• 120V, 60Hz, 70W, 5 Oz (142 gm)
• TEMP. RANGE: 400°F - 800°F (205°C - 427°C)
• TEMP. REGULATION: ±6°F (±3°C)
• TIP TO GROUND LEAKAGE: < 2MV
• TIP TO GROUND RESISTANCE: < 2 OHMS
• COMPLIES WITH DOD-STD-2000-1B, MILSTD-2000A and ESD SPEC. DOD-STD 1868,
DOD-HDBK-263
LISTED
made
in
U S A
935 Soldering Station
includes CL1080 , PD528 and PS536
Sponge Holder
Power Switch
930 Soldering Station
includes CL1080 and IP329
WICK AND SOLDER SUPPLIES SOLD
SEPARATELY
PD528 Tool Holder
not included with PS536
Sponge Holder
IP329
Tool Base
PS536
Power Supply
TIP CARE
1. Plug-in Tool. Set to desired temperature. (Blinking lamp means
set temperature is reached.)
2. TIN the Tip (apply solder) before soldering.
3. Do not rub, bend or file Tip.
4. Always clean the Tip by wiping it against the saturated sponge,
then re-tin.
5. ALWAYS RE-TIN THE TIP BEFORE AND AFTER USING.
Temp. Regulation
Temp. Control
CL1080
LONER
®
Temperature Controlled
SOLDERING INSTRUMENT
120 VAC
Receptacle
RS372
Retaining Sleeve
Hollow Heater
Soldering Tip
Burn Resistant
CHANGING TIP
RS372
soldering tip
1. MAKE SURE YOUR TOOL IS
COOL!
2. Turn RS372 counterclockwise to remove.
3. Remove old Soldering Tip.
4. Insert new Tip.
5. Install RS372. (should be
"finger" tight only.)
SOLDERING TIPS
Iron Plated for long life•Nickel and
Chrome Plated for optimum heat transfer
CONTACT EDSYN FOR MORE SELECTIONS b
a
a
b
Large and heavy tip for
heavy duty soldering.
Fine point tip for SMD
soldering.
.03 (0.8 mm) .48 (12.2 mm)
.06 (1.5 mm) .48 (12.2 mm)
.02 (0.5 mm) 1.13 (28.8 mm)
.07 (2.0 mm) .93 (23.6 mm)
.03 (0.8 mm) .48 (12.2 mm)
.10 (2.5 mm) .74 (18.8 mm)
.06 (1.5 mm) 1.21 (30.7 mm)
.04 (1.0 mm) 1.21 (30.7 mm)
.20 (4.9 mm) .93 (23.6 mm)
.32 (8.3 mm) .97 (21.1 mm)
LT374 Standard Probe
LT375 Standard Spade
LT392 Extra-Long Needle Point
LT394 Extra-Long Spade
LT446 SMD Probe
LT337BC Heavy Duty Terminal Spade
LT223BC Heavy Duty Fine Spade
LT222BC Extra long Needle Point
LT153BH Jumbo Spade
LT155BH Jumbo Angle Spade
SET-UP & REQUIRED ACCESSORIES FOR HEAVY DUTY AND JUMBO TIPS
Apply AN112 or
AN122* Anti-Seize
Compound to Heater
and area of Tip contact.
"BC" HEAVY DUTY TIP
AC735
TA350
JUMBO TIP
RS351
RS271
*AN122 Anti-Seize Compound comes in
syringe dispenser.
To replace Pod, press Release Tab
and slide out Pod.
pull
PD528
LN230
SH230-1
CAUTION:
Over-filling can cause thermal shock to the tip or
heating element during tip cleaning.
RS243
RS199
• Replace RS199 Cleaning Sponge
1. Fill water only up to the top of the RS243 Leveling Pad.
2. Depress RS199 to moisten it completely.
• Replace SC581 Solder Collector
1. Hold the Housing firm and turn Cap counter-clockwise
and pull it away from the Housing.
2. Remove used SC581 and replace with a new one.
3. Reassemble Pod with TOP of the Cap in proper position.
MAINTENANCE
SC581
SR043
Front Housing
SR042
Thermal Housing
press
Loading...