Edimax Technology IR-123E User Manual

IR-113E/IR-123E

Quick Installation Guide

01-2013 / v1.0

Notice According to GNU General Public License Version 2

This product includes software that is subject to the GNU General Public License version

2. The program is free software and distributed without any warranty of the author. We
offer, valid for at least three years, to give you, for a charge no more than the costs of
physically performing source distribution, a complete machine-readable copy of the
corresponding source code.

The GNU GPL and GNU LGPL software codes used in Edimax products are distributed
without any warranty and are subject to the copyrights of their respective authors. The

firmware files for this product can be found under the “Download” page at the Edimax

website (www.edimax.com).

COPYRIGHT

Copyright  Edimax Technology Co., Ltd. all rights reserved. No part of this publication
may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated
into any language or computer language, in any form or by any means, electronic,
mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written
permission from Edimax Technology Co., Ltd.

Edimax Technology Co., Ltd. makes no representations or warranties, either expressed or
implied, with respect to the contents hereof and specifically disclaims any warranties,
merchantability, or fitness for any particular purpose. Any software described in this
manual is sold or licensed as is. Should the programs prove defective following their
purchase, the buyer (and not this company, its distributor, or its dealer) assumes the
entire cost of all necessary servicing, repair, and any incidental or consequential damages
resulting from any defect in the software. Edimax Technology Co., Ltd. reserves the right
to revise this publication and to make changes from time to time in the contents hereof
without the obligation to notify any person of such revision or changes.

The product you have purchased and the setup screen may appear slightly different from
those shown in this QIG. For more information about this product, please refer to the
user manual on the CD-ROM. The software and specifications are subject to change
without notice. Please visit our website www.edimax.com for updates. All brand and
product names mentioned in this manual are trademarks and/or registered trademarks
of their respective holders.

1

PRODUCT INTRODUCTION

No.

Description

1

Blue, sensor in 1, for alarm input, DV 3.3 volt level allowed

2

Yellow, RS-485 D-

3

Orange, RS-485 D+

4

Black, GND

5

Green, alarm out 1, DV 3.3 volt level allowed

6

DC 12 volt 2A input

7

Reset button

8

Audio output

9

Audio input

10

RJ-45 network connector
LED indicators: power (orange), network (green)

11

TV output, BNC connector

Package Contents

Before you start using this product, please check if there is anything missing
from the package:

 1 x Network camera
 1 x Power adapter
 1 x Sun shield
 2 x Screw
 1 x CD (with utility software, user manual & multi-language QIG)
 1 x Quick installation guide
 1 x Bracket

Connection Types

Note: Please check the attached I/O cable index before inserting or
releasing any wire.

2

No.

Description

1

IR LEDs for illumination in night mode

2

Day and night mode sensor for IR LED on/off control

3

Fixed focal lens

Front

INSTALLATION

1. Before powering on the camera, find the screws in the package and use a

screwdriver to fix the sun shield onto the device’s main body.

2. Secure the wall mount bracket onto the wall, and then secure the camera

onto the bracket.

3

Note: The bracket is an optional accessory.

3. Connect the network camera to a router/switch in the network via the

Ethernet port.

4. Connect the power adapter to the network camera’s power connector.

5. Plug the power adapter into a power outlet.

6. You should see the green LED on the RJ-45 port light up. If not, please

recheck every step and try again, or contact your dealer for assistance.

Note: The IR-113E/IR-123E (PoE model) supports the IEEE 802.3af PoE
standard. It can be powered via the Ethernet cable when connected to
a PoE switch.

ACCESSING THE NETWORK CAMERA’S MANAGEMENT INTERFACE

By default, the network camera automatically obtains an IP address from the

DHCP server on your local network. Check your DHCP server’s IP address lease
table to find the network camera’s IP address, or use the EdiView Finder utility

included in the CD.

1. Insert the CD into your CD-ROM drive. When the wizard appears, click

“Setup Utility” to install the “EdiView Finder” software.

4