Electrolux FKGHS01P User Manual

FRONT-LOADING GAS DRYER
Use &Care Guide
For questions about features, operation/performance, parts, accessories or service, call: 1-800-422-1230
In Canada, call for assistance 1-800-461-5681, for installation and service, call: 1-800-807-6777 or visit our website at...
www.kitchenaid.com or www.KitchenAid.ca
SECADORA A GAS DE CARGA FRONTAL
Manual de Usoy Cuidado
Si tiene preguntas respecto a las características, funcionamiento/rendimiento, partes, accesorios o servicio técnico, llame al: 1-800-422-1230
SÉCHEUSE À GAZ À CHARGEMENT À L'AVANT
Guide d’utilisation etd’entretien
Au Canada, pour assistance composez le 1-800-461-5681, pour installation ou service composez le 1-800-807-6777
ou visitez notre site web à... www.KitchenAid.ca
Table of Contents/Índice/Table des matières..................................................................2
Model/Modelo/Modèle KGHS01P
8562593
TABLE OF CONTENTS
DRYER SAFETY..............................................................................3
INSTALLATION INSTRUCTIONS..................................................4
Tools and Parts ............................................................................4
Options.........................................................................................5
Location Requirements ...............................................................5
Electrical Requirements ...............................................................7
Gas Supply Requirements...........................................................7
Venting Requirements..................................................................8
Plan Vent System.........................................................................9
Install Vent System.....................................................................10
Install Leveling Legs...................................................................11
Level Dryer .................................................................................11
Make Gas Connection ...............................................................11
Connect Vent..............................................................................12
Reverse Door Swing ..................................................................12
Complete Installation .................................................................13
DRYER USE ..................................................................................14
Starting Your Dryer.....................................................................14
Stopping Your Dryer ..................................................................15
Pausing or Restarting.................................................................15
Control Locked...........................................................................15
Loading.......................................................................................15
Drying and Cycle Tips................................................................15
Status Lights ..............................................................................16
Cycles.........................................................................................16
Additional Features ....................................................................17
Drying Rack................................................................................18
DRYER CARE ..............................................................................19
Cleaning the Dryer Location ......................................................19
Cleaning the Lint Screen............................................................19
Cleaning the Dryer Interior .........................................................19
Removing Accumulated Lint......................................................19
Vacation and Moving Care.........................................................20
Changing the Drum Light...........................................................20
TROUBLESHOOTING ..................................................................20
ASSISTANCE OR SERVICE.........................................................21
In the U.S.A. ...............................................................................21
In Canada ...................................................................................21
WARRANTY...............................................................................22
ÍNDICE
SEGURIDAD DE LA SECADORA................................................23
INSTRUCCIONES DE INSTALACIÓN.........................................25
Herramientas y piezas................................................................25
Opciones ....................................................................................25
Requisitos de ubicación.............................................................25
Requisitos eléctricos..................................................................27
Requisitos del suministro de gas...............................................28
Requisitos de ventilación...........................................................29
Planificación del sistema de ventilación....................................30
Instalación del sistema de ventilación.......................................31
Instalación de las patas niveladoras..........................................32
Nivelación de la secadora..........................................................32
Conexión del suministro de gas ................................................32
Conexión del ducto de escape..................................................33
Cómo invertir el cierre de la puerta............................................33
Complete la instalación..............................................................34
USO DE LA SECADORA ..............................................................35
Puesta en marcha de la secadora .............................................35
Detención de la marcha de la secadora ....................................36
Pausa o reanudación de la marcha ...........................................36
Control bloqueado .....................................................................36
Cómo cargar...............................................................................36
Sugerencias de ciclos y secado ................................................37
Luces de estado.........................................................................37
Ciclos..........................................................................................38
Características adicionales ........................................................39
Estante de secado......................................................................40
CUIDADO DE LA SECADORA....................................................41
Limpieza del lugar donde está la secadora...............................41
Limpieza del filtro de pelusa ......................................................41
Limpieza del interior de la secadora ..........................................42
Eliminación de pelusa acumulada .............................................42
Cuidado para las vacaciones y la mudanza..............................42
Cambio de la luz del tambor......................................................42
SOLUCIÓN DE PROBLEMAS......................................................43
AYUDA O SERVICIO TÉCNICO...................................................44
GARANTÍA.....................................................................................45
TABLE DES MATIÈRES
SÉCURITÉ DE LA SÉCHEUSE ....................................................46
INSTRUCTIONS D’INSTALLATION.............................................48
Outillage et pièces......................................................................48
Options .......................................................................................48
Emplacement d’installation........................................................49
Spécifications électriques ..........................................................51
Alimentation en gaz....................................................................51
Exigences concernant l’évacuation ...........................................53
Planification du système d'évacuation ......................................53
Installation du conduit d’évacuation..........................................55
Installation des pieds de nivellement.........................................56
Mise à niveau de la sécheuse....................................................56
Raccordement au gaz................................................................56
Conduit d’évacuation .................................................................57
Inversion de l'ouverture de la porte ...........................................57
Achever l’installation ..................................................................58
UTILISATION DE LA SÉCHEUSE................................................59
Mise en marche de la sécheuse ................................................59
Arrêt de la sécheuse...................................................................60
Arrêt ou remise en marche.........................................................60
Verrouillage des commandes.....................................................60
Chargement................................................................................60
Conseils pour le séchage et les programmes ...........................61
Témoins lumineux ......................................................................61
Programmes...............................................................................62
Caractéristiques supplémentaires .............................................63
Grille de séchage........................................................................63
ENTRETIEN DE LA SÉCHEUSE.................................................64
Nettoyage de l'emplacement de la sécheuse ...........................64
Nettoyage du filtre à charpie......................................................64
Nettoyage de l’intérieur de la sécheuse.....................................65
Retrait de la charpie accumulée ................................................65
Précautions à prendre pour les vacances et avant un
déménagement ..........................................................................65
Changement de l’ampoule d’éclairage du tambour..................65
DÉPANNAGE.................................................................................66
ASSISTANCE OU SERVICE.........................................................67
GARANTIE.....................................................................................68
2
DRYER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.
This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
You can be killed or seriously injured if you don't immediately
DANGER
WARNING
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.
WARNING: For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, or to prevent property damage, personal injury, or death.
follow instructions.
can be killed or seriously injured if you don't
You instructions.
follow
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance.
Do not touch any electrical switch; do not use any phone in your building.
Clear the room, building, or area of all occupants.
Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's
instructions. If you cannot reach your gas supplier, call the fire department.
Installation and service must be performed by a qualified installer, service agency, or
the gas supplier.
In the State of Massachusetts, the following installation instructions apply:
Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by
the State of Massachusetts.
If using a ball valve, it shall be a T-handle type.
A flexible gas connector, when used, must not exceed 3 feet.
3
IMPORTANT SAFETY INSTRUCTIONS
WARNING:
including the following:
Read all instructions before using the dryer.
Do not place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may contribute to a chemical reaction that could cause a load to catch fire.
Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry­cleaning solvents, other flammable, or explosive substances as they give off vapors that could ignite or explode.
Do not allow children to play on or in the dryer. Close supervision of children is necessary when the dryer is used near children.
Before the dryer is removed from service or discarded, remove the door to the drying compartment.
Do not reach into the dryer if the drum is moving.
Do not install or store the dryer where it will be exposed to the weather.
Do not tamper with controls.
To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic precautions,
SAVE THESE INSTRUCTIONS
Do not repair or replace any part of the dryer or attempt any servicing unless specifically recommended in this Use and Care Guide or in published user-repair instructions that you understand and have the skills to carry out.
Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product.
Do not use heat to dry articles containing foam rubber or similarly textured rubber-like materials.
Clean lint screen before or after each load.
Keep area around the exhaust opening and adjacent surrounding areas free from the accumulation of lint, dust, and dirt.
The interior of the dryer and exhaust vent should be cleaned periodically by qualified service personnel.
See installation instructions for grounding requirements.
IMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54 or the Canadian Natural Gas and Propane Installation Code, CSA B149.1.
The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA C22.1.
INSTALLATION INSTRUCTIONS
NOTE: Do not use leveling legs if installing the dryer on a
Tools andParts
Check that you have everything necessary for correct installation. Proper installation is your responsibility.
8" or 10" pipe wrench
8" or 10" adjustable
wrench (for gas connections)
Flat-blade screwdriver
Adjustable wrench that
opens to 1" (2.5 cm) or hex-head socket wrench (for adjusting dryer feet)
Level
Parts supplied
Remove parts packages from dryer drum. Check that all parts are included.
4 Leveling legs
¹⁄₄" nut driver or socket
wrench
Knife
Vent clamps
Pipe-joint compound
resistant to L.P. gas
Caulking gun and
compound (for installing new exhaust vent)
Pliers
pedestal.
Parts needed
Check local codes and with gas supplier. Check existing gas supply, electrical supply and venting. Read “Electrical Requirements,” “Gas Supply Requirements and Venting Requirements before purchasing parts.
For close-clearance installations between 31.5" (80.01 cm)
and 37" (93.98 cm), see Plan Vent System section for venting requirements.
37" (93.98 cm)
Mobile home installations require special parts (listed following) that may be ordered by calling the dealer from whom you purchased your dryer. For further information, please refer to the Assistance or Service section of this manual.
Mobile Home Installation Kit. Ask for Part Number 346764.
Metal exhaust system hardware.
4
Options
Pedestal
Are you placing the dryer on a pedestal? You may purchase a pedestal separately for this dryer. This pedestal will add about 13" (33 cm) to the height of your unit for a total height of approximately 51" (130 cm).
Optional pedestal
To order, call the dealer from whom you purchased your dryer or refer to the Assistance or Service section of this manual. Ask for Part Number LAB2700PMT (Meteorite) or LAB2700MQ0 (White).
Stack Kit
Are you planning to stack your washer and dryer? To do so, you will need to purchase a Stack Kit.
To order, call the dealer from whom you purchased your dryer or refer to the Assistance or Service section of this manual. Ask for Part Number 8541503.
For a garage installation, you will need to place the dryer at
least 18" (46 cm) above the floor. If using a pedestal, you will need an additional 6" (15.24 cm).
Do not operate your dryer at temperatures below 45ºF (7ºC). At lower temperatures, the dryer might not shut off at the end of an automatic cycle. This can result in longer drying times.
The dryer must not be installed or stored in an area where it will be exposed to water and/or weather.
Check code requirements. Some codes limit, or do not permit, installation of the dryer in garages, closets, mobile homes, or sleeping quarters. Contact your local building inspector.
NOTE: No other fuel-burning appliance can be installed in the same closet as a dryer.
Installation clearances
The location must be large enough to fully open the dryer
door.
Additional spacing should be considered for ease of
installation and servicing.
Additional clearances might be required for wall, door and
floor moldings.
Additional spacing of 1" (2.5 cm) on all sides of the dryer is
recommended to reduce noise transfer.
Companion appliance spacing should also be considered.
Dryer Dimensions
51½" (130.81 cm)
Location Requirements
WARNING
Explosion Hazard
Keep flammable materials and vapors, such as gasoline, away from dryer.
Place dryer at least 18 inches (46 cm) above the floor for a garage installation.
Failure to do so can result in death, explosion, or fire.
You will need
A location that allows for proper exhaust installation. A gas
dryer must be exhausted to the outdoors. See “Venting Requirements.
A grounded electrical outlet located within 2 ft (61 cm) of
either side of the dryer. See Electrical Requirements.
A sturdy floor to support the total dryer weight of 200 lbs
(90.7 kg). The combined weight of a companion appliance should also be considered.
A level floor with a maximum slope of 1" (2.5 cm) under entire
dryer. If slope is greater than 1" (2.5 cm), install Extended Dryer Feet Kit, Part Number 279810. Clothes may not tumble properly and automatic sensor cycles may not operate correctly if dryer is not level.
38" (96.52 cm)
*31½" (80 cm)
27" (68.6 cm)
*Most installations require a minimum 5½" (14 cm) clearance
behind the dryer for the exhaust vent with elbow. See Venting Requirements.
Minimum installation spacing for custom undercounter installation
The dimensions shown are for the minimum spacing allowed.
Custom undercounter installation - Dryer only
0" (0 cm)
38" min. (96.52 cm)
0" (0 cm)
27" (68.6 cm)
0" (0 cm)
5
Minimum installation spacing for recessed or closet
)
installation, with or without a pedestal
The dimensions shown are for the minimum spacing allowed.
For closet installation, with a door, minimum ventilation
openings in the top and bottom of the door are required. Louvered doors with equivalent ventilation openings are acceptable.
Closet installation - Dryer only
Minimum installation spacing for cabinet installation
The dimensions shown are for the minimum spacing allowed.
For cabinet installation, with a door, minimum ventilation
openings in the top of the cabinet are required.
7" (17.8 cm)
7" (17.8 cm)
0" (0 cm)
31½" (80 cm)
A
14" max. (35.6 cm)
18" min. (45.72 cm)
0" (0 cm)
48 in.
(310 cm2)
24 in.
(155 cm2)
2
2
B
A. Side view - closet or confined area B. Closet door with vents
Recessed or closet installation - Dryer on pedestal
14" max. (35.6 cm)
18" min. (45.72 cm)
3" (7.6 cm)
3" (7.6 cm)
9" (22.9 cm
0"
(0 cm)
31¹₂"
(80.0 cm)
0" (0 cm)
0"
(0 cm)
27"
(68.6 cm)
0" (0 cm)
Mobile home - Additional installation requirements
This dryer is suitable for mobile home installations. The install­ation must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280) or Standard CAN/CSA-Z240 MH.
Mobile home installations require:
Metal exhaust system hardware which is available for
purchase from your dealer.
Mobile home Installation Kit Part Number 346764. See “Tools
and Parts section for ordering information.
Special provisions must be made in mobile homes to
introduce outside air into the dryer. The opening (such as a nearby window) should be at least twice as large as the dryer exhaust opening.
0" (0 cm)
27" (68.6 cm)
0" (0 cm)
0" (0 cm)
31½" (80 cm)
0" (0 cm)
AB
A. Recessed area B. Side view - closet or confined area
6
Electrical Requirements
Gas Supply Requirements
WARNING
Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death,
fire, or electrical shock.
120-Volt, 60-Hz., AC-only, 15- or 20-amp fused electrical
supply is required. A time-delay fuse or circuit breaker is recommended. It is recommended that a separate circuit serving only this dryer be provided.
GROUNDING INSTRUCTIONS
For a grounded, cord-connected dryer: This dryer must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This dryer is equipped with a cord having an equipment­grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
WARNING:
grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative or personnel if you are in doubt as to whether the dryer is properly grounded. Do not modify the plug provided with the dryer: if it will not fit the outlet, have a proper outlet installed by a qualified electrician.
Improper connection of the equipment-
SAVE THESE INSTRUCTIONS
WARNING
Explosion Hazard Use a new AGA or CSA approved gas supply line. Install a shut-off valve. Securely tighten all gas connections. If connected to LP, have a qualified person make sure
gas pressure does not exceed 13" (33 cm) water column.
Examples of a qualified person include: licensed heating personnel,
authorized gas company personnel, and authorized service personnel.
Failure to do so can result in death, explosion, or fire.
Gas Type
Natural gas:
This dryer is equipped for use with natural gas. It is design­certified by CSA International for L.P. (propane or butane) gases with appropriate conversion.
Your dryer must have the correct burner for the type of gas in
your home. Burner information is located on the rating plate in the door well of your dryer. If this information does not agree with the type of gas available, contact your dealer or call the phone numbers referenced in the Assistance or Service section of this manual.
L.P. gas conversion: Conversion must be made by a qualified technician.
No attempt shall be made to convert the appliance from the gas specified on the model/serial rating plate for use with a different gas without consulting the serving gas supplier.
Gas supply line
½" IPS pipe is recommended.
³⁄₈" approved tubing is acceptable for lengths under
20 ft (6.1 m) if local codes and gas supplier permit.
Must include ¹⁄₈" NPT minimum plugged tapping accessible
for test gauge connection, immediately upstream of the gas connection to the dryer (see following illustration).
Must include a shutoff valve:
In the U.S.A.:
An individual manual shutoff valve must be installed within six (6) feet (1.8 m) of the dryer in accordance with the National Fuel Gas Code, ANSI Z223.1.
7
In Canada:
An individual manual shutoff valve must be installed in accordance with the B149.1, Natural Gas and Propane Installation Code. It is recommended that an individual manual shutoff valve be installed within six (6) feet (1.8 m) of the dryer.
The location should be easy to reach for opening and closing.
A
C
E
Dryer gas pipe
The gas pipe that comes out through the rear of your dryer
has a ³⁄₈" male pipe thread.
*6¼" (15.9 cm)
B
B
A.
³⁄₈
"
flexible gas connector
³⁄₈
" pipe to flare adapter fitting
B. C.
¹⁄₈
" NPT plugged tapping
D. ½" NPT gas supply line
E. Gas shutoff valve
D
Gas supply connection requirements
There are many methods by which your gas dryer can be connected to the gas supply. Listed here are some guidelines for two different methods of connection.
Option 1 (Recommended method)
Flexible stainless steel gas connector:
If local codes permit, use a new flexible stainless steel gas
connector (Design Certified by the American Gas Association or CSA International) to connect your dryer to the rigid gas supply line. Use an elbow and a ³⁄₈" flare x ³⁄₈" NPT adapter fitting between the stainless steel gas connector and the dryer gas pipe, as needed to prevent kinking.
Option 2 (Alternate method)
Approved aluminum or copper tubing:
Lengths under 20 ft (6.1 m) can use ³⁄₈" approved tubing
(if codes and gas supplier permit).
If you are using natural gas, do not use copper tubing.
³⁄₈" flare x ³⁄₈" NPT adapter fitting between dryer pipe and
³⁄₈" approved tubing.
Lengths over 20 ft (6.1 m) should use larger tubing and a
different size adapter fitting.
If your dryer has been converted to use L.P. gas, ³⁄₈" L.P.
compatible copper tubing can be used. If the total length of the supply line is more than 20 ft (6.1 m), use larger tubing.
NOTE: Pipe joint compounds that resist the action of L.P. gas must be used. Do not use TEFLON
®†
tape.
A
A. ½" NPT gas supply line
B.
³⁄₈
" NPT dryer pipe
1½" (3.8 cm)
*NOTE: If the dryer is mounted on a pedestal, the gas pipe height
must be an additional 13" (33 cm) from the floor.
Burner input requirements
Elevations up to 10,000 ft (3,048 meters):
The design of this dryer is certified by CSA International for
use at altitudes up to 10,000 ft (3,048 m) above sea level at the B.T.U. rating indicated on the model/serial number plate. Burner input adjustments are not required when the dryer is operated up to this elevation.
Elevations above 10,000 ft (3,048 meters):
When installed above 10,000 ft (3,048 m) a 4% reduction of
the burner B.T.U. rating shown on the model/serial number plate is required for each 1,000 ft (305 m) increase in elevation.
Gas supply pressure testing
The dryer must be disconnected from the gas supply piping
system during pressure testing at pressures greater than ½ psi.
VentingRequirements
WARNING
†®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.
8
Fire Hazard Use a heavy metal vent. Do not use a plastic vent. Do not use a metal foil vent. Failure to follow these instructions can result in death
or fire.
WARNING: To reduce the risk of fire, this dryer MUST BE
EXHAUSTED OUTDOORS. 4" (10.2 cm) heavy metal exhaust vent and clamps must be used.
DURASAFE vent products are recommended. DURASAFE vent products can be purchased from your dealer
or by calling Whirlpool Parts and Accessories. For more information, see the Assistance or Service section of this manual.
The dryer exhaust must not be connected into any gas vent,
chimney, wall, ceiling, or a concealed space of a building.
Do not use an exhaust hood with a magnetic latch.
Do not install flexible metal vent in enclosed walls, ceilings or
floors.
Use clamps to seal all joints. Exhaust vent must not be
connected or secured with screws or other fastening devices which extend into the interior of the duct. Do not use duct tape.
IMPORTANT: Observe all governing codes and ordinances.
Optional exhaust installations
This dryer can be converted to exhaust out the right side, left side, or through the bottom. Contact your local dealer to have the dryer converted.
WARNING
Improper venting can cause moisture and lint to collect indoors, which may result in:
Moisture damage to woodwork, furniture, paint, wall-
paper, carpets, etc.
Housecleaning problems and health problems.
Use a heavy metal vent. Do not use plastic or metal foil vent. Rigid metal vent is recommended to prevent crushing and
kinking. Flexible metal vent must be fully extended and supported when
the dryer is in its final position. Remove excess flexible metal vent to avoid sagging and kinking that can result in reduced airflow and poor performance.
An exhaust hood should cap the vent to prevent rodents and insects from entering the home.
Exhaust hood must be at least 12" (30.5 cm) from the ground or any object that is in the path of the exhaust (such as flowers, rocks or bushes, etc.).
If using an existing vent system, clean lint from the entire length of the system and make sure exhaust hood is not plugged with lint. Replace any plastic or metal foil vent with rigid metal or flexible metal vent.
Plan Vent System
Typical exhaust installations
Typical installations vent the dryer from the rear of the dryer. Other installations are possible.
B
Fire Hazard Cover unused exhaust holes with one of the
following kits: 279818 (white) 280028 (meteorite) Contact your local dealer. Failure to follow these instructions can result in death,
fire, electrical shock, or serious injury.
A
A. Standard rear offset exhaust installation B. Left or right side exhaust installation C. Bottom exhaust installation (Not an option with
pedestal installations.)
B
C
Alternate installations for close clearances
Venting systems come in many varieties. Select the type best for your installation. Two close-clearance installations are shown. Refer to the manufacturers instructions.
A
A. Dryer
B. Elbow C. Wall D. Exhaust hood
C
D E
F G
H
E. Clamps F. Rigid metal or flexible metal vent
G. Vent length necessary to connect elbows
H. Exhaust outlet
AB
A. Over the top installation (also available with one
offset elbow)
B. Periscope installation
9
NOTE: The following kits for close clearance alternate installations are available for purchase. Please see the Assistance or Service section of this manual to order.
Over the top Installation:
Part Number 4396028
Periscope Installation (For use with dryer vent to wall vent
mismatch): Part Number 4396037 - 0" (0 cm) to 18" (45.72 cm)
mismatch Part Number 4396011 - 18" (45.72 cm) to 29" (73.66 cm)
mismatch Part Number 4396014 - 29" (73.66 cm) to 50" (127 cm)
mismatch
Special provisions for mobile home installations
The exhaust vent must be securely fastened to a noncombustible portion of the mobile home structure and must not terminate beneath the mobile home. Terminate the exhaust vent outside.
The angled hood style (shown following) is acceptable.
4" (10.2 cm)
2½" (6.4 cm)
See the exhaust vent length chart that matches your hood type for the maximum vent lengths you can use.
Exhaust systems longer than specified will:
Shorten the life of the dryer.
Reduce performance, resulting in longer drying times and
increased energy usage.
3. Determine the number of elbows you will need. IMPORTANT: Do not use vent runs longer than those
specified in the Vent Length Chart. The following chart helps you determine your maximum vent
length based on the number of 90° turns or elbows you will need and the type of vent (rigid or flexible metal) and hood that you will use.
Vent Length Chart
Determine Vent Length
1. Select the route that will provide the straightest and most
direct path outdoors. Plan the installation to use the fewest number of elbows and turns. When using elbows or making turns, allow as much room as possible. Bend vent gradually to avoid kinking. Avoid 90º turns when possible.
better
2. Determine vent length.
The maximum length of the exhaust system depends upon:
The type of vent (rigid metal or flexible metal).
The number of elbows used.
Type of hood.
Recommended hood styles are shown here.
good
B
Number of 90º turns or elbows
0Rigid metal
1Rigid metal
2Rigid metal
3Rigid metal
4Rigid metal
Type of vent
Flexible metal
Flexible metal
Flexible metal
Flexible metal
Flexible metal
Box or Louvered hoods
64 ft (20 m) 36 ft (11 m)
54 ft (16.5 m) 31 ft (9.4 m)
44 ft (13.4 m) 27 ft (8.2 m)
35 ft (10.7 m) 25 ft (7.6 m)
27 ft (8.2 m) 23 ft (7 m)
Angled hoods
58 ft (17.7 m) 28 ft (8.5 m)
48 ft (14.6 m) 23 ft (7 m)
38 ft (11.6 m) 19 ft (5.8 m)
29 ft (8.8 m) 17 ft (5.2 m)
21 ft (6.4 m) 15 ft (4.6 m)
NOTE: Side and bottom exhaust installations have a 90º turn inside the dryer. To determine maximum exhaust length, add one 90º turn to the chart.
InstallVent System
1. Install exhaust hood. Use caulking compound to seal exterior wall opening around exhaust hood.
2. Connect vent to exhaust hood. Vent must fit inside exhaust hood. Secure vent to exhaust hood with 4" (10.2 cm) clamp.
3.
Run vent to dryer location. Use the straightest path possible. See Determine Vent Length. Avoid 90º turns. Use clamps to seal all joints. Do not use duct tape, screws or other fastening devices that extend into the interior of the vent to secure vent.
10
A
4"
(10.2 cm)
4" (10.2 cm)
A. Louvered hood style B. Box hood style
Install LevelingLegs
D
WARNING
Excessive Weight Hazard Use two or more people to move and install dryer. Failure to do so can result in back or other injury.
1. To protect the floor, use a large flat piece of cardboard from
the dryer carton. Place cardboard under the entire back edge of the dryer. See illustration.
2. Firmly grasp the body of the dryer (not the console panel).
Gently lay the dryer on the cardboard.
3. Examine the leveling legs. Find the diamond marking.
4. Screw the legs into the leg holes by hand. Use a wrench to
finish turning the legs until the diamond marking is no longer visible.
5. Place a carton corner post under each of the 2 dryer back
corners. Stand the dryer up. Slide the dryer on the corner posts until it is close to its final location. Leave enough room to connect the exhaust vent or gas line.
6. Once connection is made and dryer is in final location,
remove corner posts and cardboard.
For mobile home use
Gas dryers must be securely fastened to the floor at the time of installation.
Level Dryer
Check the levelness of the dryer. Check levelness first side to side, then front to back.
If the dryer is not level, prop up the dryer using a wood block. Use a wrench to adjust the legs up or down and check again for levelness.
NOTE: It might be necessary to level the dryer again after it has been moved into its final position.
Make GasConnection
1. Remove the red cap from the gas pipe. Move the dryer close
to its final position.
2. Using a wrench to tighten, connect the gas supply to the
dryer. Use pipe joint compound on all non-flared male threads. If flexible metal tubing is used, be sure there are no kinks.
NOTE: For L.P. gas connections, you must use pipe joint compound resistant to the action of L.P. gas. Do not use TEFLON
A combination of pipe fittings must be used to connect the dryer to the existing gas line. Shown following is a recommended connection. Your connection may be different, according to the supply line type, size and location.
®†
tape.
A
B
A.
³⁄₈
" flexible gas connector
B.
³⁄₈
" dryer pipe
C.
³⁄₈
" to
³⁄₈
D.
" pipe elbow
³⁄₈
" pipe-to-flare adapter fitting
C
Mobile home installations require a Mobile Home Installation Kit. For more information, please reference the service numbers in the Assistance or Service section of this manual.
3. Open the shutoff valve in the supply line. The valve is open
when the handle is parallel to the gas pipe.
A
B
A. Closed valve B. Open valve
4. Test all connections by brushing on an approved
noncorrosive leak-detection solution. Bubbles will show a leak. Correct any leak found.
11
Connect Vent
C
1. Using a 4" (10.2 cm) clamp, connect vent to exhaust outlet in
dryer. If connecting to existing vent, make sure the vent is clean. The dryer vent must fit over the dryer exhaust outlet and inside the exhaust hood. Make sure the vent is secured to exhaust hood with a 4" (10.2 cm) clamp.
2. Move dryer into final position. Do not crush or kink vent.
Make sure dryer is level.
3. (On gas models) Check to be sure there are no kinks in the
flexible gas line.
Reverse DoorSwing
You can change your door swing from a right-side opening to a left-side opening, if desired.
Remove the door
1. Open the dryer door. Remove the 4 screws that hold the door
hinge on the front panel of the dryer. Loosen, but do not remove, the screw with the top keyhole opening last (second from the top).
A
4. Remove the 6 screws to release the outer door assembly
from the inner door assembly (see illustration). It is important that you remove only the 6 indicated screws.
5. Lift the inner door assembly off of the outer door assembly.
Unsnap the handle from the outer door assembly, move it to the other side, and snap in. Set the outer door assembly aside.
B
A. Dryer B. Do not remove C. Dryer door
2. Lift and pull forward on the door so that the keyhole clears
the screw head. Remove the door.
3. Lay the dryer door on a flat, protected surface with the inside
door assembly facing up. Remove the last screw from Step 1. Remove the 2 screws holding the handle to the door.
Reverse the hinge and hinge bracket
1. Place the inner door, screw head side up, on the work
surface.
2. Remove the 4 screws that hold the hinge to the door.
3. Remove the 2 screws that hold the handle bracket to the
door.
12
4. Move hinge to the other side and reattach with the 4 screws
C
removed in Step 2.
5. Move handle bracket to the other side and reattach with the
2 screws removed in Step 3.
6. Set the inner door assembly aside.
Reinstalling the door
1. Check for fingerprints on the glass. Clean if necessary.
2. Place the inner door assembly into the outer door assembly.
Align the hinge in the opening on the side. To fit correctly, the inside door assembly edge is completely inside the outside door assembly edge.
3. Reassemble the inner and outer door assemblies with the
6 screws.
4. Replace the 2 handle screws for the door handle of the door
assembly.
5. Use a small flat-blade screwdriver to remove hole plugs in the
door opening. Slide the head of the screwdriver under the cap of each hole plug, being careful not to scratch the dryer surface. Lift up. Remove the hole plugs in the door opening and insert in the opposite side.
Complete Installation
1. Check to be sure all parts are now installed. If there is an
extra part, go back through the steps to see which step was skipped.
2. Check to be sure you have all of your tools.
3. Dispose of all packaging materials.
4. Check the dryers final location. Be sure the vent is not
crushed or kinked.
5. Check to be sure the dryer is level. See Level Dryer.
6. Plug into a grounded 3 prong outlet. Turn power on.
7. Remove the blue protective film on the console and any tape
remaining on the dryer.
8. Read Dryer Use.
9. Wipe the dryer drum interior thoroughly with a damp cloth to
remove any dust.
10. Set the dryer on a full heat cycle (not an air cycle) for
20 minutes and start the dryer.
If the dryer will not start, check the following:
Dryer is plugged into a grounded 3 prong outlet.
Electrical supply is connected.
House fuse is intact and tight, or circuit breaker has not
tripped.
Dryer door is closed.
11. When the dryer has been running for 5 minutes, open the
dryer door and feel for heat. If you do not feel heat, turn the dryer off and check to see that the gas supply line shutoff valve is open.
If the gas supply line shutoff valve is closed, open it, then
repeat the 5-minute test as outlined above.
If the gas supply line shutoff valve is open, contact a
qualified technician.
6. Insert a screw in the second opening from the top of the
hinge opening and partially tighten. Hang the door by placing the top hinge keyhole over the second screw head and tighten the screw. By putting this screw in first, the door will hang in place while you insert and tighten the remaining 4 screws.
A
A. Dryer door B. Dryer C. Insert this screw first
B
7. Close the door and check that it latches securely.
13
DRYER USE
Starting Your Dryer
WARNING
Explosion Hazard
Keep flammable materials and vapors, such as gasoline, away from dryer.
Do not dry anything that has ever had anything flammable on it (even after washing).
Failure to follow these instructions can result in death, explosion, or fire.
The following is a guide to starting your dryer. Please refer to specific sections of this manual for more detailed information.
1. Clean lint screen before or after each cycle. See “Cleaning
the Lint Screen.
2. Place laundry into dryer and shut door. See Loading.
3. Rotate the dial to select either an Automatic or Manual Cycle
then press the CONTROL ON button. The preset settings and drying time for the cycle chosen will be displayed.
To use an Automatic Cycle
Point the dial to an Automatic Cycle.
Select DRYNESS LEVEL to adjust how dry you want the
load to be. The time displayed is an estimated length of the cycle based on the Dryness Level selected. As the cycle runs, the control senses the dryness of the load and adjusts the time automatically for the selected Dryness Level.
WARNING
Fire Hazard No washer can completely remove oil. Do not dry anything that has ever had any type of oil on
it (including cooking oils). Items containing foam, rubber, or plastic must be dried
on a clothesline or by using an Air Cycle. Failure to follow these instructions can result in death
or fire.
14
NOTE: Time is not adjustable for Automatic Cycles. Pressing the Manual Dry Time (- or +) buttons will cause a triple beep, indicating that the time cannot be changed.
Press the EXTRA CARE feature button if this option is
desired.
Press the CYCLE END SIGNAL button to set signal
volume to desired level.
Press (and hold) HOLD TO START button until dryer starts
(about 1 second).
Once an Automatic cycle has started, the Extra Care feature and the Cycle End Signal level can be adjusted. Press the OFF key twice to stop the dryer and clear the settings, allowing you to select another cycle and Dryness Level.
To use a Manual Cycle
Rotate the dial to select a Manual Cycle.
Press the MANUAL DRY TIME (- or +) buttons until the desired drying time is displayed. Tap - or + and the time will change by 1-minute intervals. Press and hold - or + and the time will change by 5-minute intervals. The initial time displayed is the actual drying time.
Loading
Properly loading your dryer can lower your utility bill and prolong the life of your garments.
Loading suggestions
Load the dryer by the amount of space items take up, not by
their weight.
Do not overload the dryer. This causes wrinkling and uneven
drying.
NOTE: The Manual Dry Time feature can be used only with Manual Cycles.
Press TEMP until the desired temperature glows.
NOTE: Pressing the Dryness Level button will cause the triple beep indicating that this option is not selectable. Also, a Dryness Level is not indicated.
Press the EXTRA CARE feature button if this option is
desired.
Press the CYCLE END SIGNAL button to set volume to
desired level.
Press (and hold) HOLD TO START button until dryer starts
(about 1 second).
While a Manual Cycle is running, you can change the settings for Time, Temperature, the Extra Care feature, and the Cycle End Signal. Press the OFF button twice to stop the dryer and clear the settings, allowing you to select another cycle.
StoppingYour Dryer
To stop your dryer at any time
Press OFF twice or open the door.
Pausing orRestarting
To pause the dryer at any time
Open the door or press OFF once.
To restart the dryer
Close the door and press (and hold) HOLD TO START button until dryer starts.
NOTE: Drying will continue from where the cycle was interrupted if you close the door and press Start within 5 minutes. If the cycle is interrupted for more than 5 minutes, the dryer will shut off. Select new cycle settings before restarting the dryer.
Control Locked
This feature allows you to lock your settings to prevent unintended use of the dryer. You can also use the Control Locked feature to prevent unintended cycle or option changes during dryer operation.
To enable the Control Locked feature when dryer is running:
Press and hold the CYCLE END SIGNAL button for 3 seconds. The control is locked when a single beep is heard and the Control Locked status light is on.
When the dryer is off, it is not necessary to press the Control
On button before activating the Control Locked feature.
To unlock:
Press and hold the CYCLE END SIGNAL button for 3 seconds to turn this feature off.
NOTE: When the dryer is running and Control Locked is on, the dryer can be stopped by pressing the Off button, but cant be restarted until the control is unlocked.
Super Capacity Plus Dryers
Heavy Work Clothes
4 jeans 4 workpants 4 workshirts
Towels
10 bath towels 10 hand towels
Mixed Load
3 sheets (1 king, 2 twin) 4 pillowcases 3 shirts 3 blouses
2 sweatpants 2 sweatshirts
14 washcloths
9 T-shirts 9 shorts 10 handkerchiefs
Drying andCycle Tips
Select the correct cycle and dryness level or temperature for your load. If an Automatic Cycle is running, the display shows the estimated cycle time when your dryer is automatically sensing the dryness level of your load. If a Manual Cycle is running, the display shows the exact number of minutes remaining in the cycle.
Cool Down tumbles the load without heat during the last few minutes of all cycles. Cool Down makes the loads easier to handle and reduces wrinkling. The length of the Cool Down depends on the load size and dryness level.
Drying tips
Follow care label directions when they are available.
If desired, add a fabric softener sheet. Follow package
instructions.
Remove the load from the dryer as soon as tumbling stops to
reduce wrinkling. This is especially important for permanent press, knits, and synthetic fabrics.
Avoid drying heavy work clothes with lighter fabrics. This
could cause overdrying of lighter fabrics, leading to increased shrinkage or wrinkling.
Cycle tips
Dry most loads using the preset cycle settings.
Refer to the Automatic or Manual Preset Cycle Settings chart
(in the “Cycles” section) for a guide to drying various loads.
Drying temperature and Dryness Level are preset when
you choose an Automatic Cycle. You can choose a different dryness level, depending on your load by pressing the DRYNESS LEVEL button to select MORE or LESS.
If you wish to adjust the cycle length of a Manual Cycle,
you must press the MANUAL DRY TIME (- or +) buttons. Adjust the temperature of a Manual Cycle by pressing TEMP until the desired temperature is selected.
NOTE: You cannot choose a Dryness Level with Manual Cycles.
15
StatusLights
You may follow the progress of your dryer with the drying status indicator lights.
Sensing
When a cycle is first turned on, the SENSING light glows until a wet item is detected.
In an Automatic cycle, if a wet item has not been detected
within 10 minutes, the Sensing light will turn off and the dryer will shut down.
In a Manual cycle, if a wet item is not detected after
10 minutes the Wet light turns on and the selected cycle continues.
Cycles
Select the drying cycle that matches the type of load you are drying (see Automatic Preset or Manual Preset Cycle Settings charts).
Cycle control knob
Automatic Cycles
Automatic Cycles allow you to match the cycle to the load you are drying. See the following Automatic Preset Cycle Settings chart. Each cycle dries certain fabrics at the recommended temperature. A sensor detects the moisture in the load and automatically adjusts the drying time for optimal drying.
Wet
The WET light will turn on when a wet item has been detected in the dryer. The Wet light will remain on until:
The damp dry point is reached in an Automatic cycle.
The dryer enters the cool down period in a Manual cycle.
Damp
The DAMP light indicates that the load has reached the damp dry level.
NOTE: The Damp light is not used with manual cycles.
Cool Down
The COOL DOWN light glows during the cool down part of the cycle. Laundry is cooling down for ease in handling.
Cycle Complete
The CYCLE COMPLETE light glows when a drying cycle is finished. If the Extra Care feature has been selected, the Extra Care feature indicator light will also be on.
The Cycle Complete light turns off one hour after the end of a drying cycle (including the Extra Care cycle of 2 hours), when Off is pressed, or when the door is opened.
Extra Care Feature
The EXTRA CARE feature light glows when this option is selected. This indicator stays on with the Cycle Complete light.
Heavy Duty
Use this cycle to get High heat for heavy fabrics such as cotton towels or bedspreads.
Normal
Use this cycle to get Medium heat for drying sturdy fabrics such as work clothes.
Casual
Use this cycle to get Medium heat for drying no-iron fabrics, such as sport shirts, casual business clothes and permanent press blends.
Delicate
Use this cycle to get Low heat for drying synthetic fabrics, washable knit fabrics and no-iron finishes.
Super Delicate
Use this cycle to get Extra Low heat to gently dry items such as lingerie, exercise wear, or sheer curtains.
Control Locked
The CONTROL LOCKED light glows when this option is enabled.
Indicator lights
Other indicator lights on the control panel show Cycle, Temper­ature, and Cycle End Signal settings selected.
The time display will indicate the estimated or actual time remaining in a cycle.
16
Automatic Preset Cycle Settings
Automatic Cycles Load Type
HEAVY DUTY
Heavyweight, towels
NORMAL
Corduroys, work clothes
CASUAL
Permanent press, synthetics
DELICATE
Lingerie, blouses, washable woolens
SUPER DELICATE
Exercise wear, sheer curtains, lace
*Estimated Time with Dryness Level (medium) setting.
Te mp . T im e *
(Minutes)
High 40
Medium 34
Medium 36
Low 28
Extra Low 22
Manual Cycles
Use Manual Cycles to select a specific amount of drying time and a drying temperature. When a Manual Cycle is selected, the ESTIMATED TIME REMAINING display shows the actual time remaining in your cycle. You can change the actual time in the cycle by pressing the Manual Dry Time (- or +) buttons.
Additional Features
Extra Care Feature
When you are unable to remove a load of clothes from the dryer as soon as it stops, wrinkles can form. The Extra Care feature periodically tumbles, rearranges and fluffs the load to avoid wrinkles.
Press the Extra Care feature to get up to 120 minutes of heat-
free, periodic tumbling at the end of a cycle.
Stop at any time by pressing the Extra Care feature or
opening the dryer door.
For the Casual Cycle, the Extra Care feature is preset to “On.
The other Automatic Cycles will retain the Extra Care feature setting. (For example, if you select the Extra Care feature in the Normal cycle, the Extra Care feature will be on the next time you select the Normal cycle.)
NOTE: If you do not select the Extra Care feature, the dryer stops after the cool down period.
Temperature
Temperature settings are used with the Manual Cycles. Press TEMP until the desired temperature setting glows. Temperature settings cannot be used with the Automatic Cycles.
Timed Dry
Use this cycle to complete drying if items are still damp after an Automatic Cycle. Timed Dry is also useful for drying heavyweight and bulky items, such as bedspreads and work clothes.
Touchup
Use this setting to remove wrinkles from items, such as clothes packed in a suitcase or items wrinkled from being left in the dryer too long.
Rapid Dry
Use this cycle for drying small loads or loads that need a short drying time.
Manual Preset Cycle Settings
Manual Cycles Load Type
TIMED DRY
Heavyweight, bulk, bedspreads, work clothes
TOUCHUP Remove wrinkles
RAPID DRY
Small loads
Temp. Default Time
(Minutes)
High 40
Medium 20
High 27
Air Only
Use the Air Only setting for items that require drying without heat such as rubber, plastic and heat-sensitive fabrics. This chart shows examples of items that can be dried using Air Only.
Type of Load Time*
Foam rubber - pillows, padded bras, stuffed toys
Plastic - Shower curtains, tablecloths 20 - 30
Rubber-backed rugs 40 - 50
Olefin, polypropylene, sheer nylon 10 - 20
*Reset time to complete drying, if needed.
(Minutes)
20 - 30
When using Air Only
Check to see that coverings are securely stitched.
Shake and fluff pillows by hand periodically during the cycle.
Dry item completely. Foam rubber pillows are slow to dry.
NOTE: Automatic Cycles are not available when using the Air Only setting.
17
Cycle End Signal
The Cycle End Signal produces an audible sound when the drying cycle is finished. Promptly removing clothes at the end of the cycle reduces wrinkling.
Press and release the CYCLE END SIGNAL to adjust the sound level or turn off the signal.
NOTE: When the Extra Care feature is selected and the Cycle End Signal is on, an audible sound will emit every 5 minutes until the clothes are removed, or the Extra Care feature is finished.
Drying Rack
The drying rack is useful for drying items you would not necessarily want to tumble dry or that you would normally line dry (for example, sweaters).
To use the drying rack
Do not remove the lint screen.
1. Open dryer door.
3. Put the wet items on top of the rack. Leave space between
the items so air can reach all the surfaces.
NOTE: Do not allow items to hang over the edge of the rack.
4. Close the door.
5. Select a timed drying cycle and temperature, or an air cycle
(see following chart). Items containing foam, rubber, or plastic must be dried on a clothesline or by using the Air Only temperature setting.
6. You must select a time by pressing the MANUAL DRY TIME
(- or +) buttons. Reset time as needed to complete drying. Refer to the following table.
7. Press (and hold) HOLD TO START button (about 1 second). NOTE: You must remove rack for normal tumbling. Do not use
automatic cycles with the drying rack. This chart shows examples of items that can be rack dried and
the suggested cycle, temperature setting and drying time. Actual drying time will depend on the amount of moisture items hold.
Rack Dry Setting Temp. Time*
Wool Sweaters
Block to shape and lay flat on the rack
Timed Dry
Low 60
A
A. Front edge
2. Place drying rack inside dryer drum, positioning the back wire
on the ledge of the inner dryer back panel. Push down on front edge of drying rack to secure over the lint screen.
A
A. Dryer back panel
Stuffed toys or pillows
Cotton or polyester fiber filled
Stuffed toys or pillows
Foam rubber filled
Sneakers or canvas shoes Timed
*(Minutes) Reset time to complete drying, if needed.
Timed Dry
Timed Dry
Dry
Low 60
Air Only (no heat)
Air Only (no heat)
90
90
18
DRYER CARE
Cleaning theDryer Location
Keep dryer area clear and free from items that would obstruct the flow of combustion and ventilation air.
WARNING
Explosion Hazard
Keep flammable materials and vapors, such as gasoline, away from dryer.
Place dryer at least 18 inches (46 cm) above the floor for a garage installation.
Failure to do so can result in death, explosion, or fire.
Cleaning the LintScreen
As needed cleaning
Laundry detergent and fabric softener residue can build up on the lint screen. This buildup can cause longer drying times for your clothes, or cause the dryer to stop before your load is completely dry. The screen is probably clogged if lint falls off the screen.
Clean the lint screen with a nylon brush every 6 months, or more frequently, if it becomes clogged due to a residue buildup.
To wash
1. Roll lint off the screen with your fingers.
2. Wet both sides of lint screen with hot water.
3. Wet a nylon brush with hot water and liquid detergent. Scrub
lint screen with the brush to remove residue buildup.
4. Rinse screen with hot water.
5. Thoroughly dry lint screen with a clean towel. Replace screen
in dryer.
Every load cleaning
The lint screen is located in the door opening of the dryer. Clean it before or after each load. A screen blocked by lint can increase drying time.
To clean
1. Pull the lint screen straight up. Roll lint off the screen with
your fingers. Do not rinse or wash screen to remove lint. Wet lint is hard to remove.
2. Push the lint screen firmly back into place. IMPORTANT:
Do not run the dryer with the lint screen loose, damaged,
blocked, or missing. Doing so can cause overheating and damage to both the dryer and fabrics.
Some towels made of synthetic fibers and natural fibers
(polyester and cotton blends) may shed more lint than other towels, causing your dryer’s lint screen to fill up faster. Be sure to remove lint from the lint screen before and after drying new towels.
If lint falls off the screen into the dryer during removal, check
the exhaust hood and remove the lint. See “Vent ing Requirements.
Cleaning theDryer Interior
To clean dryer drum
1. Make a paste with powdered laundry detergent and very
warm water.
2. Apply paste to a soft cloth. OR
Apply a liquid, nonflammable household cleaner to the stained area and rub with a soft cloth until all excess dye and stains are removed.
3. Wipe drum thoroughly with a damp cloth.
4. Tumble a load of clean cloths or towels to dry drum.
NOTE: Garments which contain unstable dyes, such as denim
blue jeans or brightly colored cotton items, may discolor the dryer interior. These stains are not harmful to your dryer and will not stain future loads of clothes. Dry unstable dye items inside out to prevent dye transfer.
Removing AccumulatedLint
From Inside the Dryer Cabinet
Lint should be removed every 2 years or more often, depending on dryer usage. Cleaning should be done by a qualified person.
From the Exhaust Vent
Lint should be removed every 2 years, or more often, depending on dryer usage.
19
Vacation andMoving Care
Vacation care
Operate your dryer only when you are at home. If you will be on vacation or not using your dryer for an extended period of time, you should:
1. Unplug dryer or disconnect power.
2. Close shutoff valve in gas supply line.
3. Wash lint screen.
Moving care
1. Unplug the power supply cord.
2. Close shutoff valve in gas supply line.
3. Disconnect gas supply line pipe and remove fittings attached
to dryer pipe.
4. Cap the open fuel supply line.
5. Make sure leveling legs are secure in dryer base.
6. Use masking tape to secure dryer door.
The dryer light automatically turns on inside the dryer drum when you open the door.
To change the drum light
1. Unplug dryer or disconnect power.
2. Open the dryer door. Locate the light bulb cover on the back
wall of the dryer. Remove the screw located in the lower right corner of the cover. Remove the cover.
3. Turn bulb counterclockwise. Replace the bulb with a 10-watt appliance bulb only. Replace the cover and secure with the screw.
4. Plug in dryer or reconnect power.
Changing theDrum Light
TROUBLESHOOTING
First try the solutions suggested here and possibly avoid the cost of a service call...
Dryer displaying code message
“PF (power failure), check the following:
Was the drying cycle interrupted by a power failure? Press (and hold) HOLD TO START button to restart the dryer.
E Variable (E1, E2, E3) service codes:
Call for service.
Clothes are not drying satisfactorily
Check the following:
Is the lint screen clogged with lint? Is the exhaust vent or outside exhaust hood clogged with lint,
restricting air movement? Run the dryer for 5-10 minutes. Hold your hand under the outside exhaust hood to check air movement. If you do not feel air movement, clean exhaust system of lint or replace exhaust vent with heavy metal or flexible metal vent. See “Installation Instructions.
Is the exhaust vent crushed or kinked? Replace with a heavy metal or flexible metal vent. See Installation Instructions.
Has a fuse blown, or has a circuit breaker tripped? Has an air cycle been selected? Select the right cycle for the
types of garments being dried. See “Cycles.” Is the automatic cycle ending early? The load may not be
contacting the electronic sensor strips, level the dryer. Is the valve open on the gas supply line? Are fabric softener sheets blocking the grille? Use only one
fabric softener sheet and only use it once.
Is the dryer located in a room with temperature below
45ºF (7ºC)?
Proper operation of dryer cycles requires temperatures above 45ºF (7ºC).
Was a cold rinse water used? Was the load very wet?
Expect longer drying times with items rinsed in cold water and with items that hold moisture (cottons).
Is the load too large and heavy to dry quickly?
Separate the load to tumble freely.
Dryer will not run
Check the following:
Is the power cord plugged in? Has a fuse blown, or has a circuit breaker tripped? Was a regular fuse used? Use a time-delay fuse. Is the dryer door firmly closed? Was HOLD TO START firmly pressed and held for at least
1 second? Is a cycle selected?
Unusual sounds
Has the dryer had a period of non-use?
If the dryer hasnt been used for a while, there may be a thumping sound during the first few minutes of operation.
The gas valve clicking is a normal operating sound.
Lint on load
Is the lint screen clogged?
Clean lint screen. Check for air movement.
Is load properly sorted?
Sort lint givers (towels, chenille) from lint takers (corduroy, synthetics). Also sort by color.
Is the load too big or too heavy?
Dry smaller loads so lint can be carried to the lint screen.
Was the load overdried?
Use correct dryer settings for load type. See “Cycles.” Overdrying can cause lint-attracting static electricity.
Was paper or tissue left in pockets?
Is pilling being mistaken for lint?
Pilling (surface fuzz) is caused by normal wear and laundering.
20
Stains on load or color change
Loads are wrinkled
Was dryer fabric softener properly used?
Add dryer fabric softener sheets at the beginning of the cycle when the load is cold. Do not add fabric softener sheets to a warm load.
Were items soiled when placed in the dryer?
Items should be clean before being dried.
Were items properly sorted?
Sort light colors from dark colors. Sort colorfast items from noncolorfast items.
Items shrinking
Was the dryer overloaded?
Dry smaller loads that can tumble freely.
Did the load overdry?
Check the manufacturers care label. Match dryer setting to load type. See “Cycles.”
ASSISTANCE OR SERVICE
Before calling for assistance or service, please check Troubleshooting. It may save you the cost of a service call. If you still need help, follow the instructions below.
When calling, please know the purchase date and the complete model and serial number of your appliance. This information will help us to better respond to your request.
If you need replacement parts
If you need to order replacement parts, we recommend that you use only factory specified replacement parts. Factory specified parts will fit right and work right because they are made with the same precision used to build every new KITCHENAID appliance.
To locate factory specified parts in your area, call our Customer Interaction Center telephone number or your nearest designated service center.
In the U.S.A.
Call the KitchenAid Customer Interaction Center toll free: 1-800-422-1230.
Our consultants provide assistance with:
Features and specifications on our full line of appliances.
Installation information.
Use and maintenance procedures.
Accessory and repair parts sales.
Specialized customer assistance (Spanish speaking, hearing
impaired, limited vision, etc.).
Referrals to local dealers, repair parts distributors, and
service companies. KitchenAid designated service technicians are trained to fulfill the product warranty and provide after-warranty service, anywhere in the United States.
To locate the KitchenAid designated service company in your area, you can also look in your telephone directory Yellow Pages.
®
Was load removed from dryer at the end of the cycle?
Was dryer overloaded?
Dry smaller loads that can tumble freely.
Did load overdry?
Check the manufacturers care label. Match dryer setting to load type. See “Cycles.”
Odors
Have you recently been painting, staining or varnishing in
the area where your dryer is located?
If so, ventilate the area. When the odors or fumes are gone from the area, rewash and dry the clothing.
Garment damage
Check the following:
Were zippers, snaps, and hooks left open? Were strings and sashes tied to prevent tangling? Were care label instructions followed? Were items damaged before drying?
For further assistance
If you need further assistance, you can write to KitchenAid with any questions or concerns at:
KitchenAid Brand Home Appliances Customer Interaction Center 553 Benson Road Benton Harbor, MI 49022-2692
Please include a daytime phone number in your correspondence.
In Canada
For product related questions, please call the KitchenAid Canada Customer Interaction Center toll free: 1-800-461-5681 Monday to Friday 8:00 a.m. - 6:00 p.m. (EST). Saturday 8:30 a.m. - 4:30 p.m. (EST).
Our consultants provide assistance with:
Features and specifications on our full line of appliances.
Referrals to local dealers.
For parts, accessories and service in Canada
Call 1-800-807-6777. KitchenAid designated service technicians are trained to fulfill the product warranty and provide after­warranty service, anywhere in Canada.
For further assistance
If you need further assistance, you can write to KitchenAid Canada with any questions or concerns at:
Customer Interaction Center KitchenAid Canada 1901 Minnesota Court Mississauga, Ontario L5N 3A7
Please include a daytime phone number in your correspondence.
21
Loading...
+ 47 hidden pages