Electro-Harmonix Crying Tone Instruction Manual
CRYING TONE
WAH PEDAL
Congratulations on your purchase of the Electro-Harmonix Crying Tone, our first
release in our ground-breaking NEXT STEP series! The Crying Tone is a wah pedal
without any moving parts: it does not use a potentiometer, optics or magnetics to
sweep the wah filter. The result is a responsive pedal that allows precise control over
a brilliantly fluid wah.
GETTING STARTED
Plug your guitar into the INPUT jack; connect your amp to the OUTPUT jack. Within
seconds the EHX logo in the center of the pedal will light. Your Crying Tone is ready
to go! Please note: as long as a plug is inserted into the INPUT jack, a drain is placed
on the 9V battery inside the Crying Tone. It is recommended that you disconnect the
INPUT jack when the Crying Tone is not in use to extend battery life.
CALIBRATION
To ensure the Crying Tone responds to its full sweep range, it may be necessary to
calibrate the sweep of the Crying Tone when it is used on a different surface since its
last use. It is particularly important to calibrate if the Crying Tone is used on a
slanted surface. We recommend calibrating the Crying Tone after unwrapping it from
its packaging, during your first use of the pedal.
CALIBRATION PROCEDURE
1. Place the pedal on the surface where it will be used.
2. Ensure the Crying Tone is sitting flat on the surface then press and release
the CALIBRATION button once; the EHX logo begins to blink indicating the
toe position has been saved.
3. While the EHX logo continues to blink, rock the pedal all the way back to the
extreme heel position and hold it there.
4. Press and release the CALIBRATION button once more.
5. The EHX logo stops blinking to indicate that the heel position has been
saved.
If you accidentally press the CALIBRATION button and the EHX logo blinks, do not
press the CALIBRATION again. After approximately 7 seconds, the Crying Tone will
stop blinking and ignore the button press.
ENTERING/EXITING BYPASS
Toggle between buffered bypass and effect mode by tipping the Crying Tone
forward, in the toe direction, past the flat position of the Crying Tone. You do not
need to tip the Crying Tone all the way forward; 25% of the total forward travel will
do it. The Crying Tone needs to return to its flat position before you can toggle
between bypass and effect mode again.
When the Crying Tone is in effect mode, the EHX logo in the center of the pedal will
light up. In bypass mode, the logo does not light.
POWER
Plugging into the INPUT jack activates power from the internal 9 Volt battery. The
input cable should be removed when the unit is not in use to avoid running down the
battery. If an AC Adapter is used, the Crying Tone will be powered up as long as the
AC Adapter is correctly plugged in.
The Crying Tone’s power jack is located on the same side as the OUTPUT jack. A 9
Volt AC Adapter capable of delivering at least 25 mA of current is required to power
the Crying Tone. The inner ring of the 9 Volt AC Adapter must be negative, the outer
ring positive. The optional 9V power supply from Electro-Harmonix is 9.6DC-200BI
(same as used by Boss™ & Ibanez™) 9.6 Volts DC/200mA. The unit’s battery may be
left in or taken out when the AC Adapter is in use. The actual current draw of the
Crying Tone is 11 mA.
CHANGING THE BATTERY
1. Locate the battery door at the front of the Crying Tone, under the toe area
of the top plate.
2. Remove the large black screw that holds the battery door to the case, most
coins or larger slotted screwdrivers can be used to remove this screw.
3. Connect your new 9V battery to the wired battery connector.
4. Insert the 9V battery into the battery holder clip on the battery door so that
the wired connector is on the same side of the hole in the battery door.
5. Place the battery door back into its window in the case of the Crying Tone
and re-install the screw.
NOTES AND SPECIFICATIONS
Crying Tone’s bypass is buffered.
The input impedance presented at the INPUT Jack is 1M. The output
impedance at the OUTPUT Jack is 1k.
The current draw of the Crying Tone is 11 mA.
- WARRANTY INFORMATION -
Please complete and return the enclosed warranty card within 10 days of purchase.
Electro-Harmonix will repair or replace, at its discretion, a product that fails to
operate due to defects in materials or workmanship for a period of one year from
date of purchase. This applies only to original purchasers who have bought their
product from an authorized Electro-Harmonix retailer. Repaired or replaced units will
then be warranted for the unexpired portion of the original warranty term.If you
should need to return your unit for service within the warranty period, please include
a brief description of the problem as well as your name, address, telephone number,
copy of your receipt, and a check or money order. The costs for shipping and
handling are listed below.
United States - $12
Canada - $15
Europe and other countries - $25
Ship to:
Electro-Harmonix
C/O New Sensor Corporation
55-01 2nd Street
Long Island City, NY 11101
Attn: Service Department
Please make checks/money orders payable to New Sensor Corporation.
To hear demos on all EH pedals visit us on the web at www.ehx.com.
Email us at info@ehx.com
Note:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Modifications not expressly approved by the manufacturer could void the user's authority to
operated the equipment under FCC rules.
Consult the dealer or an experienced radio/TV technician for help.
- FCC COMPLIANCE -
Loading...