Electronics M-1 User Manual

Manifold Pressure (M-1)
Operating and Installation Instructions
OI 0517912
Rev. C: 9/30/97
to install this product and/or the safety of your aircraft.
5/17/91
S/N:
Electronics International Inc. ®
63296 Powell Butte Hwy  Bend, OR 97701  (541) 318-6060  Buy-EI.com
Important Notice
***** MUST READ *****
If you think it is not important to read this manual, you're wrong! This manual contains important installation information that may affect the safety of your air­craft, delay your installation or affect the operation of your instrument. You read this manual prior to installing your instrument. Any deviation from these installation instructions is the sole responsibility of the installer/pilot and may render the STC invalid.
Read the Warranty / Agreement. There is information in the Warranty / Agreement that may alter your decision to install this product. If you do not accept the terms of the Warranty / Agreement, do not install this product. This product may be returned for a refund. Contact Electronics International inc. for
details.
Check that the instrument make and model marked on the side of the instrument and on the invoice are
correct before starting the installation.
Must
Check that the limit information on this instrument matches the published limits in your aircraft's P.O.H. or Flight Manual. Also, this information may be listed in the T.C. Data Sheet for your aircraft. Any AD's and/or STC's may set forth additional limitations on the operation of your engine. The limit informa­tion listed in the AML is for unmodified aircraft and is intended for reference only.
owner's and/or installer's responsibility to determine proper instrument calibration and range markings for your aircraft.
On the front of this instrument you will find a red light marked with the maximum manifold pressure information. If there are any additional red or yellow lights on this instrument, the operating range of these lights can be found on a sticker located on the side of the instrument (see the AML at the back of this manual to decode this information). This instrument designates any "Caution Range" with yellow LEDs, any "Maximum and Minimum Limits" with Red LEDs and the "Safe Operating Range" with green LEDs. The "Safe Operating Range" on this instrument is equivalent to the green "Normal Operating Range" and any unmarked areas on a analog gauge.
It is possible for any instrument to fail thereby displaying inaccurate high, low or jumpy readings. Therefore, you must be able to recognize an instrument failure and you must be proficient in operating your aircraft safely in spite of an instrument failure. If you do not have this knowledge, contact the FAA or a local flight instructor for training.
The pilot must understand the operation of this product before flying the aircraft. Do not allow anyone to operate the aircraft that does not know the operation of this product. Keep the Operating Manual in the
aircraft at all times.
It is the aircraft
Rev. C: 9/30/97*
Contents
Warranty ............................................................................................... 2
Operation Instructions .......................................................................... 3
Instrument:
..................................................................................................................... 3
Analog Display:
.............................................................................................................. 3
Digital Display:
............................................................................................................... 3
Installation Instructions ....................................................................... 4
Important Information and Initial Check Out:
....................................................... 4
Route The Circular Connector:
................................................................................ 5
Route the Power and Ground Wires:
..................................................................... 5
Route the Backlight Wires:
........................................................................................ 5
Route the (Optional) External Warning Control Line: .......................................
6
Install the Instrument in the Panel:
...........................................................................6
Connect the Circular Connector to the Instrument:
.......................................... 6
Connect the Manifold Pressure Line:
...................................................................... 6
Check Instrument Operation:
................................................................................... 7
Wiring Diagram .................................................................................... 8
M-1 Circular Connector ....................................................................... 9
Specifications and Operating Features ................................................ 10
STC Information ................................................................................... 11
1
Warranty / Agreement
Electronics International Inc. warrants this instrument and system components to be free from defects in materials and workmanship for a period of one year from the user invoice date. Electronics Interna­tional Inc. will repair or replace any item under the terms of this Warranty provided the item is returned to the factory prepaid.
1. This Warranty shall not apply to any product that has been repaired or altered by any person other than Electronics International Inc., or that has been subjected to misuse, accident, incorrect wiring, negligence, improper or unprofessional assembly or improper installation by any person. This warranty
does not cover any reimbursement for any persons time for installation, removal, assembly or repair.
Electronics International retains the right to determine the reason or cause for warranty repair.
2. This warranty does not extend to any machine, vehicle, boat, aircraft or any other device to which the Electronics International Inc. product may be connected, attached, interconnected or used in conjunction with in any way.
3. The obligation assumed by Electronics International Inc. under this warranty is limited to repair, replacement or refund of the product, at the sole discretion of Electronics International Inc.
4. Electronics International Inc. is not liable for expenses incurred by the customer or installer due to factory updates, modifications, improvements, upgrades, changes, or any other alterations to the product that may affect the form, fit, function or operation of the product.
5. Personal injury or property damage do to misinterpretation or lack of understanding this product is solely the pilots responsibility. The pilot must understand the operation of this product before flying the aircraft. Do not allow anyone to operate the aircraft that does not know the operation of this product. Keep the Operating Manual in the aircraft at all times.
6. E. I. Inc. is not responsible for shipping charges or damages incurred under this Warranty.
7. No representative is authorized to assume any other liability for Electronics International Inc. in connection with the sale of Electronics International Inc. products.
8. If you do not agree to and accept the terms of this warranty, you may return the product for a
refund.
This Warranty is made only to the original user. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES OR OBLIGATIONS: EXPRESS OR IMPLIED. MANUFACTURER EXPRESSLY DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. PURCHASER AGREES THAT IN NO EVENT SHALL MANUFAC­TURER BE LIABLE FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES, IN­CLUDING LOST PROFITS OR LOSS OF USE OR OTHER ECONOMIC LOSS. EXCEPT AS EXPRESSLY PROVIDED HEREIN, MANUFACTURER DISCLAIMS ALL OTHER LIABILITY TO PURCHASER OR ANY OTHER PERSON IN CONNECTION WITH THE USE OR PERFOR­MANCE OF MANUFACTURERS PRODUCTS, INCLUDING SPECIFICALLY LIABILITY IN TORT.
2
Loading...
+ 8 hidden pages