Page 1
GB
Original operating instructions
Angle grinder
TE-AG 180
7
Anl_TE_AG_230_SPK1.indb 1 07.09.12 13:59
31011 :.rN-.I 57.803.44 :.rN-.trA
Page 2
1
71
2
4
6
2
5
2
A
C
B
3
- 2 -
Anl_TE_AG_230_SPK1.indb 2Anl_TE_AG_230_SPK1.indb 2 07.09.12 13:5907.09.12 13:59
Page 3
3 4
4a
2 .
1.
5
2.
1.
7
7 8
a
2
6
5
Anl_TE_AG_230_SPK1.indb 3 07.09.12 13:59
a
b
- 3 -
Page 4
9 10
a
b
11 12
a
b
Anl_TE_AG_230_SPK1.indb 4Anl_TE_AG_230_SPK1.indb 4 07.09.12 13:5907.09.12 13:59
- 4 -
Page 5
GB
Table of contents
1. Safety information
2. Layout and items supplied (Figure 1)
3. Proper use
4. Technical data
5. Before starting the equipment
6. Operation
7. Replacing the power cable
8. Cleaning, maintenance and ordering of spare parts
9. Disposal and recycling
10. Storage
Anl_TE_AG_230_SPK1.indb 17 07.09.12 13:59
- 5 -
Page 6
GB
”yriuqni fo ksir eht ecuder ot snoitcurtsni gnitarepo eht daeR - noituaC“
Wear ear-muff s.
The impact of noise can cause damage to hearing.
Wear a breathing mask.
Dust which is injurious to health can be generated when working on wood and other materials. Never
use the device to work on any materials containing asbestos!
Wear safety goggles.
Sparks generated during working or splinters, chips and dust emitted by the device can cause loss of
sight.
This safety guard is designed for sanding/grinding.
This safety guard is designed for cutting and grinding/sanding.
(not included in items supplied)
- 6 -
Anl_TE_AG_230_SPK1.indb 18 07.09.12 13:59
Page 7
GB
Important!
must be observed to avoid injuries and damage.
Please read the complete operating manual with
due care. Keep this manual in a safe place, so
that the information is available at all times. If
you give the equipment to any other person, give
them these operating instructions as well.
We accept no liability for damage or accidents
which arise due to non-observance of these instructions and the safety information.
1. Safety information
Please refer to the booklet included in delivery for
the safety instructions.
Warning!
Read all safety regulations and all instructions.
Failure to follow the warnings and instructions may
result in electric shock, fire and/ or serious injury.
Save all warnings and instructions for future
reference.
2. Layout and items supplied
(Figure 1)
2.1 Layout
1. Spindle lock
2. ON/OFF switch
3. Additional handle
4. Guard
5. Flange nut wrench
6. Handle
2.2 Items supplied
Please check that the article is complete as specifi ed in the scope of delivery. If parts are missing,
please contact our service center or the nearest
branch of the DIY store where you made your
purchase at the latest within 5 work days after
purchasing the article and upon presentation of
a valid bill of purchase. Also, refer to the warranty
table in the warranty provisions at the end of the
operating instructions.
•
ment with care.
•
packaging and/or transportation braces (if
available).
nottub gnikcoL .7
-piuqe eht tuo ekat dna gnigakcap eht nepO
yna dna lairetam gnigakcap eht evomeR
•
snoituacerp ytefas wef a ,tnempiuqe gnisu nehW
Inspect the equipment and accessories for
transport damage.
•
the end of the guarantee period.
Important!
The equipment and packaging material are
not toys. Do not let children play with plastic
bags, foils or small parts. There is a danger of
swallowing or suff ocating!
Original operating instructions
•
•
3. Proper use
The angle grinder is designed for grinding metal
and stone when using the appropriate grinding
wheel and guard.
Caution! To cut metal and stone the grinder/sander may only be used when the guard (available
as an accessory) is mounted.
The machine is to be used only for its prescribed
purpose. Any other use is deemed to be a case
of misuse. The user / operator and not the manufacturer will be liable for any damage or injuries of
any kind caused as a result of this.
Please note that our equipment has not been designed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
4. Technical data
Mains voltage: ............................... 240 V ~ 50 Hz
Power input: ............................................ 2350 W
Idling speed: ......................................... 8000 rpm
Max. wheel diameter: ............................. 180 mm
Mounting spindle thread: .............................. M14
Protection class: ...........................................II /
Weight: .......................................................6.1 kg
snoitcurtsni ytefaS
.deilppus era smeti lla fi ees ot kcehC
litnu gnigakcap eht peek esaelp ,elbissop fI
Anl_TE_AG_230_SPK1.indb 19 07.09.12 13:59
- 7 -
Page 8
GB
Sound and vibration
Sound and vibration values were measured in
accordance with EN 60745.
LpA sound pressure level ................... 92,4 dB(A)
KpA uncertainty ...........................................3 dB
LWA sound power level ................... 103,4 dB(A)
KWA uncertainty .......................................... 3 dB
Wear ear-muff s.
The impact of noise can cause damage to hearing.
Total vibration values (vector sum of three directions) determined in accordance with EN 60745.
Handle:
Vibration emission value a
K uncertainty = 1.5 m/s
Additional handle:
Vibration emission value a
K uncertainty = 1.5 m/s
Additional information for electric power
tools
Warning!
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equipment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The speci ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Keep the noise emissions and vibrations to a
minimum.
Only use appliances which are in perfect wor-
•
king order.
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
•
cessary.
Switch the appliance off when it is not in use.
•
Wear protective gloves.
•
= 5.841 m/s
hAG
2
= 6.714 m/s
h
2
2
2
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain residual risks cannot be rules out. The following
hazards may arise in connection with the
equipment’s construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protection is used.
3. Health damage caused by hand-arm vibrations if the equipment is used over a prolonged period or is not properly guided and
maintained.
5. Before starting the equipment
Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
5.1 Fitting the additional handle (Fig. 2)
The angle grinder must not be used without
•
the additional handle (3).
The additional handle can be secured in any
•
of three positions (A, B, C).
Tool side Suitable for
shown)
5.2 Setting the guard (Fig. 3)
Switch off the tool. Pull the power plug.
•
Adjust the guard (4) to protect your hands
•
so that the material being ground is directed
away from your body.
sa / A noitisop( tfeL
sresu dednah-thgiR
sresu dednah-tfeL )B noitisop( thgiR
sleehw gnittuc gnisU )C noitisop( poT
•
to any specific working conditions. Undo the
clamp handle (a) and turn the cover (4) into
the required position.
Ensure that the guard (4) correctly covers the
•
gear wheel casing.
Secure the clamp handle (a) again.
•
Ensure that the guard (4) is secure.
•
detsujda eb nac )4( draug eht fo noitisop ehT
Anl_TE_AG_230_SPK1.indb 20 07.09.12 13:59
- 8 -
Page 9
GB
Take care that the safety device is secure.
Never use the angle grinder without the
guard.
5.3 Test run for new grinding Wheels
Allow the right-angle grinder to run in idle for at
least 1 minute with the grinding or cutting wheel
fitted in place. Vibrating wheels are to be replaced
immediately.
5.4 Swivel handle (Fig. 5)
The handle can be swiveled a maximum 90° to
the left and right. To do so, press the locking plate
(7) and swivel the handle 90° to the left or right.
Important. When the locking plate (7) engages
correctly it makes an audible click.
6. Operation
6.1 Switch (Fig. 4)
which is designed to prevent accidents. To start
the equipment push the locking lever (a) forwards,
then press the ON/OFF switch (3).
Wait until the machine has reached its top
speed. You can then position the angle grinder on the workpiece and machine it.
6.2 Changing the grinding wheels (Fig. 5 / 6)
Use the face spanner (5) supplied to change the
grinding wheels.
Important! For safety reasons, the angle grinder
must not be operated with the face spanner (5)
inserted in it.
Pull out the power plug.
Simple wheel change by spindle lock:
•
Press the spindle lock and allow the grinding
•
wheel to latch in place.
Open the flange nut with the face spanner.
•
(Fig. 6)
•
Change the grinding or cutting wheel and
•
tighten the flange nut with the face spanner.
Important!
Only ever press the spindle lock when the
motor and grinding spindle are at a standstill! You must keep the spindle lock pressed
while you change the wheel!
For grinding or cutting wheels up to approx. 3 mm
hctiws ytefas a htiw semoc rednirg elgna ehT
thick, screw on the
facing the grinding or cutting wheel.
6.3 Flange arrangements when using grinding wheels and cutting wheels (Fig.
7-10)
Flange arrangement when using a de-
•
pressed-centre or straight grinding wheel
(Fig. 8)
a) Clamping flange
•
b) Flange nut
•
Flange arrangement when using a de-
•
pressed-centre cutting wheel (Fig. 9)
a) Clamping flange
•
b) Flange nut
•
Flange arrangement when using a straight
•
cutting wheel (Fig. 10)
a) Clamping flange
•
b) Flange nut
•
6.4 Motor
It is vital for the motor to be well ventilated during
operation. Be sure, therefore, to keep the ventilation holes clean at all times.
6.5 Grinding Wheels
Never use a grinding or cutting wheel bigger
•
than the specified diameter.
Before using a grinding or cutting wheel,
•
check its rated speed.
The maximum speed of the grinding or cut-
•
ting wheel used must be higher than the idle
speed of the angle grinder.
Use only grinding and cutting wheels that are
•
approved for a minimum speed of 8.000 rpm
and a peripheral speed of 80 m/sec.
Check the direction of rotation when you use
•
diamond cutting wheels. The directional arrow
on the diamond cutting wheel must point in
the direction in which the tool rotates.
Take special care that the grinding/sanding
wheels are properly stored and transported.
Ensure that the grinding/sanding wheels are
never exposed to shock, jolts or sharp edges (for
example during transport or storage in a toolbox).
This could cause damage (such as cracks) to the
grinding/sanding wheels and place the user in
serious danger.
ange nut with the at side
Anl_TE_AG_230_SPK1.indb 21 07.09.12 13:59
- 9 -
Page 10
GB
6.6 Operating Modes
6.6.1 Rough grinding (Fig. 11)
Caution: Use the safety device for san-
ding/grinding (included in items supplied).
For the best rough grinding results, hold the grinding wheel at an angle of between 30° and 40° to
the workpiece surface and guide back and forth
over the workpiece in steady movements.
6.6.2 Cutting (Fig. 12)
Caution: Use the safety device for abrasi-
ve cutting (available as accessory, see 8.4)
When you use the right-angle grinder for cutting
purposes, avoid tilting it in the cutting plane. The
cutting wheel must have a clean cutting edge.
A diamond cutting wheel is best used to cut hard
stone.
It is prohibited to use the machine on as-
bestos materials!
Never use a cutting wheel for rough grin-
ding.
7. Replacing the power cable
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
8. Cleaning, maintenance and
ordering of spare parts
Always pull out the mains power plug before starting any cleaning work.
tack the plastic parts of the equipment. Ensure that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
8.2 Carbon brushes
In case of excessive sparking, have the carbon
brushes checked only by a quali ed electrician.
Important! The carbon brushes should not be rep
laced by anyone but a quali ed electrician.
8.3 Maintenance
There are no parts inside the equipment which
require additional maintenance.
8.4 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
•
•
•
enihcam fo epyT
enihcam eht fo rebmun elcitrA
enihcam eht fo rebmun noitacifitnedI
•
For our latest prices and information please go to
www.einhell.com.au
9. Disposal and recycling
The equipment is supplied in packaging to prevent it from being damaged in transit. The raw
materials in this packaging can be reused or
recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse. The equipment should
be taken to a suitable collection center for proper
disposal. If you do not know the whereabouts of
such a collection point, you should ask in your
local council offi ces.
deriuqer trap eht fo rebmun trap tnemecalpeR
8.1 Cleaning
•
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
immediately each time you have finished
using it.
•
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
Anl_TE_AG_230_SPK1.indb 22 07.09.12 13:59
eht dna stnev ria ,secived ytefas lla peeK
10. Storage
Store the equipment and accessories out of
children’s reach in a dark and dry place at above
freezing temperature. The ideal storage temperature is between 5 and 30 °C. Store the electric
ecived eht naelc uoy taht dnemmocer eW
tool in its original packaging.
tsiom a htiw ylraluger tnempiuqe eht naelC
- 10 -
Page 11
Warranty provisions
GB
replacement of the equipment in accordance with the overview below. Statutory guarantee claims are
unaffected.
Defect with regard to material or
construction
Wear parts* Carbon brushes 6 months
Consumables* Cutting wheels, grinding wheels Warranty only in case of an im-
* Not necessarily included in the scope of delivery!
For consumables, wear parts and missing parts Einhell Australia guarantees the correction of defects or
a new delivery only if the defect is reported within 24 hours (consumables), 5 work days (missing parts)
or 6 months (wear parts) after purchase and the purchase date is veri fied with the bill.
In case of defects concerning the material or construction, we kindly request you to submit the equipment together with the fully completed warranty card supplied with the equipment. It is important that
you enter an exact description of the defect.
To do so, answer the following questions:
Did the equipment work at all or was it defective from the beginning?
•
Did you notice anything (symptom or defect) prior to the failure?
•
What malfunction does the equipment have in your opinion (main symptom)?
•
Describe this malfunction.
24 months
mediate defect (24 hours after
purchase / date on the bill)
syad krow 5strap gnissiM
ro stcefed fo riaper eht seetnaraug esahcrup uoy edam uoy erehw erots YID eht ro Einhell Australia
ytnarraWelpmaxEyrogetaC
Anl_TE_AG_230_SPK1.indb 24 07.09.12 13:59
- 11 -
Page 12
GB
The guarantee provided in this Guarantee Certificate is given by Einhell Australia Pty Limited
ACN 134 632 858 of 6/166 Wellington Street, Collingwood, Victoria (Telephone number 1300 922 271)
(Einhell Express Guarantee).
GUARANTEE
Dear
Customer,
All of our products undergo strict quality checks. In the unlikely event that your device develops a fault, please
contact our service department at the address shown on this guarantee cert
prefer to call us then we are also happy to offer our assistance under the service number printed below.
Please note the following terms under which claims under the Einhell Express Guarantee can be made:
1. The benefits conferred by the Einhell Express Guarantee are in addition to all rights and remedies which
you may be entitled to under the Australian Consumer La
under other applicable laws. This Einhell Express Guarantee does not exclude, restrict or modify any
such rights or remedies.
We do not charge you for the Einhell Express Guarantee.
2. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are
entitled to a replacement or refund for a major failure and for compensation for any othe
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods
fail to be of acceptable quality and the failure does not amount to a major failure.
3. The Einhell Express Guarantee only covers problems caused by material or manufacturing defects, and
our liability under the Einhell Express Guarantee is limited, at our discretion, to the rectification of these
defects
or replacement of the product. Please note that the product has not b
commercial, trade or industrial applications. Consequently, the Einhell Express Guarantee will not apply
if the product is used in commercial, trade or industrial applications or for other equivalent activities.
4. The following are also excluded from the Einhell Express Guarantee: compensation for transport
damag
e, damage caused by failure to comply with the installation/assembly instructions or damage
caused by unprofessional installation, failure to comply with the op
the wrong mains voltage or current type), misuse or inappropriate use (such as overloading of the
product or use of non-approved tools or accessories), failure to comply with the maintenance and safety
regulatio
ns, ingress of foreign bodies into the product (e.g. sand, stones or dust), effects of force or
external influences (e.g. damage caused by the product being dropped) and normal wear resulting from
proper operation of the product. The Einhell Express Guarantee will also not apply if any attempt is made
to tamper with the
5. The Einhell Express Guarantee is valid for a period of 2 years starting from the purchase date of t
product. Claims made under the Einhell Express Guarantee should be submitted before the end of this
guarantee period and within two weeks of the defect being noticed. No claims under the Einhell Express
Guarantee will be accepted if submitted after the end of this guarantee period. The original guarantee
period remains applicable to the
cases, the work performed or parts fitted will not result in an extension of the guarantee period for the
Einhell Express Guarantee, and the Einhell Express Guarantee will not apply for the work performed or
parts fitted. This also applies when an on-site service is used.
6. To make a claim under the Einhell Express Guarantee, please send the relevant product postage-free to
the address shown below and enclose either the original or a copy of your sales receipt or another
proof of purchase. It would help us if you could describe the nature of the problem in as much detail as
possible. If the defect is covered by the Einhell Express Guarantee, your product will be repaired
immediately and returned to you, or we will send you a new device (at our election).
Any costs incurred by you in making a claim under this Einhell Express Guarantee, unless specified
otherwise in this
Of course, we are also happy to offer a chargeable repair service for any defects which are not covered by the
scope of the Einhell Express Guarantee or for products which are no longer covered by the Einhell Express
Guarantee. To take advantage of this service, please send the product to our service address.
product.
device even if repairs are carried out or parts are replaced. In suc
guarantee certificate, must be borne by you.
EINHELL AUSTRALIA PTY LTD
6/166 Wellington Street
Collingwood VIC 3066
Phone: 1300 922 271
CERTIFICATE
w, and any other statutory rights you may have
Australia
ificate. Of course, if you would
r reasonably
een designed for use in
erating instructions (e.g. connection to
EH 02/2013 (01)
he
h
d
ated
Anl_TE_AG_125_750_SPK1.indb 24 14.09.12 12:19
- 12 -
Loading...