E-FLITE UMX Spacewalker Instruction Manual

Page 1

Instruction Manual Bedienungsanleitung Manuel d’utilisation Manuale di Istruzioni

UMX™ Spacewalker

Page 2

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury.

This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision. Do not use with incompatible components or alter this product in any way outside of the instructions provided by Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.

Safety Precautions and Warnings

• Always keep a safe distance in all directions around your model to avoid collisions or injury. This model is controlled by a radio signal subject to interference from many sources outside your control. Interference can cause momentary loss of control.

• Always operate your model in open spaces away from full-size vehicles, trafﬁ c and people.

• Always carefully follow the directions and warnings for this and any optional support equipment (chargers, rechargeable battery packs, etc.).

• Always keep all chemicals, small parts and anything electrical out of the reach of children.

• Always avoid water exposure to all equipment not speciﬁ cally designed and protected for this purpose. Moisture causes damage to electronics.

• Never place any portion of the model in your mouth as it could cause serious injury or even death.

• Never operate your model with low transmitter batteries.

• Always keep aircraft in sight and under control.

• Always use fully charged batteries.

• Always keep the transmitter powered on while aircraft is powered.

• Always remove batteries before disassembly.

• Always keep moving parts clean.

• Always keep parts dry.

• Always let parts cool after use before touching.

• Always remove batteries after use.

• Always ensure failsafe is properly set before ﬂ ying.

• Never operate aircraft with damaged wiring.

• Never touch moving parts.

Age Recommendation: Not for children under 14 years. This is not a toy.

NOTICE

All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit www.horizonhobby.com and click on the support tab for this product.

Meaning of Special Language:

The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:

NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND little or no possibility of injury.

CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.

WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high probability of superﬁ cial injury.

Page 3

To register your product online, go to www.e-ﬂ iterc.com

11.6 in (295mm)

16.5 in (418mm)

Weight: 0.78 oz (22 g)

Wing Area: 45.3 in

(292 dm 2)

Table of Contents

Speciﬁ cations

Installed Installed 6mm Brushed Motor

Installed Installed

DSM2®/DSMX® Receiver/ESC

Installed Installed

(2) Servos on the Receiver/ESC Board

Included Included

70mAh 1S 3.7V 14C Li-Po battery

Included Included

1S 3.7V Li-Po Battery Charger

Included

Needed to Complete

DSM2/DSMX 4-Channel Transmitter

Preﬂ ight Checklist ..................................................4

Charging Warnings.................................................4

Battery Charging ....................................................5

Transmitter Batteries Installation ............................6

Transmitter and Receiver Binding ...........................6

Digital Trims ...........................................................7

Dual Rate Function ................................................7

Transmitter Control ................................................7

Flight Battery Installation and ESC Arming..............8

Center of Gravity (CG) Adjustment .........................8

Control Direction Test .............................................9

Control Centering ..................................................9

Control Horn Settings ...........................................10

Dual Rates ...........................................................10

Low Voltage Cutoff (LVC) ......................................10

Flying Tips and Repairs ........................................11

Post Flight Checklist ............................................11

Power Components Service .................................12

Troubleshooting Guide .........................................13

Troubleshooting Guide (Continued) .......................14

Limited Warranty .................................................14

Warranty and Service Information ........................15

FCC Information ...................................................16

ICC Information ....................................................16

Compliance Information for the European Union ...16

Replacement Parts ...............................................61

Optional Parts and Accessories ............................62

Page 4



1. Charge ﬂ ight battery.

2. Install ﬂ ight battery in aircraft (once it has been fully charged).

3. Bind aircraft to transmitter. (BNF only)

4. Make sure linkages move freely.

5. Perform Control Direction Test with transmitter.



6. Set dual rates and expos.

7. Adjust center of gravity.

8. Perform a radio system Range Check.

9. Find a safe and open area.

10. Plan ﬂ ight for ﬂ ying ﬁ eld conditions.

Preﬂ ight Checklist

Charging Warnings

The Battery Charger (EFLC1000) included with your aircraft has been designed to safely charge the Li-Po battery.

CAUTION: All instructions and warnings must be followed exactly. Mishandling of Li-Po batteries can result in a ﬁ re, personal injury and/or property damage.

• By handling, charging or using the included

Li-Po battery, you assume all risks associated with lithium batteries.

• If at any time the battery begins to balloon or

swell, discontinue use immediately. If charging or discharging, discontinue and disconnect. Continuing to use, charge or discharge a battery that is ballooning or swelling can result in ﬁ re.

• Always store the battery at room temperature

in a dry area for best results.

• Always transport or temporarily store the

battery in a temperature range of 40–120º F (5–49° C). Do not store the battery or model in a car or direct sunlight. If stored in a hot car, the battery can be damaged or even catch ﬁ re.

• Always charge batteries away from ﬂ ammable

materials.

• Always inspect the battery before charging.

• Always disconnect the battery after charging, and let the charger cool between charges.

• Always constantly monitor the temperature of the battery pack while charging.

• ONLY USE A CHARGER SPECIFICALLY DESIGNED TO CHARGE LI-PO BATTERIES. Failure to charge the battery with a compatible charger may cause a ﬁ re resulting in personal injury and/or property damage.

• Never discharge Li-Po cells to below 3V under load.

• Never cover warning labels with hook and loop strips.

• Never leave charging batteries unattended.

• Never charge batteries outside recommended levels.

• Never charge damaged batteries.

• Never attempt to dismantle or alter the charger.

• Never allow minors to charge battery packs.

• Never charge batteries in extremely hot or cold places (recommended between 40–120° F (5–49° C)) or place in direct sunlight.

Page 5

Your aircraft comes with a 1S 3.7V DC Li-Po battery charger and 1S 3.7V 70mAh 14C Li-Po battery. Refer to the charging warnings. It is recommended to charge the battery pack while you are inspecting the aircraft. The ﬂ ight battery will be required to conﬁ rm proper aircraft operation in future steps.

Remove the cover on the bottom of the charger and install four of the included AA batteries, noting proper polarity. Replace the cover after the AA batteries are installed. Only use alkaline AA batteries.

Battery Charging Process

NOTICE: Charge only batteries that are cool to the

touch and are not damaged. Look at the battery to make sure it is not damaged e.g., swollen, bent, broken or punctured.

1. Slide the battery into the slot on the charger and press it into the charge jack/connector located at the bottom of the slot. The end cap of the battery is specifically designed to allow the battery to fit into the slot one way (usually with the label on the battery facing outward) to prevent reverse polarity connection. However, check for proper alignment and polarity.

2. Always disconnect the flight battery from the charger immediately upon completion of charging.

CAUTION: Only use a charger speciﬁ cally designed to charge a Li-Po battery. Failure to do so could result in ﬁ re, causing injury or property damage.

CAUTION: Never exceed the recommended charge rate.

LED Indications

When you make the connection successfully, the LED on the charger turns solid red, indicating charging has begun.

Charging a fully discharged (not over-discharged) 70mAh battery takes approximately 20–30 minutes. As the battery nears full charge, the LED begins to blink. The intervals between blinks will increase as the battery comes closer to full charge.

When the LED blinks approximately every 20 seconds, the battery is ready to be removed. However, the battery can be left charging until the LED completely goes out for a maximum charge.

CHARGING (Solid Red) ...........................

READY (Blinking 20 sec. intervals) ........

MAX CHARGE (off) .................................

Purchase the optional AC to 6V DC 1.5 amp Power Supply (EFLC1005) to charge your battery pack without AA batteries.

CAUTION: Only use an E-ﬂ ite® 6V power supply (EFLC1005) with this charger. DO NOT use a 12V power supply or property damage and injury could occur.

If the LED stays on when the ﬂ ight battery is removed, the AA batteries in the charger are low.

CAUTION: Once charging is complete, immediately remove the battery. Never leave a battery connected to the charger.

Battery Charging

Page 6

Binding is the process of programming the receiver to recognize the GUID (Globally Unique Identiﬁ er) code of a single speciﬁ c transmitter. You need to ‘bind’ your chosen Spektrum™ DSM® technology equipped aircraft transmitter to the receiver for proper operation.

For a list of compatible DSM2/DSMX transmitters, please visit www.bindnﬂ y.com.

CAUTION: When using a Futaba® transmitter with a Spektrum DSM module, you must reverse the throttle channel and rebind. Refer to your Spektrum module manual for binding and failsafe instructions. Refer to your Futaba transmitter manual for instructions on reversing the throttle channel.

Transmitter and Receiver Binding



Binding Procedure Reference Table

1. Refer to your transmitter’s unique instructions for binding to a receiver.

2. Make sure the ﬂ ight battery is disconnected from the aircraft.

3. Ensure the transmitter is powered OFF.

4. Connect the ﬂ ight battery to the aircraft. The receiver LED will begin to ﬂ ash (typically after 5 seconds).

5. Make sure the transmitter controls are at neutral and the throttle is in the low position.

6. Put your transmitter into bind mode.

(If you are using the transmitter that is supplied with the RTF version, push the left control stick vertically into the case (until it clicks) while powering ON the transmitter).

7. After 5 to 10 seconds, the receiver status LED will become solid, indicating that the receiver is bound to the transmitter. If the LED does not turn solid, refer to the Troubleshooting Guide at the end of the manual.

For subsequent ﬂ ights, power ON the transmitter for 5 seconds before connecting the ﬂ ight battery.

Transmitter Batteries Installation

Your E-ﬂ ite® 4-channel DSM2®/ DSMX® RTF transmitter comes pre-bound to the aircraft.

Remove the cover, install four of the included batteries (noting proper polarity) and reinstall the cover.

Page 7

The E-ﬂ ite® 4-channel DSM2/DSMX transmitter features digital trim buttons on all controls to make ﬁ ne adjustments. The digital trims are used to ﬁ ne-tune the model’s ﬂ ight path when in ﬂ ight.

Before the ﬁ rst ﬂ ight, center the control surfaces mechanically (see Control Centering). When pressed down, trim buttons make a sound that increases or decreases in pitch at each pressing. The

middle or neutral trim position is heard as a middle tone in the pitch range of the sounds. The end of the control range is sounded by a series of beeps.

This transmitter’s dual rate feature lets you change between high and low control rates for the aileron, elevator and rudder.

• When powered ON, this transmitter is automatically set to high-rate mode.

• Change rate modes by pushing the right-hand control stick vertically into the case (until it clicks) while the transmitter is powered ON.

• High-rate mode is shown by the transmitter’s LED glowing solid red. In high-rate mode, the controls can reach their maximum values. This mode is typically preferred by experienced pilots for maximum control authority.

• Low-rate mode is shown by the transmitter’s LED blinking continuously. In low-rate mode, the controls are reduced to approximately 70% of their maximum values. This mode is typically preferred by (and best for) beginner pilots or others interested in smoother and more easily controlled ﬂ ight.

Mode 2

Throttle

Elevator/

Rudder

Rudder Trim

Throttle Trim Elevator Trim

Mode 1

Elevator

Throttle/

Rudder

Rudder Trim

Elevator Trim Throttle Trim

Transmitter Control

Digital Trims

Dual Rate Function

Page 8

Flight Battery Installation and ESC Arming

Arming the ESC also occurs after binding as previously described, but subsequent connection of a ﬂ ight battery requires the following steps.

It is normal for linear servos to make noise. Noise is not an indication of a faulty servo.

CAUTION: Always keep hands away from the propeller. When armed, the motor will turn the propeller in response to any throttle movement.

CAUTION: Always disconnect the Li-Po battery from the aircraft receiver when not ﬂ ying to avoid over-discharging the battery. Batteries discharged to a voltage lower than the lowest approved voltage may become damaged, resulting in loss of performance and potential ﬁ re when batteries are charged.

1-2-3-4-5 Sec.

Lower throttle and throttle trim to lowest settings.

Power ON the transmitter, then wait 5 seconds.

Connect the battery to the ESC, noting proper polarity.

Continuous LED

Secure the battery to the hook and loop strip on the

battery hold

er.

Refer to the Center of Gravity Adjustment instructions for the battery’s position.

FLY...

Center of Gravity (CG) Adjustment

The CG location is 18mm back from the leading edge at the wing root.

This CG location has been determined with the included 1S 70mAh 3.7V Li-Po battery installed in the battery cavity located on the bottom of the aircraft.

Balance the model on the edge of a metal ruler to ﬁ nd the Center of Gravity. Place the ruler on the underside of the airframe at the CG location shown in the image to the right. Move the battery forward or aft until the model closely balances at this location.

18mm

Page 9

Bind your aircraft and transmitter before doing these tests. Move the controls on the transmitter to make sure aircraft control surfaces move correctly. Always keep throttle at the low position during testing.

Down Elevator

Right Rudder

Left Rudder

Up Elevator

Control Direction Test

Before the ﬁ rst ﬂ ights, or in the event of an accident, make sure the ﬂ ight control surfaces are centered. Adjust the linkages mechanically if

the control surfaces are not centered. Use of the transmitter sub-trims may not correctly center the aircraft control surfaces due to the mechanical limits of linear servos.

1. Make sure the control surfaces are neutral when the transmitter controls and trims are centered. The transmitter sub-trim must always be set to zero.

2. When needed, use a pair of pliers to carefully bend the metal linkage (see illustration).

3. Make the U-shape narrower to make the connector shorter. Make the U-shape wider to make the linkage longer.

Control Centering

Page 10

Control Horn Settings

The table to the right shows the factory settings for the control horns. Fly the aircraft at factory settings before making changes.

After ﬂ ying, you may choose to adjust the linkage positions for the desired control response.

CAUTION: When these are incorrectly connected for the pilot’s skill level, unexpected aircraft response to controls can result. This can cause damage to the aircraft and personal injury.

Elevator Rudder

Dual Rates

To obtain the best ﬂ ight performance, we recommend using a DSM2/DSMX radio capable of adjustable Dual Rates. The suggested settings shown here are the recommended starting settings. Adjust according to the individual preferences after the initial ﬂ ight.

NOTICE: Do not set your transmitter travel adjust over 100%. If the TRAVEL ADJUST is set over

100%, it will not result in more control movement, it will overdrive the servo and cause damage.

Tip: For the ﬁ rst ﬂ ight, ﬂ y the model in low rate.

Dual Rate

High Low

Elevator 100% 70%

Rudder 100% 70%

When a Li-Po battery is discharged below 3V per cell, it will not hold a charge. The aircraft’s ESC protects the ﬂ ight battery from over-discharge using Low Voltage Cutoff (LVC). Once the battery discharges to 3V per cell, the LVC will reduce the power to the motor in order to leave adequate power to the receiver and servos to land the airplane.

When the motor power pulses, land the aircraft immediately and replace or recharge the ﬂ ight battery.

Always disconnect and remove the Li-Po battery from the aircraft after each ﬂ ight. Fully charge your Li-Po battery before storing it. Make sure the battery charge does not fall below 3V per cell. Failure to unplug a connected battery will result in trickle discharge and damage to the battery.

For your ﬁ rst ﬂ ights, set your transmitter timer or a stopwatch to 4 minutes. Adjust your timer for longer or shorter ﬂ ights once you have ﬂ own the model.

NOTICE: Repeated ﬂ ying to LVC will damage the battery.

Low Voltage Cutoff (LVC)

Page 11

We recommend ﬂ ying your aircraft inside a large gymnasium. We do not recommend ﬂ ying the aircraft outdoors unless the conditions are absolutely calm. The aircraft is extremely light and can be easily blown away.

Takeoff

Place the aircraft in position for takeoff (facing into the wind if ﬂ ying outdoors). Set dual rates to low position and gradually increase the throttle to ¾ to full and steer with the rudder. Pull back gently on the elevator and climb to a safe altitude to check trim. Once the trim is adjusted, begin exploring the ﬂ ight envelope of the aircraft.

Landing

Land into the wind. Fly the aircraft to approximately 6 inches (15cm) or less above the runway, using a small amount of throttle for the entire descent. Keep

the throttle on until the aircraft is ready to ﬂ are. During ﬂ are, keep the wings level and the airplane pointed into the wind. Gently lower the throttle while pulling back on the elevator to bring the aircraft down on all three wheels.

Failure to lower the throttle stick to the lowest possible positions during a crash could result in damage to the ESC in the receiver unit, which may require replacement.

NOTICE: Crash damage is not covered under the warranty.

Repairs

Repair the aircraft using foam-compatible CA (cyanoacrylate adhesive) or clear tape. Only use foam-compatible CA, as other types of glue can damage the foam. When parts are not repairable, see the Replacement Parts List for ordering by item number.

For a listing of all replacement and optional parts, refer to the list at the end of this manual.

NOTICE: Use of foam-compatible CA accelerant on your aircraft can damage paint. DO NOT handle the aircraft until the accelerant fully dries.

NOTICE: When you are ﬁ nished ﬂ ying, never leave the aircraft in direct sunlight or in a hot, enclosed area such as a car. Doing so can damage the foam.

Flying Tips and Repairs

Post Flight Checklist



1. Disconnect the ﬂ ight battery from the ESC (Required for safety and battery life).

2. Power OFF the transmitter.

3. Remove the ﬂ ight battery from the aircraft.



4. Recharge the ﬂ ight battery.

5. Store the ﬂ ight battery apart from the aircraft and monitor the battery charge.

6. Make note of the ﬂ ight conditions and ﬂ ight plan results, planning for future ﬂ ights.

NOTICE: Always decrease throttle at propeller strike.

Page 12

Power Components Service

110 x 60

CAUTION: DO NOT handle propeller parts while the ﬂ ight battery is connected. Personal injury could result.

Disassembly

1. Disconnect the battery from the

ESC/receiver.

2. Carefully cut the tape and/or decals on the

side of the fuselage to remove the top of the fuselage.

IMPORTANT: Removing tape and/or decals can remove paint from the fuselage.

3. Hold the prop shaft using needle-nose

pliers or hemostats.

4. Turn the propeller counterclockwise (facing

the front of the model) to remove. Turn the propeller clockwise to install.

5. Carefully remove the spinner

and glue from the propeller.

6. Hold the nut (A) on the end of the prop

shaft using needle-nose pliers or hemostats.

7. Turn the gear on the shaft clockwise (facing

the front of the model) to remove the nut.

8. Gently pull the shaft (B) from the gearbox (C)

and make sure the washer (D) and two bushings (E) are not lost.

9. Disconnect the motor from the ESC/

receiver.

10. Gently push the motor out of the gearbox

and remove the motor through the top of the fuselage behind the ESC/receiver.

NOTICE: DO NOT remove the gearbox from the aircraft. Damage to the aircraft could result.

Assembly

Assemble the aircraft using the instructions above in reverse order.

• Correctly align the prop shaft gear with the pinion

gear on the motor.

• Connect the motor to the ESC/receiver so

that the powered motor turns the propeller counterclockwise (facing the front of the model).

• Make sure the propeller size numbers (100 x 60)

face away from the motor (see illustration).

• Attach the spinner to the propeller using foam-

compatible CA (cyanoacrylate adhesive).

• Assemble the fuselage using clear tape.

100 x 60

Page 13

Problem Possible Cause Solution

Aircraft will not respond to throttle but responds to other controls

Throttle stick and/or throttle trim too high Reset controls with throttle stick and throttle

trim at lowest setting

Throttle channel is reversed Reverse throttle channel on transmitter Motor disconnected from receiver Open fuselage and make sure motor is

properly connected to the receiver

Extra propeller noise or extra vibration

Damaged propeller, prop shaft, spinner or motor

Replace damaged parts

Reduced ﬂ ight time or aircraft underpowered

Flight battery charge is low Completely recharge ﬂ ight battery Propeller installed backwards Install propeller with numbers facing forward Flight battery damaged Replace ﬂ ight battery and follow ﬂ ight battery

instructions Flight conditions may be too cold Make sure battery is warm before use Battery capacity too low for power drawn Replace battery or use a larger capacity

battery

LED on receiver ﬂ ashes and aircraft will not bind to transmitter (during binding)

Transmitter too near aircraft during binding process

Power off transmitter, move transmitter a

larger distance from aircraft, disconnect and

reconnect ﬂ ight battery to aircraft and follow

binding instructions Bind switch or button not held long enough

during bind process

Power off transmitter and repeat bind pro-

cess. Hold transmitter bind button or switch

until receiver is bound Aircraft or transmitter is too close to large

metal object, wireless source or another transmitter

Move aircraft and transmitter to another

location and attempt binding again

LED on receiver ﬂ ashes rapidly and aircraft will not respond to transmitter (after binding)

Less than a 5-second wait between ﬁ rst powering on transmitter and connecting ﬂ ight battery to aircraft

Leaving transmitter on, disconnect and

reconnect ﬂ ight battery to aircraft

Aircraft bound to different model memory (ModelMatch

™

radios only)

Select correct model memory on transmitter

and disconnect and reconnect ﬂ ight battery

to aircraft Flight battery/transmitter battery charge is

too low

Replace/recharge batteries

Transmitter may have been bound to a different model (or with a different DSM Protocol)

Select the right transmitter or bind to the

new one

Aircraft or transmitter is too close to large metal object, wireless source or another transmitter

Move aircraft and transmitter to another

location and attempt linking again

Control surface does not move

Control surface, control horn, linkage or servo damage

Replace or repair damaged parts and adjust

controls Wire damaged or connections loose Do a check of wires and connections, con-

nect or replace as needed Flight battery charge is low Fully recharge ﬂ ight battery Control linkage does not move freely Make sure control linkage moves freely

Controls reversed Transmitter settings reversed Adjust controls on transmitter appropriately

Troubleshooting Guide

Page 14

Problem Possible Cause Solution

Motor loses power Damage to motor or power components Do a check of motor and power components

for damage (replace as needed) Flight battery charge is too low Fully recharge ﬂ ight battery

Motor power quickly decreases and increases then motor loses power

Battery power is down to the point of receiver/ESC Low Voltage Cutoff (LVC)

Recharge ﬂ ight battery or replace battery that

is no longer performing

Servo locks or freezes at full travel

Travel adjust value is set above 100%, overdriving the servo

Set Travel adjust to 100% or less and/or set

sub-trims to Zero and adjust linkages

mechanically

Troubleshooting Guide (Continued)

What this Warranty Covers

Horizon Hobby, LLC (“Horizon”) warrants to the original purchaser that the product purchased (the “Product”) will be free from defects in materials and workmanship at the date of purchase.

What is Not Covered

This warranty is not transferable and does not cover (i) cosmetic damage, (ii) damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or due to improper use, installation, operation or maintenance, (iii) modiﬁ cation of or to any part of the Product, (iv) attempted service by anyone other than a Horizon Hobby authorized service center, (v) Product not purchased from an authorized Horizon dealer, or (vi) Product not compliant with applicable technical regulations.

OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.

Purchaser’s Remedy

Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be that Horizon will, at its option, either (i) service, or (ii) replace, any Product determined by Horizon to be defective. Horizon reserves the right to inspect any and all Product(s) involved in a warranty claim. Service or replacement decisions are at the sole discretion of Horizon. Proof of purchase is required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.

Limitation of Liability

HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF

PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in no event shall the liability of Horizon exceed the individual price of the Product on which liability is asserted. As Horizon has no control over use, setup, ﬁ nal assembly, modiﬁ cation or misuse, no liability shall be assumed nor accepted for any resulting damage or injury. By the act of use, setup or assembly, the user accepts all resulting liability. If you as the purchaser or user are not prepared to accept the liability associated with the use of the Product, purchaser is advised to return the Product immediately in new and unused condition to the place of purchase.

Law

These terms are governed by Illinois law (without regard to conﬂ ict of law principals). This warranty gives you speciﬁ c legal rights, and you may also have other rights which vary from state to state. Horizon reserves the right to change or modify this warranty at any time without notice.

WARRANTY SERVICES

Questions, Assistance, and Services

Your local hobby store and/or place of purchase cannot provide warranty support or service. Once assembly, setup or use of the Product has been started, you must contact your local distributor or Horizon directly. This will enable Horizon to better answer your questions and service you in the event that you may need any assistance. For questions or assistance, please visit our website at www. horizonhobby.com, submit a Product Support Inquiry, or call the toll free telephone number referenced in the Warranty and Service Contact Information section to speak with a Product Support representative.

Inspection or Services

If this Product needs to be inspected or serviced and is compliant in the country you live and use the Product in, please use the Horizon Online Service Request submission process found on our website or call Horizon to obtain a

Limited Warranty

Page 15

Warranty and Service Information

Country of Purchase Horizon Hobby Phone Number/Email Address Address

United States of

America

Horizon Service Center

(Repairs and Repair Requests)

servicecenter.horizonhobby.com/

RequestForm/

4105 Fieldstone Rd Champaign, Illinois,

61822 USA

Horizon Product Support

(Product Technical Assistance)

www.quickbase.com/db/

bghj7ey8c?a=GenNewRecord

888-959-2305

Sales

sales@horizonhobby.com

888-959-2305

United Kingdom

Service/Parts/Sales:

Horizon Hobby Limited

sales@horizonhobby.co.uk Units 1–4 , Ployters Rd,

Staple Tye Harlow, Essex,

CM18 7NS, United Kingdom

+44 (0) 1279 641 097

Germany

Horizon Technischer Service service@horizonhobby.de

Christian-Junge-Straße 1

25337 Elmshorn, Germany

Sales: Horizon Hobby GmbH +49 (0) 4121 2655 100

France

Service/Parts/Sales:

Horizon Hobby SAS

infofrance@horizonhobby.com

11 Rue Georges Charpak

77127 Lieusaint, France

+33 (0) 1 60 18 34 90

China

Service/Parts/Sales:

Horizon Hobby – China

info@horizonhobby.com.cn Room 506,

No. 97 Changshou Rd.

Shanghai, China 200060

+86 (021) 5180 9868

Return Merchandise Authorization (RMA) number. Pack the Product securely using a shipping carton. Please note that original boxes may be included, but are not designed to withstand the rigors of shipping without additional protection. Ship via a carrier that provides tracking and insurance for lost or damaged parcels, as Horizon is not responsible for merchandise until it arrives and is accepted at our facility. An Online Service Request is available at http://www.horizonhobby.com/content/_ service-center_render-service-center. If you do not have internet access, please contact Horizon Product Support to obtain a RMA number along with instructions for submitting your product for service. When calling Horizon, you will be asked to provide your complete name, street address, email address and phone number where you can be reached during business hours. When sending product into Horizon, please include your RMA number, a list of the included items, and a brief summary of the problem. A copy of your original sales receipt must be included for warranty consideration. Be sure your name, address, and RMA number are clearly written on the outside of the shipping carton.

NOTICE: Do not ship LiPo batteries to Horizon. If you have any issue with a LiPo battery, please contact the appropriate Horizon Product Support ofﬁ ce.

Warranty Requirements

For Warranty consideration, you must include your original sales receipt verifying the proof-of-purchase date. Provided warranty conditions have been met,

your Product will be serviced or replaced free of charge. Service or replacement decisions are at the sole discretion of Horizon.

Non-Warranty Service

Should your service not be covered by warranty, service will be completed and payment will be required without notiﬁ cation or estimate of the expense unless the expense exceeds 50% of the retail purchase cost. By submitting the item for service you are

agreeing to payment of the service without notiﬁ cation. Service estimates are available upon request. You must include this request with your item submitted for service. Non-warranty service estimates will be billed a minimum of ½ hour of labor. In addition you will be billed for return freight. Horizon accepts money orders and cashier’s checks, as well as Visa, MasterCard, American Express, and Discover cards. By submitting any item to Horizon for service, you are agreeing to Horizon’s Terms and Conditions found on our website http://www.horizonhobby. com/content/_service-center_render-service-center.

ATTENTION: Horizon service is limited to Product compliant in the country of use and ownership. If received, a non-compliant Product will not be serviced. Further, the sender will be responsible for arranging return shipment of the un-serviced Product, through a carrier of the sender’s choice and at the sender’s expense. Horizon will hold non-compliant Product for a period of 60 days from notiﬁ cation, after which it will be discarded.

Page 16

Declaration of Conformity

Compliance Information for the European Union

Robert Peak

Chief Financial Ofﬁ cer

Horizon Hobby, LLC

Instructions for disposal of WEEE by users in the European Union

This product must not be disposed of with other waste. Instead, it is the user’s responsibility to dispose of their waste equipment by handing it over to a designated collections point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and

ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city ofﬁ ce, your household waste disposal service or where you purchased the product.

(in accordance with ISO/IEC 17050-1) No. HH2014062203

Product(s): UMX Spacewalker BNF Item Number(s): EFLU2780 Equipment class: 1

The object of declaration described above is in conformity with the requirements of the speciﬁ cations listed below, following the provisions of the European R&TTE directive 1999/5/EC, EMC Directive 2004/108/EC and LVD Directive 2006/95/EC

EN 301 489-1 V1.9.2: 2012 EN 301 489-17 V2.1.1: 2009

EN60950-1:2006+A11:2009+A1:2010+A12: 2011

EN55022:2010 + AC:2011 EN55024:2010

Signed for and on behalf of: Horizon Hobby, LLC Champaign, IL USA June 22, 2014

(in accordance with ISO/IEC 17050-1) No. HH2014062202

Product(s): UMX Spacewalker RTF Item Number(s): EFLU2700, EFLU2700M1 Equipment class: 1

EN 300-328 V1.7.1: 2006 EN 301 489-1 V1.9.2: 2012 EN 301 489-17 V2.1.1: 2009

EN60950-1:2006+A11:2009+A1:2010+A12: 2011

EN55022:2010 + AC:2011 EN55024:2010

Signed for and on behalf of: Horizon Hobby, LLC Champaign, IL USA June 22, 2014

Robert Peak

Chief Financial Ofﬁ cer

Horizon Hobby, LLC

ICC Information

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

FCC Information

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAUTION: Changes or modiﬁ cations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This product contains a radio transmitter with wireless technology which has been tested and found to be compliant with the applicable regulations governing a radio transmitter in the 2.400GHz to 2.4835GHz frequency range.

Page 17

Replacement Parts – Ersatzteile –

– Pièces de rechange – Pezzi di ricambio –

Part # • Nummer Numéro • Codice

Description Beschreibung Description Descrizione

EFLU2702

Decal Sheet: UMX Spacewalker

Dekorbogen: UMX Spacewalker

Planche de décalcomanies: UMX Spacewalker

Foglio con decalcomanie: UMX Spacewalker

EFLU2703

Landing Gear Set: UMX Spacewalker

Fahrgestellsatz: UMX Spacewalker

Jeu de train d’atterrissage : UMX Spacewalker

Set carrello di atterraggio: UMX Spacewalker

EFLU2720

Main Wing Set: UMX Spacewalker

E-ﬂ ite UMX Spacewalker: Tragﬂ äche

Aile: UMX Spacewalker

Set ala principale: UMX Spacewalker

EFLU2726

Pushrod Set: UMX Spacewalker

E-ﬂ ite UMX Spacewalker: Gestänge

Set de tringlerie: UMX Spacewalker

Set rinvii: UMX Spacewalker

EFLU2725

Tail with Accessories: UMX Spacewalker

E-ﬂ ite UMX Spacewalker: Leitwerk m. Zbh.

Empennages avec accessoires: UMX Spacewalker

Coda con accessori.: UMX Spacewalker

EFLU2767

Fuselage with Windscreen: UMX Spacewalker

E-ﬂ ite UMX Spacewalker: Rumpf m. Scheibe

Fuselage avec pare-brise: UMX Spacewalker

Fusoliera con parabrezza: UMX Spacewalker

PKZ3901

Prop with Spinner (100mm x 60mm)

Parkzone Prop mit Spinner (100mm x 60mm)

Hélice avec cône (100mm x 60mm)

Elica con ogiva (100mm x 60mm)

PKZ3429

Prop Shaft with Gear

Parkzone Luftschraubenwelle und Getriebe

Axe d’hélice avec couronner

Albero elica con ingranaggio

PKZ3916

Motor 6mm Parkzone Motor

6mm

Moteur diamètre 6mm Motore 6mm

PKZ3928

Complete Gearbox Parkzone Getriebe

kpl.

Réducteur complet Riduttore completo

PKZ3904

Prop Shaft with Nut Parkzone Getriebe

kpl.

Axe d’hélice avec écrou

Albero elica con dado

EFLUP112903B

112 x 90mm 3 Blade Propeller

112 x 90mm3-Blattpropeller

Hélice 3pales 112 x 90mm

Elica 112 x 90 mm a 3 lame

EFLC1003

DC 3.7V Li-Po Charger

DC-3,7V-Li-PoLadegerät

Chargeur Li-Po DC 3,7V

Caricabatterie Li-Po CC da 3,7 V

EFLH1064B

2.4GHz Transmitter: MLP4DSM

2,4GHz-DSM2Sender: MLP4DSM

Émetteur 2,4GHz: MLP4DSM

Trasmettitore 2,4 GHz: MLP4DSM

EFLB0701S

70mAh 1S 3.7V 14C LiPo Battery

E-ﬂ ite 70mAh 1S

3.7V 14C LiPo Akku

Batterie Li-Po 1S 3.7V 70mA 14C

Batteria LiPo 70mAh 1S 3.7V 14C

PKZ3352

Receiver/ESC DSM2/X

Parkzone Empfänger/ReglerDSM2/X

Module RX/Vario DSM2/DSMX

Ricevitore/ESC DSM2/X

Page 18

– Optional Parts and Accessories –

– Optionale Bauteile und Zubehörteile –

– Pièces optionnelles et accessoires –

– Pezzi opzionali e accessori –

Part # • Nummer Numéro • Codice

Description Beschreibung Description Descrizione

PKZ1039

Hook and Loop Set (5): Ultra Micros

Parkzone: Klettband Set Ultra Micros

Ultras Micros - Bande auto-agrippante (5)

Set fascette a strappo (5): Ultra Micro

EFLC1004

Celectra 4-Port 1S

3.7V 0.3A DC Li-Po Charger

Celectra-1S-3,7V0,3A-DC-Li-PoLadegerät mit 4Anschlüssen

Chargeur Li-Po CC 0,3A 3, 7V 1S 4ports Celectra

Caricabatterie Li-Po 1S da 3,7 V 0,3 A CC, a 4porte, Celectra

EFLC1005/UK/ AU/EU

AC to 12V DC,1.5 Amp Power Supply (Based upon your sales Region)

Netzteil 12V 1,5 A (Basierend nach Vertriebsregion)

Alimentation CA vers 12V CC, 1,5 A (En fonction de votre région)

Alimentatore CA

- 12V CC da 1,5 A (in base al Paese di vendita)

DX5e DSMX 5-Channel Transmitter

DX5e DSMX 5-Kanal Sender

Emetteur DX5e DSMX 5 voies

DX5e DSMX Trasmettitore 5 canali

DX6 DSMX 6-Channel Transmitter

DX6 DSMX 6-Kanal Sender

Emetteur DX6 DSMX 6 voies

DX6 DSMX Trasmettitore 6 canali

DX7s DSMX 7-Channel Transmitter

Spektrum DX7s 7 Kanal Sender

Emetteur DX7s DSMX 7 voies

DX7s DSMX Trasmettitore 7 canali

DX8 DSMX Transmitter

Spektrum DX8 nur Sender

Emetteur DX8 DSMX 8 voies

DX8 DSMX Solo trasmettitore

DX9 DSMX Transmitter

Spektrum DX9 nur Sender

Emetteur DX9 DSMX 9 voies

DX9 DSMX Solo trasmettitore

Gen 2 DX18 (Voice 18) Transmitter

DX18 Gen. 2 Sender (Sprachausgabe)

DX18 Gen 2 (Vocale) Trasmettitore Gen 2

DX18 (Voce18)

Page 19

and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc. Futaba is a registered trademark of Futaba Denshi Kogyo Kabushiki Kaisha

Corporation of Japan. All other trademarks, service marks and logos are property of their respective owners.

US 7,898,130. US D578,146. PRC ZL 200720069025. PRC ZL 2007001249.

Other patents pending. www.e-ﬂ iterc.com

Created 6/14 39672

EFLU2700, EFLU2780

E-FLITE UMX Spacewalker Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual