Page 1
Description
Speaker
25 VRMS, 95 to 177 multi
white
Speaker
25 VRMS, 95 to 177
white, with FIRE marking
Speaker
70 VRMS, 95 to 177 multi
white
Speaker
70 VRMS, 95 to
white, with FIRE marking
Model name
Auto
Genesis Signal Master
Remote Mount
Genesis High Candela Ceiling Speaker-Strobe
Installation Sheet
Description
The Genesis High Candela Ceiling Speaker-Strobe is a fire
alarm notification appliance designed for indoor ceilings and
walls. See Table 1 for a list of model numbers.
Table 1: Models
Number
-Strobe,
-Strobe,
multi-cd,
-Strobe,
-Strobe,
177 multi-cd,
A field configurable jumper option is available for selecting the
desired strobe signal output.
The speaker-strobe includes field configurable switches for
selecting the desired candela and wattage outputs. These
output settings lock in place and remain visible after final
installation.
This strobe features an enhanced synchronization circuit to
comply with the latest requirements of UL 1971 Signaling
Devices for the Hearing Impaired and the latest Canadian
standard CAN/ULC-S526. Synchronized operation requires a
separately installed synchronization control module. See
Table 2 for a list of compatible synchronization modules.
Install this device in accordance with applicable requirements
in the latest editions of the NFPA codes and standards and
Canadian Electrical Code, Part 1, Section 32 and
CAN/ULC-S524, Standard for the Installation of Fire Alarm
Systems, and in accordance with the local authorities having
jurisdiction.
ADTGC-S2VMH MGC-S2VMH
-cd,
EGC-S2VMH XLSGC-S2VMH
GC-S2VMH ZGC-S2VMH
ADTGCF-S2VMH MGCF-S2VMH
EGCF-S2VMH XLSGCF-S2VMH
GCF-S2VMH ZGCF-S2VMH
ADTGC-S7VMH MGC-S7VMH
-cd,
EGC-S7VMH XLSGC-S7VMH
GC-S7VMH ZGC-S7VMH
ADTGCF-S7VMH MGCF-S7VMH
EGCF-S7VMH XLSGCF-S7VMH
GCF-S7VMH ZGCF-S7VMH
Table 2: Compatible synchronization module models
Number
-Sync Output Module
SIGA-CC1S SIGA-MCC1S
GSA-CC1S GSA-MCC1S
-
ADTG1M-RM MG1M-RM
EG1M-RM XLSG1M-RM
G1M-RM ZG1M-RM
Installation
WARNING: To reduce the risk of shock, disconnect all power
and allow 10 minutes for stored energy to dissipate before
handling.
Caution: Electrical supervision requires the wire run to be
broken at each terminal. Do not loop the signaling circuit field
wires around the terminals.
Note: When installed, these devices are not centered on the
electrical box. Make sure boxes are mounted to compensate
for this difference. See Figure 7.
To install the speaker-strobe:
1. Open the cover by depressing the tab on the side of the
unit with a small screwdriver. Hinge the cover down, to
access the mounting screws and selectable candela and
wattage switches. The cover is also detachable for
installation convenience.
2. If temporal strobe (private mode) operation is desired, cut
jumper JP1. See Figure 2.
3. Connect the speaker and strobe terminals to the signal
circuit field wiring. For the unit to function properly,
observe polarity. See Figure 4.
4. Slide the candela switch to the desired candela output (95,
115, 150, or 177 cd) by aligning it with the indicator below
the switch. See Figure 1.
5. Slide the wattage switch to the desired wattage tap (2 W,
1 W, 1/2 W, or 1/4 W) by aligning it with the indicator
below the switch. See Figure 1.
© 2013 UTC Fire & Security. All rights reserved. 1 / 4 P/N 3100615 • REV 05 • REB 30JAN13
6. Mount the unit onto a compatible electrical box. See
Figure 5.
Page 2
7. Replace the cover by positioning the alignment arrows
1. Candela switch
2. Indicator
3. Wattage switch
1. JP1: Strobe signal output: Cut to change from 1 flash per second
(public mode) to temporal (private mode)
1. Angle
Note: Horizontal and vertical outputs have the same pattern
1. From NAC output
2
3.
Note: Signal polarity is shown in the alarm condition.
100
959085
807570
656055
504540
3530252015
10
505
101520253035404550556065707580859095
100
0
5
10
15
20
25
30
35
40
45
50
55
60
65
70
75
80
85
90
-5
-10
-15
-20
-25
-30
-35
-40
-45
-50
-55
-60
-65
-70
-75
-80
-85
-90
1
2
together and rotating the cover clockwise.
8. Test the unit for proper operation.
Figure 1: Field-selectable switches
Figure 2: Strobe settings
Wiring
Figure 4: Wiring diagram
. To next NAC output
Amplifier output voltage matching the voltage ratings of the
speaker (25 or 70 VRMS)
Figure 5: Mounting diagram
Note: If the strobe is set to temporal (private mode), this
device is no longer UL 1971 or ULC-S526 Listed or FM
Approved but is UL 1638 Listed.
Figure 3: UL 1971 minimum light output (% of rating vs. angle)
2. Percentage of rated output
2 / 4 P/N 3100615 • REV 05 • REB 30JAN13
Page 3
Table 3: Strobe operating current in RMS (A)
VDC
VFWR
VDC = Volts direct current, regulated and filtered
VFWR = Volts full wave rectified
Operating currents shown above were measured by UL at 16 VDC and
16 VFWR.
1/4 W
1/2 W
1 W
2 W (UL)
2.2 W (ULC)
UL1480: Sound level output
reverberant room using 400 to 4,000 Hz band limited pink noise.
Directional characteristics: Within 6 dB of on
measured 90° off-axis (horizontal).
Operating voltage
Supervisory voltage
Strobe operating
current
Sound level output
Speaker response
Light output
Default settings
Wire size
Compatible electrical
boxes
Operating environment
Manufacturer
Year of
manufacture
UL/ULC rating
Environmental
class
Synchronization
Agency
[1] Nameplate marking is located on the inside surface of the device.
95 cd 115 cd 150 cd 177 cd
0.330 0.392 0.502 0.565
0.432 0.518 0.643 0.693
Table 4: Sound level output (dBA)
25V (UL) 25V (ULC) 70V (UL) 70V (ULC)
80 78 80 81
84 81 84 81
87 87 87 87
90 91
90 90
at 10 ft (3.05 m) measured in a
-axis sound level when
Figure 6: Light output profile
Perform a visual inspection and an operational test twice a
year or as directed by the local authority having jurisdiction.
Do no change the factory-applied finish.
Specifications
Speaker
Strobe
Selectable at 95, 115, 150, and 177 cd
1 flash per second (fps)
12 to 18 AWG (0.75 TO 2.50 mm²)
Temperature
Relative humidity
25 VRMS (model S2) or 70 VRMS (model S7)
24 VDC, 24 VFWR
30 V maximum
See Table 3
See Table 4
400 to 4,000 Hz
North American 4 in. square electrical box,
2-1/8 in. min. deep
32 to 120°F (0 to 49°C)
0 to 93% noncondensing
Regulatory information
Edwards, A Division of UTC Fire & Security
Americas Corporation, Inc.
8985 Town Center Parkway, Bradenton, FL
34202, USA
listings UL 1480. UL 1638 and UL 1971
The first two digits of the DATE MFG number
(located on the product identification label) are
the year of manufacture
Regulated 24 DC, regulated 24 FWR
This device was tested to the regulated
24 DC/FWR operating voltage limits of 16 V and
33 V. Do not apply 80% and 110% of these
values for system operation.
UL: Indoor dry
Meets UL 1971 requirements. Maximum allowed
resistance between any two devices is 20 Ω.
Refer to specifications for the synchronization
control module, this strobe, and the control panel
to determine allowed wire resistance.
CAN/, ULC-S541, ULC S526
BS EN 60065:2002 [1]
Maintenance
This unit is not serviceable or repairable. Should the unit fail to
operate, contact the supplier for replacement.
P/N 3100615 • REV 05 • REB 30JAN13 3 / 4
Contact information
For contact information, see www.edwardsutcfs.com.
Page 4
Figure 7: Mounting template
1. Center of ceiling tile or speaker/strobe
2.
3. Electrical box
4. Speaker
Cut line for location of electrical box
Mounting template
To center the speaker-strobe:
1. Position the template to the center of the ceiling tile.
2. Orient the strobe to the desired visual position.
9. Mark the location for the electrical box.
5. Strobe
4 / 4 P/N 3100615 • REV 05 • REB 30JAN13
Loading...