Elation Professional Design LED 36 Pro User Manual

Rev. 12/10/2008 - visage

Design LED 36 Pro

Elation Professional™

6122 S. Eastern Ave.

Los Angeles, Ca 90040

www.elationlighting.com

DESIGN LED 36 Pro™

©Elation Professional, Los Angeles Ca. 1 www.ElationLighting.com

DESIGN LED 36 Pro™

©Elation Professional, Los Angeles Ca. 2 www.ElationLighting.com

TABLE OF CONTENS

1. General Information……………………………………………………………………… 3

a. Introduction………………………………………………………………………. 3

b. Unpacking………………………………………………………..…………..….. 3

c. Customer Support…………………………………………….………………… 3

d. Warranty Registration…………………………………………………………… 4

2. Safety Instructions………………………………………………………........…………. 5

3. Features…………………………………………………………………………………… 7

4. General Guidelines………………………………………………………………………. 8

5. Fixture Overview…………………………………………………………………………. 9

6. Mounting and Installation………………………………………………………….……. 11

a. Yoke Assembly………………………………………………………………….. 11

b. Mounting Positions……………………………………………………………… 12

c. Mounting Points…………………………………………………………………. 12

d. Clamp Mounting…………………………………………………………………. 12

e. Securing………………………………………………………………………….. 13

7. Understanding DMX……………………………………………………………………... 14

a. DMX Connections………………………………………………………………. 15

b. DMX Terminator…………………………………………………………………. 15

c. 3-Pin to 5-Pin Conversion………………………………………………………. 16

d. Fixture DMX Addressing.……………………………..………………………… 16

8. Display LED Indicators..…………………………………………………………………. 18

9. Display Menu..………………………………………………………………………….… 19

10. DMX Traits………………………………………………………………………………… 21

a. 3-Channel Mode………………………………………………………………… 21

b. 4-Channel Mode…..…………………………………………………………..… 22

c. 6-Channel Mode…..……………………………………………..……………… 23

11. Lens Replacement……… ……………………………………………………………… 25

12. Cleaning and Maintenance……………………………………………………………… 26

13. Warranty…………………………………………………………………………………... 27

14. Photometric Data………………………………………………………………………… 29

15. Dimensional Drawings………………………………………………….……………….. 32

16. Circuit Schematic………...………………………………………………………………. 33

17. Technical Specifications…………………………………………...………….………… 34

DESIGN LED 36 Pro™

©Elation Professional, Los Angeles Ca. 3 www.ElationLighting.com

1. GENERAL INFORMATION

INTRODUCTION: Congratulations, you have just purchased one of the most innovative and

reliable LED fixtures on the market today! The Design LED 36 Pro™ has been designed to

perform reliably for years when the guidelines in this booklet are followed. Please read and

understand the instructions in this manual carefully and thoroughly before attempting to

operate this unit. These instructions contain important information regarding safety during

use and maintenance.

UNPACKING: Thank you for purchasing the Design LED 36 Pro™ by Elation Professional®.

Every Design LED 36 Pro™ has been thoroughly tested and has been shipped in perfect

operating condition. Carefully check the shipping carton for damage that may have occurred

during shipping. If the carton appears to be damaged, carefully inspect your fixture for

damage and be sure all accessories necessary to operate the fixture have arrived intact. In

the event damage has been found or parts are missing, please contact our customer support

team for further instructions. Inside the box you should find: the fixture, a DMX XLR cable, a

safety cable, and this manual. Please do not return this unit to your dealer without first

contacting customer support at the number listed below.

CUSTOMER SUPPORT: Elation Professional® provides a customer support line, to provide

set up help and to answer any question should you encounter problems during your set up

or initial operation. You may also visit us on the web at www.elationlighting.com for any

comments or suggestions. For service related issue please contact Elation Professional®.

Service Hours are Monday through Friday 9:00 a.m. to 5:00 p.m. Pacific Standard Time.

Voice: [phone]

Fax: [phone]

E-mail: [e-mail]

Forum: www.ElationLighting.com/forum

Warning! To prevent the risk of fire and reduce the risk electrical shock do not attempt to

operate this fixture with the lens cover removed.

Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs

DESIGN LED 36 Pro™

©Elation Professional, Los Angeles Ca. 4 www.ElationLighting.com

yourself. Doing so will void your manufactures warranty.

Please do not discard the shipping carton in the trash. Please recycle whenever possible.

WARRANTY REGISTRATION: The Design LED 36 Pro™ carries a two year (730 days)

limited warranty. Please fill out the enclosed warranty card to validate your purchase. All

returned service items whether under warranty or not, must be freight pre-paid and

accompany a return authorization (R.A.) number. The R.A. number must be clearly written

on the outside of the return package. A brief description of the problem as well as the R.A.

number must also be written down on a piece of paper and included in the shipping

container. If the unit is under warranty, you must provide a copy of your proof of purchase

invoice. Items returned without a R.A. number clearly marked on the outside of the package

will be refused and returned at customer’s expense. You may obtain a R.A. number by

contacting customer support at [phone].

DESIGN LED 36 Pro™

©Elation Professional, Los Angeles Ca. 5 www.ElationLighting.com

2. SAFETY INSTRUCTIONS

To guarantee proper and consistent operation, it is important to
follow the guidelines in this manual. Elation Professional will not
accept responsibility for damages resulting from the misuse of
this fixture due to the disregard of the information printed in this
manual.

1. To reduce the risk of fire or shock, do not expose this fixture to rain or moisture.

Although this fixture shares a case design with our outdoor rated DLED 108IP,

this version has not been approved for outdoor use. Use of this fixture outdoors

will void all manufactures warranty.

2. Always be sure that the fan and the air inlets remain clean and are never

blocked. Allow about 6” (15cm) between this fixture and other devices or a wall

to allow for proper cooling.

3. Never touch the fixture during normal operation.

4. Never look directly into the light source. You risk injury to your retina, which may

induce blindness.

5. For safe operation, follow the Installation guide described in chapter six of this

manual. Operating the Design LED 36 Pro™ without suited safety aids such as

safety cables or clamps can increase the risk of damage and/or personal injury.

6. Qualified and certified personnel should only perform installation.

7. When mounting this fixture, use only the original rigging points included with this

fixture. Any structural modification will void the original manufactures warranty

and may increase the risk of damage and/or personal injury.

8. Do not attempt to operate this fixture if the power cord has become damaged or

frayed.

9. Never open this fixture while in use.

10. This device falls under protection-class I. Therefore it is essential that the device

be grounded properly.

DESIGN LED 36 Pro™

©Elation Professional, Los Angeles Ca. 6 www.ElationLighting.com

11. Qualified personnel should perform all electrical connections.

12. Be sure the available voltage matches the voltage requirements of the unit. Be

sure the power cord is never crimped or damaged. If the power cord is damaged,

replace it immediately with a new one of similar power rating.

13. Always disconnect from main power before performing any type of service or

any cleaning procedure.

14. Only handle the power cord by the plug. Never pull out the plug by tugging the

wire portion of the cord.

15. Please be aware that damages caused by modifications to the device are

not subject to warranty.

Important Notice: Damages resulting from the disregard of safety and general user

instructions found in this user manual are not subject to any warranty claims.

DESIGN LED 36 Pro™

©Elation Professional, Los Angeles Ca. 7 www.ElationLighting.com

3. FEATURES

• Low power consumption

• Minimal heat emission

• Maintenance free operation

• Equipped with 36 3-Watt (12 x red, 12 x green, 12 x blue)

• Silent Operation, convection cooled, no fans

• 100,000 hours rated LED life

• Linear RGB Color Mixing, infinite color possibilities

• 47˚ Standard Beam Angle (15˚ Lens - Optional 25˚ & 45˚ Lens Kits Available)

• USITT DMX-512 Complaint

• Preprogrammed colored macros

• Strobe-effect with a maximum flash rate of 18fps

• DMX-controlled operation or stand-alone operation with Master/Slave-function

• 8 built-in programs can be called up via DMX-controller

~ 48 preprogrammed scenes per program

• Sound-controlled via built-in microphone

• Three DMX Modes:

6 DMX channels

4 DMX channels

3 DMX channels

• DMX-control via standard DMX-controller

• Power Switching Electronic Power Supply 100v~240v

• Flicker-free operation for television and film

• Compact design: fits in 12” box truss

• 0%~100% Dimming (two dimming options; linear & standard)

DESIGN LED 36 Pro™

©Elation Professional, Los Angeles Ca. 8 www.ElationLighting.com

4. GENERAL GUIDELINES

This fixture is a professional lighting effect designed for use on stage, in nightclubs, in

theatres, and other types of architectural installations. Do not attempt operation or

installation without a proper knowledge on how to do so.

This fixture was designed for indoor use only; use of this fixture outside will void the

manufacture’s warranty.

Consistent operational breaks will ensure that the fixture will function properly for many

years to come.

Do not shake the fixture around. Avoid brute force when installing or operating the fixture.

While choosing an installation location, please be sure that the fixture will not be exposed to

extreme heat, moisture, or dust. The minimum distance between the fixture and a wall or flat

surface should be at least 0.5 meter (about 1.5ft). See page 11.

Always install the fixture with an appropriately rated safety cable. When installing the fixture

in a suspended environment always be sure to use mounting hardware no less than M10 x

25 mm, also be sure the hardware is only inserted in the yoke’s mounting holes.

Do not attempt to operate this fixture until you have familiarized yourself with all of its

functions.

Do not permit operation by persons not qualified for operating this type of architectural

fixture. Most damages are the result of improper operation.

Please use the original packaging to transport the fixture in for service.

For your own safety, please read this user manual carefully before installing the device.

DESIGN LED 36 Pro™

©Elation Professional, Los Angeles Ca. 9 www.ElationLighting.com

5. FIXTURE OVERVIEW

1. LED Lens Assembly – The lens assembly may be user replaced in the event repair

is needed or a different beam angle is required.

DESIGN LED 36 Pro™

©Elation Professional, Los Angeles Ca. 10 www.ElationLighting.com

2. LED Display – 4-segment menu display. Used to display the DMX address as well

as all other menu functions.

3. Power Output Lead – This lead is used to jump power to another Design LED 36

Pro™. Please do not daisy-chain power for more than 16 fixtures.

4. DMX Out Lead – XLR female lead. This lead is used to send an incoming DMX

signal to the next fixture in the DMX chain.

5. Menu Button – This button is used to access the fixtures menu functions.

6. Up Button – The up button is used to toggle forward through the menu functions and

settings.

7. Down Button – The down button is used to toggle backwards through the menu

functions and settings.

8. Enter Button – The enter button is used to enter in to a certain menu function or to

lock a menu setting in to memory.

9. Yoke Assembly – This yoke is designed to perform two functions; 1) When split it

can be used as a floor stand bracket. 2) Used to secure a mounting clamp for truss

mounting.

10. Main Power Input Lead – This lead is the main power input lead.

11. DMX In Lead – XLR male lead. This lead is the main DMX input lead.

6. MOUNTING AND INSTALLATION

Cautions:

DESIGN LED 36 Pro™

©Elation Professional, Los Angeles Ca. 11 www.ElationLighting.com

For added protection mount the fixtures in areas outside walking paths, seating areas, and

away from areas were unauthorized personnel might reach the fixture.

Before mounting the fixture to any surface, make sure that the installation area can hold a

minimum point load of 10 times the device’s weight.

Fixture installation must always be secured with a secondary safety attachment, such as an

appropriate safety cable.

To avoid injury, never stand directly below the device when mounting, removing, or servicing

the fixture.

Refer to regulations BGV C1 (formerly VBG 70) and DIN VDE0711-217

for proper installation in Europe To ensure proper installation, only

qualified staff should attempt installation.

Mounting points

Overhead mounting requires extensive experience, including amongst others calculating

working load limits, a fine knowledge of the installation material being used, and periodic

safety inspection of all installation material and the fixture. If you lack these qualifications, do

not attempt the installation yourself. Improper installation can result in bodily injury.

CAUTION!

Be sure a qualified electrician performs all electrical

connections.

Be sure to complete all rigging and installation procedures before connecting the main

power cord to the appropriate wall outlet.

DESIGN LED 36 Pro™

©Elation Professional, Los Angeles Ca. 12 www.ElationLighting.com

Mounting

The Design LED 36 Pro™ is fully operational in any mounting position, hanging

upside-down, side mounted, or set on a flat level surface, etc. Be sure this fixture is kept at

least 0.5m (1.5 feet) away from any flammable materials (decoration etc.). When clamp

mounting; always use and install the supplied safety cable as an added safety measure to

prevent accidental damage in the event of a clamp failure. See the image below.

Clamp Mounting

The Design LED 36 Pro™ provides a unique mounting bracket assembly that allows the unit

to stand on a flat surface or to be hung on truss via a clamp in any safe position (see the

illustration above). Regardless of the mounting option you choose please be sure to refer to

the safety guidelines in this manual to avoid damage to the unit and/or personal injury.

When mounting this fixture to truss be sure to secure an appropriately rated clamp to the

hanging yoke using a M10 screw fitted through the center hole of the hanging yoke. As an

DESIGN LED 36 Pro™

©Elation Professional, Los Angeles Ca. 13 www.ElationLighting.com

added safety measure be sure to attach at least one properly rated safety cable to the fixture.

See illustrations below.

Securing the Design LED 36 Pro™

Always be sure to secure your fixture with a safety cable when

suspending the unit from truss or other means. The fixture

provides a built-in rigging point for a safety cable as illustrated

above. Be sure to only use the designated rigging point for the

safety cable and never secure a safety cable to the hanging

bracket.

DESIGN LED 36 Pro™

©Elation Professional, Los Angeles Ca. 14 www.ElationLighting.com

7. UNDERSTANDING DMX

DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used by most

lighting and controller manufactures as a form of communication between intelligent fixtures

and controllers. DMX allows all makes and models of different manufactures to be linked

together and operate from a single controller. This is possible as long as all the fixtures and

the controller are DMX compliant. A DMX controller sends the DMX data instructions to a

fixture allowing the user to control the different aspects of an intelligent light. DMX data is

sent out as serial data that travels from fixture to fixture via data “IN” and “OUT” leads

located on the fixtures (most controllers will only have output jacks).

DMX Linking: To ensure proper DMX data transmission, always use proper DMX cables

and a terminator. When using several DMX fixtures try to use the shortest cable path

possible. Never split a DMX line with a “Y” style connector. The order in which the fixtures

are connected in a DMX line does not influence the DMX addressing. For example; a fixture

assigned a DMX address of 1 may be placed anywhere in the DMX chain, at the beginning,

at the end, or anywhere in the middle. The DMX controller knows to send data assigned to

address 1 to that fixture no matter where it is located in the DMX chain. The Design LED 36

Pro™ can be controlled via DMX-512 protocol. The Design LED 36 Pro™ is a fixture that

can operate in 3, 4, or 6 DMX channels (see page 21 for the different DMX traits). The DMX

address is set electronically using the controls on the LED menu.

You can chain multiple fixtures together through serial linking. Using the IP rated signal

cables provided through Elation. Always be sure to daisy-chain your in and out data

connections, never split or “Y” your DMX connections unless you are using an approved

DMX splitter such as the Elation Opto Branch 4™ or DMX Branch/4™.

DESIGN LED 36 Pro™

©Elation Professional, Los Angeles Ca. 15 www.ElationLighting.com

DMX-512 connection with DMX terminator

A DMX terminator should be used in all DMX lines especially in longer runs. The use of a

terminator may avoid erratic behavior in your DMX line. A terminator is a 120 ohm 1/4 watt

resistor that is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA

-). This fixture is inserted in the female XLR connector of the last fixture in your daisy chain

to terminate the line. Using a line terminator (Elation part: DMX T PACK) will decrease the

possibilities of erratic behavior.

5-Pin XLR DMX Connectors. Some manufactures use 5-pin XLR connectors for DATA

transmission in place of 3-pin. 5-pin XLR fixtures may be implemented in a 3-pin XLR DMX

line. When inserting standard 5-pin XLR connectors in to a 3-pin line a cable adaptor must

be used, these adaptors are readily available at most electric stores. The following chart

details a proper cable conversion.

Fixture DMX addressing;

All fixtures should be given a DMX starting address when using a DMX controller, so the

DESIGN LED 36 Pro™

©Elation Professional, Los Angeles Ca. 16 www.ElationLighting.com

correct fixture responds to the correct control signal. This digital starting address is the

channel number from which the fixture starts to “listen” to the digital control information sent

out from the DMX controller. The allocation of this starting DMX address is achieved by

setting the correct DMX address on the digital display located on the back of the fixture.

You can set the same starting address for all fixtures or a group of fixtures, or set different

address for each individual fixture. Be advised that setting all you fixtures to the same DMX

address will subsequently control all fixtures in the same fashion, in other words, changing

the settings of one channel will affect all the fixtures simultaneously.

If you set each fixture to a different DMX address, each unit will start to “listen” to the

channel number you have set, based on the quantity of control channels (DMX channels) of

each fixture. That means changing the settings of one channel will only affect the selected

fixture.

In the case of the Design LED 36 Pro™, which is up to a six channel fixture (default may also

be set to three or four channels), you should set the starting DMX address of the first unit to

1, the second unit to 4 (3 + 1), the third unit to 7 (3 + 4), and so on.

Note: During start-up the Design LED 36 Pro™ will automatically detect whether a DMX

data signal is being received or not. If a DMX data signal is being received, the display will

show "A.XXX" (XXX representing the actual DMX address). If the fixture is not receiving a

DMX signal the display will flash "A.XXX" (XXX representing the actual DMX address).

If your fixture is connected to a DMX controller and the display is flashing (not receiving a

DMX signal), please check the following:

- The 3-pin or 5-pin XLR plug (cable with DMX signal from controller) may not be

connected or is not inserted completely into the DMX input jack.

- The DMX controller is switched off or defective.

- The DMX cable or connector is defective.

- A DMX terminator has been inserted into the last fixture in your DMX chain.

DESIGN LED 36 Pro™

©Elation Professional, Los Angeles Ca. 17 www.ElationLighting.com

8. DISPLAY LED INDICATORS.

The Design LED 36 Pro ™ has two LED indicators on the display. These indicators are

designed to give a quick visual indication of the fixtures’ status. The illustration below details

the functionality of the LED indicators.

.

. . .

Lamp on

Lamp on

DMX OK

DMX OK

NO DMX

NO DMX

Lamp off

Lamp off

The first LED indicators represents DMX signal:

• If the indicators is on a clean DMX signal is present

• If the indicator is off there is no DMX signal present

The second LED indicator represents lamp condition; this is only applicable to fixtures with

traditional lamp sources.

DESIGN LED 36 Pro™

©Elation Professional, Los Angeles Ca. 18 www.ElationLighting.com

9. DISPLAY MENU

Default settings shaded.

ADDR

AXXX (1-512)

Set the starting DMX address

DISP

ON/OFF

Display “Blackout” function. When activated the
display will automatically blackout when not in use.

FLIP

ON/OFF

When “ON” this function rotate the display 180˚

3 CH

3 DMX CHANNELS (RGB)
4 CH

4 DMX CHANNELS (RGB+MASTER DIM)

CHAN
6 CH

6 DMX CHANNELS

MODE

SLAV

ON/OFF

UNIT FUNCTIONS AS SLAVE

MAST

Fixture will function as a master unit in Master/Slave
mode

CNTL

ALON

Fixture will function “Stand Alone” mode
BLAC

BLACKOUT – LED OUTPUT OFF

RED

RXXX

Manual Mode - Manual setting of RED levels

GREN

GXXX

Manual Mode - Manual setting of GREEN levels

BLUE

BXXX

Manual Mode - Manual setting of BLUE levels

MANU

COLR

STRB

SXXX

Manual Mode - Manual setting of STROBE rate

SPED

XXX

Adjust program 1 speed

FADE

XXX

Adjust program 1 fade time

CHS1

STRB

XXX

Adjust strobe rate of program 1

SPED

XXX

Adjust program 2 speed

FADE

XXX

Adjust program 2 fade time

CHS2

STRB

XXX

Adjust strobe rate of program 2

SPED

XXX

Adjust program 3 speed

FADE

XXX

Adjust program 3 fade time

CHS3

STRB

XXX

Adjust strobe rate of program 3

CHAS

CHS4

SPED

XXX

Adjust program 4 speed

DESIGN LED 36 Pro™

©Elation Professional, Los Angeles Ca. 19 www.ElationLighting.com

FADE

XXX

Adjust program 4 fade time

STRB

XXX

Adjust strobe rate of program 4

SPED

XXX

Adjust program 5 speed

FADE

XXX

Adjust program 5 fade time

CHS5

STRB

XXX

Adjust strobe rate of program 5

SPED

XXX

Adjust program 6 speed

FADE

XXX

Adjust program 6 fade time

CHS6

STRB

XXX

Adjust strobe rate of program 6

SPED

XXX

Adjust program 7 speed

FADE

XXX

Adjust program 7 fade time

CHS7

STRB

XXX

Adjust strobe rate of program 7

SPED

XXX

Adjust program 8 speed

FADE

XXX

Adjust program 8 fade time

CHS8

STRB

XXX

Adjust strobe rate of program 8

DIMR

MOD1

Standard - Fixture will function with a stepping
dimmer rate

MOD2

Linear - Fixture will function with a dimming rate of
0~100%

LODA

Reset to Fixture to the Factory Default Settings

OTHR

VER

V X.X

“X.X’ will represent the fixture’s current firmware
version

Note:

1) If the fixture does not receive a DMX signal the menu display will flash repeatedly.

2) SPED: Adjust the hold time for each scene in built-in chase programs.

3) FADE: Adjust the fade time between each scene in the built-in programs.

DESIGN LED 36 Pro™

©Elation Professional, Los Angeles Ca. 20 www.ElationLighting.com

10. DMX TRAITS

DMX Operation Notes:

The fixture will function in DMX mode whenever the unit is receiving a DMX signal. Please

note that this will override all manual settings.

This unit will keep and retain the last DMX command in the event of DMX signal failure. To

reset the fixture you must turn the power off.

DMX CHANNEL TRAITS

The charts below and on the preceding pages outline the different DMX traits for the three

different DMX modes.

3-Channel mode: In this mode channel one controls all the red LEDs, channel two controls

all the green LEDs, and channels three controls all the blue LEDs. 3-Channel Mode: The

chart below details the DMX channel layout for 3-channel assignment.

DESIGN LED 36 Pro™

©Elation Professional, Los Angeles Ca. 21 www.ElationLighting.com

DMX channel’s functions and their values (3-Channel Mode):

Channel 1 - Red:

0-255

Red (0-Black, 255 - 100% Red)

Channel 2 - Green:

0-255

Green (0-Black, 255 - 100% Green)

Channel 3 - Blue:

0-255

Blue (0-Black, 255 - 100% Blue)

4-Channel mode: In this mode channel one controls all the red LEDs, channel two controls

all the green LEDs, channels three controls all the blue LEDs, and channel four-- will control

the master dimming level. 4-Channel Mode: The chart below details the DMX channel layout

for 4-channel assignment.

DESIGN LED 36 Pro™

©Elation Professional, Los Angeles Ca. 22 www.ElationLighting.com

DMX channel’s functions and their values (4-Channel Mode):

Channel 1 - Red:

0-255

Red (0-Black, 255 - 100% Red)

Channel 2 - Green:

0-255

Green (0-Black, 255 - 100% Green)

Channel 3 - Blue:

0-255

Blue (0-Black, 255 - 100% Blue)

Channel 4 - Dimming / Program Speed Control

This channel has two functions depending on the operating mode. When running the built-in

programs this channel will control the program speed.

0-255

Dimming (0%-100%) ~ Normal Operation

0-255

Speed (min to max) ~ When running built-in programs on channel 4

6-Channel mode: In this mode channels 1~3 are used to control the RGB LEDs and

channels 4~6 will control special features. 6-Channel Mode: The charts below and on the

next page detail the DMX channel layout for 6-channel assignment.

DESIGN LED 36 Pro™

©Elation Professional, Los Angeles Ca. 23 www.ElationLighting.com

DMX channel’s functions and their values (6-Channel Mode):

Channel 1 - Red:

0-255

Red (0-Black, 255-100% Red)

Channel 2 - Green:

0-255

Green (0-Black, 255- 100% Green)

Channel 3 - Blue:

0-255

Blue (0-Black, 255- 100% Blue)

Channel 4 - Internal programs:

0-10

No function

11-40

Internal program 1

41-70

Internal program 2

71-100

Internal program 3

101-130

Internal program 4

131-160

Internal program 5

161-190

Internal program 6

191-220

Internal program 7

221-255

Internal program 8

Channel 5 - Strobe:

0

No function

1~95

Strobe effect slow to fast

96-127

No function

128-159

Pulse effect in sequences

160-191

No function

192-223

Random strobe effect slow to fast

224-255

No function

DESIGN LED 36 Pro™

©Elation Professional, Los Angeles Ca. 24 www.ElationLighting.com

Channel 6 - General dimming / Program Speed Control

This channel has two functions depending on the operating mode. When running the built-in

programs this channel will control the program speed, when not running the built-in programs

this channel will control master dimming.

0-255

Dimming (0%-100%) ~ Normal Operation

0-255

Speed (min to max) ~ When running built-in programs on channel 4

DESIGN LED 36 Pro™

©Elation Professional, Los Angeles Ca. 25 www.ElationLighting.com

11. LENS REPLACEMENT

The Design LED 36 Pro comes with a removable front cover that allows the lens assembly to

be changed out to achieve different beam angles.

The lens cover is held in place by four 5mm Allen screws. To access the lens kit, remove the

bard door assembly (if so attached) to access the four 5mm Allen screws, then loosen the

screws. The screws are held in by clips so they cannot be removed completely. Lift the outer

cover to access the lens kit. The lens kit is held in by four Phillips screws, remove these

screws to remove the lens kit. Replace the lens kit with the preferred option and reassemble

in reverse order. Be sure to align the rubber seal properly when reassembling.

DESIGN LED 36 Pro™

©Elation Professional, Los Angeles Ca. 26 www.ElationLighting.com

12. CLEANING AND MAINTENANCE

Consider the following points during normal service and inspection:

1. Be sure all screws and fasteners are securely tightened at all times. Lose screws may

fall out during normal operation resulting in damage or injury as larger parts could fall.

2. Electric power supply cables must not show any damage, material fatigue or

sediments. Never remove the ground prong from the power cable.

Further instructions depending on the installation spot and usage have to be adhered by a

skilled installer and any safety problems have to be removed.

We recommend a frequent cleaning of the device. Please use a moist, lint- free cloth. Never

use alcohol or solvents.

There are no user serviceable parts inside this fixture, please refer all other service issues to

an authorized Elation service technician.

Should you need any spare parts, please order genuine parts from your local dealer.

DESIGN LED 36 Pro™

©Elation Professional, Los Angeles Ca. 27 www.ElationLighting.com

13. 2-YEAR LIMITED WARRANTY

A. Elation Professional® hereby warrants, to the original purchaser, Elation Professional®

products to be free of manufacturing defects in material and workmanship for a period of two

years, (730 days) from the date of purchase. This warranty shall be valid only if the product

is purchased within the United States of America, including possessions and territories. It is

the owner’s responsibility to establish the date and place of purchase by acceptable

evidence, at the time service is sought.

B. For warranty service, send the product only to the Elation Professional® factory. All

shipping charges must be pre-paid. If the requested repairs or service (including parts

replacement) are within the terms of this warranty, Elation Professional® will pay return

shipping charges only to a designated point within the United States. If the entire instrument

is sent, it must be shipped in its original package. No accessories should be shipped with the

product. If any accessories are shipped with the product, Elation Professional® shall have no

liability what so ever for loss of or damage to any such accessories, nor for the safe return

thereof.

C. This warranty is void if the serial number has been altered or removed; if the product is

modified in any manner which Elation Professional® concludes, after inspection, affects the

reliability of the product; if the product has been repaired or serviced by anyone other than

the Elation Professional® factory unless prior written authorization was issued to purchaser

by Elation Professional®; if the product is damaged because not properly maintained as set

forth in the instruction manual.

D. This is not a service contract, and this warranty does not include maintenance, cleaning

or periodic check-up. During the period specified above, Elation Professional® will replace

defective parts at its expense, and will absorb all expenses for warranty service and repair

labor by reason of defects in material or workmanship. The sole responsibility of Elation

Professional® under this warranty shall be limited to the repair of the product, or replacement

thereof, including parts, at the sole discretion of Elation Professional®. All products covered

by this warranty were manufactured after January 1, 1990, and bare identifying marks to that

DESIGN LED 36 Pro™

©Elation Professional, Los Angeles Ca. 28 www.ElationLighting.com

effect.

E. Elation Professional® reserves the right to make changes in design and/or improvements

upon its products without any obligation to include these changes in any products

theretofore manufactured.

F. No warranty, whether expressed or implied, is given or made with respect to any

accessory supplied with products described above. Except to the extent prohibited by

applicable law, all implied warranties made by Elation Professional® in connection with this

product, including warranties of merchantability or fitness, are limited in duration to the

warranty period set forth above. And no warranties, whether expressed or implied, including

warranties of merchantability or fitness, shall apply to this product after said period has

expired. The consumer’s and or Dealer’s sole remedy shall be such repair or replacement as

is expressly provided above; and under no circumstances shall Elation Professional® be

liable for any loss or damage, direct or consequential, arising out of the use of, or inability to

use, this product.

G. This warranty is the only written warranty applicable to Elation Professional® Products

and supersedes all prior warranties and written descriptions of warranty terms and

conditions heretofore published.

DESIGN LED 36 Pro™

©Elation Professional, Los Angeles Ca. 29 www.ElationLighting.com

14. PHOTOMETRIC DATA

DESIGN LED 36 Pro™

©Elation Professional, Los Angeles Ca. 30 www.ElationLighting.com

DESIGN LED 36 Pro™

©Elation Professional, Los Angeles Ca. 31 www.ElationLighting.com

DESIGN LED 36 Pro™

©Elation Professional, Los Angeles Ca. 32 www.ElationLighting.com

15. DIMENSIONAL DRAWINGS

DESIGN LED 36 Pro™

©Elation Professional, Los Angeles Ca. 33 www.ElationLighting.com

16. CIRCUIT SCHEMATIC

DESIGN LED 36 Pro™

©Elation Professional, Los Angeles Ca. 34 www.ElationLighting.com

17. TECHNICAL SPECIFICATIONS

Power supply: 100v~240v / 50Hz~60Hz AC

Power consumption: Maximum 150w

LED Configuration: 36 x 3 Watt

(12 x Red, 12 x Green 12 x Blue)

Weight: 6 Kgs / 15.2Lbs

DMX Channels: 6, 4, or 3 Channel mode

DMX Drive: Standard DMX-512,

3-Pin XLR; [+] = Pin 3 [-] = Pin 2 [Ground] = Pin 1.

Color Mixing: RGB Color Additive Mixing

Beam Angle: 48.5˚ (25˚ Lens) / Optional 15˚ & 45˚ Lenses

Fuse: GMA 220v~2A (Internal)

Dimmer: Continuous Dimming 0~100%

Strobe: Electronic Strobe 0~18 Fps

Lamp Life: 100,000 Hours Rated Life

Dimensions: (232 x 220 x 260) mm

9.13” x 8.66” 10.24”

Please Note: Specifications and improvements in the design of this unit and this manual are

subject to change without any prior written notice.

Rev. 12/10/2008 - visage

Elation Professional

6122 S. Eastern Ave.

Los Angeles, CA. 90040

323-582-3322 / 323-832-9142 fax

www.ElationLighting.com /

[e-mail]