User’s Manual
Color LCD Monitor
Important
Please read this “User’s Manual”, and “PRECAUTIONS” (separate
volume) carefully to familiarize yourself with safe and effective usage.
• Refer to the “Setup Guide” for information on the installation /
connection of the monitor.
• For the latest product information including the “User’s Manual”,
refer to our web site :
www.eizoglobal.com
Location of Caution Statement
This product has been adjusted specically for use in the region to which it was originally shipped. If
operated outside this region, the product may not perform as stated in the specications.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by
any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.
EIZO Corporation is under no obligation to hold any submitted material or information condential unless
prior arrangements are made pursuant to EIZO Corporation’s receipt of said information. Although every
effort has been made to ensure that this manual provides up-to-date information, please note that EIZO
monitor specications are subject to change without notice.
2
Notice for this monitor
This product is suited to general purposes like creating documents, viewing multimedia content (Assuming
usage of approximately 12 hours per day).
If using this product for the following kinds of applications, where an extremely high degree of reliability and
safety is required, then measures should be in place to maintain safety while using this product.
• Transportation equipment (ships, aircraft, trains, and automobiles)
• Safety devices (Disaster prevention systems, security control systems, etc.)
• Life-critical devices (medical devices, such as life-support devices and operating room devices)
• Nuclear energy control devices (Nuclear energy control systems, security control systems of nuclear facilities, etc.)
• Major system communication devices (operation control systems of transportation systems, air trafc control systems, etc.)
This product has been adjusted specically for use in the region to which it was originally shipped. If the
product is used outside the region, it may not operate as specied in the specications.
This product may not be covered by warranty for uses other than those described in this manual.
The specications noted in this manual are only applicable when the following are used:
• Power cords provided with the product
• Signal cables specied by us
Only use optional products manufactured or specied by us with this product.
If you place this product on a lacquer-coated desk, the color may adhere to the bottom of the stand due to
the composition of the rubber. Check the desk surface before use.
It takes about 30 minutes (under our measurement conditions) for the monitor display to stabilize. Please
wait 30 minutes or more after the monitor power has been turned on, and then adjust the monitor.
Monitors should be set to a lower brightness to prevent a loss in the screen quality caused by long-term use
and to maintain stable use.
When the screen image is changed after displaying the same image for extended periods of time, an
afterimage may appear. Use the screen saver or power save function to avoid displaying the same image for
extended periods of time. Depending on the image, an afterimage may appear even if it was displayed for
a short period of time. To remove such a phenomenon, change the image or keep the power turned off for
several hours.
If the monitor displays continuously over a long period of time, dark smudges or burn-in may appear. To
maximize the life of the monitor, we recommend the monitor be turned off periodically.
Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime (refer
to “Cleaning” (page 4)).
The LCD panel is manufactured using high-precision technology. Although, missing pixels or lit pixels may
appear on the LCD panel, this is not a malfunction. Percentage of effective dots: 99.9994 % or higher.
The backlight of the LCD panel has a xed lifetime. Depending on the usage pattern, such as usage for
long continuous periods, the lifespan of the backlight may run out sooner, requiring replacement. When the
screen becomes dark or begins to icker, please contact your local EIZO representative.
Do not press on the LCD panel or edge of the frame strongly, as this may result in display malfunctions, such
as interference patterns, etc. If pressure is continuously applied to the LCD panel surface, the liquid crystal
may deteriorate or the LCD panel may be damaged. (If the pressure marks remain on the panel, leave the
monitor with a black or white screen. The symptom may disappear.)
Do not scratch or press on the LCD panel with any sharp objects, at this may result in damage to the LCD
panel. Do not attempt to brush with tissues as this may scratch the panel.
Notice for this monitor
3
When the monitor is cold and brought into a room or the room temperature goes up quickly, dew
condensation may occur on the interior and exterior surfaces of the monitor. In that case, do not turn the
monitor on. Instead wait until the dew condensation disappears, otherwise it may cause some damage to the
monitor.
Cleaning
The stains on the cabinet and LCD panel surface can be removed by moistening part of a soft cloth with water.
Attention
• Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the cabinet
or LCD panel, and also quality deterioration of the image.
• Never use thinner, benzine, wax, or abrasive cleaner as they may damage the cabinet or LCD panel surface.
Note
• It is recommended that ScreenCleaner (available as an option) be used to clean the cabinet and LCD panel surface.
To use the monitor comfortably
• An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor
according to the environmental conditions.
• Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.
Notice for this monitor
4
CONTENTS
Notice for this monitor ......................................... 3
Cleaning .................................................................... 4
To use the monitor comfortably ............................. 4
CONTENTS ............................................................. 5
Chapter 1 Introduction ....................................... 6
1-1. Features ......................................................... 6
DisplayPort Daisy Chain Connection .............. 6
●
High Degree of Flexibility for Installation ........ 7
●
Reduction of Power Consumption .................. 8
●
Realizing More Convenient Operations
●
Using Screen InStyle ...................................... 8
1-2. Controls and Functions ............................... 9
Front ................................................................ 9
●
Rear ................................................................10
●
1-3. Supported Resolutions ...............................11
1-4.
Changing the Computer Display Settings
Windows 10 ....................................................12
●
Windows 8.1 / Windows 7 ..............................12
●
macOS ...........................................................12
●
Chapter 2 Basic Adjustment / Setting ............ 13
2-1. Switch Operation Method ...........................13
2-2. Switching Input Signals ..............................14
Switching Display Modes (Color Modes)
2-3.
Display Modes ................................................14
●
2-4. Conserving Energy ...................................... 15
2-5. Adjusting Brightness ..................................16
2-6. Adjusting Volume.........................................16
Chapter 3 Advanced Adjustment / Setting .... 17
3-1. Basic Operation of the Setting Menu ........17
3-2. Setting Menu Functions ..............................18
Color Adjustment ............................................18
●
Signal Settings ...............................................21
●
Preference Settings ...................................... 23
●
Language .......................................................24
●
Information .....................................................24
●
Chapter 4 Administrator Settings ................... 25
4-1. Basic Operation of the “Administrator
Settings” Menu ............................................ 25
4-2. Functions of the “Administrator
Settings” Menu ............................................ 26
...12
...14
Chapter 5 Troubleshooting .............................. 28
5-1. No Picture .................................................... 28
5-2. Imaging Problems ....................................... 29
5-3. Problems Related to DisplayPort Daisy
Chain Connection ....................................... 30
5-4. Other Problems ............................................31
Chapter 6 Reference ........................................ 32
6-1. Removing the Stand ................................... 32
6-2. Attaching the Optional Arm ....................... 33
Attaching the optional arm (or optional
●
stand) ............................................................ 33
Attaching the original stand .......................... 34
●
6-3. Detaching/Attaching the Cable Holder ..... 35
Detaching the cable holder ........................... 35
●
Attaching the cable holder ............................ 35
●
6-4. Detaching / Attaching the Cable Cover .... 36
Attaching the cable cover .............................. 36
●
Detaching the cable cover .............................37
●
6-5. Connecting Multiple PCs ........................... 38
Connection examples ................................... 38
●
6-6. Using the USB Hub Function ..................... 39
Connection procedure................................... 39
●
6-7. Specications ............................................. 40
Accessories ....................................................41
●
Appendix .............................................................. 42
Trademark ............................................................... 42
License .................................................................... 42
CONTENTS
5
Chapter 1 Introduction
Thank you very much for choosing an EIZO color LCD monitor.
1-1. Features
DisplayPort Daisy Chain Connection
●
The monitor comes equipped with an output terminal ( ), as well as a DisplayPort input terminal. By
using the DisplayPort cable to connect (link together) a maximum of four monitors in a daisy chain
connection, the cables can be arranged optimally.
Note
• DisplayPort daisy chain connection is a function supported by DisplayPort Version 1.2. For this reason, it is
necessary to change the version of the DisplayPort on the monitor outputting the DisplayPort signal from
Version 1.1 (the default setting) to Version 1.2 (refer to “DisplayPort” (page 27)).
• In order to use daisy chain connection, the graphics board of the computer must support Multi-Stream
Transport (MST). For details, contact the manufacturer of the computer or the store where you bought the
product.
• The number of monitors it is possible to connect varies depending on the monitors you are using and the
graphics board of the computer. For details, refer to the compatibility information on our company website.
Chapter 1 Introduction
6
High Degree of Flexibility for Installation
●
• This product can be used as an external monitor of a notebook computer.
• By attaching the monitor to an arm, the screen can be rotated 180° (upward-downward rotation)
and used in a multi-monitor conguration.
Note
• In order to rotate the display of the monitor 180°, it is necessary to congure the settings for the computer.
Chapter 1 Introduction
7
Reduction of Power Consumption
●
This product provides a function that automatically adjusts the screen brightness to reduce power
consumption *1. Power Reduction, CO2 Reduction, and Eco Performance Level can be checked on
the "EcoView Settings" menu. (page 15)
• Auto EcoView
The ambient light sensor on the front of the monitor detects the ambient brightness to automatically
adjust the screen brightness to a comfortable level.
• EcoView Optimizer 2
The monitor automatically adjusts the screen brightness according to the white level of the input
signal. This function can reduce power consumption while maintaining the brightness specied by
the input signal.
*1 Reference values
Maximum power consumption: 59 W (when a USB device is connected and the speakers are working),
standard power consumption: 11 W (brightness 120 cd/m
speakers are not working, at default settings)
2
, when no USB device is connected and the
Realizing More Convenient Operations Using Screen InStyle
●
The "Screen InStyle" monitor control utility enables you to use the monitor more conveniently.
• The monitor color mode can be switched automatically to suit the software to be used.
• When multiple monitors are installed, you can turn the power on and off or change the color mode
of all monitors at the same time.
Note
• Screen InStyle can be downloaded from our web site (www.eizoglobal.com).
• The Windows operating systems are only supported.
Chapter 1 Introduction
8
1-2. Controls and Functions
Front
●
5 5
4321
1. Ambient light sensor Detects ambient brightness. If you use Auto EcoView, the screen brightness is
automatically adjusted according to the ambient brightness (page 15).
2. Operation switches Displays menus. Operate the switches according to the operation guide (page 17).
3. Power switch Turns the power on or off.
4. Power indicator Indicates the monitor’s operation status.
White: Normal operation mode
Orange: Power saving mode
OFF: Main power / power off
5. Speakers Outputs audio.
Chapter 1 Introduction
9
Rear
●
6
8
9
7
12
13
16 17 18 914 15
6. Handle This handle is used for transportation.
7. Security lock slot Complies with Kensington’s MicroSaver security system.
8. Lock button Use this button to remove the monitor from the stand.
9. USB downstream
port
10. Headphone jack Connects to headphones.
11. Stereo mini jack If you connect an external device using the stereo mini jack cable, external audio
12. Cable holder Holds the monitor cables.
13. Stand
14. Main power switch
15. Power connector Connects the power cord.
16. Input signal
17. DisplayPort output
18. USB upstream port
*1 An optional arm (or optional stand) can be attached by removing the stand section.
*1
connectors
connector
Connects to a peripheral USB device.
Note
• When connecting (linking together) three or more monitors in a daisy chain
connection using the USB hub function, use the bottom USB downstream port.
can be output from the monitor.
Adjusts the height and angle (tilt and swivel) of the monitor.
Turns the main power on or off.
The following connectors are available on the monitor rear in order of left to right.
DVI connector
HDMI connector
DisplayPort connector
When connecting DisplayPorts in a daisy chain connection, this connects to the
DisplayPort input connectors of the other monitors in the conguration. When
making a connection, it is necessary to change the version of the DisplayPort on
the monitor outputting the DisplayPort signal from Version 1.1 (the default setting)
to Version 1.2 (refer to “DisplayPort” (page 27)).
Connect the USB cable when using software that requires USB connection or when
using the USB hub function.
: On, : Off
10
11
Chapter 1 Introduction
10
1-3. Supported Resolutions
The monitor supports the following resolutions.
Resolution
720 × 400 70.087 √ √ √
640 × 480 59.940 √ √ √
640 × 480 60.000 √ √ -
800 × 600 6 0.317 √ √ √
1024 × 768 60.004 √ √ √
1280 × 800 59.810 √ √ √
1280 × 1024 60.020 √ √ √
1600 × 900 60.000 √ √ √
1600 × 1200 60.000 √ √ √
1680 × 1050 59.954 √ √ √
1680 × 1050 59.883 √ √ √
1920 × 1200 59.950 √ √ √
1920 × 1080 60.000 - √ -
1920 × 1080 59.940 - √ 720 × 480 (4:3) 60.000 √ √ 720 × 480 (4:3) 59.940 √ √ -
720 × 480 (16:9) 60.000 √ √ -
720 × 480 (16:9) 59.940 √ √ 720 (1440) × 480 (4:3) 60.000 - √ 720 (1440) × 480 (4:3) 59.940 - √ -
720 (1440) × 480 (16:9) 60.000 - √ 720 (1440) × 480 (16:9) 59.940 - √ -
720 × 576 (4:3) 50.000 - √ -
720 × 576 (16:9) 50.000 - √ -
720 (1440) × 576 (4:3) 50.000 - √ -
720 (1440) × 576 (16:9) 50.000 - √ -
1280 × 720 60.000 √ √ √
1280 × 720 59.940 √ √ -
1280 × 720 50.000 - √ 1920 × 1080 60.000 √ √ √
1920 × 1080 59.940 √ √ 1920 × 1080 50.000 - √ -
Vertical scan frequency (Hz)
DisplayPort HDMI DVI- D
Chapter 1 Introduction
11
1-4. Changing the Computer Display Settings
If the image is not displayed properly after connecting the monitor to a PC, follow the procedure below to
change the display settings on the computer.
Windows 10
●
1. Right-click the mouse anywhere on the desktop except on icons. A menu is displayed.
2. From the displayed menu, click “Display Settings”. The “Settings” screen is displayed.
3. If multiple monitors, including notebook PC screens, are connected to the computer, select “Extend
these displays” in the “Multiple displays” menu, and then click “Keep changes” on the conrmation
screen. After changing the settings, select a monitor in the “Select and rearrange displays” menu.
4. Select the “Make this my main display” option in the “Multiple displays” menu. This enables the
monitor to display images properly.
5. Conrm that the recommended resolution for the monitor is set in the “Resolution” menu.
(“(Recommended)” is displayed after the resolution.)
6. To change the size of text and icons, select a magnication in the menu of zoom percentages
according to personal preference.
7. If a message prompting you to sign out is displayed after changing the settings, sign out and then
sign in again.
Windows 8.1 / Windows 7
●
* For Windows 8.1, click the "Desktop" tile on the Start Screen to display the desktop.
1. Right-click the mouse anywhere on the desktop except on icons. A menu is displayed.
2. From the displayed menu, click “Screen resolution”. The settings screen is displayed.
3. If multiple monitors, including notebook PC screens, are connected to the computer, select “Extend
these displays” in the “Multiple displays” menu, and then click “Apply”. Click “Keep changes” on
the conrmation screen.
4. Select a monitor in the “Display” menu, and then select the “Make this my main display” option
and click “Apply”. This enables the monitor to display images properly.
5. Conrm that the recommended resolution for the monitor is set in the “Resolution” menu.
(“(recommended)” is displayed after the resolution.)
6. To change the size of text and icons, click “Make text and other items larger or smaller”, select a
size according to personal preference on the settings screen, and then click “Apply”.
7. If a message prompting you to sign out/log off is displayed after changing the settings, sign out/
log off and then sign in/log in again.
macOS
●
1. Select “System Preferences” from the Apple menu.
2. When the “System Preferences” panel is displayed, click “Displays”.
3. If multiple monitors, including notebook PC screens, are connected to the computer, make sure
that “Mirror Displays” is not selected on the “Arrangement” tab. If it is selected, remove the check
mark.
4. Select the “Display” tab, and make sure that “Default for display” is selected for “Resolution”. If
it is not selected, add a check mark. The correct resolution has now been set for your display.
Close the “System Preferences” panel. If multiple monitors, including notebook PC screens, are
connected to the computer, congure these settings in “Display” on each monitor.
5. To select a resolution according to personal preference, select “Scaled” and then select a
resolution (either from a list or icons), and then close the panel.
Chapter 1 Introduction
12
Chapter 2 Basic Adjustment / Setting
This product enables users to change the brightness according to personal preference or to suit the usage
environment, and to reduce power consumption to conserve energy.
This chapter describes the basic functions that can be adjusted and set using the switches on the front of the
monitor.
For advanced adjustment and setting procedures using the Setting menu, see “Chapter 3 Advanced
Adjustment / Setting” (page 17).
2-1. Switch Operation Method
Displaying the operation guide
1.
1. Touch any switch (except ).
The operation guide appears on the screen.
Adjusting / setting
2.
1. Touch a switch for adjustment / setting.
The Adjustment / Setting menu appears.
(A submenu may also be displayed. In this case, select the item for adjustment / setting using
select
2. Perform adjustment / setting with the switches and select to accept the changes.
Exiting
3.
1. Select to exit the menu.
.)
and
Chapter 2 Basic Adjustment / Setting
13
2-2. Switching Input Signals
When a monitor has multiple signal inputs, the signal to display on-screen can be changed.
Note
• "Screen InStyle" allows you to switch input signals using the shortcut keys on the keyboard.
2-3. Switching Display Modes (Color Modes)
This product is preinstalled with color modes for various display purposes.
By switching the mode according to the purpose and contents of the display, you can display images in
an appropriate manner.
Display Modes
●
Color Mode Purpose
User1
User2
sRGB
Paper
Movie
DICOM
Note
• "Screen InStyle" allows you to select the color mode automatically according to the software in use.
• In Paper mode, the amount of blue light emitted from the screen is reduced by changing the color tone and
controlling the brightness.
Select either of these modes to set a user-dened display mode.
This mode is suitable for matching color reproduction with peripheral devices that
support sRGB, such as when printing photos taken using a digital camera.
This mode uses color tones and contrast similar to that of paper to produce a printed
paper effect. It is suitable for displaying images from media such as books and
documents.
This mode displays moving images brightly and with a clear-cut three-dimensional
appearance. It is suitable for playing back video content.
Select this mode to simply display medical purpose digital images based on DICOM®
Part 14.
Attention
• This is not intended to be used for diagnostic purposes.
Chapter 2 Basic Adjustment / Setting
14
2-4. Conserving Energy
This monitor is equipped with EcoView functions to enable users to conserve energy.
You can use this function to curtail unnecessary power consumption and save on electricity expenses.
Saving power also reduces carbon dioxide emissions.
Note
• The power saving level (Power Reduction, CO2 Reduction, and Eco Performance Level) can be checked on the
“EcoView Settings” menu. The more indicators that light up representing the Eco Performance Level, the higher
the power saving level attained.
- Power Reduction: the reduction in the backlight’s power consumption as a result of the adjusted brightness
value.
- CO
Reduction: converted from the “Power Reduction” value, this is an estimate of the quantity of CO2
2
emissions reduced when using the monitor for 1 hour.
• The numeric value is a result of calculation based on a default setting (0.000555t-CO2 / kWh) determined by a
Japanese ministerial ordinance (2006, Ministry of Economy, Trade and Industry, Ministry of Environment, civil
code article 3) and may differ depending on country and year.
Function
Auto EcoView
EcoView Optimizer 2
Setting
Value
On
Off
On
Off
Description
The ambient light sensor on the front of the monitor
detects the ambient brightness to automatically adjust
the screen brightness to a comfortable level using Auto
EcoView. The power consumption of the backlight can
be curtailed by adjusting the brightness to an appropriate
level.
This function can also mitigate eye strain and tiredness
caused by a screen that is too bright or too dark.
Note
• Be careful not to block the ambient light sensor on the
lower side of the monitor when using Auto EcoView.
• Even when Auto EcoView is set to “On”, you can
change the brightness of the monitor using the
operation switches (
in the color adjustment settings. The manner in which
Auto EcoView changes the brightness will also vary
depending on the value you set.
• When “DICOM” is selected for the color mode, the
Auto EcoView setting is turned “Off”.
The monitor automatically adjusts the screen brightness
according to the white level of the input signal.
This function can reduce power consumption while
maintaining the brightness specied by the input signal.
Note
• When “Movie” is selected for the color mode, EcoView
Optimizer 2 is set to “Off”.
• When set to “On”, the appearance of pale colors may
change. If this bothers you, set this function to “Off”.
) on the front of the monitor or
Chapter 2 Basic Adjustment / Setting
15
2-5. Adjusting Brightness
The brightness of the screen can be adjusted to suit the installation environment or personal preference.
The screen brightness is adjusted by changing the brightness of the backlight (light source from the LCD
back panel).
Setting Value
0 to 100
2-6. Adjusting Volume
The volume of the speakers and headphones can be set individually.
Setting Value
0 to 30
When the speakers are
connected
When the headphones are
connected
Chapter 2 Basic Adjustment / Setting
16
Chapter 3 Advanced Adjustment / Setting
This chapter describes the advanced monitor adjustment and setting procedures using the Setting menu.
For basic functions, see “Chapter 2 Basic Adjustment / Setting” (page 13).
3-1. Basic Operation of the Setting Menu
Menu display
1.
1. Touch any switch (except ).
The operation guide appears.
2. Select .
The Setting menu appears.
Adjusting / setting
2.
1. Select a menu to adjust / set with and select .
The Sub menu appears.
2. Select an item to adjust / set with and select .
The Adjustment / Setting menu appears.
3. Perform adjustment / setting with or and select to accept the changes.
The Sub menu appears.
Selecting
making changes.
Exiting
3.
1. Selecting several times will terminate the Setting menu.
during adjustment / setting will cancel the adjustment / setting and restore the state prior to
Chapter 3 Advanced Adjustment / Setting
17
3-2. Setting Menu Functions
Color Adjustment
●
The color mode settings can be adjusted according to personal preference.
Functions that can be adjusted differ depending on the color mode.
Function
Brightness
Contrast
Temperature
Gamma
Advanced
Settings
Reset
Overdrive
Hue
Saturation
Gain
User1
User2
√ √ √ √
√
√
√
√
√
√
√
√ √ √ √
√: Adjustable -: Not adjustable
Color Mode
sRGB Paper Movie DICOM
-
- -
-
- - - -
- - - -
- -
- -
- - - -
√ √
√
√
√
-
-
-
-
-
Attention
• It takes about 30 minutes for the monitor display to stabilize. Please wait 30 minutes or more after power to
the monitor has been turned on before adjusting the monitor.
• The same image may be observed in different colors on multiple monitors due to monitor-specic
characteristics. Make ne color adjustments visually when matching colors across multiple monitors.
Chapter 3 Advanced Adjustment / Setting
18
Function
Color Mode User1
Brightness 0 to 100
Contrast 0 to 100
Temperature Off
Gamma 1.8
Setting
Value
User2
sRGB
Paper
Movie
DICOM
4000 K to
10000 K
increments of
500 K. 9300 K
is included.)
2.0
2.2
2.4
Description
Select the desired mode according to the monitor application.
The color mode settings can also be adjusted according to personal
preference. Select the mode for adjustment and perform adjustment
using the relevant functions.
Note
• For details on the adjustment status of each mode, see “2-3.
Switching Display Modes (Color Modes)” (page 14).
The screen brightness is adjusted by changing the brightness of the
backlight (light source from the LCD back panel).
Note
• If the image is too dark even when the brightness is set to 100,
adjust the contrast.
The brightness of the screen is adjusted by varying the video signal
level.
Note
• A contrast of 50 displays every color gradation.
• When adjusting the monitor, it is recommended to perform
brightness adjustment, which does not lose gradation
characteristics, prior to contrast adjustment.
• Perform contrast adjustment in the following cases.
- If the image is too dark even when the brightness is set to 100
(Set the contrast to higher than 50.)
Adjust the color temperature.
The color temperature is normally used to express the hue of “White”
and/or “Black” with a numerical value. The value is expressed in
(in
degrees “K” (Kelvin).
The screen becomes reddish at low color temperatures and bluish at
high color temperatures, similar to the temperatures of a ame. A gain
preset value is set for each color temperature setting value.
Note
• The value shown in “K” is available only as a reference.
• “Gain” allows you to perform more advanced adjustment.
• If set to “Off”, the image is displayed in the preset color of the
monitor (Gain: 100 for each RGB channel).
• When the gain is changed, the color temperature setting changes
to “Off”.
Adjust the gamma.
While the brightness of the monitor varies depending on the input
signal, the variation rate is not proportional to the input signal.
Maintaining the balance between the input signal and brightness of
the monitor is referred to as “Gamma correction”.
Note
• If "sRGB" is selected for the color mode, the gamma value is
xed to "sRGB".
• If “Paper” is selected for the color mode, “Paper” is displayed for
the gamma value.
• If “DICOM” is selected for the color mode, “DICOM” is displayed
for the gamma value.
Chapter 3 Advanced Adjustment / Setting
19
Function
Advanced
Settings
Reset - Reset any color adjustments for the currently selected color mode
Overdrive Enhanced
Hue -50 to 50
Saturation
Gain 0 to 100
Setting
Value
This function allows you to set the overdrive intensity based on the
Standard
Off
-50 to 50 Adjust the color saturation.
use of the monitor.
Image lag can be reduced by using the “Enhanced” setting when
displaying moving images.
Note
• Depending on the resolution of the input signal and the setting of
“Picture Expansion” (from the “Signal” menu), overdrive may be
set to “Off”.
Adjust the hue.
Note
• Using this function may prevent some color gradations from being
able to be displayed.
Note
• Using this function may prevent some color gradations from being
able to be displayed.
• The minimum value (-50) changes the screen to monochrome.
The brightness of each red, green, and blue color component is
referred to as “Gain”. The hue of “white” can be changed by adjusting
the gain.
Note
• Using this function may prevent some color gradations from being
able to be displayed.
• The gain value changes according to the color temperature.
• When the gain is changed, the color temperature setting changes
to “Off”.
back to the default settings.
Description
Chapter 3 Advanced Adjustment / Setting
20
Signal Settings
●
Set the details regarding input signal, such as the screen display size and color format.
Function Setting Value Description
Picture Expansion Auto
*1
Full Screen
Aspect Ratio
Dot by Dot
The screen size of the monitor display can be changed.
• “Auto”
The monitor automatically changes the screen size
according to the aspect ratio and resolution information
from the PC.
• “Full Screen”
Images are stretched to full screen. Since aspect ratios are
not maintained, images may be distorted in some cases.
• “Aspect Ratio”
Images are enlarged to full screen without changing the
aspect ratio. Since aspect ratios are maintained, blank
horizontal or vertical borders may appear.
• “Dot by Dot”
Displays the image at the set resolution or size specied by
the input signal.
Note
• Example settings
- Full Screen
- Aspect Ratio
- Dot by Dot
(input signal)
Sharpness -2 to 2 When a low resolution image is displayed using picture
expansion mode (“Full Screen” or “Aspect Ratio”), the text and
lines of the image may appear blurry. This blurriness can be
reduced by conguring the settings for sharpness.
Note
• For some resolutions, it is not necessary to congure the
settings for sharpness. (“Sharpness” is not a value that can
be selected.)
Chapter 3 Advanced Adjustment / Setting
21
Function Setting Value Description
Input Color Format Auto
YUV 4:2:2
YUV 4:4:4
YUV
*1
*1
*2
RGB
Input Range Auto
Full
Limited
Sound Source Stereo Mini Jack
DisplayPort
HDMI
*2
*3
*1 Only enabled during HDMI input
*2 Only valid for DisplayPort input
*3 Only valid for HDMI (video signal) input
The color format of the input signal can be specied.
Try changing this setting if colors are not displayed correctly.
Note
• This setting is required when a DVI device is connected to
the monitor via the HDMI connector port using a DVI-HDMI
conversion connector.
• For DVI signal input, the setting is automatically set to
“RGB”.
Depending on the PC, black and white of the video level of the
signal output to the monitor may be limited. If a limited signal is
displayed on the monitor, black will appear faint and white will
appear dull, leading to a reduction in contrast. The output range
of such signals can be extended to match the actual contrast
ratio of the monitor.
• “Auto”
Automatically identies the brightness range of the input
signal and displays the image accordingly.
• “Full”
Extension of the signal output range is not performed.
• “Limited”
Extends the signal output range through 0 to 255 and
displays the image.
Note
• For DVI signal input, the setting is automatically set to “Full”.
• When “YUV” is selected in “Input Color Format”, the setting
is automatically set to “Limited”. Additionally, when “Auto” is
selected and the monitor determines the input color format
to be YUV, the setting is automatically set to “Limited”.
For DisplayPort signal input and HDMI signal input, the sound
source can be changed.
Note
• For DVI signal input and HDMI (PC signal) input, the setting
is automatically set to “Stereo Mini Jack”.
Chapter 3 Advanced Adjustment / Setting
22
Preference Settings
●
The monitor’s settings can be congured to suit the usage environment or personal preference.
Function
Menu Rotation 0°
Power Save On
Power Indicator On
Monitor Reset - Restore all settings to their default values except for the following settings.
Setting
Value
90°
270°
Off
Off
Description
When the monitor is used in a vertical position, the direction of the Setting
menu can also be changed.
Note
• Check whether the cables are connected properly.
• It is necessary to congure the settings of the computer to use the
monitor vertically. For details, refer to our website (www.eizoglobal.com).
• The menu cannot be rotated 180°. When rotating a monitor 180°, perform
the adjustments / settings for the monitor before rotating it.
The monitor can be set to enter power saving mode according to the state of
the PC.
The monitor changes to power saving mode about 15 seconds after signal
input ceases to be detected.
When the monitor has shifted to power saving mode, images are not
displayed on the screen.
• How to exit power saving mode
- Press the operation switches (excluding
- The monitor automatically exits power saving mode when the monitor
receives input
Note
• At the time of shifting to power saving mode, a message that indicates
the transition is displayed 5 seconds in advance.
• When not using the monitor, you can turn off the main power supply or
disconnect the power plug so that the power is cut completely.
• When the monitor is in power saving mode, devices connected to the
USB downstream port will still work. Therefore, power consumption of
the monitor varies with connected devices even in power saving mode.
• The amount of power consumption also varies while the stereo mini jack
cable is connected.
The power indicator (white) can be turned off in normal operation mode.
• Settings on the “Administrator Settings” menu
) on the front of the monitor
Chapter 3 Advanced Adjustment / Setting
23
Language
●
The display language for menus and messages can be selected.
Setting Value
English, German, French, Spanish, Italian, Swedish, Japanese, Simplied Chinese, Traditional
Chinese
Attention
• The display language of the “Administrator Settings” menu cannot be changed.
Information
●
Monitor information (product name, serial number, usage time, resolution, and input signal) can be
checked.
Example:
Chapter 3 Advanced Adjustment / Setting
24
Chapter 4 Administrator Settings
This chapter describes how to congure monitor operation using the “Administrator Settings” menu.
4-1. Basic Operation of the “Administrator Settings”
Menu
Menu display
1.
1. Touch to turn off the monitor.
2. While touching the leftmost switch, touch
The “Administrator Settings” menu appears.
for more than 2 seconds to turn on the monitor.
Setting
2.
1. Select an item to set with and select .
The Adjustment / Setting menu appears.
2. Set with and select .
The “Administrator Settings” menu appears.
Applying and exiting
3.
1. Select “Apply” and then .
The settings are applied and the “Administrator Settings” menu exits.
Attention
• The language (English) of the “Administrator Settings” menu cannot be changed.
Chapter 4 Administrator Settings
25
4-2. Functions of the “Administrator Settings” Menu
Function Setting Value Description
Auto Input Detection On
Off
Compatibility Mode On
Off
This function automatically recognizes the connector through
which PC signals are input, and displays images on the
screen accordingly.
• “On”
When the monitor is connected to multiple PCs, if a
specic PC enters power saving mode or no signals
are input to the monitor, the connector is automatically
changed to another one to which signals are input.
• “Off”
This function displays the signal from the selected
connector regardless of whether a signal is input or not.
In this case, you can select the input signal to display
using the
For details, see “2-2. Switching Input Signals” (page
14).
Note
• When “Version 1.2” is selected for “DisplayPort” in the
“Administrator Settings” menu, the setting for “Auto Input
Detection” is automatically set to “Off”.
• This product automatically recognizes the connector
through which PC signals are input, and displays images
on the screen accordingly regardless of whether this
function is set to On or Off just after the main power
switch on the rear side of the monitor has been turned on.
However, this does not include the case when “Version
1.2” is selected for “DisplayPort” in the “Administrator
Settings” menu.
• When this function is set to “On”, the monitor only enters
the power saving mode when signals are not input from
any PC.
If you want to avoid the following phenomena, set this function
to "On".
• The positions of windows and icons are shifted when the
monitor is turned off / on or has returned from the power
saving mode.
• Power Save function of the PC does not work normally.
• When the power to the monitor is turned off, a device
connected to the USB downstream port does not work.
Note
• When “Version 1.2” is selected for “DisplayPort” in
the “Administrator Settings” menu, the setting for
“Compatibility Mode” is automatically set to “On”.
operation switch on the front of the monitor.
Chapter 4 Administrator Settings
26
Function Setting Value Description
DisplayPort Version 1.1
Version 1.2
On-Screen Logo On
Off
Key Lock Off
Menu
All
The types of signals that the monitor can display can be
changed.
Attention
• When connecting monitors in a DisplayPort daisy
chain connection, select “Version 1.2” for the monitors
outputting DisplayPort signals.
• When connecting to a DisplayPort connector, the screen
may not be displayed properly because the DisplayPort
version of the computer is different from that of the
monitor. If this problem occurs, try conguring the version
setting.
When the monitor is turned on, the EIZO logo appears on the
screen.
When this function is set to “Off”, the EIZO logo does not
appear.
In order to prevent changes to settings, the operation
switches on the front of the monitor can be locked.
• “Off” (default setting)
Enables all switches.
• “Menu”
Locks the
• “All”
Locks all switches except the power switch.
switch.
Chapter 4 Administrator Settings
27
Chapter 5 Troubleshooting
5-1. No Picture
Problem Possible cause and remedy
1. No picture
• Power indicator does not light up.
• Power indicator is lighting white. • Increase “Brightness”, “Contrast”, or “Gain” in the Setting menu (see
• Power indicator is lighting orange. • Switch the input signal.
• Power indicator is ashing orange
and white.
2. The message below appears. This message appears when the signal is not input correctly even
• This message appears when no
signal is input.
Example:
• The message shows that the
input signal is out of the specied
frequency range.
Example:
• Check whether the power cord is connected properly.
• Turn on the main power switch on the rear side of the monitor.
• Tou c h
• Turn off the main power switch on the rear side of the monitor, and
then turn it on again a few minutes later.
“Color Adjustment” (page 18)).
• Turn the setting “On” for “Compatibility Mode” on the “Administrator
Settings” menu (see “Compatibility Mode” (page 26)).
• Move the mouse or press any key on the keyboard.
• Check whether the PC is turned on.
• Turn off the main power switch on the rear side of the monitor, and
then turn it on again.
• This symptom may occur during DisplayPort input. Use a signal
cable recommended by us for the connection. Turn the monitor off
and on.
though the monitor is functioning properly.
• The message shown left may appear, because some PCs do not
output the signal immediately after power-on.
• Check whether the PC is turned on.
• Check whether the signal cable is connected properly.
• Switch the input signal.
• Turn off the main power switch on the rear side of the monitor, and
then turn it on again.
• Check whether the PC is congured to meet the resolution and
vertical scan frequency requirements of the monitor (see “1-3.
Supported Resolutions” (page 11)).
• Reboot the PC.
• Select an appropriate setting using the graphics board’s utility. Refer
to the User’s Manual of the graphics board for details.
.
Chapter 5 Troubleshooting
28
5-2. Imaging Problems
Problem Possible cause and remedy
1. The screen is too bright or too
dark.
2. Brightness cannot be changed or
it changes on its own.
3. Text is blurred. • Check whether the PC is congured to meet the resolution and
4. Afterimages appear. • Afterimages are particular to LCD monitors. Avoid displaying the
5. Green / red / blue / white / dark
dots remain on the screen.
6. Interference patterns or pressure
marks remain on the screen.
7. Noise appears on the screen. • In the Setting menu, set “Overdrive” to “Off” (see “Overdrive” (page
8. The positions of windows and
icons are shifted when the
monitor is turned off / on or when
restored from power saving
mode.
9. The color shown on the screen is
not correct.
10. Images are not displayed over the
entire area of the screen.
• Use “Brightness” or “Contrast” in the Setting menu to adjust it (see
“Color Adjustment” (page 18)). (The LCD monitor backlight has
a limited life span. If the screen becomes dark or begins to icker,
contact your local EIZO representative.)
• If the screen is too bright, try changing the Auto EcoView setting
to “On”. The monitor detects the ambient brightness to adjust the
screen brightness automatically (see “Auto EcoView” (page 15)).
• Try changing the Auto EcoView setting to “Off” (see “Auto EcoView”
(page 15)).
vertical scan frequency requirements of the monitor (see “1-3.
Supported Resolutions” (page 11)).
same image for a long time.
• Use the screen saver or power saving function to avoid displaying
the same image for extended periods of time. Depending on the
image, an afterimage may appear even if it was displayed for a short
period of time. To remove such a phenomenon, change the image
or keep the power turned off for several hours.
• This is due to LCD panel characteristics and not a malfunction.
• Leave the monitor with a white or black screen. The symptom may
disappear.
20)).
• When inputting HDCP system signals, normal images may not be
displayed immediately.
• Turn the setting “On” for “Compatibility Mode” on the “Administrator
Settings” menu (see “Compatibility Mode” (page 26)).
• Try changing “Input Color Format” in the Setting menu (see “Input
Color Format” (page 22)).
• Try changing “Picture Expansion” in the Setting menu (see “Picture
Expansion” (page 21)).
Chapter 5 Troubleshooting
29
5-3. Problems Related to DisplayPort Daisy Chain
Connection
Problem Possible cause and remedy
1. The screen is not displayed. • For each monitor connected in the DisplayPort daisy chain
connection, conrm the following.
- Check whether “DisplayPort” is selected for the input signal.
- For monitors outputting the DisplayPort signal, check whether
“Version 1.2” is selected for “DisplayPort” in the “Administrator
Settings” menu (refer to “DisplayPort” (page 27)).
• Check whether the signal cable is properly connected. When
inputting the signal for DisplayPort, connect to
outputting signals in a daisy chain connection.
• In order to use daisy chain connection, the graphics board of the
computer must support Multi-Stream Transport (MST). For details,
contact the manufacturer of the computer or the store where you
purchased the product.
• When using a daisy chain connection with a notebook PC, the
screen of the notebook PC may be counted as one monitor.
• The number of monitors it is possible to connect varies depending
on the monitors you are using and the graphics board of the
computer. For details, refer to the compatibility information on our
company website.
• Depending on the resolution of the monitor being connected,
the screen may not be displayed due to insufcient bandwidth.
For details, refer to the compatibility information on our company
website.
. is used when
Chapter 5 Troubleshooting
30
5-4. Other Problems
Problem Possible cause and remedy
1. The Setting menu does not
appear.
2. Cannot select items in the Setting
menu.
3. No audio output. • Check whether the stereo mini jack cable is properly connected to
4. USB devices connected to the
monitor do not work.
5. The USB hub function cannot be
used.
6. Powerindicatorisashing
orange and white.
7. Power Save function of the PC
does not work normally.
• Check whether the switch operation lock function is active (see “Key
Lock” (page 27)).
• Items that are displayed with gray text cannot be changed.
the stereo mini jack (
• Check whether volume is set to 0.
• Check the PC and audio playback software to see whether they are
congured correctly.
• For DisplayPort input and HDMI input, check the settings for “Sound
Source” (refer to “Sound Source” (page 22)).
• Check whether the USB cable is correctly connected between the
PC and the monitor (see “6-6. Using the USB Hub Function” (page
39)).
• Check whether the USB cable is correctly connected between the
peripheral and the monitor.
• Try using a different USB port on the monitor.
• Try using a different USB port on the PC.
• Reboot the PC.
• When “Compatibility Mode” is set to “Off” in the “Administrator
Settings” menu and the power of the monitor is turned off, devices
connected to the USB downstream port are not operational. Change
the setting for “Compatibility Mode” to “On” (refer to “Compatibility
Mode” (page 26)).
• If the peripheral devices work correctly when they are directly
connected to the PC, contact your local EIZO representative.
• Depending on the USB 3.1 host controller that you are using,
connected USB devices may not be recognized correctly. Update to
the latest USB 3.1 driver provided by each manufacturer, or connect
the monitor to the USB 2.0 port.
• Check the PC’s BIOS setting for USB when using Windows. (Refer
to the manual of the PC for details.)
• When “Compatibility Mode” is set to “Off” in the “Administrator
Settings” menu and the power of the monitor is turned off, the USB
hub function cannot be used. Change the setting for “Compatibility
Mode” to “On” (refer to “Compatibility Mode” (page 26)).
• When connecting (linking together) three or more monitors in a
daisy chain connection using the USB hub function, use the bottom
USB downstream port.
• This symptom may occur when the PC is connected to the
DisplayPort connector. Use a signal cable recommended by us for
the connection. Turn the monitor off and on.
• Check the connection and condition of the USB devices connected
to the monitor.
• Turn off the main power switch on the rear side of the monitor, and
then turn it on again.
• Turn the setting “On” for “Compatibility Mode” on the “Administrator
Settings” menu (see “Compatibility Mode” (page 26)).
).
Chapter 5 Troubleshooting
31
Chapter 6 Reference
6-1. Removing the Stand
The stand section of this product can be removed.
Attention
• Do not move the stand up and down after removing it. If you move the stand up and down while it is not attached
to the monitor, this may cause damage or injury.
• The monitor and the stand are heavy. If you drop the monitor or stand, this may cause damage or injury.
LaytheLCDmonitoronasoftclothspreadoverastableandatsurfacewith
1.
the panel surface facing down.
Remove the stand.
2.
As shown in the diagram, press the lock button (1) while holding rmly onto the support section of
the stand, and slide the stand in the direction of the pedestal on the bottom (2). Next, pull the stand
upwards to remove it (3).
(3)
(1)
(2)
Chapter 6 Reference
32
6-2. Attaching the Optional Arm
An optional arm (or an optional stand) can be attached by removing the stand section. Please refer to our
web site for the supported optional arm (or optional stand). www.eizoglobal.com
Attention
• When attaching an arm or stand, follow the instructions of the respective User’s Manual.
• When using another manufacturer’s arm or stand, conrm the following in advance and select one conforming to
the VESA standard. Use the VESA mounting screws supplied with this product when attaching the arm or stand.
- Clearance between screw holes: 100 mm × 100 mm
- VESA mount of the arm or stand, external dimensions: 122 mm x 122 mm or less
- Plate thickness: 2.6 mm
- Strong enough to support weight of the monitor unit (excluding the stand) and attachments such as cables.
• When attaching an arm or stand, the installable orientations and movement range (tilt angle) are as follows:
Orientation
*1
Movement range
(tilt angle)
Up: 45˚ Down: 45˚
*1 If you position the monitor facing in this direction, clean the power connector and the surrounding area
regularly. If dust, water, oil, or other materials adhere to the device, it can cause a re.
• Connect the cables after attaching an arm or stand.
• Do not move the removed stand up and down. Doing so may result in injury or device damage.
• The monitor, arm, and stand are heavy. Dropping them may result in injury or equipment damage.
Attaching the optional arm (or optional stand)
●
1. Attach the arm or stand to the monitor.
Use the VESA mounting screws supplied with this product when attaching the arm or stand.
Chapter 6 Reference
33
Attaching the original stand
●
1. Lay the LCD monitor on a soft cloth spread over a stable and at surface with the panel surface
facing down.
2. Remove the xing screws on the optional arm (or optional stand), and detach the optional arm (or
optional stand).
3. Attach the original stand.
Insert the four tabs on the stand into the four holes on the back panel (1), and slide the stand towards the
upper portion of the monitor (2). The stand clicks when it is attached correctly.
(1)
(2)
Click!
Chapter 6 Reference
34
6-3. Detaching/Attaching the Cable Holder
Detaching the cable holder
●
1. Slide the cable holder to the left, and detach it from the stand.
Attaching the cable holder
●
1. Align the tabs of the cable holder with the attachment parts of the stand.
2. Slide the cable holder to the right, and attach it to the stand.
Chapter 6 Reference
35
6-4. Detaching / Attaching the Cable Cover
Attaching the cable cover
●
A B
1. Align the tabs of (A) with the attachment parts of the stand.
A
2. Slide (A) downward to secure the tabs to the attachment parts of the stand.
3. Check the tabs of (B) (four locations indicated by ) and the attachment locations of (A).
A
B
Chapter 6 Reference
36
4. Pass the cables between (A) and (B), and align (B) with (A) to t in.
5. Slide (B) downward and secure it to (A).
Detaching the cable cover
●
1. Slide (B) upward, and detach it from (A).
2. While holding down of (A) lightly, slide (A) upward to detach it from the stand.
Chapter 6 Reference
37
6-5. Connecting Multiple PCs
This product can be connected to multiple PCs and allows you to switch between the connections for
display.
Connection examples
●
DVI-D
HDMI HDMI
DisplayPort
Note
• You can select the input signal to display using the operation switch on the front of the monitor. For details, see
“2-2. Switching Input Signals” (page 14).
• This product provides a function that automatically recognizes the connector through which PC signals are input,
and displays images on the screen accordingly. For details, see “Auto Input Detection” (page 26).
DD200
DVI-D cable (DVI-D - DVI-D)
(Separately sold accessory)
HH200HS
HDMI cable (HDMI - HDMI)
(Separately sold accessory)
PP200
DisplayPort cable (DisplayPort - DisplayPort)
(Included)
DVI-D
DisplayPort
Chapter 6 Reference
38
6-6. Using the USB Hub Function
This monitor is equipped with a USB hub. It functions as a USB hub when connected to a USBcompatible PC, allowing the connection of peripheral USB devices.
Connection procedure
●
1. Connect the USB downstream port of the computer and the USB upstream port of the monitor
with a USB cable.
USB upstream
port
2. Connect a peripheral USB device to the USB downstream port of the monitor
Attention
• This function may not work depending on the computer you are using, your OS and your peripheral devices.
Contact the manufacturer of each device for information about USB compatibility.
• When connecting (linking together) three or more monitors in a daisy chain connection using the USB hub
function, use the bottom USB downstream port.
• Even when the monitor is in power saving mode, devices connected to the USB downstream port are operational.
Due to this, the power consumption of the monitor varies depending on the connected devices, even in power
saving mode.
• When the main power of the monitor is off, a device connected to the USB downstream port will not operate.
• When “Compatibility Mode” (page 26) is set to "Off" and the power to the monitor is turned off, a device
connected to the USB downstream port will not work.
Note
• This product supports USB 3.1*1. When connecting to peripheral devices that support USB 3.1, high-speed data
communication is possible (only if the USB cable connecting the external device or peripheral device supports
USB 3.1).
*1 Only Gen1 5 Gbps is supported.
UU200SS
USB cable (USB Type-B - USB Type-A)
(Included)
USB
downstream port
.
Chapter 6 Reference
39
6 -7. Specications
LCD Panel Ty p e IPS (Anti-Glare)
Backlight LED
Size 61.1 cm (24.1 inch)
Resolution 1920 dots × 1200 lines
Display Size (H × V) 518.4 mm × 324.0 mm
Pixel Pitch 0.270 mm
Display Colors 8-bit colors: 16.77 million colors
Viewing Angle
(H / V, typical)
Response Time (typical) Gray-to-gray: 14 ms (overdrive setting: Off)
Video Signals Input Terminals DisplayPort (HDCP) × 1, HDMI (HDCP)*1 × 1, DVI-D (HDCP) × 1
Output Terminal DisplayPort (HDCP) × 1
Digital Scanning
Frequency
(H / V)
Frame Synchronization
Mode
Max. Dot Clock 162 MHz
USB Port Upstream × 1
Standard USB Specication Rev.3.1Gen1
Communication Speed 5 Gbps (super), 480 Mbps (high), 12 Mbps (full), 1.5 Mbps (low)
Supply Current
Audio Audio Input Format DisplayPort: 2ch linear PCM (32 kHz / 44.1 kHz /
Speakers 1 W + 1 W
Headphones 2 mW + +2 mW (32 Ω)
Input Terminals Stereo mini jack × 1
Output Terminals Headphone jack × 1
Power Input 100 - 240 VAC ±10 %, 50 / 60 Hz 1.00 A - 0.55 A
Maximum Power
Consumption
Power Save Mode 0.5 W or less (no USB device connected, default settings)
Standby Mode 0.5 W or less (no USB device connected, default settings)
178˚ / 178˚
5 ms (overdrive setting: Enhanced)
DisplayPort: 31 kHz to 76 kHz /
59 Hz to 61 Hz,
69 Hz to 71 Hz (at 720 × 400)
HDMI: 15 kHz to 76 kHz /
49 Hz to 61 Hz,
69 Hz to 71 Hz (at 720 × 400)
DVI-D: 31 kHz to 76 kHz /
59 Hz to 61 Hz,
69 Hz to 71 Hz (at 720 × 400)
49.5 Hz to 61.0 Hz
Downstream × 4
Downstream Max. 900 mA / 1 port
48 kHz / 88.2 kHz / 96 kHz / 176.4 kHz /
192 kHz)
HDMI: 2ch linear PCM (32 kHz / 44.1 kHz /
48 kHz/ 88.2 kHz / 96 kHz / 176.4 kHz /
192 kHz)
DisplayPort × 1, HDMI × 1 (each shared with video signal)
59 W or less
Chapter 6 Reference
40
Physical
Specications
Operating
Environmental
Requirements
Transportation /
Storage
Environmental
Requirements
*1 HDMI CEC (or mutual control) is not supported.
Dimensions 531 mm × 338.5 mm to 518.5 mm × 209.3 mm to 240.5 mm
(W × H × D) (Tilt: 35˚)
531 mm × 353.3 mm to 510.1 mm × 190 mm
(W × H × D) (Tilt: 0˚)
Dimensions
(Without Stand)
Net Weight Approx. 5.8 kg
Net Weight (Without
Stand)
Height Adjustment
Range
Tilt Up 35˚, down 5˚
Swivel 344˚
Vertical Rotation Left 90˚, right 90˚
Temperature 5 ˚C to 35 ˚C
Humidity 20 % to 80 % R.H. (no condensation)
Air Pressure 540 hPa to 1060 hPa
Temperature -20 ˚C to 60 ˚C
Humidity 10 % to 90 % R.H. (no condensation)
Air Pressure 200 hPa to 1060 hPa
531 mm × 343.8 mm × 45.5 mm (W × H × D)
Approx. 3.8 kg
180 mm (Tilt: 35˚) / 156.8 mm (Tilt: 0˚)
Accessories
●
For the latest information about accessories, refer to our web site www.eizoglobal.com.
Chapter 6 Reference
41
Appendix
Trademark
The terms HDMI and HDMI High-Denition Multimedia Interface, and the HDMI Logo are trademarks or
registered trademarks of HDMI Licensing, LLC in the United States and other countries.
The DisplayPort Compliance Logo and VESA are registered trademarks of the Video Electronics
Standards Association.
The SuperSpeed USB Trident Logo is a registered trademark of USB Implementers
Forum, Inc.
The USB Power Delivery Trident Logos are trademarks of USB Implementers Forum,
Inc.
DICOM is the registered trademark of the National Electrical Manufacturers Association for its standards
publications relating to digital communications of medical information.
Kensington and Microsaver are registered trademarks of ACCO Brands Corporation.
Thunderbolt is a trademark of Intel Corporation in the United States and/or other countries.
Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and
other countries.
Adobe is a registered trademark of Adobe Systems Incorporated in the United States and other
countries.
Apple, macOS, Mac OS, OS X, Macintosh and ColorSync are registered trademarks of Apple Inc.
EIZO, the EIZO Logo, ColorEdge, CuratOR, DuraVision, FlexScan, FORIS, RadiCS, RadiForce,
RadiNET, Raptor and ScreenManager are registered trademarks of EIZO Corporation in Japan and other
countries.
ColorEdge Tablet Controller, ColorNavigator, EcoView NET, EIZO EasyPIX, EIZO Monitor Congurator,
EIZO ScreenSlicer, G-Ignition, i•Sound, Quick Color Match, RadiLight, Re/Vue, SafeGuard, Screen
Administrator, Screen InStyle, ScreenCleaner and UniColor Pro are trademarks of EIZO Corporation.
All other company and product names are trademarks or registered trademarks of their respective
owners.
License
The bitmap font used for this product is designed by Ricoh Industrial Solutions Inc.
Appendix
42
03V27590A1
UM-EV2457
Copyright © 2018 EIZO Corporation. All rights reserved.
1st Edition-November, 2018
Loading...