• Please read and follow these safety instructions.
• Keep them safe for future reference.
• Observe all warnings on the speaker and in the manual. Please check the speaker for damage before
use. The speaker must be in perfect working condition. Damaged parts may lead to personal injury.
2. Use only as directed
• Connect the speaker(s) according to the instructions in the manual.
• Many ELAC speakers are equipped with spikes and/or anti-slip feet. They are explicitly provided for
levelling the speaker. For levelling on an uneven floor, unscrew the spikes or anti-slip feet by 2-3 turns of
thread. The speaker should always be in perfect vertical alignment: the stability of the speaker must not
be compromised by using spikes or anti-slip feet as the speaker may tip-over.
3. Location
• Install the speakers on a level surface only
• When choosing the location of these speakers do not place them in locations that are:
• In direct sunlight
• Very humid
• Prone to vibrations
• Exceptionally hot or cold
• Near CRT Televisions (the speakers are not magnetically shielded and may cause color issues
with a CRT based TV)
• Close to magnetic cards (Since the speakers are not magnetically shielded placing magnetic
cards such as credit cards or commuter cards may cause them to fail).
WARNING! Please ensure the product is perfectly stable to avoid injury from tip-over. Please note, that stability
can be increased by using spikes on carpeted surfaces. However, the mounting of spikes must be carried out
carefully due to their very sharp ends which may cause injuries. The stability on slippery floors can be increased
by using Velcro fastening tape or double-sided adhesive tape. Do not install the speaker near any heat sources
such as radiators, heating valves, stoves, or other apparatus (including amplifiers) that produce heat, or in areas
where there is a risk of explosion.
• Do not block any ventilation openings. Install in accordance with the instructions.
• Do not install the speaker in a closed rack or in a closed cupboard.
• Do not put burning candles on or near the speaker.
• Do not install the speaker near transformers because electromagnetic stray fields can cause hum noise
on woofers.
• In combination with certain materials / lacquers / material surfaces, anti-slip feet or spike washers may
cause colored imprints on the surfaces.
ELAC Navis Speakers | www.elac.com | Page 1
4. Overload
• Extreme overload of the device due to very high volume may cause damage to individual components.
Because of the possible danger, you should never leave loudspeakers under extreme overload
conditions unattended.
5. Service
DANGER! Do not open the cabinet because the components and conductors may carry current! Servicing to be
carried out by qualified service personnel only.
• Servicing is required when the loudspeaker has been damaged in any way, such as damage to
the power supply cord or the plug, or when liquid has been spilled or objects have fallen onto the
loudspeaker, the speaker has been exposed to rain or moisture, does not operate normally, or has been
dropped. To reduce the risk of electric shock, do not open the loudspeaker. Servicing should be carried
out by qualified service personnel only.
6. Cleaning
NOTE: Clean only with soft, smooth cloth or with dust brush. Do not use scouring agents, alcohol, benzene,
furniture polish or other agents for cleaning! Modern furniture is often coated with multiple varnishes and
plastics which can be treated with chemical agents. Some of these agents contain substances which degrade or
soften the rubber feet. Therefore we advise that you place an anti-slip mat underneath the loudspeaker(s).
7. Volume
CAUTION! Continuous high volume may cause severe damage to your hearing. Please listen responsibly.
8. Disposal
The packaging is made from recyclable materials. Dispose of this in an environmentally friendly manner. At
end of life do not dispose of the speaker(s) with standard household waste. The speaker must be recycled in
accordance with local legislation. Ask your local government for further information on recycling as the device
contains valuable raw materials. Disable the speaker(s) before disposal.
9. Compliance Information for the Wireless Transmitter
The term “IC:” before the radio certification number only signifies that Industry Canada technical specifications
were met. This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm between the
radiator and your body. This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that may cause undesired operation of the device.
To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the
equivalent isotopically radiated power is not more than that permitted for successful communication.
ELAC Navis Speakers | www.elac.com | Page 2
Philosophy
Thank you for purchasing this ELAC product.
Since the time we started (1926), ELAC has always striven to achieve the very best.
Your new ELAC speakers are built to the highest standards using high-quality components that are carefully
constructed to deliver the best-in-class sound quality. They are developed by a passionate group of individuals
whose sole purpose is to bring a new dimension of sound quality into your home. Enjoy!
Before Use
Avoid damage to the speakers and other components:
• Carefully unbox the speakers to avoid physically damaging your speakers.
• Ensure your equipment is turned o before connecting speakers.
ELAC Navis Speakers | www.elac.com | Page 3
Controls and Indicators
1. RCA Input — This connection is used to connect the speaker to your pre-amp/AV receiver with RCA connections
2. XLR Inputs —This connection is used when your pre-amplifier features XLR balanced outputs.
3. Input Switch— Allows for selection of the RCA, XLR, or Wireless
Input
4. Left/Right Switch— This switch determines if the speaker is the left of right speaker when the wireless input is being used.
5. LF EQ Switch—This switch allows you to tailor the low frequency output to your liking. (See page 8 for more details)
6. MF EQ Switch—This switch allows you to tailor the mid- range output to your liking. (See page 8 for more details)
7. HF EQ Switch—This switch allows you to tailor the high- frequency output to your liking. (See page 8 for more details)
8. HP Filter — This switch applies a High Pass filter to the speaker. This would be used in conjunction with a subwoofer. (See page 8 for more details)
9. Gain Adjustment—This switch allows you to adjust the input left gain of the speaker. (See page 8 for more details)
10. AC Inlet — This inlet is a standard IEC power jack. Use the supplied power cord to connect the speaker to an available AC outlet.
11. Primary Power Switch—This switch is used to turn on/o primary power to the speaker
12. Pair Button —This button is used when pairing the speakers with an AirX² transmitter
13. Wireless LED—The light is used during the pairing process with an AirX² transmitter
14. Voltage Selector—This switch is used for selecting the correct AC Voltage for your country.
5
6
13
7
12
8
3
4
9
1
2
11
14
ELAC Navis Speakers | www.elac.com | Page 4
10
Installing the base and spikes (AF-51 Only)
Using the included outrigger plate provides a wider support base for the speaker cabinet and should be
installed. The included spikes improve stability on uneven surfaces and thickly carpeted floors. Please use
caution when dealing with the spikes as they are sharp.
IMPORTANT: When using these spikes on hard surfaces such as wood or tile floors be sure to use the provided
floor discs to protect your floor from damage.
1
2
3
4
IMPORTANT: In order to prevent scratching or damage
to the cabinet, turn the speaker upside down onto a soft
surface while you attach the outrigger plate and spikes.
We highly recommend a second person help with this
process. Also, please use caution when picking up and
moving the steel outrigger plate. It is very HEAVY! Do
not leave the speaker upside down
Attach the spike mounts and spikes and to the bottom
steel plate as shown in the diagram to the right. Please
be careful when picking on the steel outrigger plate. It
is heavy.
Place the steel outrigger plate on the bottom of the
speaker and attach it using the four supplied machine
screws as shown in the diagram to the right. Please
exercise caution. These items are heavy.
Now carefully turn the speaker back upright. We
suggest using a second person for this process. Please
be careful of the spikes. They are sharp. Please use the
floor discs if you have hardwood or tile floors.
5
ELAC Navis Speakers | www.elac.com | Page 5
Once the speaker has been moved to the final location,
rotate the spike until the speaker is level.
Connecting the Speakers
The Navis speakers can be connected three dierent ways Wired RCA Unbalanced, Wired XLR Balanced, or
Wireless (AirX²). CAUTION—THE NAVIS SPEAKERS DO NOT HAVE A VOLUME CONTROL. IF CONNECTED
DIRECTLY TO A FIXED OUTPUT SOURCE THE VOLUME WILL BE AT MAXIMUM LEVEL AND MAY DAMAGE
THE SPEAKERS AND YOUR HEARING. ONLY USE WITH VARIABLE OUTPUT SOURCES!!!
Connecting the Navis Speakers using wired (RCA or XLR) connections
1. Using an RCA or XLR interconnect cable, connect the variable pre-outputs from your pre-amplifier to the RCA/
XLR input on each speaker.
2. Select the RCA or XLR input using the source switch on the rear of the each speaker.
ELAC Navis Speakers | www.elac.com | Page 6
→
→
Making Adjustments
The Navis speakers provide several adjustments to tailor the sound to your specific environment or taste. Use
the below guide to aid it setting up. Please note these settings should always be set the same on both speakers
(Except for the Left/Right switch when using the wireless input).
Low Frequency EQ (LF EQ)—This adjustment allows you to
decrease or increase the low frequency output of the Navis
speaker to best match into your room. +1db can be used if
you like a little more bass or if your room is bass light. –4db
should be used if you choose to place the speakers closer
to the room boundaries.
Mid Frequency EQ (MF EQ)—This adjustment allows you to
decrease or increase the mid frequency output of the Navis
speaker to best match into your room. +1db can be used to
increase detail or vocal projection, the –1db position can be
used to oset a room with “Bright” acoustics.
High Frequency EQ (HF EQ)—This adjustment allows you
to decrease or increase the high frequency output of the
Navis speaker to best match into your room. +1db can
be used to oset a heavy soft furnished room or add an
extra sense of “air”. The –1db setting can be used to tame
aggressive recordings or to oset a “hard” sounding room.
High Pass Filter (HP Filter) - This adjustment allows the
addition of a subwoofer to your Navis speaker system. It
provides a choice cuto filters to allow optimum match with
your subwoofers capabilities. This setting should be set to
“FLAT” when no subwoofer is being used.
Gain Adjustment (GAIN) - This adjustment allows you to
match the input sensitivity of the speaker to the gain of
your system. If when setting your volume level you cannot
turn the system up loud enough use the HIGH setting,
if alternatively you find that the speaker is too loud at a
moderate volume control setting then use the LOW setting.
Pairing the Navis Speakers with am AirX wireless transmitter is very simple. Please follow the below steps to
complete the process.
1. Press and hold the Wireless Pair button on the Navis speakers until the LED begins to flash rapidly (Around 2
times per second).
2. Press and hold the Wireless Pair button on the back of the AirX² wireless transmitter until the wireless pair LED on the Navis Speakers stops flashing and goes o (No LED means the speaker is wirelessly paired.)
3. Repeat with additional speakers/subwoofers (Up to 3 units)
DC IN
9V 0.8A
MODEL NUMBER:DS-C101W-G
OUTPUTOUTPUT
←
OPT 1COAX 1ETHERNET INCOAX 2OPT 2
Wireless Pair Button Discovery Connect
BT PAIR
/RESET
WL PAIR
←
LR
ANALOG
Wireless Pair Button Navis Speakers
ELAC Navis Speakers | www.elac.com | Page 8
Speaker Placement
Achieve maximum performance and optimal sound quality from your ELAC Navis speakers with proper speaker
placement and set-up. While not all rooms are the same, use the following guidelines to configure the speakers
for your particular room. There are no “exact” rules or boundaries in setting up your speakers but the following
suggestions will help optimize your desired results. Remember the best sound set-up is what sounds best for
you so don’t be afraid to experiment and make adjustments to the placement and directivity of the speakers.
Walls
1’ –2’ FEET
1’ –2’ FEET
Place the speakers approximately one to two feet away (fig. 1) from boundaries such as wall(s) and especially
corners. Close proximity to a side or rear wall will enhance bass performance (output), but being too close
(particularly to a corner) may result in bass that is unnatural. If a corner location is unavoidable, try to position the
loudspeaker so that the distance to the rear wall is not equal to the distance to the side wall.
ELAC Navis Speakers | www.elac.com | Page 9
Stereo Setup
• For the best results and the most realistic stereo image and lifelike sound, place the speakers so that an
equilateral triangle (fig. 2) is created between the speakers and your favorite listening position. This set
up creates the optimum imaging performance.
• If you find that your Navis left and right speakers are too far apart, angle (toe in) them towards the
listening position to gain a more focused central image.
2–CHANNEL STEREO SETUP
2–CHANNEL STEREO SETUP
2–CHANNEL STEREO SETUP
ELAC Navis Speakers | www.elac.com | Page 10
SPECIFICATIONS
SpecsARB51ARF51
Speaker type:3-Way Powered3-Way Powered
Tweeter:1" Soft Dome Concentrically Mounted1" Soft Dome Concentrically Mounted
Midrange4" Aluminum 4" Aluminum
Woofer:5-1/4" Aluminum3 x 5-1/4" Aluminum
Frequency Response44Hz - 28kHz43Hz - 28kHz
Crossover Frequency2.2kHz / 260Hz2.2kHz / 260Hz
Total Amplifier Power300 Watts Total300 Watts Total
Bass Amplifier160 Watt Bash Amplifier160 Watt Bash Amplifier
Midrange Amplifier100 Watt Bash Amplifier100 Watt Bash Amplifier
Tweeter Amplifier40 Watt Class AB Amplifier40 Watt Class AB Amplifier
InputsRCA / XLR / AirX² WirelessRCA / XLR / AirX² Wireless
Cabinet finishes:Gloss Black, Gloss White, Gloss Ebony EmaraGloss Black, Gloss White, Gloss Ebony Emara
Height:13.58"40.35"
Width:7.44"7.44"
Depth:9.45"9.45"
Net weight (each):35.7lbs46.3lbs
ELAC Navis Speakers | www.elac.com | Page 11
ELAC Americas Inc.
North America Limited Liability Warranty
Powered Speakers
ELAC Americas Inc. warrants to the original purchaser that this product be free from defects and or workmanship
for a period of 3 (Three) years on the cabinet and speaker driver and 1 (One) year on the amplifier from the
original date of purchase. During this time period, repair or replacement of parts will be free of charge to the
original owner (See below limitations). Shipping to and return from the repair center will be the responsibility of
the original purchaser.
Limitations
• Warranty begins on the date of original purchase from an authorized ELAC Americas Inc. dealer.
• Product is warranted only if used in home applications. Commercial use of this product is not warranted.
• Product that has been modified or altered in anyway will not be warranted.
• Product that has been abused or subjected to faulty equipment will not be warranted.
• Products with defaced or removed serial numbers will not be warranted.
If service is required
In the event that service is required, please contact ELAC America at 714-252-8843 or at
customerservice@elac.us to arrange for service or replacement. You will be responsible to provide proof of
purchase (Copy or original sales receipt). Shipping to and from our repair center will be the responsibility of the
original purchaser.
Warranty Outside of North America
This warranty applies to products purchased and used in the United States and Canada. For warranty claims
outside of North America please contact the local dealer/distributor in the country of purchase.
ELAC Navis Speakers | www.elac.com | Page 12
Loading...
+ 28 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.