna splitter
▪ Distributes DC to power four receivers
▪ Splits two antennas into four diversity receivers
▪ Selectable booster feed for powering active
antennas and boosters
▪ Additional cascade output per antenna allows
stacking splitters without sacrificing 2x8 function
The AASP is a professional, wide bandwidth, active
antenna splitter designed to function as the
distribution hub of RF and DC power in a multichannel wireless microphone system. One AASP
actively splits each incoming antenna signal (A and B)
into four connected diversity receivers in the system
without signal loss, as well as distributing DC to
power each of the four connected receivers.
In addition to the four RF outputs per antenna, AASP
also includes a convenient cascade output per antenna
allowing incoming signals to be sent directly to
another AASP unit with zero loss, and without
sacrificing any of the four RF outputs per side. A total
of five AASP splitters can be cascaded from one pair of
antennas.
The selectable booster feed powers active antennas
and/or booster amps with 12V DC. The factory default
setting is on, and should a need arise for the booster
feed to be off, an on/off switch can be accessed on
the main circuit board inside of the chassis.
Third order intercept point: 24 dBm
Impedance:
Input voltage: 12v DC/5A
Output DC voltage: +12V 1A x 4
Antenna booster DC voltage:
Dimensions (length): 18.93" (481mm)
Dimensions (width): 8.94" (227mm)
Dimensions (depth):
Finish: Polyurethane paint, black
Net weight: 6.78 lb (3.07 kg)
Gross weight:
50 Ohm
12V
1.71" (43.4mm)
8.16 lb (3.7 kg)
Technical specifications
Frequency range: 470 - 960 MHz
RF output gain: 3 dB (± 2dB)
Cascade output level:
Output connection isolation: 25dB
0dB - +2dB
AASP
UHF ANTENNA DISTRIBUTIO N SYSTEM
AASP Active Antenna Splitter
D
C Input
12V / 5A
CASCADE
DC Output
DC Output
C
ASCADE
Made in Taiwan
Bosch Security Systems, Inc.
Serial No.
2 In X 8 Out, 470 - 960 MHz
Antenna A
1
2VDC Out
100 mA
Antenna B
12VDC Out
100 mA
481 mm
45 mm
227 mm
AASP Active Antenna Splitter
D
C Input
12V / 5A
CASCADE
DC Output
DC Output
C
ASCADE
Made in Taiwan
Bosch Security Systems, Inc.
Serial No.
2 In X 8 Out, 470 - 960 MHz
Antenna A
1
2VDC Out
100 mA
Antenna B
12VDC Out
100 mA
AASP
UHF ANTEN NA DISTRIBUTION SYSTEM
1
1
3
4
12
5
7
6
8 9
10
11
2
2 | RE3-ACC-AASP 2-in x 8-out antenna splitter 470-960MHz
Dimensions:
Licensing and certification declarations:
IC: This Class B digital apparatus complies with
Canadian ICES-003. Cet appareil numérique de la
classe B est conforme à la norme NMB-003 du Canada.
This device complies with Industry Canada licenseexempt RSS standard(s). Operation is subject to the
following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including
interference that may cause undesired operation of
the device.
Le présent appareil est conforme aux CNR d'Industrie
Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux
conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage
est susceptible d'en compromettre le fonctionnement.
CE and EU: The CE Declaration of Conformity can be
obtained and downloaded from:
www.electrovoice.com
This Equipment is in compliance with CE requirements
and the following directives:
2011/65/EU RoHS Directive
•
• 2012/19/EU WEEE Directive
• 2014/53/EU RED Directive
AU and NZ: This device is in compliance with Cispr32.
1. Antenna mount holes for attaching optional RE3-ACC-CXUF
2. Power status LED
3. Power switch
4. DC power output jacks to power two receivers with supplied
DC power leads
5. Antenna A input jack
Installation/configuration notes
Product identification:
6. Antenna A cascade output jack for sending antenna A signal
directly out to a second AASP antenna A input
7. Four Antenna A output jacks to send signal to four receiver
antenna A input jacks
8. DC power input for supplied external power supply
9. Four Antenna B output jacks to send signal to four receiver
antenna B input jacks
Loading...