971DX-230/B/P/I instruction manual
. E$;.ngineering
Oedicated to
Suit
'-.-~our
~eeds
@
g
Intellectual
Property
THE NAMESLONER, SOLDAPULLT,SOLDAVAC,ATMOSCOPE
AUTO-VAC,IDLE-REST,OCTAVACAND KLATCH
ARE REGISTEREDTRADEMARKSOF EDSYN,INC.
MOST PRODUCTSARECOVERED BYU.S. AND
FOREIGNPATENTSAND PENDINGAPPLICATIONS.
DESIGN, COLOR AND MATE RIALS
SUBJECT TO CHANGE WITHOUT NOTICE.
TIP STYLE ONSOLDERING,DESOLDERINGAND HOTAIR TOOLS MAYVARY.
PRINTED lN U.S.A.
f:E3:»S,Y":H'"@
.._thepower of precision
15958 ARMINTA ST. VAN NUYS. CA 91406-1896
PHONE: (818) 989-2324 FAX (sales): 818-997-0895
Email:info@edsyn.com Internet:www.edsyn.com
@ Copyright EDSYN. Inc. 2002
FORM.925
RevE
EDSYN@
971DX-230
1:
LONER@highperformance
Deluxe
SOLDERING STATION
COMPLIESWITHDOD-STD-2000-18
MIL-STD-2000Aand ESDSPEC.
DOD-STD1868,DOD HD8K-263
t(€1EMC Directive89/3361
~EEC
1
input
230V
,....-.......
/ "
1 \
1 MADElN THE 1
\ U.S.A. /
" /
/
instruction manual
971 DX-230/B/P/I
LON ER@ high performance
TemperatureControlled
SOLDERINGSTATION
2-N
controliedOutput
RCS71 Retaining Collar
Sleeve Assy.
fVl
~
ESDSAFE
For 971DX-230P
POWERCORD WlRING
BROWN 10 LINE
BLUE 10 NEUTRAl
GRNIYEl 10 GROUND
FO',
For 971DX.230B
M'~O~
For 971 DX-2301
WARNING: DO NOT HIT OR TAP THE TOOL.
HEA TER ELEMENT WILL BREAK/1/
PLACE TOOL lN TOOL POO WHEN NOT lN USE.
TEMPERATURE CALIBRA TION
AIR MOVEMENTWILL AFFECTTHE TEMPERATURE
READING. WORK lNANAREA WHERE THIS ISMINIMAL.
1. Turn on power and set TemperatureControl
Knobto205°C. ,
2. Using a clean and weil tinned Tip, apply a
small amount of solder on the Tip, just
enough to form a bead on top of the Tip.
3. Place the center of the thermocouple wire
of the SDS100 on top of the bead.
4. Again, apply a small amount of solder on
the center of the thermo-couple wire, just
enough to embed the center.
5. Adjust LO-Temp. Calibration Pot so the
Meter will read 205°C.
6. Set Temperature Contrai Knob to 427°C.
7. Adjust Hi-Temp. Calibration Pot so the
Meter will read 427°C.
fc(\EMC Directive 89/336/
~EEC
PD528
TooiPOO
Power Switch
TIP CARE
1. Set desired temperature. Blinking Lamp means Tooi is regulating.
2. TIN the Tip. (apply solder)
3. Do not rub, bend or reshape the Tip.
4. Always clean the Tip by wiping it against the saturated sponge and always RE-TIN.
ITEMSINCLUDED
SC581
~
1. PD528
BASIC DIMENSIONS
i.
l"~ y' Il'
81/4" 8il
(209 mm)
11--
~ 41/8,,:J
(121 mm)
B
3.LT375
4. WP556
71/2"
(191 mm)
~-1"
l,
1'''''- 10"
i--- (254mm)
-
SPECIFICATIONS
.230V input, 24V output, 50/60Hz, 70W
. 4 Ibs. (1.8 kg.)
. TEMP. RANGE: 400°F - 800°F (205°C - 427°C)
. TEMP.REGULATION::l:6°F(:l:3°C}
. TIP TOGROUNDLEAKAGE:< 2MV
.TIPTOGROUNDRESISTANCE:<20HMS
.COMPLIES WITH DOD-STD-2000-1 B MIL-STD-2000A and ESD SPEC.
DOD-STD1868,DODHDBK-263
. Tooi wt. 3 oz. (85 g)
. Tooi cord, 3 ft. (91.4 cm)
~Di'edM>8a'3:3&EEC
Loading...