Electro Harmonix Andy Summers Walking on the Moon Analog Flanger / Filter Matrix effectpedaal EHX Andy Summers Walking on the Moon manual

Congratulations on your purchase of the Andy Summers Walking
On The Moon Flanger/Filter Matrix! Over the past six decades,
Andy Summers has relied on anger effects to dene his signature

sound palate, enabling him to create the lush and shimmering

guitar tones that made Andy Summers famous all over the world

and especially beloved by guitar players.

Operating Instructions

Connect your guitar to the INPUT jack of the Walking On The Moon (WOTM)
and the FLANGED OUT jack to your amp’s input. Plug in the included power
supply and insert its output plug into the WOTM’s power jack. Press the
footswitch to ensure the red LED is lit, the WOTM is now ready to play.

To get started, try the following setting:

COLOR: 12 o’clock RANGE: 9 o’clock RATE: 9 o’clock

POWER SUPPY REQUIREMENTS:

Voltage: 9VDC Current: 40mA Polarity: Center-Negative

This device comes equipped with an Electro-Harmonix 9.6DC-200 power supply. It requires 40mA at 9VDC

with a center negative plug. Use of the wrong adapter or a plug with the wrong polarity may damage the

device and void the warranty. Do not exceed 10.5VDC on the power plug. Power supplies rated for less
than 50mA will cause the device to act unreliably. The Walking On The Moon also accepts 9V batteries,

we recommend alkaline.

Controls and Connections

1. COLOR Knob sets the intensity of the anger effect. As you turn COLOR

clockwise, the effect becomes more pronounced, producing that classic

whoosh effect angers are famous for.
Your WOTM has been set at the factory for maximum color capacity.

Turning COLOR up to maximum could cause self-oscillation to occur.

This is normal! The oscillation may be reduced by turning down the

COLOR knob one or two notches.

2. RANGE Knob allows you to set the lower limit of the anger sweep.
A fully counterclockwise setting, where the lower limit is just below the
higher limit, creates a narrow sweep effect. As you turn RANGE clock­wise the anger sweeps down further into the bass region.

- 2 -

3. RATE Knob controls the speed of anger modulation. As you turn
RATE clockwise, the anger’s speed increases. Higher settings of RATE

give the effect a sound like vibrato.

4. FILTER MATRIX Switch when this switch is set to the right position,

labeled FILTER MATRIX, the modulation waveform is disconnected from
the anger circuit, freezing the anger and creating a matrix of lters.
Turn the RANGE knob to change the lters’ position and use COLOR to
adjust the depth of ltering. The RATE knob has no effect when set to
FILTER MATRIX mode. Proper manipulation of the RANGE and COLOR

knobs will enable you to simulate the sound of chimes being played in
unison with your instrument, as well as many other effects.

5. FOOTSWITCH and STATUS LED Use the footswitch to switch between

bypass and effect mode. The LED is off when WOTM is in true bypass
mode. When WOTM is active, the LED is lit.

6. INPUT Jack Audio input to WOTM.

7. FLANGED OUT Jack Main audio output from WOTM. All anging and

modulation effects will emanate from this jack.

8. DRY OUT Jack Secondary audio output from WOTM. DRY OUT is di-
rectly connected to the INPUT jack in all modes.

9. 9V Power Jack Attach the output plug from the included power supply
to the 9V power jack. WOTM draws 40mA at 9VDC on a center-negative
plug. Do not exceed 10.5VDC on the power jack.

To power WOTM from a 9V battery, you must remove the 4 screws holding
the bottom plate. Once the screws are removed, detach the bottom plate
and connect a 9V battery. Please do not touch the circuit board while the
bottom plate is off or you risk damaging a component.

Notes and Specications

t Audio input impedance at INPUT jack: 600kΩ
t Audio output impedance at FLANGED OUT jack: 5.5kΩ
t Current draw: 40mA at 9.0VDC
t Maximum Input Signal (before clipping): 0 dBu
t Maximum Output Signal: +4 dB

- 3 -

WARRANTY INFORMATION

Please register online at www.ehx.com/product-registration or complete and re-
turn the enclosed warranty card within 10 days of purchase. Electro-Harmonix will
repair or replace, at its discretion, a product that fails to operate due to defects
in materials or workmanship for a period of one year from date of purchase. This
applies only to original purchasers who have bought their product from an autho­rized Electro-Harmonix retailer. Repaired or replaced units will then be warranted
for the unexpired portion of the original warranty term.

If you should need to return your unit for service within the warranty period, please

contact the appropriate ofce listed below. Customers outside the regions listed
below, please contact EHX Customer Service for information on warranty repairs
at [e-mail] or [phone]. USA and Canadian customers: please obtain

a Return Authorization Number (RA#) from EHX Customer Service before returning
your product. With your returned unit, include a written description of the problem

as well as your name, address, telephone number, e-mail address, RA# and a copy

of your receipt clearly showing the purchase date.

United States & Canada

EHX Customer Service
Electro-Harmonix

co New Sensor Corp.
47-50 33rd Street
Long Island City, NY 11101

Tel: [phone]
Email: [e-mail]

This warranty gives a purchaser specic legal rights. A purchaser may have even greater rights depending upon

the laws of the jurisdiction within which the product was purchased.

Europe

John Williams
Electro-Harmonix UK

13 Cwmdonkin Terrace
Swansea SA2 0RQ

United Kingdom

Tel: [phone]
Email: [e-mail]

COMPLIANCE

Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Modications not expressly approved by the manufacturer could void the user’s authority to oper­ate the equipment under FCC rules.

The CE logo indicates that this product has been tested and shown to conform with all applicable
European Conformity directives.

The WEEE or “trashcan” logo indicates that this product is made up of electronic components that should not
be trashed alongside household waste but instead should be recycled by a proper electrical waste facility.