EIC RGP02-14E, RGP02-16E, RGP02-18E, RGP02-20E, RGP02-12E Datasheet
RGP02-12E // 20E
FAST RECOVERY RECTIFIERS
PRV : 1200 - 2000 Volts
Io : 0.5 Ampere
FEATURES :
MECHANICAL DATA :
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Rating at 25
°
C ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%.
RGP
RGP
RGP
RGP
RGP
DO - 41
* Glass passivated junction
* High current capability
* High surge current capability
* High reliability
* Low reverse current
* Low forward voltage drop
* Fast switching for high efficiency
HIGH VOLTAGE
0.107 (2.7)
0.080 (2.0)
1.00 (25.4)
MIN.
0.205 (5.2)
0.166 (4.2)
* Case : DO-41 Molded plastic
* Epoxy : UL94V-O rate flame retardant
* Lead : Axial lead solderable per MIL-STD-202,
Method 208 guaranteed
* Polarity : Color band denotes cathode end
* Mounting position : Any
* Weight : 0.339 gram
RATING
Maximum Recurrent Peak Reverse Voltage VRRM 1200 1400 1600 1800 2000 Volts
Maximum RMS Voltage VRMS 840 980 1120 1260 1400 Volts
Maximum DC Blocking Voltage VDC 1200 1400 1600 1800 2000 Volts
Maximum Average Forward Current
0.375"(9.5mm) Lead Length Ta = 55 °C IF(AV) 0.5 Amps.
Peak Forward Surge Current 8.3 ms. Single half sine wave
Superimposed on rated load (JEDEC Method) IFSM 20 Amps.
Maximum Peak Forward Voltage at 0.5 Amp. VF 2.5 Volts
Maximum DC Reverse Current Ta = 25 °C IR 5.0 µA
at Rated DC Blocking Voltage Ta = 100 °C IR(H) 50 µA
Maximum Reverse Recovery Time ( Note 1 ) Trr 300 ns
Typical Junction Capacitance ( Note 2 ) CJ 5.0 pf
Junction Temperature Range TJ - 65 to + 150 °C
Storage Temperature Range TSTG - 65 to + 150 °C
SYMBOL
02-12E
0.034 (0.86)
0.028 (0.71)
Dimensions in inches and ( millimeters )
02-14E
02-16E
1.00 (25.4)
02-18E
MIN.
02-20E
UNITS
Notes :
( 1 ) Reverse Recovery Test Conditions : IF = 0.5 A, IR = 1.0 A, Irr = 0.25 A.
( 2 ) Measured at 1.0 MHz and applied reverse voltage of 4.0 VDC
UPDATE : APRIL 23, 1998
RATING AND CHARACTERISTIC CURVES ( RGP02-12E - RGP02-20E )
+
0
1.0
+ 0.5 A0- 0.25
- 1.0 A
1 cm
FIG.1 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM
50 Ω 10 Ω
D.U.T.
50 Vdc
(approx)
1 Ω
NOTES : 1. Rise Time = 7 ns max., Input Impedance = 1 megaohm, 22 pF.
2. Rise time = 10 ns max., Source Impedance = 50 ohms.
3. All Resistors = Non-inductive Types.
OSCILLOSCOPE
( NOTE 1 )
PULSE
GENERATOR
( NOTE 2 )
Trr
SET TIME BASE FOR 50/100 ns/cm
FIG.2 - DERATING CURVE FOR OUTPUT FIG.3 - MAXIMUM NON-REPETITIVE PEAK
RECTIFIED CURRENT FORWARD SURGE CURRENT
0.5
0.4
0.3
0.2
CURRENT, AMPERES
0.1
AVERAGE FORWARD OUTPUT
60Hz RESISTIVE OR INDUCTIVE LOAD
0 25 50 75 100 125 150 175 1 2 4 6 10 20 40 60 100
AMBIENT TEMPERATURE, ( °C)
25
20
15
10
CURRENT, AMPERES
5
PEAK FORWARD SURGE
0
8.3 ms SINGLE HALF SINE WAVE
NUMBER OF CYCLES AT 60Hz
Ta = 50 °C
FIG.4 - TYPICAL FORWARD CHARACTERISTICS FIG.5 - TYPICAL REVERSE CHARACTERISTICS
2.0
10
TJ = 100 °C
TJ = 25 °C
0.1
0.01
Pulse Width = 300 µs
2% Duty Cycle
TJ = 25 °C
1.0
0.1
FORWARD CURRENT, AMPERES
0.001
0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6
FORWARD VOLTAGE, VOLTS
0.01
REVERSE CURRENT, MICROAMPERES
80
100 1400 20 40 60 120
PERCENT OF RATED REVERSE
VOLTAGE, (%)
Loading...