Elecraft KAT3 User Manual
®
ELECRAFT
HIGH-PERFORMANCE 160 – 6 METER
T
RANSCEIVER
KAT3 100-WATT
UTOMATIC ANTENNA TUNER
A
NSTALLATION INSTRUCTIONS
I
Rev C, June 24, 2008
Copyright © 2008, Elecraft, Inc.
K3
All Rights Reserved
Contents
Introduction............................................................................................................................................... 3
Customer Service and Support............................................................................................................................ 3
Technical Assistance....................................................................................................................................... 3
Repair / Alignment Service............................................................................................................................. 3
Preventing Electrostatic Discharge Damage ............................................................................................ 4
How ESD Damage Occurs.................................................................................................................................. 4
Preventing ESD Damage..................................................................................................................................... 4
Preparing for Installation .......................................................................................................................... 5
Tools Required.................................................................................................................................................... 5
Parts Included...................................................................................................................................................... 5
Installation Procedure ............................................................................................................................... 6
Removing the Top Cover .................................................................................................................................... 6
Removing the KRX3 Subreceiver Module ......................................................................................................... 6
Removing the Right Side Panel .......................................................................................................................... 8
Removing the KANT Module............................................................................................................................. 9
Installing the ANT2 Connector......................................................................................................................... 10
Installing the KAT3 Module ............................................................................................................................. 10
Reinstalling the KRX3 Subreceiver Module..................................................................................................... 11
Replacing the Top Cover .................................................................................................................................. 12
Enabling the KAT3................................................................................................................................. 12
2
Introduction
The KAT3 option is an internally-mounted 100-watt automatic antenna tuner. Complete details for using the
KAT3 are included in the K3 Owner’s manual. This manual covers the installation of the KAT3 option in your
K3 transceiver.
Only a few basic hand tools are needed (see page 5) to perform the installation. No soldering or wiring is
required.
Customer Service and Support
Technical Assistance
You can send e-mail to support@elecraft.com and we will respond quickly - typically the same day Monday
through Friday. Telephone assistance is available from 9 A.M. to 5 P.M. Pacific time (weekdays only) at 831662-8345. Please use e-mail rather than calling when possible since this gives us a written record of the details
of your problem and allows us to handle a larger number of requests each day
.
Repair / Alignment Service
If necessary, you may return your Elecraft product to us for repair or alignment. (Note: We offer unlimited email
and phone support to get your kit running, so please try that route first as we can usually help you find the
problem quickly.)
IMPORTANT: You must contact Elecraft before mailing your product to obtain authorization for the
return, what address to ship it to and current information on repair fees and turn around times. (Frequently we
can determine the cause of your problem and save you the trouble of shipping it back to us.) Our repair location
is different from our factory location in Aptos. We will give you the address to ship your kit to at the time of
repair authorization. Packages shipped to Aptos without authorization will incur an additional shipping charge
for reshipment from Aptos to our repair depot
(We want to make sure everyone succeeds!)
.
Elecraft 1-Year Limited Warranty
This warranty is effective as of the date of first consumer purchase. It covers both our kits and fully assembled
products. For kits, before requesting warranty service, you should fully complete the assembly, carefully following all
instructions in the manual.
What is covered: During the first year after date of purchase (or if shipped from factory, date product is shipped to
customer), Elecraft will replace defective or missing parts free of charge (post-paid). We will also correct any
malfunction to kits or assembled units caused by defective parts and materials. Purchaser pays inbound shipping to us
for warranty repair, we pay shipping to return the repaired equipment to you by UPS ground service or equivalent to
the continental USA and Canada. Alaska, Hawaii and outside U.S. and Canada actual return shipping cost paid by
owner.
What is not covered: This warranty does not cover correction of kit assembly errors. It also does not cover
misalignment; repair of damage caused by misuse, negligence, or builder modifications; or any performance
malfunctions involving non-Elecraft accessory equipment. The use of acid-core solder, water-soluble flux solder, or
any corrosive or conductive flux or solvent will void this warranty in its entirety. Also not covered is reimbursement
for loss of use, inconvenience, customer assembly or alignment time, or cost of unauthorized service.
Limitation of incidental or consequential damages: This warranty does not extend to non-Elecraft equipment or
components used in conjunction with our products. Any such repair or replacement is the responsibility of the
customer. Elecraft will not be liable for any special, indirect, incidental or consequential damages, including but not
limited to any loss of business or profits.
3
Preventing Electrostatic Discharge Damage
There is no climate or work location where the components of your K3 are safe from Electrostatic Discharge
(ESD) unless you take specific steps to prevent such damage. Many of the components in your K3 can be
damaged by static discharges of only a few volts: far too little for you to notice. It is those low-voltage but
destructive discharges that easily happen anywhere and under virtually any environmental conditions.
ESD damage may not be apparent at first. The damaged components may not fail completely. Instead, the
damage may result in below-normal performance for an extended period of time before you experience a total
failure.
How ESD Damage Occurs
Whenever an object containing a static charge touches a circuit in your K3, current will rush into the circuit until
the components reach the same voltage as the source of the static charge. If the voltage or current that passes
through a component during that brief period exceeds its normal operating specifications, it may be damaged or
destroyed.
Preventing ESD Damage
ESD damage cannot occur if there is no voltage difference between the components in your K3 and any object
that touches them. That is how anti-static packaging works. Anti-static bags allow the static charge to flow over
their surface, so that any part of the bag that touches the components inside are all at the same potential at all
times. Anti-static foam keeps the leads of sensitive components at the same potential.
At your work bench, avoiding a dangerous voltage is achieved most easily by tying everything together and
connecting them to a common mains safety ground. This includes your K3, individual boards or other sensitive
components as well as everything they may touch at the work table.
Inexpensive static dissipating work mats are readily-available that will steadily and safely drain off any charges
built up on parts or circuit boards placed on them. They are supplied with a lead that connects the mat to the
common workbench ground. Also, metal cabinets on test equipment used on the bench should be tied together
and connected to the common ground.
Most importantly, you must have a way of continuously draining off any static charges that occur on your body.
Such charges are easy to create, even while sitting quietly at the work bench. Moving your feet on the floor,
shifting position in your chair or even moving your arms so that clothing rubs against itself can produce
destructive static charges. You can discharge yourself by touching an unpainted metal ground, but that will last
only until you move in a way that produces a new static charge. The safest technique is to wear a grounded wrist
strap with a series 1-megohm resistor that continuously drains off any charges. Such wrist straps are readilyavailable and inexpensive.
WARNING
DO NOT attach a ground directly to yourself without a current-limiting resistor as this poses
a serious shock hazard. A wrist strap must include a 1-megohm resistor to limit the current
flow. If you choose to touch an unpainted, metal ground to discharge yourself, do it only
when you are not touching any live circuits with your other hand or any part of your body.
We strongly recommend you take the following anti-static precautions (listed in order of importance) to avoid
trouble:
• Leave ESD-sensitive parts in their anti-static packaging until you install them. The packaging may be a
special plastic bag or the component’s leads may be inserted in conductive foam. Parts which are
especially ESD-sensitive are identified in the parts list and in the assembly procedures.
4
Loading...