|
|
|
|
|
|
|
|
|
|
EN FRONT LOAD DRYER |
|
INSTALLATION INSTRUCTIONS |
||
FR SÉCHEUSE Á CHARGEMENT FRONTAL |
|
INSTRUCTIONS D’INSTALLATION |
||
ES SECADORA DE CARGA FRONTAL |
|
INSTRUCCIONES DE INSTALACIÓN |
A04173601A August 2015
2Important Safety Instructions
WARNING
For your safety the information in this manual must be followed to minimize the risk of fi re or explosion or to prevent property damage, personal injury or loss of life. Do not store or use gasoline or other fl ammable vapors and liquids in the vicinity of this or any other appliance.
Recognize safety symbols, words and labels
Safety items throughout this manual are labeled with a WARNING or CAUTION based on the risk type as described:
This symbol alerts you to situations that may cause serious body harm, death or property damage.
This symbol alerts you to situations that may cause bodily injury or property damage.
WARNING - RISK OF FIRE
Read all of the following instructions before installing and using this appliance:
•Destroy the carton and plastic bags after the dryer is unpacked. Children might use them for play. Cartons covered with rugs, bedspreads, or plastic sheets can become airtight chambers causing su ocation. Place all materials in a garbage container or make materials inaccessible to children.
•Clothes dryer installation and service must be performed by a qualifi ed installer, service agency or the gas supplier.
•Install the clothes dryer according to the manufacturer’s instructions and local codes.
•The electrical service to the dryer must conform with local codes and ordinances and the latest edition of the National Electrical Code, ANSI/NFPA 70, or in Canada, the Canadian electrical code C22.1 part 1.
•The gas service to the dryer must conform with local codes and ordinances and the latest edition of the National Fuel Gas Code ANSI Z223.1/NFPA 54, or in Canada, thw Natural Gas and Propane Installation Code, CSA B149.1. An individual manual shut-o valve must be installed within 6 ft (1.83 m) of the dryer in accordance with the National Fuel Gas Code, ANSI Z223.1/NFPA 54.
•The dryer is designed under ANSI Z 21.5.1 or ANSI/UL 2158 - CAN/CSA C22.2 No. 112 (latest editions) for HOME USE only. This dryer is not recommended for commercial applications such as restaurants, beauty salons, etc.
•Do not install a clothes dryer with fl exible plastic or fl exible foil venting material. Flexible venting materials are known to collapse, be easily crushed and trap lint. These conditions will obstruct clothes dryer airfl ow and increase the risk of fi re.
•Do not stack a dryer on top of washer already installed on pedestal. Do not stack washer on top of dryer. Do not stack washer on top of another washer.
•The instructions in this manual and all other literature included with this dryer are not meant to cover every possible condition and situation that may occur. Good safe practice and caution MUST be applied when installing, operating and maintaining any appliance.
Save these instructions for future reference.
Table of contents
Important Safety Instructions |
.....................................2 |
Reversing Door.......................................................... |
18-19 |
Installation Requirements........................................ |
3-9 |
Options ............................................................................. |
20 |
Installation Instructions.......................................... |
10-17 |
|
|
©2015 Electrolux Major Appliances |
All rights reserved. |
Installation Requirements |
3 |
Please read and save this guide
Thank you for choosing Electrolux, the premium brand in home appliances. These Installation Instructions are part of our commitment to customer satisfaction and product quality throughout the life of your new appliance.
Questions?
For toll-free telephone support in the U.S.: 1-877-4ELECTROLUX (1-877-435-3287) and in Canada: 1-800-265-8352.
For online support and product information visit www.electroluxappliances.com.
Installation Checklist
Exhaust Venting
Free-fl owing, clear of lint buildup
4 inch (102 mm) rigid or semi-rigid ducting of minimal length and turns
NO foil or plastic venting material
Approved vent hood exhausted to outdoors
240v Electric Supply (Electric Dryer)
Approved NEMA 10-30 or 14-30 service cord with all screws tight on terminal block
Approved strain relief installed
Terminal access cover installed before initial operation
Leveling
Dryer is level, side-to-side and front-to- back
Cabinet is setting solid on all corners
Gas Supply (Gas Dryer)
Manual shuto valve present in supply
All connections sealed with approved sealer and wrench tight
Conversion kit for LP system
Gas supply turned on
No leaks present at all connections - check with soapy water, NEVER check with flame
Tools and materials needed for installation:
Adjustable |
Phillips, straight, & |
Adjustable Optional universal |
||
pliers |
square bit screwdrivers wrench |
accessory |
||
|
|
|
|
wrench |
|
|
or |
|
or |
|
|
|
|
|
Pipe wrench |
LP-resistant |
Carpenter’s level |
External |
|
for gas |
|
thread tape |
|
vent hood |
supply |
|
(for natural gas |
|
|
|
|
or LP supply) |
|
|
Door Reversal
Follow detailed instructions in this guide
Test hinge and latch for function
Electrical Power
House power turned on
Dryer plugged in
Final Checks
Installation Instructions and Use and Care Guide read thoroughly
Door latches and drum tumbles when cycle starts
Registration card sent in
WARNING
FIRE HAZARD
●Failure to follow safety warnings exactly could result in serious injury, death, or property damage.
●Do not install a booster fan in dryer exhaust duct.
●Install all clothes dryers in accordance with the installation instructions in this manual.
|
4 inch rigid metal or |
3-wire or 4-wire |
|
|
240 volt cord kit |
||
semi-rigid metal exhaust duct work |
(electric dryer) |
||
4 in. |
gas line |
½” NPT union flare |
|
adapters (x2) and |
Metal foil tape |
||
(10.2 cm) |
shutoff valve |
flexible gas supply line |
|
clamp |
(gas dryer) |
(gas dryer) |
(not duct tape) |
|
|
|
|
4Installation Requirements
Electrical system requirements
NOTE
Because of potentially inconsistent voltage capabilities, the use of this dryer with power created by gas powered generators, solar powered generators, wind powered generators or any other generator other than the local utility company is not recommended.
ELECTRICAL REQUIREMENTS FOR ELECTRIC DRYER:
CIRCUIT - Individual 30 amp. branch circuit fused with 30 amp. time delay fuses or circuit breakers. Use separately fused circuits for washer and dryer. DO NOT operate a washer and a dryer on the same circuit.
POWER SUPPLY - 3-wire or 4-wire, 120/240 volt, single phase, 60 Hz, Alternating Current.
NOTE
A 120/208 volt, single phase, 60 Hz, Alternating Current supply may be used on dryers marked for use on the rating plate.
IMPORTANT
This dryer is internally grounded to neutral unless it was manufactured for sale in Canada.
Only a 4-conductor cord shall be used when the appliance is installed in a location where grounding through the neutral conductor is prohibited. Grounding through the neutral link is prohibited for: (1) new branch circuit installations, (2) mobile homes, (3) recreational vehicles, and (4) areas where local codes do not permit grounding through the neutral.
3-WIRE POWER SUPPLY CORD (not supplied)
3-wire receptacle (NEMA type 10-30R)
The dryer MUST employ a 3-conductor power supply cord NEMA 10-30 type SRDT rated at 240 volt AC minimum, 30 amp, with 3 open end spade lug connectors with upturned ends or closed loop connectors and marked for use with clothes dryers. For 3-wire cord connection instructions see ELECTRICAL CONNECTIONS FOR A 3-WIRE SYSTEM.
OUTLET RECEPTACLE - NEMA 10-30R receptacle to be located so the power supply cord is accessible when the dryer is in the installed position.
GROUNDING CONNECTION - See “Grounding requirements” in Electrical Installation section.
4-WIRE POWER SUPPLY CORD (not supplied)
4-wire receptacle (NEMA type 14-30R)
The dryer MUST employ a 4-conductor power supply cord NEMA 14-30 type SRDT or DRT (as required) rated at 240 volt AC minimum, 30 amp, with 4 open end spade lug connectors with upturned ends or closed loop connectors and marked for use with clothes dryers. For 4-wire cord connection instructions see ELECTRICAL CONNECTIONS FOR A 4-WIRE SYSTEM.
NOTE
Dryers manufactured for sale in Canada have factory-installed, 4-wire power supply cord (NEMA 14-30).
OUTLET RECEPTACLE - NEMA 14-30R receptacle to be located so the power supply cord is accessible when the dryer is in the installed position.
GROUNDING CONNECTION - See “Grounding requirements” in Electrical Installation section.
ELECTRICAL REQUIREMENTS FOR GAS DRYER:
CIRCUIT - Individual, properly polarized and grounded 15 amp. branch circuit fused with 15 amp. time delay fuse or circuit breaker.
POWER SUPPLY - 2-wire, with ground, 120 volt, single phase, 60 Hz, Alternating Current.
POWER SUPPLY CORD - The dryer is equipped with a 120 volt 3-wire power cord.
GROUNDING CONNECTION - See “Grounding requirements” in Electrical Installation section.
Grounding type wall receptacle
Do not, under
any circumstances, cut, remove,
or bypass the grounding prong.
Power cord with 3-prong grounded plu
Installation Requirements |
5 |
Gas supply requirements
WARNING
EXPLOSION HAZARD
Uncoated copper tubing will corrode when subjected to natural gas, causing gas leaks. Use ONLY black iron, stainless steel, or plasticcoated brass piping for gas supply.
1.Installation MUST conform with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1 (latest edition).
2.The gas supply line should be 1/2 inch (1.27 cm) pipe.
3.If codes allow, fl exible metal tubing may be used to connect your dryer to the gas supply line. The tubing MUST be constructed of stainless steel or plastic-coated brass.
4.The gas supply line MUST have an individual shuto valve installed in accordance with the B149.1, Natural Gas and Propane Installation Code.
5.A 1/8 inch (0.32 cm) N.P.T. plugged tapping, accessible for test gauge connection, MUST be installed immediately upstream of the gas supply connection to the dryer.
6.The dryer MUST be disconnected from the gas supply piping system during any pressure testing of the gas supply piping system at test pressures in excess of 1/2 psig (3.45 kPa).
7.The dryer MUST be isolated from the gas supply piping system during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig (3.45 kPa).
8.Connections for the gas supply must comply with the Standard for Connectors for Gas Appliances, ANSI Z21.24/CSA 6.10.
Exhaust system requirements
Use only 4 inch (102 mm) diameter (minimum) rigid or fl exible metal duct and approved vent hood which has a swing-out damper(s) that open when the dryer is in operation. When the dryer stops, the dampers automatically close to prevent drafts and the entrance of insects and rodents. To avoid restricting the outlet, maintain a minimum of 12 inches (30.5 cm) clearance between the vent hood and the ground or any other obstruction.
WARNING
FIRE HAZARD
Failure to follow these instructions can create excessive drying times and fi re hazards.
The following are specific requirements for proper and safe operation of your dryer.
WARNING
FIRE HAZARD
Do not install a clothes dryer with fl exible plastic or metal foil venting materials. Flexible venting materials are known to collapse, be easily crushed and trap lint. These conditions will obstruct clothes dryer airfl ow and increase the risk of fi re.
CORRECT |
CORRECT |
INCORRECT |
INCORRECT |
If your present system is made up of plastic duct or metal foil duct, replace it with a rigid or semirigid metal duct. Also, ensure the present duct is free of any lint prior to installing dryer duct.
6Installation Requirements
Exhaust system requirements, continued
WARNING
FIRE HAZARD
A clothes dryer must be exhausted outdoors. Do not exhaust dryer into a chimney, a wall, a ceiling, an attic, a crawl space or any concealed space of a building. A clothes dryer produces combustible lint. If the dryer is not exhausted outdoors, some fi ne lint
will be expelled into the laundry area. An accumulation of lint in any area of the home can create a health and fi re hazard.
The dryer must be connected to an exhaust outdoors. Regularly inspect the outdoor exhaust opening and remove any accumulation of lint around the outdoor exhaust opening and in the surrounding area.
WARNING
FIRE HAZARD
●Do not allow combustible materials (for example: clothing, draperies/curtains, paper) to come in contact with exhaust system. The dryer MUST NOT be exhausted into a chimney, a wall, a ceiling, or any concealed space of a building which can accumulate lint, resulting in a fi re hazard.
●Do not screen the exhaust ends of the vent system, or use any screws, rivets or other fasteners that extend into the duct to assemble the exhaust system. Lint can become caught in the screen, on the
screws or rivets, clogging the duct work and creating a fi re hazard as well as increasing drying times. Use an approved vent hood to terminate the duct outdoors, and seal all joints with metal foil tape. All male duct pipe fi ttings MUST be installed downstream with the fl ow of air.
WARNING
FIRE HAZARD
Exceeding the length of duct pipe or number of elbows allowed in the “MAXIMUM LENGTH” charts can cause an accumulation of lint in the exhaust system. Plugging the system could create a fi re hazard, as well as increase drying times.
|
|
MAXIMUM LENGTH |
|
<![if ! IE]> <![endif]>Number |
of 4” (102 mm) Rigid Metal Duct |
||
|
VENT HOOD TYPE |
|
|
(Preferred) |
|
||
<![if ! IE]> <![endif]>turns 90° of |
|
|
2.5” |
4” |
|
|
|
(10.2 cm) |
louvered |
(6.35 cm) |
|
0 |
125 ft. (38 m) |
110 ft. (33.5 m) |
|
1 |
115 ft. (35 m) |
100 ft. (30.5 m) |
|
2 |
105 ft. (32 m) |
90 ft. (27.5 m) |
|
3 |
95 ft. (29 m) |
80 ft. (24.5 m) |
|
4 |
85 ft. (26 m) |
70 ft. (21.5 m) |
WARNING
FIRE HAZARD
●Do not install fl exible plastic or fl exible foil venting material.
●If installing semi-rigid venting, do not exceed 8 ft. (2.4 m) duct length.
EXHAUST DIRECTION
Directional exhausting can be accomplished by installing a quick-turn 90° dryer vent elbow directly to exhaust outlet of dryer. Dryer vent elbows are available through your local parts distributor or hardware store.
See also CLEARANCE REQUIREMENTS on the next page.
NOTE
Use of 90° quickturn elbow required to meet minimum installation depth.
Installation Requirements |
7 |
Exhaust system requirements, continued
WARNING
FIRE HAZARD
Do not install the dryer where gasoline or other fl ammables are kept or stored. If the dryer is installed in a garage, it must be a minimum of 18 inches (45.7 cm) above the fl oor. Failure to do so can result in death, explosion, fi re or burns.
Install male fittings in correct direction:
CORRECT |
INCORRECT |
In installations where the exhaust system is not described in the charts, the following method must be used to determine if the exhaust system is acceptable:
1.Connect an inclined or digital manometer between the dryer and the point the exhaust connects to the dryer.
2.Set the dryer timer and temperature to air fl u (cool down) and start the dryer.
3.Read the measurement on the manometer.
4.The system back pressure MUST NOT be higher than 1.0 inch of water column. If the system back pressure is less than 1.0 inch of water column, the system is acceptable. If the manometer reading is higher than 1.0 inch of water column, the system is too restrictive and the installation is unacceptable.
Although vertical orientation of the exhaust system is acceptable, certain extenuating circumstances could a ect the performance of the dryer:
●Only the rigid metal duct work should be used.
●Venting vertically through a roof may expose the exhaust system to down drafts causing an increase in vent restriction.
●Running the exhaust system through an uninsulated area may cause condensation and faster accumulation of lint.
●Compression or crimping of the exhaust system will cause an increase in vent restriction.
●The exhaust system should be inspected and cleaned a minimum of every 18 months with normal usage. The more the dryer is used, the more often you should check the exhaust system and vent hood for proper operation.
Manufactured or mobile home installation
1.Installation MUST conform to current Manufactured Home Construction & Safety Standard, Title 24 CFR, Part 32-80 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280) or Standard CAN/CSAZ240 MH.
2.Dryer MUST be exhausted outside (outdoors, not beneath the mobile home) using metal ducting that will not support combustion. Metal ducting must be 4 inches (10.16 cm) in diameter with no obstructions. Rigid metal duct is preferred.
3.If dryer is exhausted through the fl oor and area beneath the mobile home is enclosed, the exhaust system MUST terminate outside
the enclosure with the termination securely fastened to a non-combustible portion of the mobile home structure.
4.Refer to previous sections in this guide for other important exhaust venting system requirements.
5.When installing a gas dryer into a mobile home, a provision must be made for outside make up air. This provision is to be not less than twice the area of the dryer exhaust outlet.
6.Installer MUST anchor this (1) dryer or (2) dryer mounted on pedestal to the fl oor with approved Mobile Home Installation Kit - P/N 137067200.
8Installation Requirements
Clearance requirements
IMPORTANT
DO NOT INSTALL YOUR DRYER:
1.In an area exposed to dripping water or outside weather conditions.
2.In an area where it will come in contact with curtains, drapes, or anything that will obstruct the fl ow of combustion and ventilation air.
3.On carpet. Floor MUST be solid with a maximum slope of 1 inch (2.5 cm).
INSTALLATION IN A RECESS OR CLOSET
1.A dryer installed in a bedroom, bathroom, recess or closet, MUST be exhausted outdoors.
2.No other fuel burning appliance shall be installed in the same closet as the gas dryer.
3.Your dryer needs the space around it for proper ventilation.
DO NOT install your dryer in a closet with a solid door.
4.Closet door ventilation required: A minimum of 120 square inches (774.2 cm²) of opening, equally divided at the top and bottom of the door, is required. Openings should be located 3 inches (7.6 cm) from bottom and top of door. Openings are required to be unobstructed when a door is installed. A louvered door with equivalent air openings for the full length of the door is acceptable.
MIN INSTALLATION CLEARANCES - Inches (cm)
|
SIDES |
REAR |
TOP |
FRONT |
Alcove |
0” (0 cm) |
0” (0 cm)* |
0” (0 cm) |
n/a |
Under- |
0” (0 cm) |
0” (0 cm)* |
0” (0 cm) |
n/a |
Counter |
||||
Closet |
0” (0 cm) |
0” (0 cm)* |
0” (0 cm) |
1” (2.5 cm) |
*For other than straight back venting, a quick-turn 90° dryer vent elbow must be installed to achieve 0” (0 cm) installation.
0” (0 cm)
0” (0 cm)
3” (7.6cm)
60 sq. in. (387.1cm²)
60 sq. in. (387.1cm²)
3” (7.6cm)
closet door
1” |
0” |
(2.5 cm) |
(0 cm) |
NOTE
To achieve an installation with 0” (0 cm) clearance for the back of the dryer (for other than straight back venting), a quick-turn 90° dryer vent elbow must be installed as described previously in this manual.
Installation Requirements |
9 |
Dryer dimensions
53.5” (136 cm)* to clear open door
31.5” (79.5 cm)* |
27.0” |
|
to front of closed door |
(68.5 cm) |
|
38.0” |
electrical |
|
supply on |
||
(96.5 cm) |
||
rear of unit1 |
|
1.5” |
3.7” |
|
(4 cm) |
|
|
(9.5 cm) |
|
|
53.25” |
|
|
|
|
|
(135.5 cm) |
centerline |
freestand dryer |
gas supply |
height of |
on fl oor |
pipe on rear |
rear vent |
fl oor line |
of gas unit |
|
|
|
|
17.0” |
|
13.5” |
19.0” |
dryer mounted on |
(43 cm) |
|
(48 cm) |
|
|
|
(34.5 cm) |
|
|
optional pedestal |
|
|
|
|
|
3.75” |
to center of |
|
|
|
|
|
||
|
|
rear vent |
|
|
fl oor line |
|
(9.5 cm) |
|
|
|
|
|
53.5” (136 cm)* to clear open door
31.5” (79.5 cm)*
to front of closed door
75.75” (192.5 cm)
water supply connection on rear of unit
gas supply pipe on rear of gas unit
39.0” (99 cm)
electrical supply on rear of unit1
centerline height for rear vent
power cord on
drain hose on
rear of unit3
rear of unit2
41.0” (105 cm)
fl oor line
*Connection of water inlet hose on steam dryer adds 3/4 in. (2 cm) to installation depth.
1Power supply cord length on gas dryer or electric Canadian dryer approximately 60 inches (152.5 cm). 2Drain hose length on washer approximately 59 inches (150 cm).
3Power supply cord length on washer approximately 60 inches (152.5 cm).
10 |
Installation Instructions |
Electrical installation
The following are specifi c requirements for proper and safe electrical installation of your dryer. Failure to follow these instructions can create electrical shock and/or a fi re hazard.
WARNING
ELECTRICAL SHOCK HAZARD
●This appliance MUST be properly grounded. Electrical shock can result if the dryer is not properly grounded. Follow the instructions in this manual for proper grounding.
●Do not use an extension cord with this dryer. Some extension cords are not designed to withstand the amounts of electrical current this dryer utilizes and can melt, creating electrical shock and/or fi re hazard. Locate the dryer within reach of the receptacle for the length power cord to be purchased, allowing some slack in the cord. Refer to the pre-installation requirements in this manual for the proper power cord to be purchased.
WARNING
ELECTRICAL SHOCK HAZARD
●A U.L.-approved strain relief must be installed onto power cord. If the strain relief is not attached, the cord can be pulled out of the dryer and can be cut by any movement of the cord, resulting in electrical shock.
●Do not use an aluminum wired receptacle with a copper wired power cord and plug (or vice versa). A chemical reaction occurs between copper and aluminum and can cause electrical shorts. The proper wiring and receptacle is a copper wired power cord with a copper wired receptacle.
NOTE
Dryers operating on 208 volt power supply will have longer drying times than dryers operating on 240 volt power supply.
Grounding requirements - Electric dryer (USA)
WARNING
ELECTRICAL SHOCK HAZARD
Improper connection of the equipment grounding conductor can result in a risk of electrical shock. Check with a licensed
electrician if you are in doubt as to whether the appliance is properly grounded.
For a grounded, cord-connected dryer:
1.The dryer MUST be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electrical shock by providing a path of least resistance for electrical current.
2.After you purchase and install a 3 wire or 4 wire power supply cord having an equipmentgrounding conductor and a grounding plug that matches your wiring system, the plug MUST be plugged into an appropriate, copper wired receptacle that is properly installed and grounded in accordance with all local codes and ordinances. If in doubt, call a licensed electrician.
3.DO NOT modify the plug you’ve installed on this appliance. If it will not fi t the outlet, have a proper outlet installed by a qualifi ed electrician.
For a permanently connected dryer:
1.The dryer MUST be connected to a grounded metal, permanent wiring system; or an equipment grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the appliance.
Installation Instructions |
11 |
Grounding requirements - Electric dryer (Canada)
WARNING
ELECTRICAL SHOCK HAZARD
Improper connection of the equipment grounding conductor can result in a risk of electrical shock. Check with a licensed
electrician if you are in doubt as to whether the appliance is properly grounded.
For a grounded, cord-connected dryer:
1.The dryer MUST be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electrical shock by providing a path of least resistance for electrical current.
2.Since your dryer is equipped with a power supply cord having an equipment-grounding conductor and a grounding plug, the plug must be plugged into an appropriate outlet that is properly installed and grounded
in accordance with all local codes and ordinances. If in doubt, call a licensed electrician.
3.DO NOT modify the plug provided with this appliance. If it will not fi t the outlet, have a proper outlet installed by a qualifi ed electrician.
Grounding requirements - Gas dryer (USA and Canada)
Grounding type wall receptacle
Do not, under
any circumstances, cut, remove,
or bypass the grounding prong.
Power cord with 3-prong grounded plug
1.The dryer is equipped with a three-prong (grounding) plug for your protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle.
2.The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. If in doubt, call a licensed electrician.
3.DO NOT modify the plug provided with this appliance. If it will not fi t the outlet, have a proper outlet installed by a qualifi ed electrician.
12 |
Installation Instructions |
Electrical connection (non-Canada) - 3 wire cord
3-wire receptacle (NEMA type 10-30R)
WARNING |
30 AMP |
|
NEMA 10-30 |
ELECTRICAL SHOCK HAZARD
Failure to disconnect power source before servicing could result in personal injury or even death.
1. Turn o power supply to outlet.
2. Remove the screw securing the terminal block access cover in the lower corner on the back of the dryer.
3. Install a UL-approved strain relief according to the power cord/strain relief manufacturer’s instructions in the power cord entry hole below the access panel. At this time, the strain relief should be loosely in place.
4. Thread an UNPLUGGED, UL-approved, 30 amp. power cord, NEMA 10-30 type SRDT, through the strain relief.
5. Attach the power cord neutral (center wire) conductor to the SILVER colored center terminal on the terminal block. Tighten the screw securely.
Neutral (center wire)
Access cover screw
Terminal
block
Line 2 (BRASS terminal)
Neutral (SILVER terminal)
Line 1 (BRASS terminal)
Internal ground (GREEN screw)
Install
UL-approved strain relief here
Terminal screw recovery slot
6.Attach the remaining two power cord outer conductors to the outer, BRASS colored terminals on the terminal block. Tighten both screws securely.
NOTE
If a terminal screw falls during cord installation, it can be retrieved in the terminal screw recovery slot below the access panel.
WARNING
ELECTRICAL SHOCK HAZARD
Do not make a sharp bend or crimp wiring/ conductor at connections.
7.Follow manufacturer’s guidelines for fi rmly securing the strain relief and power cord.
8.Reinstall the terminal block cover.
IMPORTANT
If moving dryer from a 4-wire system and installing it in a 3-wire system, move the internal ground from the center terminal back to the GREEN screw next to the terminal block.
DO NOT remove internal ground in
Neutral
a 3-wire system!!
terminal
Installation Instructions |
13 |
Electrical connection (non-Canada) - 4 wire cord
4-wire receptacle (NEMA type 14-30R)
WARNING
ELECTRICAL SHOCK HAZARD
Failure to disconnect power source before servicing could result in personal injury or even death.
1.Turn o power supply to outlet.
2.Remove the screw securing the terminal block access cover in the lower corner on the back of the dryer.
3.Install a UL-approved strain relief according to the power cord/strain relief manufacturer’s instructions in the power cord entry hole below the access panel. At this time, the strain relief should be loosely in place.
4.Thread an UNPLUGGED, UL-approved, 30 amp. power cord, NEMA 14-30 type DRT or SRDT, through the strain relief.
5.Disconnect the internal (WHITE) dryer harness ground wire from the (GREEN) ground screw next to the terminal block.
6.Attach the ground (GREEN) power cord wire to the cabinet with the ground (GREEN) screw. Tighten the screw securely.
7.Move the internal dryer harness ground (WHITE) wire to the terminal block and attach it along with the neutral (WHITE) power cord wire conductor to the center, SILVER colored terminal on the terminal block. Tighten the screw securely.
8.Attach the RED and BLACK power cord conductors to the outer, BRASS colored terminals on the terminal block. Tighten both screws securely.
WARNING
ELECTRICAL SHOCK HAZARD
Do not make a sharp bend or crimp wiring/ conductor at connections.
9.Follow manufacturer’s guidelines for fi rmly securing the strain relief and power cord.
10.Reinstall the terminal block cover.
|
|
Neutral |
|
30 AMP |
Ground |
(WHITE wire) |
|
|
|||
(GREEN wire) |
|||
NEMA 14-30 |
|||
|
|
||
|
|
Access cover |
|
|
|
screw |
|
|
|
Terminal |
|
|
|
block |
|
|
|
Line 2 |
|
|
|
(BRASS terminal) |
|
|
|
Neutral |
|
|
|
(SILVER terminal) |
|
|
|
Line 1 |
|
|
|
(BRASS terminal) |
|
|
|
Internal ground |
|
|
|
(GREEN screw) |
|
|
|
Install |
|
|
|
UL-approved |
|
|
|
strain relief here |
|
|
|
Terminal screw |
|
|
|
recovery slot |
NOTE
If a terminal screw falls during cord installation, it can be retrieved in the terminal screw recovery slot below the access panel.
Move internal ground (WHITE) |
Neutral |
wire to neutral (SILVER) |
terminal |
terminal for 4-wire system. |
|
WHITE neutral wire
GREEN ground screw
GREEN |
BLACK |
ground wire |
or RED |
|
power wire |
BLACK or |
|
RED power wire |
|
14 |
Installation Instructions |
Gas connection
1.Remove the shipping cap from gas pipe at the rear of the dryer.
IMPORTANT
DO NOT connect the dryer to L.P. gas service without converting the gas valve. An L.P. conversion kit must be installed by a qualifi ed gas technician.
2.Connect a 1/2 inch (1.27 cm) I.D. semi-rigid or approved pipe from gas supply line to the 3/8 inch (0.96 cm) pipe located on the back of the dryer. Use a 1/2 inch to 3/8 inch (1.27 cm to 0.96 cm) reducer for the connection. Apply an approved thread sealer that is resistant to the corrosive action of liquefi ed gases on all pipe connections.
3.Open the shuto valve in the gas supply line to allow gas to fl ow through the pipe. Wait a few minutes for gas to move through the gas line.
to dryer
from |
gas |
supply |
|
||
|
|
Shutoff Valve -
Open position
Manual |
Flare |
GAS FLOW |
Flare |
Shutoff |
|
||
Union |
|
Union |
|
Valve |
|
||
|
|
|
|
Closed |
|
|
|
Nipple |
Flexible |
Inlet Pipe on |
|
Open |
|
Connector |
Back of Dryer |
All connections must be wrench-tightened
4.Check for gas system leaks with a manometer. If a manometer is not available, test all connections by brushing on a soapy water solution.
WARNING
EXPLOSION HAZARD
NEVER test for gas leaks with an open fl ame.
IMPORTANT
Installation to the gas service must follow local codes and ordinances and the latest edition of the National Fuel Gas Code ANSI Z223.1/NEPA 54 or in Canada, CSA B149.1.
Installation Instructions |
15 |
Water connection (Steam Model only)
WATER SUPPLY REQUIREMENTS
Cold water faucet MUST be installed within 42 inches (107 cm) of your dryer’s water inlet. The faucet MUST be 3/4 inch (1.9 cm) with threading for laundry hose connection. Water pressure MUST be between 30 and 120 psi. Your water department can advise you of your water pressure.
1. Turn o COLD water supply to washer,
2.Remove COLD inlet hose from COLD water supply and inspect for rubber washer. Replace washer if it is torn or worn out.
RUBBER WASHER
MUST BE PRESENT
AND UNDAMAGED
COLD INLET HOSE
TO WASHER
3. Momentarily turn on COLD supply and run some water into a bucket or container to clear any contaminants in the line.
4. Remove hose kit from dryer drum and inspect hose couplings for proper placement of rubber washers.
RUBBER WASHERS
MUST BE PRESENT
16 |
Installation Instructions |
|
Water connection, continued (Steam Model only) |
5.If your installation has room for the COLD water supply to accept the “Y” connector directly, thread the “Y” connector to the COLD water supply and snug it by hand; then tighten it another 2/3 turn with pliers.
NOTE
If you were able to install the “Y” connector directly to the COLD water supply, please skip to step 8.
6.If there is not room to install the “Y” connector directly, thread the short extension hose on to the COLD water supply and snug it by hand; then tighten it another 2/3 turn with pliers.
7.Thread the “Y” connector to the short extension hose and snug it by hand; then tighten it another 2/3 turn with pliers.
8.Connect the COLD inlet hose for the washer to the “Y” connector and snug it by hand; then tighten it another 2/3 turn with pliers.
9.Connect the straight end of the long hose from the kit to the other outlet on the “Y” connector and snug it by hand. Connect the hose’s 90° coupling to the brass water inlet on the back of the dryer and snug it by hand. Tighten each connection of the dryer inlet hose another 2/3 turn with pliers.
10.Turn on the water and check for leaks at all connections.
DIRECT CONNECTION
OR WITH EXTENSION
WATER INLET
ON DRYER
COLD WATER SUPPLY
HOSE TO WASHER
Installation Instructions |
17 |
General installation
1. Connect the exhaust duct to the outside exhaust system. Use of a 4” (102 mm) clamp (item A) is recommended to connect the dryer to the exhaust vent system. Use metal foil tape to seal all other joints.
2. Use a carpenter’s level to level your dryer front-to-back and side-to-side.
3. Use adjustable pliers to adjust the leveling legs so the dryer is level front-to-rear and side-to-side, and stable corner-to-corner.
4. Press down on alternate corners and sides |
|
and feel for the slightest movement. Adjust |
|
the appropriate leg(s) so the dryer sits |
|
solidly on the fl oor on ALL four legs. Keep |
|
the leveling leg extension at a minimum for |
|
best performance of the dryer. |
A |
IMPORTANT
Be sure the power is o at a circuit breaker/ fuse box before plugging the power cord into an outlet.
5. Plug the power cord into a grounded outlet.
Grounding type wall receptacle
Do not, under
any circumstances, cut, remove,
or bypass the grounding prong.
Power cord with 3-prong grounded plu
6.Turn on the power at the circuit breaker/fuse box.
7.Read the Use & Care Guide provided with the dryer. It contains valuable and helpful information that will save you time and money.
8.If you have any questions during initial operation, please review the “Avoid Service Checklist” in your Use & Care Guide before calling for service.
9.Place these instructions in a location near the dryer for future reference.
NOTE
A wiring diagram and technical data sheet are located under the dryer top panel.
CAUTION
When discarding or storing your old dryer, remove the door.
18 Reversing Door
IMPORTANT
BEFORE YOU REVERSE YOUR DRYER DOOR:
1.Be sure you have adequate swing area before reversing door.
2.Gather your tools - including a screw driver with a #2 square bit and plastic knife (or small, fl at prying tool that won’t damage paint).
3.Be sure dryer is unplugged from power source!
WARNING
ELECTRICAL SHOCK HAZARD
Failure to disconnect power source before servicing could result in personal injury or even death.
A)Removing Latch Cover and Hole Plugs
1.Open the door.
2.Remove plastic hole plugs and save to reinstall later. You may have to use a nanscratching plastic knife if you are unable to dislodge the plugs manually.
Tools needed for reversal:
Screwdriver with #2 square bit
Plastic knife
B)Removing Door Assembly
1.Completely open the door to expose all four hinge screws.
2.Remove all four hinge screws with #2 square bit driver. Save for reinstalling later.
x4
x2
3.Remove both screws from door latch cover. Save cover and screws for reinstallation later.
3.Grasp the door with both hands and lift slightly as you pull door and hinge away from the front panel.
x2
|
Reversing Door 19 |
C) Reinstalling Door Assembly |
D) Reinstalling Latch Cover and Hole Plugs |
1.Rotate the door and hang the hook upper hook on the back of the hinge in the upper hole of the front panel.
1.Install door latch cover with screws removed earlier.
2.Reinstall and tighten all four screws removed earlier.
x4
x2
2. Insert plastic hole plugs removed earlier.
x2
E)Verify Reversed Door Operation
1.Test door for free, smooth swinging operation and secure latching when closed.
2.Plug in dryer and close the door. Start a test cycle: drum should tumble until
door is pulled open or cycle is paused or canceled.
20 Options
Accessories
MATCHING STORAGE PEDESTAL*
White Pedestal - P/N EPWD157SIW
Titanium Pedestal - P/N EPWD157STT
A storage pedestal accessory, specifi cally designed for this dryer may be used to elevate the dryer for ease of use. This pedestal will add
about 15” (38 cm) to the height of your unit.
*Other colors may be available. Contact the source where you purchased your dryer.
DRYER STACKING KIT
P/N STACKIT7X
Depending on the model you purchased, a kit for stacking a matching dryer on top of this washer may have been included in the initial purchase of your dryer. If your model did not include a stacking kit or you desire another stacking kit, you may order one.
LP CONVERSION KIT
P/N 134709300
Gas dryers intended for use in a location supplied with LP must use a conversion kit prior to installation.
MOBILE HOME INSTALLATION KIT
P/N 137067200
Installations in mobile homes require use of MOBILE HOME INSTALLATION KIT.
DRYING RACK
P/N A04840701
Depending on the model you purchased, a drying rack may have been included in the initial purchase of your dryer. If your model did not include a drying rack or you desire another drying rack, you may order one.
UNIVERSAL APPLIANCE WRENCH
P/N 137019200
A UNIVERSAL APPLIANCE WRENCH is available to aid in dryer/washer/pedestal feet adjustment.
TOUCH UP PAINT PENS
White - P/N 5304468812 Titanium - P/N 5304475700
*Other colors may be available. Contact the source where you purchased your dryer.
CAUTION
Failure to use accessories manufactured by (or approved by) the manufacturer could result in personal injury, property damage or damage to the dryer.
( |
27” |
|
|
|
|
68. |
|
|
|
5c |
|
|
|
m) |
15” (38 cm)
26.5” |
) |
|
(67 cm |
||
|
Replacement parts in U.S. and Canada:
If replacements parts are needed for your dryer, you can contact the source where you purchased your dryer, call 1-877-4ELECTROLUX (1-877-435-3287) in the U.S. or 1-800-265-8352 in Canada, or visit our website, www. electroluxappliances.com, for the Electrolux Authorized Parts Distributor nearest you.
WARNING
ELECTRICAL HAZARD
Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.